summaryrefslogtreecommitdiffstats
path: root/net/ipv6
AgeCommit message (Collapse)AuthorFilesLines
2012-02-01ipv6: Remove never used function inet6_ac_check().David S. Miller1-29/+0
It went from unused, to commented out, and never changing after that. Just get rid of it, if someone wants it they can unearth it from the history. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-01tcp: md5: RST: getting md5 key from listenerShawn Lu1-2/+41
TCP RST mechanism is broken in TCP md5(RFC2385). When connection is gone, md5 key is lost, sending RST without md5 hash is deem to ignored by peer. This can be a problem since RST help protocal like bgp to fast recove from peer crash. In most case, users of tcp md5, such as bgp and ldp, have listener on both sides to accept connection from peer. md5 keys for peers are saved in listening socket. There are two cases in finding md5 key when connection is lost: 1.Passive receive RST: The message is send to well known port, tcp will associate it with listner. md5 key is gotten from listener. 2.Active receive RST (no sock): The message is send to ative side, there is no socket associated with the message. In this case, finding listener from source port, then find md5 key from listener. we are not loosing sercuriy here: packet is checked with md5 hash. No RST is generated if md5 hash doesn't match or no md5 key can be found. Signed-off-by: Shawn Lu <shawn.lu@ericsson.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-01xfrm6: remove unneeded NULL check in __xfrm6_output()Dan Carpenter1-1/+1
We don't check for NULL consistently in __xfrm6_output(). If "x" were NULL here it would lead to an OOPs later. I asked Steffen Klassert about this and he suggested that we remove the NULL check. On 10/29/11, Steffen Klassert <steffen.klassert@secunet.com> wrote: >> net/ipv6/xfrm6_output.c >> 148 >> 149 if ((x && x->props.mode == XFRM_MODE_TUNNEL) && >> ^ > > x can't be null here. It would be a bug if __xfrm6_output() is called > without a xfrm_state attached to the skb. I think we can just remove > this null check. Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-01tcp: md5: protects md5sig_info with RCUEric Dumazet1-2/+0
This patch makes sure we use appropriate memory barriers before publishing tp->md5sig_info, allowing tcp_md5_do_lookup() being used from tcp_v4_send_reset() without holding socket lock (upcoming patch from Shawn Lu) Note we also need to respect rcu grace period before its freeing, since we can free socket without this grace period thanks to SLAB_DESTROY_BY_RCU Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Shawn Lu <shawn.lu@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31tcp: md5: rcu conversionEric Dumazet1-161/+12
In order to be able to support proper RST messages for TCP MD5 flows, we need to allow access to MD5 keys without locking listener socket. This conversion is a nice cleanup, and shrinks size of timewait sockets by 80 bytes. IPv6 code reuses generic code found in IPv4 instead of duplicating it. Control path uses GFP_KERNEL allocations instead of GFP_ATOMIC. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Shawn Lu <shawn.lu@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31tcp: md5: remove obsolete md5_add() methodEric Dumazet1-9/+0
We no longer use md5_add() method from struct tcp_sock_af_ops Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-30ipv6: fix RFC5722 commentEric Dumazet1-4/+3
RFC5722 Section 4 was amended by Errata 3089 Our implementation did the right thing anyway... Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-27ipv6: Eliminate dst_get_neighbour_noref() usage in ip6_forward().David S. Miller1-5/+3
It's only used to get at neigh->primary_key, which in this context is always going to be the same as rt->rt6i_gateway. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-27ipv6: Remove neigh argument from ndisc_send_redirect()David S. Miller2-3/+11
Instead, compute it as-needed inside of that function using dst_neigh_lookup(). Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-27ipv6: fib: Convert fib6_age() to dst_neigh_lookup().David S. Miller1-5/+14
In this specific situation we know we are dealing with a gatewayed route and therefore rt6i_gateway is not going to be in6addr_any even in future interpretations. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-27ipv6: ndisc: Convert to dst_neigh_lookup()David S. Miller1-6/+12
Now all code paths grab a local reference to the neigh, so if neigh is not NULL we unconditionally release it at the end. The old logic would only release if we didn't have a non-NULL 'rt'. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26ipv6: Use ipv6_addr_any()David S. Miller1-2/+1
Suggested by YOSHIFUJI Hideaki. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26ipv6: sit: Convert to dst_neigh_lookup()David S. Miller1-5/+15
