| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The commit 60fb9567bf30 ("udp: implement complete book-keeping for
encap_needed") introduced a severe misuse of jump label APIs, which
syzbot, as reported by Eric, was able to exploit.
When multiple sockets/process can concurrently request (and than
disable) the udp encap, we need to track the activation counter with
*_inc()/*_dec() jump label variants, or we can experience bad things
at disable time.
Fixes: 60fb9567bf30 ("udp: implement complete book-keeping for encap_needed")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the udp6 code path, we needed multiple tests to select the correct
mib to be updated. Since we touch at least a counter at each iteration,
it's convenient to use the recently introduced __UDPX_MIB() helper once
and remove some code duplication.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the destination port in FoU and GUE receiving sockets doesn't
necessarily match the remote destination port, we can't associate errors
to the encapsulating tunnels with a socket lookup -- we need to blindly
try them instead. This means we don't even know if we are handling errors
for FoU or GUE without digging into the packets.
Hence, implement a single handler for both, one for IPv4 and one for IPv6,
that will check whether the packet that generated the ICMP error used a
direct IP encapsulation or if it had a GUE header, and send the error to
the matching protocol handler, if any.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ICMP error handling is currently not possible for UDP tunnels not
employing a receiving socket with local destination port matching the
remote one, because we have no way to look them up.
Add an err_handler tunnel encapsulation operation that can be exported by
tunnels in order to pass the error to the protocol implementing the
encapsulation. We can't easily use a lookup function as we did for VXLAN
and GENEVE, as protocol error handlers, which would be in turn called by
implementations of this new operation, handle the errors themselves,
together with the tunnel lookup.
Without a socket, we can't be sure which encapsulation error handler is
the appropriate one: encapsulation handlers (the ones for FoU and GUE
introduced in the next patch, e.g.) will need to check the new error codes
returned by protocol handlers to figure out if errors match the given
encapsulation, and, in turn, report this error back, so that we can try
all of them in __udp{4,6}_lib_err_encap_no_sk() until we have a match.
v2:
- Name all arguments in err_handler prototypes (David Miller)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We'll need this to handle ICMP errors for tunnels without a sending socket
(i.e. FoU and GUE). There, we might have to look up different types of IP
tunnels, registered as network protocols, before we get a match, so we
want this for the error handlers of IPPROTO_IPIP and IPPROTO_IPV6 in both
inet_protos and inet6_protos. These error codes will be used in the next
patch.
For consistency, return sensible error codes in protocol error handlers
whenever handlers can't handle errors because, even if valid, they don't
match a protocol or any of its states.
This has no effect on existing error handling paths.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For both IPv4 and IPv6, if we can't match errors to a socket, try
tunnels before ignoring them. Look up a socket with the original source
and destination ports as found in the UDP packet inside the ICMP payload,
this will work for tunnels that force the same destination port for both
endpoints, i.e. VXLAN and GENEVE.
Actually, lwtunnels could break this assumption if they are configured by
an external control plane to have different destination ports on the
endpoints: in this case, we won't be able to trace ICMP messages back to
them.
For IPv6 redirect messages, call ip6_redirect() directly with the output
interface argument set to the interface we received the packet from (as
it's the very interface we should build the exception on), otherwise the
new nexthop will be rejected. There's no such need for IPv4.
Tunnels can now export an encap_err_lookup() operation that indicates a
match. Pass the packet to the lookup function, and if the tunnel driver
reports a matching association, continue with regular ICMP error handling.
v2:
- Added newline between network and transport header sets in
__udp{4,6}_lib_err_encap() (David Miller)
- Removed redundant skb_reset_network_header(skb); in
__udp4_lib_err_encap()
- Removed redundant reassignment of iph in __udp4_lib_err_encap()
(Sabrina Dubroca)
- Edited comment to __udp{4,6}_lib_err_encap() to reflect the fact this
won't work with lwtunnels configured to use asymmetric ports. By the way,
it's VXLAN, not VxLAN (Jiri Benc)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
avoid to compute the hash value if dev is not null, since
hash value is not used
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some scenarios, the GRO engine can assemble an UDP GRO packet
that ultimately lands on a non GRO-enabled socket.
