| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If the phy interface mode is not found in devicetree, or if devicetree
is not configured, of_get_phy_mode returns -ENODEV. The current code
sets the phy interface mode to the return value from of_get_phy_mode
without checking if it is valid.
This invalid phy interface mode is passed as parameter to of_phy_connect
or to phy_connect_direct. This sets the phy interface mode to the invalid
value, which in turn causes problems for any code using phydev->interface.
Fixes: b31f65fb4383 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Fixes: 0d8bcdd383b8 ("net: dsa: allow for more complex PHY setups")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dsa_slave_phy_setup() finds the phy for the port via device tree and
using of_phy_connect(), or it uses the fall back of taking a phy from
the switch internal mdio bus and calling phy_connect_direct(). Either
way, if a phy is found, phy_attach_direct() is called to attach the
phy to the slave device.
In dsa_slave_create(), a second call to phy_attach() is made. This
results in the warning "PHY already attached". Remove this second,
redundant attaching of the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of connected switches was sourced from the number of
children to the DSA node, change it to the number of available
children, skipping any disabled switches.
Fixes: 5e95329b701c4 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.
As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:
static struct dsa_chip_data switch_cdata = {
[...]
.port_names[0] = "sw0",
.port_names[1] = "sw1",
.port_names[2] = "sw2",
.port_names[3] = "sw3",
.port_names[4] = "sw4",
.port_names[5] = "cpu",
};
DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
In case we cannot attach to our slave netdevice PHY, error out and
propagate that error up to the caller: dsa_slave_create().
Fixes: 0d8bcdd383b8 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case there is no PHY at the designated address on the internal
switch, we would basically de-reference a null pointer here:
dsa_slave_phy_setup(...)
{
p->phy = ds->slave_mii_bus->phy_map[p->port];
phy_connect_direct(slave_dev, p->phy, dsa_slave_adjust_link,
^------
This can be triggered when the platform configuration (platform_data or
Device Tree) indicates there should be a PHY device at this address, but
the HW is non-responsive, such that we cannot attach a PHY device at
this specific location.
Fix this by checking the return value prior to calling
phy_connect_direct().
CC: Andrew Lunn <andrew@lunn.ch>
Fixes: b31f65fb4383 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kcalloc manages count*sizeof overflow.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kmalloc_array manages count*sizeof overflow.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neaten and standardize the logging output.
Other miscellanea:
o Use pr_notice_once instead of a guard flag.
o Convert existing pr_<level> uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
|
|
Conflicts:
drivers/net/phy/marvell.c
Simple overlapping changes in drivers/net/phy/marvell.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for reading switch registers with 'ethtool -d'.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some chips it is possible to access the switch eeprom.
Add infrastructure support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switches provide chip temperature data.
Add support for reporting it through the hwmon subsystem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting skb->protocol to a private protocol type may result in warning
messages such as
e1000e 0000:00:19.0 em1: checksum_partial proto=dada!
This happens if the L3 protocol is IP or IPv6 and skb->ip_summed is set
to CHECKSUM_PARTIAL. Looking through the code, it appears that changing
skb->protocol for transmitted packets is not necessary and may actually
be harmful. For example, it prevents purposely unmodified (from a DSA
perspective) network drivers from properly setting up their transmit
checksum offload pointers since they inspect skb->protocol to set up the
IPv4 header or IPv6 header pointers. So don't unnecessarily change the
protocol field.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there is a mismatch between enabled tagging protocols and the
protocol the switch supports, error out, rather than continue with a
situation which is unlikely to work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
cc: alexander.h.duyck@intel.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e646a ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/dsa/slave.c uses functions and structures declared in phy_fixed.h
but does not explicitely include it, while dsa.h needs structure
declarations for 'struct ethtool_wolinfo' and 'struct ethtool_eee', fix
those by including the correct header files.
Fixes: ec9436baedb6 ("net: dsa: allow drivers to do link adjustment")
Fixes: ce31b31c68e7 ("net: dsa: allow updating fixed PHY link information")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f7f1de51edbd ("net: dsa: start and stop the PHY state machine")
add calls to phy_start() in dsa_slave_open() respectively phy_stop() in
dsa_slave_close().
We also call phy_start_aneg() in dsa_slave_create(), and this call is
messing up with the PHY state machine, since we basically start the
auto-negotiation, and later on restart it when calling phy_start().
phy_start() does not currently handle the PHY_FORCING or PHY_AN states
properly, but such a fix would be too invasive for this window.
