summaryrefslogtreecommitdiffstats
path: root/net/mac80211/cfg.c
AgeCommit message (Collapse)AuthorFilesLines
2013-12-16mac80211: read station mgmt keys via get_key callMax Stepanov1-1/+2
Allow to read management keys stored in a station's gtk key array with a get_key function. Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16mac80211: check pairwise key_idx on get_key callMax Stepanov1-2/+2
Verify that a pairwise key index value on ieee80211_get_key call doesn't exceed the boundaries of the pairwise key array. Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16mac80211: refactor ieee80211_ibss_process_chanswitch()Luciano Coelho1-2/+2
Refactor ieee80211_ibss_process_chanswitch() to use ieee80211_channel_switch() and avoid code duplication. Tested by: Simon Wunderlich <sw@simonwunderlich.de> Acked by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16mac80211: make ieee80211_assign_beacon() staticLuciano Coelho1-2/+2
This function is not used anywhere else than in cfg.c, so there's no need to export it. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16mac80211: free all AP/VLAN keys at onceJohannes Berg1-4/+1
When the AP interface is stopped, free all AP and VLAN keys at once to only require synchronize_net() once. Since that does synchronize_net(), also move two such calls into the function (using the new force_synchronize parameter) to avoid doing it twice. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16mac80211: optimise mixed AP/VLAN station removalJohannes Berg1-3/+1
Teach sta_info_flush() to optionally also remove stations from all VLANs associated with an AP interface to optimise the station removal (in particular, synchronize_net().) To not have to add the vlans argument throughout, do some refactoring. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16mac80211: don't delay station destructionJohannes Berg1-7/+3
If we can assume that stations are never referenced by the driver after sta_state returns (and this is true since the previous iwlmvm patch and for all other drivers) then we don't need to delay station destruction, and don't need to play tricks with rcu_barrier() etc. This should speed up some scenarios like hostapd shutdown. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16Merge remote-tracking branch 'wireless-next/master' into mac80211-nextJohannes Berg1-4/+11
2013-12-06Merge branch 'master' of ↵John W. Linville1-4/+11
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/brcm80211/Kconfig net/mac80211/util.c
2013-12-05cfg80211: in bitrate_mask, rename mcs to ht_mcsJanusz Dziedzic1-2/+2
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also rename mcs to ht_mcs in struct cfg80211_bitrate_mask. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> [reword commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02mac80211: don't leak next beacon when csa is abortedSimon Wunderlich1-0/+3
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02mac80211: don't cancel csa finalize work within stop_apSimon Wunderlich1-1/+0
The current channel switch code has a potential deadlock: 1) * cfg80211_stop_ap acquires wdev-lock * ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work, which acquires the associated worker-lock 2) * ieee80211_csa_finalize_work holds the worker-lock when run * it calls cfg80211_ch_switch_notify which will claim the wdev-lock, and also needs to claim the sdata-lock (which is the same as the wdev-lock) to modify the beacons. It is sufficient to just set the channel switch active to false. If the worker is running later, it will find the channel switch to not be active anymore and returns immediately without changing anything. Canceling the worker is done anyway when the interface goes down (ieee80211_do_stop). Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02cfg80211/mac80211/ath6kl: acquire wdev lock outside ch_switch_notifySimon Wunderlich1-6/+15
The channel switch notification should be sent under the wdev/sdata-lock, preferably in the same moment as the channel change happens, to avoid races by other callers (e.g. start/stop_ap). This also adds the previously missing sdata_lock protection in csa_finalize_work. Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02mac80211: modify beacon using sdata/wdev-lock, not rtnl lockSimon Wunderlich1-8/+12
The csa finalize worker needs to change the beacon information (for different modes). These are normally protected under rtnl lock, but the csa finalize worker is called by drivers and should not acquire the RTNL lock. Therefore change access protection for beacons to sdata/wdev lock. Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> [fix sdata_dereference] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-02cfg80211: aggregate mgmt_tx parameters into a structAndrei Otcheretianski1-14/+15