This patch tries to address the issue explicitly checking for the UDP
socket features before enqueuing the packet, and eventually segmenting
the unexpected GRO packet, as needed.
We must also cope with re-insertion requests: after segmentation the
UDP code calls the helper introduced by the previous patches, as needed.
Segmentation is performed by a common helper, which takes care of
updating socket and protocol stats is case of failure.
rfc v3 -> v1
- fix compile issues with rxrpc
- when gso_segment returns NULL, treat is as an error
- added 'ipv4' argument to udp_rcv_segment()
rfc v2 -> rfc v3
- moved udp_rcv_segment() into net/udp.h, account errors to socket
and ns, always return NULL or segs list
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So that we can re-use it at the UDP level in the next patch
rfc v3 -> v1:
- add the helper declaration into the ipv6 header
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When UDP GRO is enabled, the UDP_GRO cmsg will carry the ingress
datagram size. User-space can use such info to compute the original
packets layout.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the RX counterpart of commit bec1f6f69736 ("udp: generate gso
with UDP_SEGMENT"). When UDP_GRO is enabled, such socket is also
eligible for GRO in the rx path: UDP segments directed to such socket
are assembled into a larger GSO_UDP_L4 packet.
The core UDP GRO support is enabled with setsockopt(UDP_GRO).
Initial benchmark numbers:
Before:
udp rx: 1079 MB/s 769065 calls/s
After:
udp rx: 1466 MB/s 24877 calls/s
This change introduces a side effect in respect to UDP tunnels:
after a UDP tunnel creation, now the kernel performs a lookup per ingress
UDP packet, while before such lookup happened only if the ingress packet
carried a valid internal header csum.
rfc v2 -> rfc v3:
- fixed typos in macro name and comments
- really enforce UDP_GRO_CNT_MAX, instead of UDP_GRO_CNT_MAX + 1
- acquire socket lock in UDP_GRO setsockopt
rfc v1 -> rfc v2:
- use a new option to enable UDP GRO
- use static keys to protect the UDP GRO socket lookup
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The *encap_needed static keys are enabled by UDP tunnels
and several UDP encapsulations type, but they are never
turned off. This can cause unneeded overall performance
degradation for systems where such features are used
transiently.
This patch introduces complete book-keeping for such keys,
decreasing the usage at socket destruction time, if needed,
and avoiding that the same socket could increase the key
usage multiple times.
rfc v3 -> v1:
- add socket lock around udp_tunnel_encap_enable()
rfc v2 -> rfc v3:
- use udp_tunnel_encap_enable() in setsockopt()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For bound udp sockets in a vrf, also check the sdif to get the index
for ingress devices enslaved to an l3mdev.
Signed-off-by: Dewi Morgan <morgand@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the skb for multicast packets marked as enslaved to a VRF are
received, then the secondary device index should be used to obtain
the real device. And verify the multicast address against the
enslaved rather than the l3mdev device.
Signed-off-by: Dewi Morgan <morgand@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If link-local packets are marked as enslaved to a VRF, then to allow
ping to the link-local from a vrf, the error handling for IPV6_PKTINFO
needs to be relaxed to also allow the pkt ipi6_ifindex to be that of a
slave device to the vrf.
Note that the real device also needs to be retrieved in icmp6_iif()
to set the ipv6 flow oif to this for icmp echo reply handling. The
recent commit 24b711edfc34 ("net/ipv6: Fix linklocal to global address
with VRF") takes care of this, so the sdif does not need checking here.
This fix makes ping to link-local consistent with that to global
addresses, in that this can now be done from within the same VRF that
the address is in.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there exist a pair of raw sockets one unbound and one bound
to a VRF but equal in all other respects, when a packet is received
in the VRF context, __raw_v4_lookup() matches on both sockets.
