| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Switches that care about QoS might have hardware support for reserving
buffer pools for individual ports or traffic classes, and configuring
their sizes and thresholds. Through devlink-sb (shared buffers), this is
all configurable, as well as their occupancy being viewable.
Add the plumbing in DSA for these operations.
Individual drivers still need to call devlink_sb_register() with the
shared buffers they want to expose. A helper was not created in DSA for
this purpose (unlike, say, dsa_devlink_params_register), since in my
opinion it does not bring any benefit over plainly calling
devlink_sb_register() directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 54a0ed0df496 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Arrow SpeedChips XRS700x single byte tag trailer. This
is modeled on tag_trailer.c which works in a similar way.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packets ingressing on a LAG that egress on the CPU port, which are not
classified as management, will have a FORWARD tag that does not
contain the normal source device/port tuple. Instead the trunk bit
will be set, and the port field holds the LAG id.
Since the exact source port information is not available in the tag,
frames are injected directly on the LAG interface and thus do never
pass through any DSA port interface on ingress.
Management frames (TO_CPU) are not affected and will pass through the
DSA port interface as usual.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Monitor the following events and notify the driver when:
- A DSA port joins/leaves a LAG.
- A LAG, made up of DSA ports, joins/leaves a bridge.
- A DSA port in a LAG is enabled/disabled (enabled meaning
"distributing" in 802.3ad LACP terms).
When a LAG joins a bridge, the DSA subsystem will treat that as each
individual port joining the bridge. The driver may look at the port's
LAG device pointer to see if it is associated with any LAG, if that is
required. This is analogue to how switchdev events are replicated out
to all lower devices when reaching e.g. a LAG.
Drivers can optionally request that DSA maintain a linear mapping from
a LAG ID to the corresponding netdev by setting ds->num_lag_ids to the
desired size.
In the event that the hardware is not capable of offloading a
particular LAG for any reason (the typical case being use of exotic
modes like broadcast), DSA will take a hands-off approach, allowing
the LAG to be formed as a pure software construct. This is reported
back through the extended ACK, but is otherwise transparent to the
user.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a situation where a standalone port is indirectly attached to a
bridge (e.g. via a LAG) which is not offloaded, do not offload any
port attributes either. The port should behave as a standard NIC.
Previously, on mv88e6xxx, this meant that in the following setup:
br0
/
team0
/ \
swp0 swp1
If vlan filtering was enabled on br0, swp0's and swp1's QMode was set
to "secure". This caused all untagged packets to be dropped, as their
default VID (0) was not loaded into the VTU.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow DSA drivers to export stats64
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Florian reported a use-after-free bug in devlink_nl_port_fill found with
KASAN:
(devlink_nl_port_fill)
(devlink_port_notify)
(devlink_port_unregister)
(dsa_switch_teardown.part.3)
(dsa_tree_teardown_switches)
(dsa_unregister_switch)
(bcm_sf2_sw_remove)
(platform_remove)
(device_release_driver_internal)
(device_links_unbind_consumers)
(device_release_driver_internal)
(device_driver_detach)
(unbind_store)
Allocated by task 31:
alloc_netdev_mqs+0x5c/0x50c
dsa_slave_create+0x110/0x9c8
dsa_register_switch+0xdb0/0x13a4
b53_switch_register+0x47c/0x6dc
bcm_sf2_sw_probe+0xaa4/0xc98
platform_probe+0x90/0xf4
really_probe+0x184/0x728
driver_probe_device+0xa4/0x278
__device_attach_driver+0xe8/0x148
bus_for_each_drv+0x108/0x158
Freed by task 249:
free_netdev+0x170/0x194
dsa_slave_destroy+0xac/0xb0
dsa_port_teardown.part.2+0xa0/0xb4
dsa_tree_teardown_switches+0x50/0xc4
dsa_unregister_switch+0x124/0x250
bcm_sf2_sw_remove+0x98/0x13c
platform_remove+0x44/0x5c
device_release_driver_internal+0x150/0x254
device_links_unbind_consumers+0xf8/0x12c
device_release_driver_internal+0x84/0x254
device_driver_detach+0x30/0x34
unbind_store+0x90/0x134
What happens is that devlink_port_unregister emits a netlink
DEVLINK_CMD_PORT_DEL message which associates the devlink port that is
getting unregistered with the ifindex of its corresponding net_device.
Only trouble is, the net_device has already been unregistered.
It looks like we can stub out the search for a corresponding net_device
if we clear the devlink_port's type. This looks like a bit of a hack,
but also seems to be the reason why the devlink_port_type_clear function
exists in the first place.