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params struct to aggregate parameters for mgmt_tx functions. This makes the functions' signatures less clumsy and allows less painful parameters extension. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> [fix all other drivers] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25mac80211: move csa_chandef to sdataLuciano Coelho1-5/+4
There is no reason why we should have only one channel switch announcement at a time for a single phy. When support for channel switch with multiple contexts and multiple vifs per context is implemented, we will need the chandef data for each vif. Move the csa_chandef structure to sdata to prepare for this. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> [Fixed compilation with mesh] Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25mac80211: use put_unaligned_le16 in mesh_plink_frame_txChun-Yeow Yeoh1-2/+2
Use put_unaligned_le16 in mesh_plink_frame_tx. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25mac80211: add generic cipher scheme supportMax Stepanov1-6/+25
This adds generic cipher scheme support to mac80211, such schemes are fully under control by the driver. On hw registration drivers may specify additional HW ciphers with a scheme how these ciphers have to be handled by mac80211 TX/RR. A cipher scheme specifies a cipher suite value, a size of the security header to be added to or stripped from frames and how the PN is to be verified on RX. Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25cfg80211/mac80211: DFS setup chandef for cac eventJanusz Dziedzic1-1/+4
To report channel width correctly we have to send correct channel parameters from mac80211 when calling cfg80211_cac_event(). This is required in case of using channel width higher than 20MHz and we have to set correct dfs channel state after CAC (NL80211_DFS_AVAILABLE). Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25mac80211: fix the mesh channel switch supportChun-Yeow Yeoh1-1/+9
Mesh STA receiving the mesh CSA action frame is not able to trigger the mesh channel switch due to the incorrect handling and comparison of mesh channel switch parameters element (MCSP)'s TTL. Make sure the MCSP's TTL is updated accordingly before calling the ieee80211_mesh_process_chnswitch. Also, we update the beacon before forwarding the CSA action frame, so MCSP's precedence value and initiator flag need to be updated prior to this. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25mac80211: fix for mesh beacon update on powersaveJavier Lopez1-1/+1
Mesh beacon was not being rebuild after user triggered a mesh powersave change. To solve this issue use ieee80211_mbss_info_change_notify instead of ieee80211_bss_info_change_notify. This helper function forces mesh beacon to be rebuild and then notifies the driver about the beacon change. Signed-off-by: Javier Lopez <jlopex@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25Revert "mac80211: allow disable power save in mesh"Bob Copeland1-2/+1
This reverts commit ee1f668136b2fb6640ee2d54c2a525ea41f98211. The aformentioned commit added a check to allow 'iw wlan0 set power_save off' to work for mesh interfaces. However, this is problematic because it also allows 'iw wlan0 set power_save on', which will crash in short order because all of the subsequent code manipulates sdata->u.mgd. The power-saving states for mesh interfaces can be manipulated through the mesh config, e.g: 'iw wlan0 set mesh_param mesh_power_save=active' (which, despite the name, actualy disables power saving since the setting refers to the type of sleep the interface undergoes). Cc: stable@vger.kernel.org Fixes: ee1f668136b2 ("mac80211: allow disable power save in mesh") Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-05Merge branch 'for-john' of ↵John W. Linville1-6/+136
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Conflicts: net/wireless/reg.c
2013-11-04Merge branch 'master' of ↵John W. Linville1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/iwlwifi/pcie/drv.c
2013-10-28mac80211: fix uninitialized variableMichal Kazior1-1/+1
CSA completion could call in a driver bss_info_changed() with a garbled `changed` flag leading to all sorts of problems. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-28{nl,cfg,mac}80211: implement mesh channel switch userspace APIChun-Yeow Yeoh1-1/+8
Implement the required procedures for mesh channel switching as defined in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA and MCSP elements as followed: * Add the function for updating the beacon and probe response frames with CSA and MCSP elements during the period of switching to the new channel. Both CSA and MCSP elements must be included in beacon and probe response frames until the intended channel switch time. * The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements will then be removed from the beacon or probe response frames once the new channel is switched to. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-28{nl,cfg,mac}80211: enable the triggering of CSA frame in meshChun-Yeow Yeoh1-0/+21