This results in the packet being delivered over both sockets,
instead of only the raw socket bound to the VRF. The bound device
checks in __raw_v4_lookup() are replaced with a call to
raw_sk_bound_dev_eq() which correctly handles whether the packet
should be delivered over the unbound socket in such cases.
In __raw_v6_lookup() the match on the device binding of the socket is
similarly updated to use raw_sk_bound_dev_eq() which matches the
handling in __raw_v4_lookup().
Importantly raw_sk_bound_dev_eq() takes the raw_l3mdev_accept sysctl
into account.
Signed-off-by: Duncan Eastoe <deastoe@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure an unbound datagram skt is chosen when not in a VRF. The check
for a device match in compute_score() for UDP must be performed when
there is no device match. For this, a failure is returned when there is
no device match. This ensures that bound sockets are never selected,
even if there is no unbound socket.
Allow IPv6 packets to be sent over a datagram skt bound to a VRF. These
packets are currently blocked, as flowi6_oif was set to that of the
master vrf device, and the ipi6_ifindex is that of the slave device.
Allow these packets to be sent by checking the device with ipi6_ifindex
has the same L3 scope as that of the bound device of the skt, which is
the master vrf device. Note that this check always succeeds if the skt
is unbound.
Even though the right datagram skt is now selected by compute_score(),
a different skt is being returned that is bound to the wrong vrf. The
difference between these and stream sockets is the handling of the skt
option for SO_REUSEPORT. While the handling when adding a skt for reuse
correctly checks that the bound device of the skt is a match, the skts
in the hashslot are already incorrect. So for the same hash, a skt for
the wrong vrf may be selected for the required port. The root cause is
that the skt is immediately placed into a slot when it is created,
but when the skt is then bound using SO_BINDTODEVICE, it remains in the
same slot. The solution is to move the skt to the correct slot by
forcing a rehash.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit a04a480d4392 ("net: Require exact match for TCP socket
lookups if dif is l3mdev") only ensures that the correct socket is
selected for packets in a VRF. However, there is no guarantee that
the unbound socket will be selected for packets when not in a VRF.
By checking for a device match in compute_score() also for the case
when there is no bound device and attaching a score to this, the
unbound socket is selected. And if a failure is returned when there
is no device match, this ensures that bound sockets are never selected,
even if there is no unbound socket.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add extack argument to ip_fib_metrics_init and add messages for invalid
metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_gro_receive() compares 34 bytes using slow memcmp(),
while handcoding with a couple of ipv6_addr_equal() is much faster.
Before this patch, "perf top -e cycles:pp -C <cpu>" would
see memcmp() using ~10% of cpu cycles on a 40Gbit NIC
receiving IPv6 TCP traffic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains the first batch of Netfilter fixes for
your net tree:
1) Fix splat with IPv6 defragmenting locally generated fragments,
from Florian Westphal.
2) Fix Incorrect check for missing attribute in nft_osf.
3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
header, from Jiri Slaby.
4) Revert map lookup in nft_numgen, this is already possible with
the existing infrastructure without this extension.
5) Fix wrong listing of set reference counter, make counter
synchronous again, from Stefano Brivio.
6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.
7) Fix allocation failure with large set, use kvcalloc().
From Andrey Ryabinin.
8) No need to disable BH when fetch ip set comment, patch from
Jozsef Kadlecsik.
9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
Taehee Yoo.
10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
from Jozsef Kadlecsik.
11) Fix setting default timeout via nfnetlink_cttimeout, this
comes with preparation patch to add nf_{tcp,udp,...}_pernet()
helper.
12) Allow ebtables table nat to be of filter type via nft_compat.
From Florian Westphal.
13) Incorrect calculation of next bucket in early_drop, do no bump
hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.