Fixes: 3122433eb533 ("net: dsa: Register devlink ports before calling DSA driver setup()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian fainelli <f.fainelli@gmail.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210112004831.3778323-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the following happens when a DSA master driver unbinds while
there are DSA switches attached to it:
$ echo 0000:00:00.5 > /sys/bus/pci/drivers/mscc_felix/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 392 at net/core/dev.c:9507
Call trace:
rollback_registered_many+0x5fc/0x688
unregister_netdevice_queue+0x98/0x120
dsa_slave_destroy+0x4c/0x88
dsa_port_teardown.part.16+0x78/0xb0
dsa_tree_teardown_switches+0x58/0xc0
dsa_unregister_switch+0x104/0x1b8
felix_pci_remove+0x24/0x48
pci_device_remove+0x48/0xf0
device_release_driver_internal+0x118/0x1e8
device_driver_detach+0x28/0x38
unbind_store+0xd0/0x100
Located at the above location is this WARN_ON:
/* Notifier chain MUST detach us all upper devices. */
WARN_ON(netdev_has_any_upper_dev(dev));
Other stacked interfaces, like VLAN, do indeed listen for
NETDEV_UNREGISTER on the real_dev and also unregister themselves at that
time, which is clearly the behavior that rollback_registered_many
expects. But DSA interfaces are not VLAN. They have backing hardware
(platform devices, PCI devices, MDIO, SPI etc) which have a life cycle
of their own and we can't just trigger an unregister from the DSA
framework when we receive a netdev notifier that the master unregisters.
Luckily, there is something we can do, and that is to inform the driver
core that we have a runtime dependency to the DSA master interface's
device, and create a device link where that is the supplier and we are
the consumer. Having this device link will make the DSA switch unbind
before the DSA master unbinds, which is enough to avoid the WARN_ON from
rollback_registered_many.
Note that even before the blamed commit, DSA did nothing intelligent
when the master interface got unregistered either. See the discussion
here:
https://lore.kernel.org/netdev/20200505210253.20311-1-f.fainelli@gmail.com/
But this time, at least the WARN_ON is loud enough that the
upper_dev_link commit can be blamed.
The advantage with this approach vs dev_hold(master) in the attached
link is that the latter is not meant for long term reference counting.
With dev_hold, the only thing that will happen is that when the user
attempts an unbind of the DSA master, netdev_wait_allrefs will keep
waiting and waiting, due to DSA keeping the refcount forever. DSA would
not access freed memory corresponding to the master interface, but the
unbind would still result in a freeze. Whereas with device links,
graceful teardown is ensured. It even works with cascaded DSA trees.
$ echo 0000:00:00.2 > /sys/bus/pci/drivers/fsl_enetc/unbind
[ 1818.797546] device swp0 left promiscuous mode
[ 1819.301112] sja1105 spi2.0: Link is Down
[ 1819.307981] DSA: tree 1 torn down
[ 1819.312408] device eno2 left promiscuous mode
[ 1819.656803] mscc_felix 0000:00:00.5: Link is Down
[ 1819.667194] DSA: tree 0 torn down
[ 1819.711557] fsl_enetc 0000:00:00.2 eno2: Link is Down
This approach allows us to keep the DSA framework absolutely unchanged,
and the driver core will just know to unbind us first when the master
goes away - as opposed to the large (and probably impossible) rework
required if attempting to listen for NETDEV_UNREGISTER.
As per the documentation at Documentation/driver-api/device_link.rst,
specifying the DL_FLAG_AUTOREMOVE_CONSUMER flag causes the device link
to be automatically purged when the consumer fails to probe or later
unbinds. So we don't need to keep the consumer_link variable in struct
dsa_switch.
Fixes: 2f1e8ea726e9 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210111230943.3701806-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that all port object notifiers were converted to be non-transactional,
we can remove the comments that say otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.
So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.
It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For many drivers, the .port_mdb_prepare callback was not a good opportunity
to avoid any error condition, and they would suppress errors found during
the actual commit phase.
Where a logical separation between the prepare and the commit phase
existed, the function that used to implement the .port_mdb_prepare
callback still exists, but now it is called directly from .port_mdb_add,
which was modified to return an int code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Wallei <linus.walleij@linaro.org> # RTL8366
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the shim introduced in DSA for offloading the bridge ageing time
from switchdev, by first checking whether the ageing time is within the
range limits requested by the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d8a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the introduction of the switchdev API, port objects were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
object notifier structures, and converts drivers to not look at this
member.
Where driver conversion is trivial (like in the case of the Marvell
Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is
done in this patch.
