Age | Commit message (Collapse) | Author | Files | Lines |
|
Reducing real_num_tx_queues needs to be in sync with skb queue_mapping
otherwise skbs with queue_mapping greater than real_num_tx_queues
can be sent to the underlying driver and can result in kernel panic.
One such event is running netconsole and enabling VF on the same
device. Or running netconsole and changing number of tx queues via
ethtool on same device.
e.g.
Unable to handle kernel NULL pointer dereference
tsk->{mm,active_mm}->context = 0000000000001525
tsk->{mm,active_mm}->pgd = fff800130ff9a000
\|/ ____ \|/
"@'/ .. \`@"
/_| \__/ |_\
\__U_/
kworker/48:1(475): Oops [#1]
CPU: 48 PID: 475 Comm: kworker/48:1 Tainted: G OE
4.11.0-rc3-davem-net+ #7
Workqueue: events queue_process
task: fff80013113299c0 task.stack: fff800131132c000
TSTATE: 0000004480e01600 TPC: 00000000103f9e3c TNPC: 00000000103f9e40 Y:
00000000 Tainted: G OE
TPC: <ixgbe_xmit_frame_ring+0x7c/0x6c0 [ixgbe]>
g0: 0000000000000000 g1: 0000000000003fff g2: 0000000000000000 g3:
0000000000000001
g4: fff80013113299c0 g5: fff8001fa6808000 g6: fff800131132c000 g7:
00000000000000c0
o0: fff8001fa760c460 o1: fff8001311329a50 o2: fff8001fa7607504 o3:
0000000000000003
o4: fff8001f96e63a40 o5: fff8001311d77ec0 sp: fff800131132f0e1 ret_pc:
000000000049ed94
RPC: <set_next_entity+0x34/0xb80>
l0: 0000000000000000 l1: 0000000000000800 l2: 0000000000000000 l3:
0000000000000000
l4: 000b2aa30e34b10d l5: 0000000000000000 l6: 0000000000000000 l7:
fff8001fa7605028
i0: fff80013111a8a00 i1: fff80013155a0780 i2: 0000000000000000 i3:
0000000000000000
i4: 0000000000000000 i5: 0000000000100000 i6: fff800131132f1a1 i7:
00000000103fa4b0
I7: <ixgbe_xmit_frame+0x30/0xa0 [ixgbe]>
Call Trace:
[00000000103fa4b0] ixgbe_xmit_frame+0x30/0xa0 [ixgbe]
[0000000000998c74] netpoll_start_xmit+0xf4/0x200
[0000000000998e10] queue_process+0x90/0x160
[0000000000485fa8] process_one_work+0x188/0x480
[0000000000486410] worker_thread+0x170/0x4c0
[000000000048c6b8] kthread+0xd8/0x120
[0000000000406064] ret_from_fork+0x1c/0x2c
[0000000000000000] (null)
Disabling lock debugging due to kernel taint
Caller[00000000103fa4b0]: ixgbe_xmit_frame+0x30/0xa0 [ixgbe]
Caller[0000000000998c74]: netpoll_start_xmit+0xf4/0x200
Caller[0000000000998e10]: queue_process+0x90/0x160
Caller[0000000000485fa8]: process_one_work+0x188/0x480
Caller[0000000000486410]: worker_thread+0x170/0x4c0
Caller[000000000048c6b8]: kthread+0xd8/0x120
Caller[0000000000406064]: ret_from_fork+0x1c/0x2c
Caller[0000000000000000]: (null)
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-04-20
This adds the basic infrastructure for IPsec hardware
offloading, it creates a configuration API and adjusts
the packet path.
1) Add the needed netdev features to configure IPsec offloads.
2) Add the IPsec hardware offloading API.
3) Prepare the ESP packet path for hardware offloading.
4) Add gso handlers for esp4 and esp6, this implements
the software fallback for GSO packets.
5) Add xfrm replay handler functions for offloading.
6) Change ESP to use a synchronous crypto algorithm on
offloading, we don't have the option for asynchronous
returns when we handle IPsec at layer2.