Fixes: 08e814c9e8eb ("net/ipv6: Bail early if user only wants cloned entries")
Fixes: ae677bbb4441 ("net: Don't return invalid table id error when dumping all families")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.
Fixes: 2384d02520ff ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
icmp6_send() function is expensive on systems with a large number of
interfaces. Every time it’s called, it has to verify that the source
address does not correspond to an existing anycast address by looping
through every device and every anycast address on the device. This can
result in significant delays for a CPU when there are a large number of
neighbors and ND timers are frequently timing out and calling
neigh_invalidate().
Add anycast addresses to a global hashtable to allow quick searching for
matching anycast addresses. This is based on inet6_addr_lst in addrconf.c.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Traceroute executed in a vrf succeeds if no device is given or if the
vrf is given as the device, but fails if the interface is given as the
device. This is for default UDP probes, it succeeds for TCP SYN or ICMP
ECHO probes. As the skb bound dev is the interface and the sk dev is
the vrf, sk lookup fails for ICMP_DEST_UNREACH and ICMP_TIME_EXCEEDED
messages. The solution is for the secondary dev to be passed so that
the interface is available for the device match to succeed, in the same
way as is already done for non-error cases.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a61bbcf28a8c ("[NET]: Store skb->timestamp as offset to a base
timestamp") introduces a neighbour control buffer and zeroes it out in
ndisc_rcv(), as ndisc_recv_ns() uses it.
Commit f2776ff04722 ("[IPV6]: Fix address/interface handling in UDP and
DCCP, according to the scoping architecture.") introduces the usage of the
IPv6 control buffer in protocol error handlers (e.g. inet6_iif() in
present-day __udp6_lib_err()).
Now, with commit b94f1c0904da ("ipv6: Use icmpv6_notify() to propagate
redirect, instead of rt6_redirect()."), we call protocol error handlers
from ndisc_redirect_rcv(), after the control buffer is already stolen and
some parts are already zeroed out. This implies that inet6_iif() on this
path will always return zero.
This gives unexpected results on UDP socket lookup in __udp6_lib_err(), as
we might actually need to match sockets for a given interface.
Instead of always claiming the control buffer in ndisc_rcv(), do that only
when needed.
Fixes: b94f1c0904da ("ipv6: Use icmpv6_notify() to propagate redirect, instead of rt6_redirect().")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cleanup path will put the target net when netnsid is set. So we must
reset netnsid if the input is invalid.
Fixes: d7e38611b81e ("net/ipv4: Put target net when address dump fails due to bad attributes")
Fixes: 242afaa6968c ("net/ipv6: Put target net when address dump fails due to bad attributes")
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike ipv4 and normal ipv6 defrag, netfilter ipv6 defragmentation did
not save/restore skb->dst.
This causes oops when handling locally generated ipv6 fragments, as
output path needs a valid dst.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Fixes: 84379c9afe01 ("netfilter: ipv6: nf_defrag: drop skb dst before queueing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
route
The intent of ip6_route_check_nh_onlink is to make sure the gateway
given for an onlink route is not actually on a connected route for
a different interface (e.g., 2001:db8:1::/64 is on dev eth1 and then
an onlink route has a via 2001:db8:1::1 dev eth2). If the gateway
lookup hits the default route then it most likely will be a different
interface than the onlink route which is ok.
Update ip6_route_check_nh_onlink to disregard the device mismatch
if the gateway lookup hits the default route. Turns out the existing
onlink tests are passing because there is no default route or it is
an unreachable default, so update the onlink tests to have a default
route other than unreachable.
Fixes: fc1e64e1092f6 ("net/ipv6: Add support for onlink flag")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057ca ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing a route dump across all address families, do not error out
if the table does not exist. This allows a route dump for AF_UNSPEC
with a table id that may only exist for some of the families.
Do return the table does not exist error if dumping routes for a
specific family and the table does not exist.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If tgt_net is set based on IFA_TARGET_NETNSID attribute in the dump
request, make sure all error paths call put_net.