Where driver conversion needs more attention (DSA, Mellanox Spectrum),
the conversion is left for subsequent patches and here we only fake the
prepare/commit phases at a lower level, just not in the switchdev
notifier itself.
Where the code has a natural structure that is best left alone as a
preparation and a commit phase (as in the case of the Ocelot switch),
that structure is left in place, just made to not depend upon the
switchdev transactional model.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef7838
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1a4 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9359e ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2fa ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d83 ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1ae3 ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d83 by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc28e
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduced in commit 37b8da1a3c68 ("net: dsa: Move FDB add/del
implementation inside DSA") in net/dsa/legacy.c, these functions were
moved again to slave.c as part of commit 2a93c1a3651f ("net: dsa: Allow
compiling out legacy support"), before actually deleting net/dsa/slave.c
in 93e86b3bc842 ("net: dsa: Remove legacy probing support"). Along with
that movement there should have been a deletion of the prototypes from
dsa_priv.h, they are not useful.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210108233054.1222278-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This effectively reverts commit 60724d4bae14 ("net: dsa: Add support for
DSA specific notifiers"). The reason is that since commit 2f1e8ea726e9
("net: dsa: link interfaces with the DSA master to get rid of lockdep
warnings"), it appears that there is a generic way to achieve the same
purpose. The only user thus far, the Broadcom SYSTEMPORT driver, was
converted to use the generic notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using the NETDEV_CHANGEUPPER notifications, drivers can be aware when
they are enslaved to e.g. a bridge by calling netif_is_bridge_master().
Export this helper from DSA to get the equivalent functionality of
determining whether the upper interface of a CHANGEUPPER notifier is a
DSA switch interface or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is a bit strange to see something as specific as Broadcom SYSTEMPORT
bits in the main DSA include file. Move these away into a separate
header, and have the tagger and the SYSTEMPORT driver include them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
neighbors
Some DSA switches (and not only) cannot learn source MAC addresses from
packets injected from the CPU. They only perform hardware address
learning from inbound traffic.
This can be problematic when we have a bridge spanning some DSA switch
ports and some non-DSA ports (which we'll call "foreign interfaces" from
DSA's perspective).
There are 2 classes of problems created by the lack of learning on
CPU-injected traffic:
- excessive flooding, due to the fact that DSA treats those addresses as
unknown
- the risk of stale routes, which can lead to temporary packet loss
To illustrate the second class, consider the following situation, which
is common in production equipment (wireless access points, where there
is a WLAN interface and an Ethernet switch, and these form a single
bridging domain).
AP 1:
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
| ^ ^
| | |
| | |
| Client A Client B
|
|
|
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
AP 2
- br0 of AP 1 will know that Clients A and B are reachable via wlan0
- the hardware fdb of a DSA switch driver today is not kept in sync with
the software entries on other bridge ports, so it will not know that
clients A and B are reachable via the CPU port UNLESS the hardware
switch itself performs SA learning from traffic injected from the CPU.
Nonetheless, a substantial number of switches don't.
- the hardware fdb of the DSA switch on AP 2 may autonomously learn that
Client A and B are reachable through swp0. Therefore, the software br0
of AP 2 also may or may not learn this. In the example we're
illustrating, some Ethernet traffic has been going on, and br0 from AP
2 has indeed learnt that it can reach Client B through swp0.
One of the wireless clients, say Client B, disconnects from AP 1 and
roams to AP 2. The topology now looks like this:
AP 1:
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
| ^
| |
| Client A
|
|
| Client B
| |
| v
+------------+ +------------+ +------------+ +------------+ +------------+
| swp0 | | swp1 | | swp2 | | swp3 | | wlan0 |
+------------+ +------------+ +------------+ +------------+ +------------+
+------------------------------------------------------------------------+
| br0 |
+------------------------------------------------------------------------+
AP 2
- br0 of AP 1 still knows that Client A is reachable via wlan0 (no change)
- br0 of AP 1 will (possibly) know that Client B has left wlan0. There
are cases where it might never find out though. Either way, DSA today
does not process that notification in any way.
- the hardware FDB of the DSA switch on AP 1 may learn autonomously that
Client B can be reached via swp0, if it receives any packet with
Client 1's source MAC address over Ethernet.
- the hardware FDB of the DSA switch on AP 2 still thinks that Client B
can be reached via swp0. It does not know that it has roamed to wlan0,
because it doesn't perform SA learning from the CPU port.
Now Client A contacts Client B.
AP 1 routes the packet fine towards swp0 and delivers it on the Ethernet
segment.