7) Add a xfrm validate function to validate_xmit_skb. This
implements the software fallback for non GSO packets.
8) Set the inner_network and inner_transport members of
the SKB, as well as encapsulation, to reflect the actual
positions of these headers, and removes them only once
encryption is done on the payload.
From Ilan Tayari.
9) Prepare the ESP GRO codepath for hardware offloading.
10) Fix incorrect null pointer check in esp6.
From Colin Ian King.
11) Fix for the GSO software fallback path to detect the
fallback correctly.
From Ilan Tayari.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add napi_id access to __sk_buff for socket filter program types, tc
program types and other bpf_convert_ctx_access() users. Having access
to skb->napi_id is useful for per RX queue listener siloing, f.e.
in combination with SO_ATTACH_REUSEPORT_EBPF and when busy polling is
used, meaning SO_REUSEPORT enabled listeners can then select the
corresponding socket at SYN time already [1]. The skb is marked via
skb_mark_napi_id() early in the receive path (e.g., napi_gro_receive()).
Currently, sockets can only use SO_INCOMING_NAPI_ID from 6d4339028b35
("net: Introduce SO_INCOMING_NAPI_ID") as a socket option to look up
the NAPI ID associated with the queue for steering, which requires a
prior sk_mark_napi_id() after the socket was looked up.
Semantics for the __sk_buff napi_id access are similar, meaning if
skb->napi_id is < MIN_NAPI_ID (e.g. outgoing packets using sender_cpu),
then an invalid napi_id of 0 is returned to the program, otherwise a
valid non-zero napi_id.
[1] http://netdevconf.org/2.1/slides/apr6/dumazet-BUSY-POLLING-Netdev-2.1.pdf
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 07b26c9454a2 ("gso: Support partial splitting at the frag_list
pointer") assumes that all SKBs in a frag_list (except maybe the last
one) contain the same amount of GSO payload.
This assumption is not always correct, resulting in the following
warning message in the log:
skb_segment: too many frags
For example, mlx5 driver in Striding RQ mode creates some RX SKBs with
one frag, and some with 2 frags.
After GRO, the frag_list SKBs end up having different amounts of payload.
If this frag_list SKB is then forwarded, the aforementioned assumption
is violated.
Validate the assumption, and fall back to software GSO if it not true.
Change-Id: Ia03983f4a47b6534dd987d7a2aad96d54d46d212
Fixes: 07b26c9454a2 ("gso: Support partial splitting at the frag_list pointer")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Constants used for tuning are generally a bad idea, especially as hardware
changes over time. Replace the constant 2 jiffies with sysctl variable
netdev_budget_usecs to enable sysadmins to tune the softirq processing.
Also document the variable.
For example, a very fast machine might tune this to 1000 microseconds,
while my regression testing 486DX-25 needs it to be 4000 microseconds on
a nearly idle network to prevent time_squeeze from being incremented.
Version 2: changed jiffies to microseconds for predictable units.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct sock_filter_ext didn't make it into the tree and is now called
struct bpf_insn. Reword the kerneldoc comment for bpf_convert_filter()
accordingly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink_ext_ack arg to rtnl_doit_func. Pass extack arg to nlmsg_parse
for doit functions that call it directly.
This is the first step to using extended error reporting in rtnetlink.
>From here individual subsystems can be updated to set netlink_ext_ack as
needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 07b26c9454a2 ("gso: Support partial splitting at the frag_list
pointer") assumes that all SKBs in a frag_list (except maybe the last
one) contain the same amount of GSO payload.
This assumption is not always correct, resulting in the following
warning message in the log:
skb_segment: too many frags
For example, mlx5 driver in Striding RQ mode creates some RX SKBs with
one frag, and some with 2 frags.
After GRO, the frag_list SKBs end up having different amounts of payload.
If this frag_list SKB is then forwarded, the aforementioned assumption
is violated.
Validate the assumption, and fall back to software GSO if it not true.