Fixes: 6371a71f3a3b ("net/ipv6: Add support for dumping addresses for a specific device")
Fixes: ed6eff11790a ("net/ipv6: Update inet6_dump_addr for strict data checking")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an RTM_GETADDR dump request has ifa_index set in the ifaddrmsg
header, then return only the addresses for that device.
Since inet6_dump_addr is reused for multicast and anycast addresses,
this adds support for device specfic dumps of RTM_GETMULTICAST and
RTM_GETANYCAST as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_idx is always 0 going into in6_dump_addrs; it is passed as a pointer
to save the last good index into cb. Since cb is already argument to
in6_dump_addrs, just save the value there.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Ahern's dump indexing bug fix in 'net' overlapped the
change of the function signature of inet6_fill_ifaddr() in
'net-next'. Trivially resolved.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd7376a ("ipv6: convert idev_list to list macros")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 058214a4d1df ("ip6_tun: Add infrastructure for doing
encapsulation") added the ip6_tnl_encap() call in ip6_tnl_xmit(), before
the call to ipv6_push_frag_opts() to append the IPv6 Tunnel Encapsulation
Limit option (option 4, RFC 2473, par. 5.1) to the outer IPv6 header.
As long as the option didn't actually end up in generated packets, this
wasn't an issue. Then commit 89a23c8b528b ("ip6_tunnel: Fix missing tunnel
encapsulation limit option") fixed sending of this option, and the
resulting layout, e.g. for FoU, is:
.-------------------.------------.----------.-------------------.----- - -
| Outer IPv6 Header | UDP header | Option 4 | Inner IPv6 Header | Payload
'-------------------'------------'----------'-------------------'----- - -
Needless to say, FoU and GUE (at least) won't work over IPv6. The option
is appended by default, and I couldn't find a way to disable it with the
current iproute2.
Turn this into a more reasonable:
.-------------------.----------.------------.-------------------.----- - -
| Outer IPv6 Header | Option 4 | UDP header | Inner IPv6 Header | Payload
'-------------------'----------'------------'-------------------'----- - -
With this, and with 84dad55951b0 ("udp6: fix encap return code for
resubmitting"), FoU and GUE work again over IPv6.
Fixes: 058214a4d1df ("ip6_tun: Add infrastructure for doing encapsulation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2018-10-18
1) Free the xfrm interface gro_cells when deleting the
interface, otherwise we leak it. From Li RongQing.
2) net/core/flow.c does not exist anymore, so remove it
from the MAINTAINERS file.
3) Fix a slab-out-of-bounds in _decode_session6.
From Alexei Starovoitov.
4) Fix RCU protection when policies inserted into
thei bydst lists. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit eb63f2964dbe ("udp6: add missing checks on edumux packet
processing") used the same return code convention of the ipv4 counterpart,
but ipv6 uses the opposite one: positive values means resubmit.
This change addresses the issue, using positive return value for
resubmitting. Also update the related comment, which was broken, too.
Fixes: eb63f2964dbe ("udp6: add missing checks on edumux packet processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to IPv4, IPv6 fib no longer contains cloned routes. If a user
requests a route dump for only cloned entries, no sense walking the FIB
and returning everything.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update parsing of route dump request to enable kernel side filtering.
Allow filtering results by protocol (e.g., which routing daemon installed
the route), route type (e.g., unicast), table id and nexthop device. These
amount to the low hanging fruit, yet a huge improvement, for dumping
routes.
ip_valid_fib_dump_req is called with RTNL held, so __dev_get_by_index can
be used to look up the device index without taking a reference. From
there filter->dev is only used during dump loops with the lock still held.
Set NLM_F_DUMP_FILTERED in the answer_flags so the user knows the results
have been filtered should no entries be returned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement kernel side filtering of routes by egress device index and
table id. If the table id is given in the filter, lookup table and
call mr_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement kernel side filtering of routes by table id, egress device
index, protocol, and route type. If the table id is given in the filter,
lookup the table and call fib6_dump_table directly for it.
