| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch updates the GRO handlers for GRE, VXLAN, GENEVE, and FOU so that
we do not clear the flush bit until after we have called the next level GRO
handler. Previously this was being cleared before parsing through the list
of frames, however this resulted in several paths where either the bit
needed to be reset but wasn't as in the case of FOU, or cases where it was
being set as in GENEVE. By just deferring the clearing of the bit until
after the next level protocol has been parsed we can avoid any unnecessary
bit twiddling and avoid bugs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a common kernel function to get the number of bytes available
on a TCP socket. This is based on code in INQ getsockopt and we now call
the function for that getsockopt.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
1) Remove useless debug message when deleting IPVS service, from
Yannick Brosseau.
2) Get rid of compilation warning when CONFIG_PROC_FS is unset in
several spots of the IPVS code, from Arnd Bergmann.
3) Add prandom_u32 support to nft_meta, from Florian Westphal.
4) Remove unused variable in xt_osf, from Sudip Mukherjee.
5) Don't calculate IP checksum twice from netfilter ipv4 defrag hook
since fixing af_packet defragmentation issues, from Joe Stringer.
6) On-demand hook registration for iptables from netns. Instead of
registering the hooks for every available netns whenever we need
one of the support tables, we register this on the specific netns
that needs it, patchset from Florian Westphal.
7) Add missing port range selection to nf_tables masquerading support.
BTW, just for the record, there is a typo in the description of
5f6c253ebe93b0 ("netfilter: bridge: register hooks only when bridge
interface is added") that refers to the cluster match as deprecated, but
it is actually the CLUSTERIP target (which registers hooks
inconditionally) the one that is scheduled for removal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The assumptions from commit 0c1d70af924b ("net: use dst_cache for vxlan
device"), 468dfffcd762 ("geneve: add dst caching support") and 3c1cb4d2604c
("net/ipv4: add dst cache support for gre lwtunnels") on dst_cache usage
when ip_tunnel_info is used is unfortunately not always valid as assumed.
While it seems correct for ip_tunnel_info front-ends such as OVS, eBPF
however can fill in ip_tunnel_info for consumers like vxlan, geneve or gre
with different remote dsts, tos, etc, therefore they cannot be assumed as
packet independent.
Right now vxlan, geneve, gre would cache the dst for eBPF and every packet
would reuse the same entry that was first created on the initial route
lookup. eBPF doesn't store/cache the ip_tunnel_info, so each skb may have
a different one.
Fix it by adding a flag that checks the ip_tunnel_info. Also the !tos test
in vxlan needs to be handeled differently in this context as it is currently
inferred from ip_tunnel_info as well if present. ip_tunnel_dst_cache_usable()
helper is added for the three tunnel cases, which checks if we can use dst
cache.
Fixes: 0c1d70af924b ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd762 ("geneve: add dst caching support")
Fixes: 3c1cb4d2604c ("net/ipv4: add dst cache support for gre lwtunnels")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If final packet (ACK) of 3WHS is lost, it appears we do not properly
account the following incoming segment into tcpi_segs_in
While we are at it, starts segs_in with one, to count the SYN packet.
We do not yet count number of SYN we received for a request sock, we
might add this someday.
packetdrill script showing proper behavior after fix :
// Tests tcpi_segs_in when 3rd packet (ACK) of 3WHS is lost
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
+.020 < P. 1:1001(1000) ack 1 win 32792
+0 accept(3, ..., ...) = 4
+.000 %{ assert tcpi_segs_in == 2, 'tcpi_segs_in=%d' % tcpi_segs_in }%
Fixes: 2efd055c53c06 ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, arp_rcv() always return zero on a packet delivery upcall.
To make its behavior more compliant with the way this API should be
used, this patch changes this to let it return NET_RX_SUCCESS when the
packet is proper handled, and NET_RX_DROP otherwise.
v1->v2:
If sanity check is failed, call kfree_skb() instead of consume_skb(), then
return the correct return value.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current reserved_tailroom calculation fails to take hlen and tlen into
account.
skb:
[__hlen__|__data____________|__tlen___|__extra__]
^ ^
head skb_end_offset
In this representation, hlen + data + tlen is the size passed to alloc_skb.
"extra" is the extra space made available in __alloc_skb because of
rounding up by kmalloc. We can reorder the representation like so:
[__hlen__|__data____________|__extra__|__tlen___]
^ ^
head skb_end_offset
The maximum space available for ip headers and payload without
fragmentation is min(mtu, data + extra). Therefore,
reserved_tailroom
= data + extra + tlen - min(mtu, data + extra)
= skb_end_offset - hlen - min(mtu, skb_end_offset - hlen - tlen)
= skb_tailroom - min(mtu, skb_tailroom - tlen) ; after skb_reserve(hlen)
Compare the second line to the current expression:
reserved_tailroom = skb_end_offset - min(mtu, skb_end_offset)
and we can see that hlen and tlen are not taken into account.