Fixes: 07b26c9454a2 ("gso: Support partial splitting at the frag_list pointer")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BPF helper functions get_socket_cookie and get_socket_uid can be
used for network traffic classifications, among others. Expose
them also to programs of type BPF_PROG_TYPE_CGROUP_SKB. As of
commit 8f917bba0042 ("bpf: pass sk to helper functions") the
required skb->sk function is available at both cgroup bpf ingress
and egress hooks. With these two new helper, cg_skb_func_proto is
effectively the same as sk_filter_func_proto.
Change since V1:
Instead of add the helper to cg_skb_func_proto, redirect the
cg_skb_func_proto to sk_filter_func_proto since all helper function
in sk_filter_func_proto are applicable to cg_skb_func_proto now.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzkaller reported a use-after-free in ip_recv_error at line
info->ipi_ifindex = skb->dev->ifindex;
This function is called on dequeue from the error queue, at which
point the device pointer may no longer be valid.
Save ifindex on enqueue in __skb_complete_tx_timestamp, when the
pointer is valid or NULL. Store it in temporary storage skb->cb.
It is safe to reference skb->dev here, as called from device drivers
or dev_queue_xmit. The exception is when called from tcp_ack_tstamp;
in that case it is NULL and ifindex is set to 0 (invalid).
Do not return a pktinfo cmsg if ifindex is 0. This maintains the
current behavior of not returning a cmsg if skb->dev was NULL.
On dequeue, the ipv4 path will cast from sock_exterr_skb to
in_pktinfo. Both have ifindex as their first element, so no explicit
conversion is needed. This is by design, introduced in commit
0b922b7a829c ("net: original ingress device index in PKTINFO"). For
ipv6 ip6_datagram_support_cmsg converts to in6_pktinfo.
Fixes: 829ae9d61165 ("net-timestamp: allow reading recv cmsg on errqueue with origin tstamp")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If "scope_len" is sizeof(scope_id) then we would put the NUL terminator
one space beyond the end of the buffer.
Fixes: b1a951fe469e ("net/utils: generic inet_pton_with_scope helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When we do IPsec offloading, we need a fallback for
packets that were targeted to be IPsec offloaded but
rerouted to a device that does not support IPsec offload.
For that we add a function that checks the offloading
features of the sending device and and flags the
requirement of a fallback before it calls the IPsec
output function. The IPsec output function adds the IPsec
trailer and does encryption if needed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
This patch adds netdev features to configure IPsec offloads.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the base infrastructure and UAPI for netlink extended ACK
reporting. All "manual" calls to netlink_ack() pass NULL for now and
thus don't get extended ACK reporting.
Big thanks goes to Pablo Neira Ayuso for not only bringing up the
whole topic at netconf (again) but also coming up with the nlattr
passing trick and various other ideas.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing tx queue length generates identical messages:
[LINK]22: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 02:04:f4:b7:5c:d2 brd ff:ff:ff:ff:ff:ff promiscuity 0
dummy numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
[LINK]22: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 02:04:f4:b7:5c:d2 brd ff:ff:ff:ff:ff:ff promiscuity 0
dummy numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
Remove NETDEV_CHANGE_TX_QUEUE_LEN from the list of notifiers that generate
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NETDEV_CHANGEUPPER is an internal event; do not generate userspace
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CHANGELOWERSTATE is an internal event; do not generate userspace
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PRECHANGEUPPER is an internal event; do not generate userspace
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing the master device for a link generates many messages; the one
generated for POST_TYPE_CHANGE is redundant:
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master br1 state UNKNOWN group default
link/ether 02:02:02:02:02:03 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master br1 state UNKNOWN group default
link/ether 02:02:02:02:02:03 brd ff:ff:ff:ff:ff:ff
Remove POST_TYPE_CHANGE from the list of notifiers that generate
notifications.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing hardware address generates redundant messages:
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 02:02:02:02:02:02 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 02:02:02:02:02:02 brd ff:ff:ff:ff:ff:ff
Do not send a notification for the CHANGEADDR notifier.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NETDEV_UDP_TUNNEL_PUSH_INFO is an internal notifier; nothing userspace
can do so don't generate a netlink notification.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing MTU on a link currently causes 3 messages to be sent to userspace:
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1490 qdisc noqueue state UNKNOWN group default
link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff
Remove the messages sent for PRE_CHANGE_MTU and CHANGE_MTU netdev events.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A driver may use build_skb() for received packets.