The only semantic difference is that we now hold a reference to the neighbour and thus have to release it. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26ipv4/ipv6: Prepare for new route gateway semantics.David S. Miller1-1/+15
In the future the ipv4/ipv6 route gateway will take on two types of values: 1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case the neighbour must be obtained using the destination address in ipv4/ipv6 header as the lookup key. 2) Everything else, the actual nexthop route address. So if the gateway is not inaddr-any we use it, otherwise we must use the packet's destination address. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22tcp: md5: using remote adress for md5 lookup in rst packetshawnlu1-1/+1
md5 key is added in socket through remote address. remote address should be used in finding md5 key when sending out reset packet. Signed-off-by: shawnlu <shawn.lu@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18net: race condition in ipv6 forwarding and disable_ipv6 parametersFrancesco Ruggeri1-21/+40
There is a race condition in addrconf_sysctl_forward() and addrconf_sysctl_disable(). These functions change idev->cnf.forwarding (resp. idev->cnf.disable_ipv6) and then try to grab the rtnl lock before performing any actions. If that fails they restore the original value and restart the syscall. This creates race conditions if ipv6 code tries to access these parameters, or if multiple instances try to do the same operation. As an example of the former, if __ipv6_ifa_notify() finds a 0 in idev->cnf.forwarding when invoked by addrconf_ifdown() it may not free anycast addresses, ultimately resulting in the net_device not being freed. This patch reads the user parameters into a temporary location and only writes the actual parameters when the rtnl lock is acquired. Tested in 2.6.38.8. Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds3-3/+4
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits) tg3: Fix single-vector MSI-X code openvswitch: Fix multipart datapath dumps. ipv6: fix per device IP snmp counters inetpeer: initialize ->redirect_genid in inet_getpeer() net: fix NULL-deref in WARN() in skb_gso_segment() net: WARN if skb_checksum_help() is called on skb requiring segmentation caif: Remove bad WARN_ON in caif_dev caif: Fix typo in Vendor/Product-ID for CAIF modems bnx2x: Disable AN KR work-around for BCM57810 bnx2x: Remove AutoGrEEEn for BCM84833 bnx2x: Remove 100Mb force speed for BCM84833 bnx2x: Fix PFC setting on BCM57840 bnx2x: Fix Super-Isolate mode for BCM84833 net: fix some sparse errors net: kill duplicate included header net: sh-eth: Fix build error by the value which is not defined net: Use device model to get driver name in skb_gso_segment() bridge: BH already disabled in br_fdb_cleanup() net: move sock_update_memcg outside of CONFIG_INET mwl8k: Fixing Sparse ENDIAN CHECK warning ...
2012-01-17ipv6: fix per device IP snmp countersEric Dumazet1-2/+2
In commit 4ce3c183fca (snmp: 64bit ipstats_mib for all arches), I forgot to change the /proc/net/dev_snmp6/xxx output for IP counters. percpu array is 64bit per counter but the folding still used the 'long' variant, and output garbage on 32bit arches. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17net: fix some sparse errorsEric Dumazet1-1/+1
make C=2 CF="-D__CHECK_ENDIAN__" M=net And fix flowi4_init_output() prototype for sport Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-14Merge branch 'for-linus' of git://selinuxproject.org/~jmorris/linux-securityLinus Torvalds1-1/+1
* 'for-linus' of git://selinuxproject.org/~jmorris/linux-security: capabilities: remove __cap_full_set definition security: remove the security_netlink_recv hook as it is equivalent to capable() ptrace: do not audit capability check when outputing /proc/pid/stat capabilities: remove task_ns_* functions capabitlies: ns_capable can use the cap helpers rather than lsm call capabilities: style only - move capable below ns_capable capabilites: introduce new has_ns_capabilities_noaudit capabilities: call has_ns_capability from has_capability capabilities: remove all _real_ interfaces capabilities: introduce security_capable_noaudit capabilities: reverse arguments to security_capable capabilities: remove the task from capable LSM hook entirely selinux: sparse fix: fix several warnings in the security server cod selinux: sparse fix: fix warnings in netlink code selinux: sparse fix: eliminate warnings for selinuxfs selinux: sparse fix: declare selinux_disable() in security.h selinux: sparse fix: move selinux_complete_init selinux: sparse fix: make selinux_secmark_refcount static SELinux: Fix RCU deref check warning in sel_netport_insert() Manually fix up a semantic mis-merge wrt security_netlink_recv(): - the interface was removed in commit fd7784615248 ("security: remove the security_netlink_recv hook as it is equivalent to capable()") - a new user of it appeared in commit a38f7907b926 ("crypto: Add userspace configuration API") causing no automatic merge conflict, but Eric Paris pointed out the issue.