The min() in the third line can be expanded into:
if mtu < skb_tailroom - tlen:
reserved_tailroom = skb_tailroom - mtu
else:
reserved_tailroom = tlen
Depending on hlen, tlen, mtu and the number of multicast address records,
the current code may output skbs that have less tailroom than
dev->needed_tailroom or it may output more skbs than needed because not all
space available is used.
Fixes: 4c672e4b ("ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
8cc785f6f429c2a3fb81745dc142cbd72a462c4a ("net: ipv4: make the ping
/proc code AF-independent") removed the code using it, but renamed this
variable instead of removing it.
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Complete masquerading support by allowing port range selection.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
delay hook registration until the table is being requested inside a
namespace.
Historically, a particular table (iptables mangle, ip6tables filter, etc)
was registered on module load.
When netns support was added to iptables only the ip/ip6tables ruleset was
made namespace aware, not the actual hook points.
This means f.e. that when ipt_filter table/module is loaded on a system,
then each namespace on that system has an (empty) iptables filter ruleset.
In other words, if a namespace sends a packet, such skb is 'caught' by
netfilter machinery and fed to hooking points for that table (i.e. INPUT,
FORWARD, etc).
Thanks to Eric Biederman, hooks are no longer global, but per namespace.
This means that we can avoid allocation of empty ruleset in a namespace and
defer hook registration until we need the functionality.
We register a tables hook entry points ONLY in the initial namespace.
When an iptables get/setockopt is issued inside a given namespace, we check
if the table is found in the per-namespace list.
If not, we attempt to find it in the initial namespace, and, if found,
create an empty default table in the requesting namespace and register the
needed hooks.
Hook points are destroyed only once namespace is deleted, there is no
'usage count' (it makes no sense since there is no 'remove table' operation
in xtables api).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This change prepares for upcoming on-demand xtables hook registration.
We change the protoypes of the register/unregister functions.
A followup patch will then add nf_hook_register/unregister calls
to the iptables one.
Once a hook is registered packets will be picked up, so all assignments
of the form
net->ipv4.iptable_$table = new_table
have to be moved to ip(6)t_register_table, else we can see NULL
net->ipv4.iptable_$table later.
This patch doesn't change functionality; without this the actual change
simply gets too big.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since commit 0848f6428ba3 ("inet: frags: fix defragmented packet's IP
header for af_packet"), ip_send_check() would be called twice for
defragmentation that occurs from netfilter ipv4 defrag hooks. Remove the
extra call.
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
After commit 52bd2d62ce67 ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP probe log timestamps use struct timespec which is
not y2038 safe. Even though timespec might be good enough here
as it is used to represent delta time, the plan is to get rid
of all uses of timespec in the kernel.
Replace with struct timespec64 which is y2038 safe.
Prints still use unsigned long format and type.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ICMP timestamp messages and IP source route options require
timestamps to be in milliseconds modulo 24 hours from
midnight UT format.
Add inet_current_timestamp() function to support this. The function
returns the required timestamp in network byte order.
Timestamp calculation is also changed to call ktime_get_real_ts64()
which uses struct timespec64. struct timespec64 is y2038 safe.
Previously it called getnstimeofday() which uses struct timespec.
struct timespec is not y2038 safe.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On reviewing the code I realized that GRE and UDP tunnels could cause a
kernel panic if we used GSO to segment a large UDP frame that was sent
through the tunnel with an outer checksum and hardware offloads were not
available.
In order to correct this we need to update the feature flags that are
passed to the skb_segment function so that in the event of UDP
fragmentation being requested for the inner header the segmentation
function will correctly generate the checksum for the payload if we cannot
segment the outer header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When selecting an address in context of a VRF, the vrf master should be
preferred for address selection. If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.
Relevant commands from his script:
ip addr add 9.9.9.9/32 dev lo
ip link set lo up
ip link add name vrf0 type vrf table 101
ip rule add oif vrf0 table 101
ip rule add iif vrf0 table 101
ip link set vrf0 up
ip addr add 10.0.0.3/32 dev vrf0
ip link add name dummy2 type dummy
ip link set dummy2 master vrf0 up
--> note dummy2 has no address - unnumbered device
ip route add 10.2.2.2/32 dev dummy2 table 101
ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02
tcpdump -ni dummy2 &
And using ping instead of his socat example:
$ ping -I vrf0 -c1 10.2.2.2
ping: Warning: source address might be selected on device other than vrf0.
PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.
>From tcpdump:
12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
Note the source address is from lo and is not a VRF local address. With
this patch:
$ ping -I vrf0 -c1 10.2.2.2
PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.