These SKBs then have a head_frag.
Since commit d7e8883cfcf4 ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.
Commit 07b26c9454a2 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.
A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.
This causes low performance when forwarding those packets
that were built with build_skb()
Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.
Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev_change_xdp_fd() is only used in rtnetlink, which must
be built-in, there's no reason to export dev_change_xdp_fd().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.
Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the return value check which testing the wrong variable
in devlink_dpipe_header_put().
Fixes: 1555d204e743 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no need to have struct bpf_prog_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to a new
header file and include it in the places needing it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
current_restore_flags()
It is not safe for one thread to modify the ->flags
of another thread as there is no locking that can protect
the update.
So tsk_restore_flags(), which takes a task pointer and modifies
the flags, is an invitation to do the wrong thing.
All current users pass "current" as the task, so no developers have
accepted that invitation. It would be best to ensure it remains
that way.
So rename tsk_restore_flags() to current_restore_flags() and don't
pass in a task_struct pointer. Always operate on current->flags.
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This reverts commit def12888c161e6fec0702e5ec9c3962846e3a21d.
As per discussion between Roopa Prabhu and David Ahern, it is
advisable that we instead have the code collect the setlink triggered
events into a bitmask emitted in the IFLA_EVENT netlink attribute.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new getsockopt operation to retrieve the socket cookie
for a specific socket based on the socket fd. It returns a unique
non-decreasing cookie for each socket.
Tested: https://android-review.googlesource.com/#/c/358163/
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
|
|
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netdev events happen, a rtnetlink_event() handler will send
messages for every event in it's white list. These messages contain
current information about a particular device, but they do not include
the iformation about which event just happened. The consumer of
the message has to try to infer this information. In some cases
(ex: NETDEV_NOTIFY_PEERS), that is not possible.
This patch adds a new extension to RTM_NEWLINK message called IFLA_EVENT
that would have an encoding of the which event triggered this
message. This would allow the the message consumer to easily determine
if it is interested in a particular event or not.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtnetlink_event currently functions as a blacklist where
we block cerntain netdev events from being sent to user space.
As a result, events have been added to the system that userspace
probably doesn't care about.
This patch converts the implementation to the white list so that
newly events would have to be specifically added to the list to
be sent to userspace. This would force new event implementers to
consider whether a given event is usefull to user space or if it's
just a kernel event.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several locations in the stack need to handle ipv4/ipv6
(with scope) and port strings conversion to sockaddr.
Add a helper that takes either AF_INET, AF_INET6 or
AF_UNSPEC (for wildcard) to centralize this handling.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Number of sockets is limited by 16-bit, so 64-bit allocation will never
happen.
16-bit ops are the worst code density-wise on x86_64 because of
additional prefix (66).
Space savings:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-3 (-3)
function old new delta
reuseport_add_sock 539 536 -3
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make ->hash_count, ->low_watermark and ->high_watermark unsigned int
and propagate unsignedness to other variables.
This change doesn't change code generation because these fields aren't
used in 64-bit contexts but make it anyway: these fields can't be
negative numbers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hash size can't negative so "unsigned int" is logically correct.
Propagate "unsigned int" to loop counters.
Space savings:
add/remove: 0/0 grow/shrink: 2/2 up/down: 6/-18 (-12)
function old new delta
flow_cache_flush_tasklet 362 365 +3
__flow_cache_shrink 333 336 +3
flow_cache_cpu_up_prep 178 171 -7
flow_cache_lookup 1159 1148 -11
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flow keys aren't 4GB+ numbers so 64-bit arithmetic is excessive.
Space savings (I'm not sure what CSWTCH is):
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-48 (-48)
function old new delta
flow_cache_lookup 1163 1159 -4
CSWTCH 75997 75953 -44
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last argument to __skb_header_pointer() should be a buffer large
enough to store struct arphdr. This can be a pointer to a struct arphdr
structure. The code was previously using a pointer to a pointer to
struct arphdr.