2012-01-13ipv6: release idev when ip6_neigh_lookup failed in icmp6_dst_allocRongQing.Li1-0/+1
release idev when ip6_neigh_lookup failed in icmp6_dst_alloc Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-12net: reintroduce missing rcu_assign_pointer() callsEric Dumazet4-11/+11
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to RCU_INIT_POINTER) did a lot of incorrect changes, since it did a complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x, y). We miss needed barriers, even on x86, when y is not NULL. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-05security: remove the security_netlink_recv hook as it is equivalent to capable()Eric Paris1-1/+1
Once upon a time netlink was not sync and we had to get the effective capabilities from the skb that was being received. Today we instead get the capabilities from the current task. This has rendered the entire purpose of the hook moot as it is now functionally equivalent to the capable() call. Signed-off-by: Eric Paris <eparis@redhat.com>
2012-01-04ipv6/addrconf: speedup /proc/net/if_inet6 fillingMihai Maruseac1-15/+28
This ensures a linear behaviour when filling /proc/net/if_inet6 thus making ifconfig run really fast on IPv6 only addresses. In fact, with this patch and the IPv4 one sent a while ago, ifconfig will run in linear time regardless of address type. IPv4 related patch: f04565ddf52e401880f8ba51de0dff8ba51c99fd dev: use name hash for dev_seq_ops ... Some statistics (running ifconfig > /dev/null on a different setup): iface count / IPv6 no-patch time / IPv6 patched time / IPv4 time ---------------------------------------------------------------- 6250 | 0.23 s | 0.13 s | 0.11 s 12500 | 0.62 s | 0.28 s | 0.22 s 25000 | 2.91 s | 0.57 s | 0.46 s 50000 | 11.37 s | 1.21 s | 0.94 s 128000 | 86.78 s | 3.05 s | 2.54 s Signed-off-by: Mihai Maruseac <mmaruseac@ixiacom.com> Cc: Daniel Baluta <dbaluta@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-04ipv6: Check RA for sllao when configuring optimistic ipv6 address (v2)Neil Horman2-3/+5
Recently Dave noticed that a test we did in ipv6_add_addr to see if we next hop route for the interface we're adding an addres to was wrong (see commit 7ffbcecbeed91e5874e9a1cfc4c0cbb07dac3069). for one, it never triggers, and two, it was completely wrong to begin with. This test was meant to cover this section of RFC 4429: 3.3 Modifications to RFC 2462 Stateless Address Autoconfiguration * (modifies section 5.5) A host MAY choose to configure a new address as an Optimistic Address. A host that does not know the SLLAO of its router SHOULD NOT configure a new address as Optimistic. A router SHOULD NOT configure an Optimistic Address. This patch should bring us into proper compliance with the above clause. Since we only add a SLAAC address after we've received a RA which may or may not contain a source link layer address option, we can pass a pointer to that option to addrconf_prefix_rcv (which may be null if the option is not present), and only set the optimistic flag if the option was found in the RA. Change notes: (v2) modified the new parameter to addrconf_prefix_rcv to be a bool rather than a pointer to make its use more clear as per request from davem. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-30IPv6: Avoid taking write lock for /proc/net/ipv6_routeJosh Hunt2-1/+21
During some debugging I needed to look into how /proc/net/ipv6_route operated and in my digging I found its calling fib6_clean_all() which uses "write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I found this on 2.6.32, but reading the code I believe the same basic idea exists currently. Looking at the rtnetlink code they are only calling "read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize reading from proc isn't the recommended way of fetching the ipv6 route table; taking a write lock seems unnecessary and would probably cause network performance issues. To verify this I loaded up the ipv6 route table and then ran iperf in 3 cases: * doing nothing * reading ipv6 route table via proc (while :; do cat /proc/net/ipv6_route > /dev/null; done) * reading ipv6 route table via rtnetlink (while :; do ip -6 route show table all > /dev/null; done) * Load