>From tcpdump:
12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64
Now the source address comes from vrf0.
The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.
IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.
Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL
skbs down. This can easily happen with UDP+IPv4 sockets with the first
MSG_MORE write smaller than the MTU, second write is a sendfile.
Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path,
were we calculate the checksum manually during copying.
Commit d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked
sockets") started to exposes this bug.
Fixes: d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets")
Reported-by: Jiri Benc <jbenc@redhat.com>
Cc: Jiri Benc <jbenc@redhat.com>
Reported-by: Wakko Warner <wakko@animx.eu.org>
Cc: Wakko Warner <wakko@animx.eu.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the validation checks for the new array-based TCP SO_REUSEPORT
validation was unintentionally dropped in ea8add2b1903. This adds it back.
Lack of this check allows the user to allocate multiple sock_reuseport
structures (leaking all but the first).
Fixes: ea8add2b1903 ("tcp/dccp: better use of ephemeral ports in bind()")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it's converted into msecs, thus HZ=1000 intact.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 740b0f1841f6 ("tcp: switch rtt estimations to usec resolution")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by gre
as it modifies the skb on xmit.
Also, clean up whitespace in ipgre_tap_setup when we're already touching it.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Part of skb_scrub_packet was open coded in iptunnel_pull_header. Let it call
skb_scrub_packet directly instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ilya reported following lockdep splat:
kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory
ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0: (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1: (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2: (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.
We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.
Reported-by: Ilya Dryomov <idryomov@gmail.com>
Fixes: ebb516af60e1 ("tcp/dccp: fix race at listener dismantle phase")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.
Fix this issue by checking and removing route cache when we get route.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
crypto_alloc_hash never returns NULL
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no longer any in-tree drivers that use it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all the ip fragmentation related sysctls are namespaceified
there is no reason to hide them anymore from "root" users inside
containers.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When igmp related sysctl were namespacified their initializatin was
erroneously put into the tcp socket namespace constructor. This
patch moves the relevant code into the igmp namespace constructor to
keep things consistent.
Also sprinkle some #ifdefs to silence warnings
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcpi_min_rtt reports the minimal rtt observed by TCP stack for the flow,
in usec unit. Might be ~0U if not yet known.
tcpi_notsent_bytes reports the amount of bytes in the write queue that
were not yet sent.
This is done in a single patch to not add a temporary 32bit padding hole
in tcp_info.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.
The bug was added for IPv4 only.
Fixes: 079096f103fac ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of UDP traffic with datagram length below MTU this
gives about 4% performance increase
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current ip_tunnel cache implementation is prone to a race
that will cause the wrong dst to be cached on cuncurrent dst cache
miss and ip tunnel update via netlink.
Replacing with the generic implementation fix the issue.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some cases where rtt_us derives from deltas of jiffies,
instead of using usec timestamps.
Since we want to track minimal rtt, better to assume a delta of 0 jiffie
might be in fact be very close to 1 jiffie.
It is kind of sad jiffies_to_usecs(1) calls a function instead of simply
using a constant.
Fixes: f672258391b42 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.
Callers are responsible for the freeing.
Many thanks to Dmitry for the report and diagnostic.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All users now pass false, so we can remove it, and remove the code that
was conditional upon it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the dst device doesn't support it, it'll get fixed up later anyway
by validate_xmit_skb(). Also, this allows us to take advantage of LCO
to avoid summing the payload multiple times.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The arithmetic properties of the ones-complement checksum mean that a
correctly checksummed inner packet, including its checksum, has a ones
complement sum depending only on whatever value was used to initialise
the checksum field before checksumming (in the case of TCP and UDP,
this is the ones complement sum of the pseudo header, complemented).
Consequently, if we are going to offload the inner checksum with
CHECKSUM_PARTIAL, we can compute the outer checksum based only on the
packed data not covered by the inner checksum, and the initial value of
the inner checksum field.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement strategy used in __inet_hash_connect() in opposite way :
Try to find a candidate using odd ports, then fallback to even ports.
We no longer disable BH for whole traversal, but one bucket at a time.
We also use cond_resched() to yield cpu to other tasks if needed.
I removed one indentation level and tried to mirror the loop we have
in __inet_hash_connect() and variable names to ease code maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 07f4c90062f8 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), I added a very simple heuristic, so that we got better
chances to use even ports, and allow bind() users to have more available
slots.
It gave nice results, but with more than 200,000 TCP sessions on a typical
server, the ~30,000 ephemeral ports are still a rare resource.
I chose to go a step further, by looking at all even ports, and if none
was available, fallback to odd ports.
The companion patch does the same in bind(), but in opposite way.
I've seen exec times of up to 30ms on busy servers, so I no longer
disable BH for the whole traversal, but only for each hash bucket.
I also call cond_resched() to be gentle to other tasks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