Move the existing route flags check for prefix only routes to the new
filter.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add struct fib_dump_filter for options on limiting which routes are
returned in a dump request. The current list is table id, protocol,
route type, rtm_flags and nexthop device index. struct net is needed
to lookup the net_device from the index.
Declare the filter for each route dump handler and plumb the new
arguments from dump handlers to ip_valid_fib_dump_req.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot found a use-after-free in inet6_mc_check [1]
The problem here is that inet6_mc_check() uses rcu
and read_lock(&iml->sflock)
So the fact that ip6_mc_leave_src() is called under RTNL
and the socket lock does not help us, we need to acquire
iml->sflock in write mode.
In the future, we should convert all this stuff to RCU.
[1]
BUG: KASAN: use-after-free in ipv6_addr_equal include/net/ipv6.h:521 [inline]
BUG: KASAN: use-after-free in inet6_mc_check+0xae7/0xb40 net/ipv6/mcast.c:649
Read of size 8 at addr ffff8801ce7f2510 by task syz-executor0/22432
CPU: 1 PID: 22432 Comm: syz-executor0 Not tainted 4.19.0-rc7+ #280
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c4/0x2b4 lib/dump_stack.c:113
print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
ipv6_addr_equal include/net/ipv6.h:521 [inline]
inet6_mc_check+0xae7/0xb40 net/ipv6/mcast.c:649
__raw_v6_lookup+0x320/0x3f0 net/ipv6/raw.c:98
ipv6_raw_deliver net/ipv6/raw.c:183 [inline]
raw6_local_deliver+0x3d3/0xcb0 net/ipv6/raw.c:240
ip6_input_finish+0x467/0x1aa0 net/ipv6/ip6_input.c:345
NF_HOOK include/linux/netfilter.h:289 [inline]
ip6_input+0xe9/0x600 net/ipv6/ip6_input.c:426
ip6_mc_input+0x48a/0xd20 net/ipv6/ip6_input.c:503
dst_input include/net/dst.h:450 [inline]
ip6_rcv_finish+0x17a/0x330 net/ipv6/ip6_input.c:76
NF_HOOK include/linux/netfilter.h:289 [inline]
ipv6_rcv+0x120/0x640 net/ipv6/ip6_input.c:271
__netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4913
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5023
netif_receive_skb_internal+0x12c/0x620 net/core/dev.c:5126
napi_frags_finish net/core/dev.c:5664 [inline]
napi_gro_frags+0x75a/0xc90 net/core/dev.c:5737
tun_get_user+0x3189/0x4250 drivers/net/tun.c:1923
tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:1968
call_write_iter include/linux/fs.h:1808 [inline]
do_iter_readv_writev+0x8b0/0xa80 fs/read_write.c:680
do_iter_write+0x185/0x5f0 fs/read_write.c:959
vfs_writev+0x1f1/0x360 fs/read_write.c:1004
do_writev+0x11a/0x310 fs/read_write.c:1039
__do_sys_writev fs/read_write.c:1112 [inline]
__se_sys_writev fs/read_write.c:1109 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1109
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457421
Code: 75 14 b8 14 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 34 b5 fb ff c3 48 83 ec 08 e8 1a 2d 00 00 48 89 04 24 b8 14 00 00 00 0f 05 <48> 8b 3c 24 48 89 c2 e8 63 2d 00 00 48 89 d0 48 83 c4 08 48 3d 01
RSP: 002b:00007f2d30ecaba0 EFLAGS: 00000293 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 000000000000003e RCX: 0000000000457421
RDX: 0000000000000001 RSI: 00007f2d30ecabf0 RDI: 00000000000000f0
RBP: 0000000020000500 R08: 00000000000000f0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000293 R12: 00007f2d30ecb6d4
R13: 00000000004c4890 R14: 00000000004d7b90 R15: 00000000ffffffff
Allocated by task 22437:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