the ipv6 route table up with: * for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done * iperf commands: * client: iperf -i 1 -V -c <ipv6 addr> * server: iperf -V -s * iperf results - 3 runs each (in Mbits/sec) * nothing: client: 927,927,927 server: 927,927,927 * proc: client: 179,97,96,113 server: 142,112,133 * iproute: client: 928,927,928 server: 927,927,927 lock_stat shows taking the write lock is causing the slowdown. Using this info I decided to write a version of fib6_clean_all() which replaces write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With this new function I see the same results as with my rtnetlink iperf test. Signed-off-by: Josh Hunt <joshhunt00@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-29ipv6: Fix neigh lookup using NULL device.David S. Miller1-7/+10
In some of the rt6_bind_neighbour() call sites, it hasn't hooked up the rt->dst.dev pointer yet, so we'd deref a NULL pointer when obtaining dev->ifindex for the neighbour hash function computation. Just pass the netdevice explicitly in to fix this problem. Reported-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-29ipv6: Report TCP timetstamp info in cacheinfo just like ipv4 does.David S. Miller1-1/+10
I missed this while adding ipv6 support to inet_peer. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-28ipv6: Kill rt6i_dev and rt6i_expires defines.David S. Miller7-47/+47
It just obscures that the netdevice pointer and the expires value are implemented in the dst_entry sub-object of the ipv6 route. And it makes grepping for dst_entry member uses much harder too. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-28ipv6: Create fast inline ipv6 neigh lookup just like ipv4.David S. Miller1-19/+22
Also, create and use an rt6_bind_neighbour() in net/ipv6/route.c to consolidate some common logic. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-28ipv6: Use universal hash for NDISC.David S. Miller1-10/+3
In order to perform a proper universal hash on a vector of integers, we have to use different universal hashes on each vector element. Which means we need 4 different hash randoms for ipv6. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-28ipv6: Remove optimistic DAD flag test in ipv6_add_addr()David Miller1-10/+0
The route we have here is for the address being added to the interface, ie. for input packet processing. Therefore using that route to determine whether an output nexthop gateway is known and resolved doesn't make any sense. So, simply remove this test, it never triggered anyways. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-By: Neil Horman <nhorman@tuxdriver.com>
2011-12-26ipv6: Kill useless route tracing bits in net/ipv6/route.cDavid S. Miller1-20/+2
RDBG() wasn't even used, and the messages printed by RT6_DEBUG() were far from useful. Just get rid of all this stuff, we can replace it with something more suitable if we want. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-25Merge branch 'nf-next' of git://1984.lsi.us.es/net-nextDavid S. Miller4-0/+151
2011-12-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+1
Conflicts: net/bluetooth/l2cap_core.c Just two overlapping changes, one added an initialization of a local variable, and another change added a new local variable. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-22net: introduce DST_NOPEER dst flagEric Dumazet1-1/+1
Chris Boot reported crashes occurring in ipv6_select_ident(). [ 461.457562] RIP: 0010:[<ffffffff812dde61>] [<ffffffff812dde61>] ipv6_select_ident+0x31/0xa7 [ 461.578229] Call Trace: [ 461.580742] <IRQ> [ 461.582870] [<ffffffff812efa7f>] ? udp6_ufo_fragment+0x124/0x1a2 [ 461.589054] [<ffffffff812dbfe0>] ? ipv6_gso_segment+0xc0/0x155 [ 461.595140] [<ffffffff812700c6>] ? skb_gso_segment+0x208/0x28b [ 461.601198] [<ffffffffa03f236b>] ? ipv6_confirm+0x146/0x15e [nf_conntrack_ipv6] [ 461.608786] [<ffffffff81291c4d>] ? nf_iterate+0x41/0x77 [ 461.614227] [<ffffffff81271d64>] ? dev_hard_start_xmit+0x357/0x543 [ 461.620659] [<ffffffff81291cf6>] ? nf_hook_slow+0x73/0x111 [ 461.626440] [<ffffffffa0379745>] ? br_parse_ip_options+0x19a/0x19a [bridge] [ 461.633581] [<ffffffff812722ff>] ? dev_queue_xmit+0x3af/0x459 [ 