AP 2 sees a frame on swp0 and its fdb says that the destination is swp0.
Hairpinning is disabled => drop.
This problem comes from the fact that these switches have a 'blind spot'
for addresses coming from software bridging. The generic solution is not
to assume that hardware learning can be enabled somehow, but to listen
to more bridge learning events. It turns out that the bridge driver does
learn in software from all inbound frames, in __br_handle_local_finish.
A proper SWITCHDEV_FDB_ADD_TO_DEVICE notification is emitted for the
addresses serviced by the bridge on 'foreign' interfaces. The software
bridge also does the right thing on migration, by notifying that the old
entry is deleted, so that does not need to be special-cased in DSA. When
it is deleted, we just need to delete our static FDB entry towards the
CPU too, and wait.
The problem is that DSA currently only cares about SWITCHDEV_FDB_ADD_TO_DEVICE
events received on its own interfaces, such as static FDB entries.
Luckily we can change that, and DSA can listen to all switchdev FDB
add/del events in the system and figure out if those events were emitted
by a bridge that spans at least one of DSA's own ports. In case that is
true, DSA will also offload that address towards its own CPU port, in
the eventuality that there might be bridge clients attached to the DSA
switch who want to talk to the station connected to the foreign
interface.
In terms of implementation, we need to keep the fdb_info->added_by_user
check for the case where the switchdev event was targeted directly at a
DSA switch port. But we don't need to look at that flag for snooped
events. So the check is currently too late, we need to move it earlier.
This also simplifies the code a bit, since we avoid uselessly allocating
and freeing switchdev_work.
We could probably do some improvements in the future. For example,
multi-bridge support is rudimentary at the moment. If there are two
bridges spanning a DSA switch's ports, and both of them need to service
the same MAC address, then what will happen is that the migration of one
of those stations will trigger the deletion of the FDB entry from the
CPU port while it is still used by other bridge. That could be improved
with reference counting but is left for another time.
This behavior needs to be enabled at driver level by setting
ds->assisted_learning_on_cpu_port = true. This is because we don't want
to inflict a potential performance penalty (accesses through
MDIO/I2C/SPI are expensive) to hardware that really doesn't need it
because address learning on the CPU port works there.
Reported-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Right now, the following would happen for a switch driver that does not
implement .port_fdb_add or .port_fdb_del.
dsa_slave_switchdev_event returns NOTIFY_OK and schedules:
-> dsa_slave_switchdev_event_work
-> dsa_port_fdb_add
-> dsa_port_notify(DSA_NOTIFIER_FDB_ADD)
-> dsa_switch_fdb_add
-> if (!ds->ops->port_fdb_add) return -EOPNOTSUPP;
-> an error is printed with dev_dbg, and
dsa_fdb_offload_notify(switchdev_work) is not called.
We can avoid scheduling the worker for nothing and say NOTIFY_DONE.
Because we don't call dsa_fdb_offload_notify, the static FDB entry will
remain just in the software bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
statement
We'll need to start listening to SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE
events even for interfaces where dsa_slave_dev_check returns false, so
we need that check inside the switch-case statement for SWITCHDEV_FDB_*.
This movement also avoids a useless allocation / free of switchdev_work
on the untreated "default event" case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently DSA doesn't add FDB entries on the CPU port, because it only
does so through switchdev, which is associated with a net_device, and
there are none of those for the CPU port.
But actually FDB addresses on the CPU port have some use cases of their
own, if the switchdev operations are initiated from within the DSA
layer. There is just one problem with the existing code: it passes a
structure in dsa_switchdev_event_work which was retrieved directly from
switchdev, so it contains a net_device. We need to generalize the
contents to something that covers the CPU port as well: the "ds, port"
tuple is fine for that.
Note that the new procedure for notifying the successful FDB offload is
inspired from the rocker model.
Also, nothing was being done if added_by_user was false. Let's check for
that a lot earlier, and don't actually bother to schedule the worker
for nothing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dev_close() call was added in commit c9eb3e0f8701 ("net: dsa: Add
support for learning FDB through notification") "to indicate inconsistent
situation" when we could not delete an FDB entry from the port.
bridge fdb del d8:58:d7:00:ca:6d dev swp0 self master
It is a bit drastic and at the same time not helpful if the above fails
to only print with netdev_dbg log level, but on the other hand to bring
the interface down.