Fixes: f7f1de51edbd ("net: dsa: start and stop the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_switch_suspend() and dsa_switch_resume() functions are only used
when PM_SLEEP is enabled, so they need #ifdef CONFIG_PM_SLEEP protection
to avoid a compiler warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow switches driver to query and enable/disable EEE on a per-port
basis by implementing the ethtool_{get,set}_eee settings and delegating
these operations to the switch driver.
set_eee() will need to coordinate with the PHY driver to make sure that
EEE is enabled, the link-partner supports it and the auto-negotiation
result is satisfactory.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever a per-port network device is used/unused, invoke the switch
driver port_enable/port_disable callbacks to allow saving as much power
as possible by disabling unused parts of the switch (RX/TX logic, memory
arrays, PHYs...). We supply a PHY device argument to make sure the
switch driver can act on the PHY device if needed (like putting/taking
the PHY out of deep low power mode).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dsa_slave_open() should start the PHY library state machine for its PHY
interface, and dsa_slave_close() should stop the PHY library state
machine accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow switch drivers to implement per-port Wake-on-LAN getter and
setters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an abstraction layer to suspend/resume switch devices, doing the
following split:
- suspend/resume the slave network devices and their corresponding PHY
devices
- suspend/resume the switch hardware using switch driver callbacks
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch drivers (e.g: bcm_sf2) may have to communicate specific
workarounds or flags towards the PHY device driver. Allow switches
driver to be delegated that task by introducing a get_phy_flags()
callback which will do just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dsa_of_probe() still used cd->mii_bus instead of cd->host_dev when
building with CONFIG_OF=y. Fix this by making the replacement here as
well.
Fixes: b4d2394d01b ("dsa: Replace mii_bus with a generic host device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change addresses several issues.
First, it was possible to set tag_protocol without setting the ops pointer.
To correct that I have reordered things so that rcv is now populated before
we set tag_protocol.
Second, it didn't make much sense to keep setting the device ops each time a
new slave was registered. So by moving the receive portion out into root
switch initialization that issue should be addressed.
Third, I wanted to avoid sending tags if the rcv pointer was not registered
so I changed the tag check to verify if the rcv function pointer is set on
the root tree. If it is then we start sending DSA tagged frames.
Finally I split the device ops pointer in the structures into two spots. I
placed the rcv function pointer in the root switch since this makes it
easiest to access from there, and I placed the xmit function pointer in the
slave for the same reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1dae37 ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.
Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/dsa/dsa.c:624:20: sparse: symbol 'dsa_pack_type' was not declared.
Should it be static?
Fixes: 3e8a72d1dae374 ("net: dsa: reduce number of protocol hooks")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:
- configuration of the external switch port interface: MII, RevMII,
RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
unused
Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 4-bytes Broadcom tag that built-in switches such as
the Starfighter 2 might insert when receiving packets, or that we need
to insert while targetting specific switch ports. We use a fake local
EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure
we can assign DSA-specific network operations within the DSA drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow switch drivers to hook a PHY link update callback to perform
port-specific link work.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever libphy determines that the link status of a given PHY/port has
changed, allow to call into the switch driver link adjustment callback
so proper actions can be taken care of by the switch driver upon link
notification.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case switch port tagging is disabled (voluntarily, or the switch just
does not support it), allow us to continue using the defined set of
dsa_device_ops in net/dsa/slave.c.
We introduce dsa_protocol_is_tagged() to check whether we need to
override skb->protocol and go through the DSA-specifif packet_type
function, or if we just go on and receive the SKB through the normal
path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the DSA slave interface to be bound to an arbitray PHY, not just
the ones that are available as child PHY devices of the switch MDIO bus.
This allows us for instance to have external PHYs connected to a
separate MDIO bus, but yet also connected to a given switch port.
Under certain configurations, the physical port mask might not be a 1:1
mapping to the MII PHYs mask. This is the case, if e.g: Port 1 of the
switch is used and connects to a PHY at a MDIO address different than 1.
Introduce a phys_mii_mask variable which allows driver to implement and
divert their own MDIO read/writes operations for a subset of the MDIO
PHY addresses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will later use the per-port device_node pointer to fetch a bunch of
port-specific properties.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We might need to fetch additional resources from the device tree node
pointer, such as register ranges or other properties. Keep a device_node
pointer around for this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA is currently registering one packet_type function per EtherType it
needs to intercept in the receive path of a DSA-enabled Ethernet device.
Right now we have three of them: trailer, DSA and eDSA, and there might
be more in the future, this will not scale to the addition of new
protocols.
This patch proceeds with adding a new layer of abstraction and two new
functions:
dsa_switch_rcv() which will dispatch into the tag-protocol specific
receive function implemented by net/dsa/tag_*.c
dsa_slave_xmit() which will dispatch into the tag-protocol specific
transmit function implemented by net/dsa/tag_*.c
When we do create the per-port slave network devices, we iterate over
the switch protocol to assign the DSA-specific receive and transmit
operations.
A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact
that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER
like it used to be.
This allows us to greatly simplify the check in eth_type_trans() and
always override the skb->protocol with ETH_P_XDSA for Ethernet switches
tagged protocol, while also reducing the number repetitive slave
netdevice_ops assignments.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.
Coccinelle patch:
@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@
(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)
v9: move comments here from the wrong commit
Signed-off-by: Tom Gundersen <teg@jklm.no>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: netdev@vger.kernel.org
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding more than one chip on device-tree currently causes the probing
routine to always use the first chips data pointer.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
