summaryrefslogtreecommitdiffstats
path: root/net/l3mdev
AgeCommit message (Collapse)AuthorFilesLines
2020-06-20l3mdev: add infrastructure for table to VRF mappingAndrea Mayer1-0/+93
Add infrastructure to l3mdev (the core code for Layer 3 master devices) in order to find out the corresponding VRF device for a given table id. Therefore, the l3mdev implementations: - can register a callback that returns the device index of the l3mdev associated with a given table id; - can offer the lookup function (table to VRF device). Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-14treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada1-1/+1
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2019-06-23ipv6: convert major tx path to use RT6_LOOKUP_F_DST_NOREFWei Wang1-4/+3
For tx path, in most cases, we still have to take refcnt on the dst cause the caller is caching the dst somewhere. But it still is beneficial to make use of RT6_LOOKUP_F_DST_NOREF flag while doing the route lookup. It is cause this flag prevents manipulating refcnt on net->ipv6.ip6_null_entry when doing fib6_rule_lookup() to traverse each routing table. The null_entry is a shared object and constant updates on it cause false sharing. We converted the current major lookup function ip6_route_output_flags() to make use of RT6_LOOKUP_F_DST_NOREF. Together with the change in the rx path, we see noticable performance boost: I ran synflood tests between 2 hosts under the same switch. Both hosts have 20G mlx NIC, and 8 tx/rx queues. Sender sends pure SYN flood with random src IPs and ports using trafgen. Receiver has a simple TCP listener on the target port. Both hosts have multiple custom rules: - For incoming packets, only local table is traversed. - For outgoing packets, 3 tables are traversed to find the route. The packet processing rate on the receiver is as follows: - Before the fix: 3.78Mpps - After the fix: 5.50Mpps Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner1-5/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner2-0/+2
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-03l3mdev: add function to retreive upper masterAlexis Bauvin1-0/+18
Existing functions to retreive the l3mdev of a device did not walk the master chain to find the upper master. This patch adds a function to find the l3mdev, even indirect through e.g. a bridge: +----------+ | | | vrf-blue | | | +----+-----+ | | +----+-----+ | | | br-blue | | | +----+-----+ | | +----+-----+ | | | eth0 | | | +----------+ This will properly resolve the l3mdev of eth0 to vrf-blue. Signed-off-by: Alexis Bauvin <abauvin@scaleway.com> Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: Amine Kherbouche <akherbouche@scaleway.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-10net: ipv6: Remove l3mdev_get_saddr6David Ahern1-24/+0
No longer needed Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-10net: ipv4: Remove l3mdev_get_saddrDavid Ahern1-31/+0
No longer needed Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-10net: vrf: Flip IPv6 output path from FIB lookup hook to out hookDavid Ahern1-8/+7
Flip the IPv6 output path to use the l3mdev tx out hook. The VRF dst is not returned on the first FIB lookup. Instead, the dst on the skb is switched at the beginning of the IPv6 output processing to send the packet to the VRF driver on xmit. Link scope addresses (linklocal and multicast) need special handling: specifically the oif the flow struct can not be changed because we want the lookup tied to the enslaved interface. ie., the source address and the returned route MUST point to the interface scope passed in. Convert the existing vrf_get_rt6_dst to handle only link scope addresses. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-10net: flow: Add l3mdev flow updateDavid Ahern1-0/+35
Add l3mdev hook to set FLOWI_FLAG_SKIP_NH_OIF flag and update oif/iif in flow struct if its oif or iif points to a device enslaved to an L3 Master device. Only 1 needs to be converted to match the l3mdev FIB rule. This moves the flow adjustment for l3mdev to a single point catching all lookups. It is redundant for existing hooks (those are removed in later patches) but is needed for missed lookups such as PMTU updates. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-17net: vrf: Implement get_saddr for IPv6David Ahern1-0/+24
IPv6 source address selection needs to consider the real egress route. Similar to IPv4 implement a get_saddr6 method which is called if source address has not been set. The get_saddr6 method does a full lookup which means pulling a route from the VRF FIB table and properly considering linklocal/multicast destination addresses. Lookup failures (eg., unreachable) then cause the source address selection to fail which gets propagated back to the caller. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-15net: l3mdev: Remove const from flowi6 arg to get_rt6_dstDavid Ahern1-1/+1
Allow drivers to pass flow arg to functions where the arg is not const and allow the driver to make updates as needed (eg., setting oif). Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-08net: Add l3mdev ruleDavid Ahern1-0/+38