Allow the triggering of CSA frame using mesh interface. The rules are more or less same with IBSS, such as not allowed to change between the band and channel width has to be same from the previous mode. Also, move the ieee80211_send_action_csa to a common space so that it can be re-used by mesh interface. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-28mac80211: fixes for mesh powersave logicMarco Porsch1-2/+2
This patch fixes errors in the mesh powersave logic which cause that remote peers do not get peer power mode change notifications and mesh peer service periods (MPSPs) got stuck. When closing a peer link, set the (now invalid) peer-specific power mode to 'unknown'. Avoid overhead when local power mode is unchanged. Reliably clear MPSP flags on peering status update. Avoid MPSP flags getting stuck by not requesting a further MPSP ownership if we already are an MPSP owner. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-28mac80211: implement SMPS for APEmmanuel Grumbach1-3/+105
When the driver requests to move to STATIC or DYNAMIC SMPS, we send an action frame to each associated station and reconfigure the channel context / driver. Of course, non-MIMO stations are ignored. The beacon isn't updated. The association response will include the original capabilities. Stations that associate while in non-OFF SMPS mode will get an action frame right after association to inform them about our current state. Note that we wait until the end of the EAPOL. Sending an action frame before the EAPOL is finished can be an issue for a few clients. Clients aren't likely to send EAPOL frames in MIMO anyway. When the SMPS configuration gets more permissive (e.g. STATIC -> OFF), we don't wake up stations that are asleep We remember that they don't know about the change and send the action frame when they wake up. When the SMPS configuration gets more restrictive (e.g. OFF -> STATIC), we set the TIM bit for every sleeping STA. uAPSD stations might send MIMO until they poll the action frame, but this is for a short period of time. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> [fix vht streams loop, initialisation] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-02mac80211: implement STA CSA for drivers using channel contextsArik Nemtsov1-0/+5
Limit the current implementation to a single channel context used by a single vif, thereby avoiding multi-vif/channel complexities. Reuse the main function from AP CSA code, but move a portion out in order to fit the STA scenario. Add a new mac80211 HW flag so we don't break devices that don't support channel switch with channel-contexts. The new behavior will be opt-in. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-09-30mac80211: use sta_info_get_bss() for nl80211 tx and client probingFelix Fietkau1-1/+1
This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-09-26mac80211: add support for CSA in IBSS modeSimon Wunderlich1-23/+64
This function adds the channel switch announcement implementation for the IBSS code. It is triggered by userspace (mac80211/cfg) or by external channel switch announcement, which have to be adopted. Both CSAs in beacons and action frames are supported. As for AP mode, the channel switch is applied after some time. However in IBSS mode, the channel switch IEs are generated in the kernel. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-16Merge branch 'for-john' of ↵John W. Linville1-2/+13
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-08-12mac80211: add vif to testmode cmdDavid Spinadel1-1/+10
Pass the wdev from cfg80211 on to the driver as the vif if given and it's valid for the driver. Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-12cfg80211: add wdev to testmode cmdDavid Spinadel1-1/+3
To allow drivers to implement per-interface testmode operations more easily, pass a wdev pointer if any identification for one was given from userspace. Clean up the code a bit while at it. Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-09Merge branch 'for-john' of ↵John W. Linville1-2/+185
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-08-01Merge branch 'for-john' of ↵John W. Linville1-27/+18
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-08-01mac80211: add channel switch command and beacon callbacksSimon Wunderlich1-2/+185
The count field in CSA must be decremented with each beacon transmitted. This patch implements the functionality for drivers using ieee80211_beacon_get(). Other drivers must call back manually after reaching count == 0. This patch also contains the handling and finish worker for the channel switch command, and mac80211/chanctx code to allow to change a channel definition of an active channel context. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> [small cleanups, catch identical chandef] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-16mac80211: select and adjust bitrates according to channel modeSimon Wunderlich1-27/+18