So increase the verbosity of the error message, and drop dev_close().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Looking for an -EINVAL all over the dsa code could take hours for
inexperienced DSA users.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210106090915.21439-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These warnings become somewhat more informative when they include the
MTU value that could not be set and not just the errno.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201205133944.10182-1-rasmus.villemoes@prevas.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unused and add needed includes. No functional change.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If dsa_switch_ops::port_txtstamp() returns false, clone will be freed
immediately. Shouldn't store a pointer to freed memory.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201119110906.25558-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use a consistent style of one-line/multi-line comments throughout the
file.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethertype DSA encodes exactly the same information in the DSA tag as
the non-ethertype variety. So refactor out the common parts and reuse
them for both protocols.
This is ensures tag parsing and generation is always consistent across
all mv88e6xxx chips.
While we are at it, explicitly deal with all possible CPU codes on
receive, making sure to set offload_fwd_mark as appropriate.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When receiving an IGMP/MLD frame with a TO_CPU tag, the switch has not
performed any forwarding of it. This means that we should not set the
offload_fwd_mark on the skb, in case a software bridge wants it
forwarded.
This is a port of:
1ed9ec9b08ad ("dsa: Allow forwarding of redirected IGMP traffic")
Which corrected the issue for chips using EDSA tags, but not for those
using regular DSA tags.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netdev->tstats instead of a member of dsa_slave_priv for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some switches rely on unique pvids to ensure port separation in
standalone mode, because they don't have a port forwarding matrix
configurable in hardware. So, setups like a group of 2 uppers with the
same VLAN, swp0.100 and swp1.100, will cause traffic tagged with VLAN
100 to be autonomously forwarded between these switch ports, in spite
of there being no bridge between swp0 and swp1.
These drivers need to prevent this from happening. They need to have
VLAN filtering enabled in standalone mode (so they'll drop frames tagged
with unknown VLANs) and they can only accept an 8021q upper on a port as
long as it isn't installed on any other port too. So give them the
chance to veto bad user requests.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Kurt: Pass info instead of ptr]
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Hirschmann Hellcreek TSN switches have a special tagging protocol for frames
exchanged between the CPU port and the master interface. The format is a one
byte trailer indicating the destination or origin port.
It's quite similar to the Micrel KSZ tagging. That's why the implementation is
based on that code.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: Per Forlin <per.forlin@axis.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
This one is interesting, the DSA tag is 8 bytes on RX and 4 bytes on TX.
Because DSA is unaware of asymmetrical tag lengths, the overhead/needed
headroom is declared as 8 bytes and therefore 4 bytes larger than it
needs to be. If this becomes a problem, and the GSWIP driver can't be
converted to a uniform header length, we might need to make DSA aware of
separate RX/TX overhead values.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Similar to the EtherType DSA tagger, the old Marvell tagger can
transform an 802.1Q header if present into a DSA tag, so there is no
headroom required in that case. But we are ensuring that it exists,
regardless (practically speaking, the headroom must be 4 bytes larger
than it needs to be).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Note that the VLAN code path needs a smaller extra headroom than the
regular EtherType DSA path. That isn't a problem, because this tagger
declares the larger tag length (8 bytes vs 4) as the protocol overhead,
so we are covered in both cases.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a central TX reallocation procedure that accounts for
the tagger's needed headroom in a generic way, we can remove the
skb_cow_head call.
Cc: John Crispin <john@phrozen.org>
Cc: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The caller (dsa_slave_xmit) guarantees that the frame length is at least
ETH_ZLEN and that enough memory for tail tagging is available.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The caller (dsa_slave_xmit) guarantees that the frame length is at least
ETH_ZLEN and that enough memory for tail tagging is available.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At the moment, taggers are left with the task of ensuring that the skb
headers are writable (which they aren't, if the frames were cloned for
TX timestamping, for flooding by the bridge, etc), and that there is
enough space in the skb data area for the DSA tag to be pushed.
Moreover, the life of tail taggers is even harder, because they need to
ensure that short frames have enough padding, a problem that normal
taggers don't have.
The principle of the DSA framework is that everything except for the
most intimate hardware specifics (like in this case, the actual packing
of the DSA tag bits) should be done inside the core, to avoid having
code paths that are very rarely tested.
So provide a TX reallocation procedure that should cover the known needs
of DSA today.
Note that this patch also gives the network stack a good hint about the
headroom/tailroom it's going to need. Up till now it wasn't doing that.
So the reallocation procedure should really be there only for the
exceptional cases, and for cloned packets which need to be unshared.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Christian Eggers <ceggers@arri.de> # For tail taggers only
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Fixes: 7a6ffe764be3 ("net: dsa: point out the tail taggers")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201016171603.10587-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the code by using new function dev_fetch_sw_netstats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/b6047017-8226-6b7e-a3cd-064e69fdfa27@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