By my counting the storage available both before and after is 8 bytes on
x86_64.
Fixes: 55733350e5e8 ("flow disector: ARP support")
Reported-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the mess observed in e.g. rsync over a noisy link we'd been
seeing since last Summer. What happens is that we copy part of
a datagram before noticing a checksum mismatch. Datagram will be
resent, all right, but we want the next try go into the same place,
not after it...
All this family of primitives (copy/checksum and copy a datagram
into destination) is "all or nothing" sort of interface - either
we get 0 (meaning that copy had been successful) or we get an
error (and no way to tell how much had been copied before we ran
into whatever error it had been). Make all of them leave iterator
unadvanced in case of errors - all callers must be able to cope
with that (an error might've been caught before the iterator had
been advanced), it costs very little to arrange, it's safer for
callers and actually fixes at least one bug in said callers.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
development and testing of networking bpf programs is quite cumbersome.
Despite availability of user space bpf interpreters the kernel is
the ultimate authority and execution environment.
Current test frameworks for TC include creation of netns, veth,
qdiscs and use of various packet generators just to test functionality
of a bpf program. XDP testing is even more complicated, since
qemu needs to be started with gro/gso disabled and precise queue
configuration, transferring of xdp program from host into guest,
attaching to virtio/eth0 and generating traffic from the host
while capturing the results from the guest.
Moreover analyzing performance bottlenecks in XDP program is
impossible in virtio environment, since cost of running the program
is tiny comparing to the overhead of virtio packet processing,
so performance testing can only be done on physical nic
with another server generating traffic.
Furthermore ongoing changes to user space control plane of production
applications cannot be run on the test servers leaving bpf programs
stubbed out for testing.
Last but not least, the upstream llvm changes are validated by the bpf
backend testsuite which has no ability to test the code generated.
To improve this situation introduce BPF_PROG_TEST_RUN command
to test and performance benchmark bpf programs.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sock_recv_ts_and_drops() unconditionally set sk->sk_stamp for
every packet, even if the SOCK_TIMESTAMP flag is not set in the
related socket.
If selinux is enabled, this cause a cache miss for every packet
since sk->sk_stamp and sk->sk_security share the same cacheline.
With this change sk_stamp is set only if the SOCK_TIMESTAMP
flag is set, and is cleared for the first packet, so that the user
perceived behavior is unchanged.
This gives up to 5% speed-up under udp-flood with small packets.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pipeline debug is used to export the pipeline abstractions for the
main objects - tables, headers and entries. The only support for set is
for changing the counter parameter on specific table.
The basic structures:
Header - can represent a real protocol header information or internal
metadata. Generic protocol headers like IPv4 can be shared
between drivers. Each driver can add local headers.
Field - part of a header. Can represent protocol field or specific ASIC
metadata field. Hardware special metadata fields can be mapped
to different resources, for example switch ASIC ports can have
internal number which from the systems point of view is mapped
to netdeivce ifindex.
Match - represent specific match rule. Can describe match on specific
field or header. The header index should be specified as well
in order to support several header instances of the same type
(tunneling).
Action - represents specific action rule. Actions can describe operations
on specific field values for example like set, increment, etc.
And header operation like add and delete.
Value - represents value which can be associated with specific match or
action.
Table - represents a hardware block which can be described with match/
action behavior. The match/action can be done on the packets
data or on the internal metadata that it gathered along the
packets traversal throw the pipeline which is vendor specific
and should be exported in order to provide understanding of
ASICs behavior.
Entry - represents single record in a specific table. The entry is
identified by specific combination of values for match/action.
Prior to accessing the tables/entries the drivers provide the header/
field data base which is used by driver to user-space. The data base
is split between the shared headers and unique headers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This socket option returns the NAPI ID associated with the queue on which
the last frame is received. This information can be used by the apps to
split the incoming flows among the threads based on the Rx queue on which
they are received.
If the NAPI ID actually represents a sender_cpu then the value is ignored
and 0 is returned.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|