461.639577] [<ffffffffa03747d2>] ? br_dev_queue_push_xmit+0x72/0x76 [bridge] [ 461.646887] [<ffffffffa03791e3>] ? br_nf_post_routing+0x17d/0x18f [bridge] [ 461.653997] [<ffffffff81291c4d>] ? nf_iterate+0x41/0x77 [ 461.659473] [<ffffffffa0374760>] ? br_flood+0xfa/0xfa [bridge] [ 461.665485] [<ffffffff81291cf6>] ? nf_hook_slow+0x73/0x111 [ 461.671234] [<ffffffffa0374760>] ? br_flood+0xfa/0xfa [bridge] [ 461.677299] [<ffffffffa0379215>] ? nf_bridge_update_protocol+0x20/0x20 [bridge] [ 461.684891] [<ffffffffa03bb0e5>] ? nf_ct_zone+0xa/0x17 [nf_conntrack] [ 461.691520] [<ffffffffa0374760>] ? br_flood+0xfa/0xfa [bridge] [ 461.697572] [<ffffffffa0374812>] ? NF_HOOK.constprop.8+0x3c/0x56 [bridge] [ 461.704616] [<ffffffffa0379031>] ? nf_bridge_push_encap_header+0x1c/0x26 [bridge] [ 461.712329] [<ffffffffa037929f>] ? br_nf_forward_finish+0x8a/0x95 [bridge] [ 461.719490] [<ffffffffa037900a>] ? nf_bridge_pull_encap_header+0x1c/0x27 [bridge] [ 461.727223] [<ffffffffa0379974>] ? br_nf_forward_ip+0x1c0/0x1d4 [bridge] [ 461.734292] [<ffffffff81291c4d>] ? nf_iterate+0x41/0x77 [ 461.739758] [<ffffffffa03748cc>] ? __br_deliver+0xa0/0xa0 [bridge] [ 461.746203] [<ffffffff81291cf6>] ? nf_hook_slow+0x73/0x111 [ 461.751950] [<ffffffffa03748cc>] ? __br_deliver+0xa0/0xa0 [bridge] [ 461.758378] [<ffffffffa037533a>] ? NF_HOOK.constprop.4+0x56/0x56 [bridge] This is caused by bridge netfilter special dst_entry (fake_rtable), a special shared entry, where attaching an inetpeer makes no sense. Problem is present since commit 87c48fa3b46 (ipv6: make fragment identifications less predictable) Introduce DST_NOPEER dst flag and make sure ipv6_select_ident() and __ip_select_ident() fallback to the 'no peer attached' handling. Reported-by: Chris Boot <bootc@bootc.net> Tested-by: Chris Boot <bootc@bootc.net> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-19module_param: make bool parameters really bool (net & drivers/net)Rusty Russell1-1/+1
module_param(bool) used to counter-intuitively take an int. In fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy trick. It's time to remove the int/unsigned int option. For this version it'll simply give a warning, but it'll break next kernel version. (Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false). Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller3-3/+9
Conflicts: drivers/net/ethernet/freescale/fsl_pq_mdio.c net/batman-adv/translation-table.c net/ipv6/route.c
2011-12-13ipv6: Check dest prefix length on original route not copied one in ↵David S. Miller1-1/+1
rt6_alloc_cow(). After commit 8e2ec639173f325977818c45011ee176ef2b11f6 ("ipv6: don't use inetpeer to store metrics for routes.") the test in rt6_alloc_cow() for setting the ANYCAST flag is now wrong. 'rt' will always now have a plen of 128, because it is set explicitly to 128 by ip6_rt_copy. So to restore the semantics of the test, check the destination prefix length of 'ort'. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-13ipv6: If neigh lookup fails during icmp6 dst allocation, propagate error.David S. Miller1-2/+4
Don't just succeed with a route that has a NULL neighbour attached. This follows the behavior of addrconf_dst_alloc(). Allowing this kind of route to end up with a NULL neigh attached will result in packet drops on output until the route is somehow invalidated, since nothing will meanwhile try to lookup the neigh again. A statistic is bumped for the case where we see a neigh-less route on output, but the resulting packet drop is otherwise silent in nature, and frankly it's a hard error for this to happen and ipv6 should do what ipv4 does which is say something in the kernel logs. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-13netfilter: add ipv6 reverse path filter matchFlorian Westphal3-0/+144
This is not merged with the ipv4 match into xt_rpfilter.c to avoid ipv6 module dependency issues. Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2011-12-12per-netns ipv4 sysctl_tcp_memGlauber Costa2-1/+2
This patch allows each namespace to independently set up its levels for tcp memory pressure thresholds. This patch alone does not buy much: we need to make this values per group of process somehow. This is achieved in the patches that follows in this patchset. Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-12tcp memory pressure controlsGlauber Costa1-0/+5