Currently, VRFs require 1 oif and 1 iif rule per address family per VRF. As the number of VRF devices increases it brings scalability issues with the increasing rule list. All of the VRF rules have the same format with the exception of the specific table id to direct the lookup. Since the table id is available from the oif or iif in the loopup, the VRF rules can be consolidated to a single rule that pulls the table from the VRF device. This patch introduces a new rule attribute l3mdev. The l3mdev rule means the table id used for the lookup is pulled from the L3 master device (e.g., VRF) rather than being statically defined. With the l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev rule per address family (IPv4 and IPv6). If an admin wishes to insert higher priority rules for specific VRFs those rules will co-exist with the l3mdev rule. This capability means current VRF scripts will co-exist with this new simpler implementation. Currently, the rules list for both ipv4 and ipv6 look like this: $ ip ru ls 1000: from all oif vrf1 lookup 1001 1000: from all iif vrf1 lookup 1001 1000: from all oif vrf2 lookup 1002 1000: from all iif vrf2 lookup 1002 1000: from all oif vrf3 lookup 1003 1000: from all iif vrf3 lookup 1003 1000: from all oif vrf4 lookup 1004 1000: from all iif vrf4 lookup 1004 1000: from all oif vrf5 lookup 1005 1000: from all iif vrf5 lookup 1005 1000: from all oif vrf6 lookup 1006 1000: from all iif vrf6 lookup 1006 1000: from all oif vrf7 lookup 1007 1000: from all iif vrf7 lookup 1007 1000: from all oif vrf8 lookup 1008 1000: from all iif vrf8 lookup 1008 ... 32765: from all lookup local 32766: from all lookup main 32767: from all lookup default With the l3mdev rule the list is just the following regardless of the number of VRFs: $ ip ru ls 1000: from all lookup [l3mdev table] 32765: from all lookup local 32766: from all lookup main 32767: from all lookup default (Note: the above pretty print of the rule is based on an iproute2 prototype. Actual verbage may change) Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-09net: l3mdev: Allow send on enslaved interfaceDavid Ahern1-4/+13
Allow udp and raw sockets to send by oif that is an enslaved interface versus the l3mdev/VRF device. For example, this allows BFD to use ifindex from IP_PKTINFO on a receive to send a response without the need to convert to the VRF index. It also allows ping and ping6 to work when specifying an enslaved interface (e.g., ping -I swp1 <ip>) which is a natural use case. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-09net: l3mdev: Move get_saddr and rt6_dstDavid Ahern1-0/+54
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only user and keep the l3mdev_get_rt6_dst name for consistency with other hooks. A follow-on patch adds more code to these functions making them long for inlined functions. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-26net: l3mdev: address selection should only consider devices in L3 domainDavid Ahern1-2/+9
David Lamparter noted a use case where the source address selection fails to pick an address from a VRF interface - unnumbered interfaces. Relevant commands from his script: ip addr add 9.9.9.9/32 dev lo ip link set lo up ip link add name vrf0 type vrf table 101 ip rule add oif vrf0 table 101 ip rule add iif vrf0 table 101 ip link set vrf0 up ip addr add 10.0.0.3/32 dev vrf0 ip link add name dummy2 type dummy ip link set dummy2 master vrf0 up --> note dummy2 has no address - unnumbered device ip route add 10.2.2.2/32 dev dummy2 table 101 ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02 tcpdump -ni dummy2 & And using ping instead of his socat example: $ ping -I vrf0 -c1 10.2.2.2 ping: Warning: source address might be selected on device other than vrf0. PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data. >From tcpdump: 12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64 Note the source address is from lo and is not a VRF local address. With this patch: $ ping -I vrf0 -c1 10.2.2.2 PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data. >From tcpdump: 12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64 Now the source address comes from vrf0. The ipv4 function for selecting source address takes a const argument. Removing the const requires touching a lot of places, so instead l3mdev_master_ifindex_rcu is changed to take a const argument and then do the typecast to non-const as required by netdev_master_upper_dev_get_rcu. This is similar to what l3mdev_fib_table_rcu does. IPv6 for unnumbered interfaces appears to be selecting the addresses properly. Cc: David Lamparter <david@opensourcerouting.org> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-07net: Add netif_is_l3_slaveDavid Ahern1-4/+4
IPv6 addrconf keys off of IFF_SLAVE so can not use it for L3 slave. Add a new private flag and add netif_is_l3_slave function for checking it. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-29net: Introduce L3 Master device abstractionDavid Ahern3-0/+107
L3 master devices allow users of the abstraction to influence FIB lookups for enslaved devices. Current API provides a means for the master device to return a specific FIB table for an enslaved device, to return an rtable/custom dst and influence the OIF used for fib lookups. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>