__do_kmalloc mm/slab.c:3718 [inline]
__kmalloc+0x14e/0x760 mm/slab.c:3727
kmalloc include/linux/slab.h:518 [inline]
sock_kmalloc+0x15a/0x1f0 net/core/sock.c:1983
ip6_mc_source+0x14dd/0x1960 net/ipv6/mcast.c:427
do_ipv6_setsockopt.isra.9+0x3afb/0x45d0 net/ipv6/ipv6_sockglue.c:743
ipv6_setsockopt+0xbd/0x170 net/ipv6/ipv6_sockglue.c:933
rawv6_setsockopt+0x59/0x140 net/ipv6/raw.c:1069
sock_common_setsockopt+0x9a/0xe0 net/core/sock.c:3038
__sys_setsockopt+0x1ba/0x3c0 net/socket.c:1902
__do_sys_setsockopt net/socket.c:1913 [inline]
__se_sys_setsockopt net/socket.c:1910 [inline]
__x64_sys_setsockopt+0xbe/0x150 net/socket.c:1910
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 22430:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3813
__sock_kfree_s net/core/sock.c:2004 [inline]
sock_kfree_s+0x29/0x60 net/core/sock.c:2010
ip6_mc_leave_src+0x11a/0x1d0 net/ipv6/mcast.c:2448
__ipv6_sock_mc_close+0x20b/0x4e0 net/ipv6/mcast.c:310
ipv6_sock_mc_close+0x158/0x1d0 net/ipv6/mcast.c:328
inet6_release+0x40/0x70 net/ipv6/af_inet6.c:452
__sock_release+0xd7/0x250 net/socket.c:579
sock_close+0x19/0x20 net/socket.c:1141
__fput+0x385/0xa30 fs/file_table.c:278
____fput+0x15/0x20 fs/file_table.c:309
task_work_run+0x1e8/0x2a0 kernel/task_work.c:113
tracehook_notify_resume include/linux/tracehook.h:193 [inline]
exit_to_usermode_loop+0x318/0x380 arch/x86/entry/common.c:166
prepare_exit_to_usermode arch/x86/entry/common.c:197 [inline]
syscall_return_slowpath arch/x86/entry/common.c:268 [inline]
do_syscall_64+0x6be/0x820 arch/x86/entry/common.c:293
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8801ce7f2500
which belongs to the cache kmalloc-192 of size 192
The buggy address is located 16 bytes inside of
192-byte region [ffff8801ce7f2500, ffff8801ce7f25c0)
The buggy address belongs to the page:
page:ffffea000739fc80 count:1 mapcount:0 mapping:ffff8801da800040 index:0x0
flags: 0x2fffc0000000100(slab)
raw: 02fffc0000000100 ffffea0006f6e548 ffffea000737b948 ffff8801da800040
raw: 0000000000000000 ffff8801ce7f2000 0000000100000010 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801ce7f2400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801ce7f2480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8801ce7f2500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8801ce7f2580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff8801ce7f2600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit 270972554c91 ("[IPV6]: ROUTE: Add Router Reachability
Probing (RFC4191).") introduced router probing, the rt6_probe() function
required that a neighbour entry existed. This neighbour entry is used to
record the timestamp of the last probe via the ->updated field.
Later, commit 2152caea7196 ("ipv6: Do not depend on rt->n in rt6_probe().")
removed the requirement for a neighbour entry. Neighbourless routes skip
the interval check and are not rate-limited.
This patch adds rate-limiting for neighbourless routes, by recording the
timestamp of the last probe in the fib6_info itself.
Fixes: 2152caea7196 ("ipv6: Do not depend on rt->n in rt6_probe().")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a more complete fix than d71019b54bff ("net: core: Fix build
with CONFIG_IPV6=m"), so that IPv6 sockets may be looked up if the IPv6
module is loaded (not just if it's compiled in).
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