This patch introduces memory pressure controls for the tcp protocol. It uses the generic socket memory pressure code introduced in earlier patches, and fills in the necessary data in cg_proto struct. Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-12foundations of per-cgroup memory pressure controlling.Glauber Costa1-1/+1
This patch replaces all uses of struct sock fields' memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem to acessor macros. Those macros can either receive a socket argument, or a mem_cgroup argument, depending on the context they live in. Since we're only doing a macro wrapping here, no performance impact at all is expected in the case where we don't have cgroups disabled. Signed-off-by: Glauber Costa <glommer@parallels.com> Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> CC: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-12ipip, sit: copy parms.name after register_netdeviceTed Feng1-1/+6
Same fix as 731abb9cb2 for ipip and sit tunnel. Commit 1c5cae815d removed an explicit call to dev_alloc_name in ipip_tunnel_locate and ipip6_tunnel_locate, because register_netdevice will now create a valid name, however the tunnel keeps a copy of the name in the private parms structure. Fix this by copying the name back after register_netdevice has successfully returned. This shows up if you do a simple tunnel add, followed by a tunnel show: $ sudo ip tunnel add mode ipip remote 10.2.20.211 $ ip tunnel tunl0: ip/ip remote any local any ttl inherit nopmtudisc tunl%d: ip/ip remote 10.2.20.211 local any ttl inherit $ sudo ip tunnel add mode sit remote 10.2.20.212 $ ip tunnel sit0: ipv6/ip remote any local any ttl 64 nopmtudisc 6rd-prefix 2002::/16 sit%d: ioctl 89f8 failed: No such device sit%d: ipv6/ip remote 10.2.20.212 local any ttl inherit Cc: stable@vger.kernel.org Signed-off-by: Ted Feng <artisdom@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-12ipv6: Fix for adding multicast route for loopback device automatically.Li Wei1-1/+2
There is no obvious reason to add a default multicast route for loopback devices, otherwise there would be a route entry whose dst.error set to -ENETUNREACH that would blocking all multicast packets. ==================== [ more detailed explanation ] The problem is that the resulting routing table depends on the sequence of interface's initialization and in some situation, that would block all muticast packets. Suppose there are two interfaces on my computer (lo and eth0), if we initailize 'lo' before 'eth0', the resuting routing table(for multicast) would be # ip -6 route show | grep ff00:: unreachable ff00::/8 dev lo metric 256 error -101 ff00::/8 dev eth0 metric 256 When sending multicasting packets, routing subsystem will return the first route entry which with a error set to -101(ENETUNREACH). I know the kernel will set the default ipv6 address for 'lo' when it is up and won't set the default multicast route for it, but there is no reason to stop 'init' program from setting address for 'lo', and that is exactly what systemd did. I am sure there is something wrong with kernel or systemd, currently I preferred kernel caused this problem. ==================== Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-09udp: Export code sk lookup routinesPavel Emelyanov1-1/+2
The UDP diag get_exact handler will require them to find a socket by provided net, [sd]addr-s, [sd]ports and device. Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-06ipv6: Move xfrm_lookup() call down into icmp6_dst_alloc().David S. Miller3-28/+11
And return error pointers. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-06ipv6: Make third arg to anycast_dst_alloc() bool.David S. Miller3-3/+3
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-05net: Rename dst_get_neighbour{, _raw} to dst_get_neighbour_noref{, _raw}.David Miller6-17/+17
To reflect the fact that a refrence is not obtained to the resulting neighbour entry. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Roland Dreier <roland@purestorage.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-25 23:35:56 +0000