The various components accessing the bitrates table must use consider the used channel bandwidth to select only available rates or calculate the bitrate correctly. There are some rates in reduced bandwidth modes which can't be represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The standard suggests to round up to the next multiple of 500kbps, just do that in mac80211 as well. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> [make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix] Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2013-07-16mac80211: fix ethtool stats for non-station interfacesJohannes Berg1-0/+2
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514, the station loop never initialises 'sinfo' and therefore adds up a stack values, leaking stack information (the number of times it adds values is easily obtained another way.) Fix this by initialising the sinfo for each station to add. Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
2013-06-24mac80211: allow self-protected frame tx without staThomas Pedersen1-1/+2
Useful for userspace mesh to authenticate and peer without a station entry, since both steps may fail anyway. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-19Merge remote-tracking branch 'mac80211/master' into HEADJohannes Berg1-0/+6
Merge mac80211 to avoid conflicts with the nl80211 attrbuf changes. Conflicts: net/mac80211/iface.c net/wireless/nl80211.c Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-18Revert "mac80211: in IBSS use the Auth frame to trigger STA reinsertion"Antonio Quartulli1-11/+0
This reverts commit 6d810f10325522cfcf498dc6d64b9f96e1f5153f In this way an IBSS station will not use the AUTH messages to trigger a state reinitialisation anymore. The behaviour was racy and was not working properly. It has been introduced to help wpa_supplicant to support IBSS/RSN, however all the logic is now getting moved into wpa_s itself which will also be in charge of handling the AUTH messages thanks to the mgmt frame registration. If userspace does not register for receiving AUTH frames then mac80211 will still reply by itself. At the same time, the auth frame registration counter can be removed since it is not needed anymore. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> [remove unused variable] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-12mac80211: abort CAC in stop_ap()Simon Wunderlich1-0/+6
When a CAC is running and stop_ap is called (e.g. when hostapd is killed while performing CAC), the CAC must be aborted immediately. Otherwise ieee80211_stop_ap() will try to stop it when it's too late - wdev->channel is already NULL and the abort event can not be generated. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-11mac80211: make mgmt_tx accept a NULL channelAntonio Quartulli1-3/+14
cfg80211 passes a NULL channel to mgmt_tx if the frame has to be sent on the one currently in use by the device. Make the implementation of mgmt_tx correctly handle this case. Fail if offchan is required. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> [fix RCU locking] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-11{nl,mac,cfg}80211: Allow user to configure basic rates for meshAshok Nagarajan1-0/+1
Currently mesh uses mandatory rates as the default basic rates. Allow basic rates to be configured during mesh join. Basic rates are applied only if channel is also provided with mesh join command. Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> [some whitespace fixes, refuse basic rates w/o channel] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-11mac80211: expire mesh peers based on mesh configurationColleen Twitty1-0/+2
The time it takes to see the peer link expire may differ by a minute since sta_expire() is run once a minute as a mesh housekeeping task. Signed-off-by: Colleen Twitty <colleen@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-03mac80211: fix sdata locking around __ieee80211_request_smpsJohannes Berg1-0/+2
My cfg80211/mac80211 locking unification broke the sdata locking in ieee80211_set_power_mgmt, it needs to acquire the lock for __ieee80211_request_smps(). Add the locking. Reported-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29mac80211: support active monitor interfacesFelix Fietkau1-4/+7
Support them only if the driver advertises support for them via IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces, they are added to the driver, along with their MAC address. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-25cfg80211/mac80211: use cfg80211 wdev mutex in mac80211Johannes Berg1-3/+1
Using separate locks in cfg80211 and mac80211 has always caused issues, for example having to unlock in places in mac80211 to call cfg80211, which even needed a framework to make cfg80211 calls after some functions returned etc. Additionally, I suspect some issues people have reported with the cfg80211 state getting confused could be due to such issues, when cfg80211 is asking mac80211 to change state but mac80211 is in the process of telling cfg80211 that the state changed (in another way.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-06 19:20:47 +0000