summaryrefslogtreecommitdiffstats
path: root/net/batman-adv
AgeCommit message (Collapse)AuthorFilesLines
2018-04-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2-3/+6
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c, we had some overlapping changes: 1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE --> MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE 2) In 'net-next' params->log_rq_size is renamed to be params->log_rq_mtu_frames. 3) In 'net-next' params->hard_mtu is added. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-24batman-adv: fix packet loss for broadcasted DHCP packets to a serverLinus Lüssing1-1/+4
DHCP connectivity issues can currently occur if the following conditions are met: 1) A DHCP packet from a client to a server 2) This packet has a multicast destination 3) This destination has a matching entry in the translation table (FF:FF:FF:FF:FF:FF for IPv4, 33:33:00:01:00:02/33:33:00:01:00:03 for IPv6) 4) The orig-node determined by TT for the multicast destination does not match the orig-node determined by best-gateway-selection In this case the DHCP packet will be dropped. The "gateway-out-of-range" check is supposed to only be applied to unicasted DHCP packets to a specific DHCP server. In that case dropping the the unicasted frame forces the client to retry via a broadcasted one, but now directed to the new best gateway. A DHCP packet with broadcast/multicast destination is already ensured to always be delivered to the best gateway. Dropping a multicasted DHCP packet here will only prevent completing DHCP as there is no other fallback. So far, it seems the unicast check was implicitly performed by expecting the batadv_transtable_search() to return NULL for multicast destinations. However, a multicast address could have always ended up in the translation table and in fact is now common. To fix this potential loss of a DHCP client-to-server packet to a multicast address this patch adds an explicit multicast destination check to reliably bail out of the gateway-out-of-range check for such destinations. The issue and fix were tested in the following three node setup: - Line topology, A-B-C - A: gateway client, DHCP client - B: gateway server, hop-penalty increased: 30->60, DHCP server - C: gateway server, code modifications to announce FF:FF:FF:FF:FF:FF Without this patch, A would never transmit its DHCP Discover packet due to an always "out-of-range" condition. With this patch, a full DHCP handshake between A and B was possible again. Fixes: be7af5cf9cae ("batman-adv: refactoring gateway handling code") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-24batman-adv: fix multicast-via-unicast transmission with AP isolationLinus Lüssing1-2/+2
For multicast frames AP isolation is only supposed to be checked on the receiving nodes and never on the originating one. Furthermore, the isolation or wifi flag bits should only be intepreted as such for unicast and never multicast TT entries. By injecting flags to the multicast TT entry claimed by a single target node it was verified in tests that this multicast address becomes unreachable, leading to packet loss. Omitting the "src" parameter to the batadv_transtable_search() call successfully skipped the AP isolation check and made the target reachable again. Fixes: 1d8ab8d3c176 ("batman-adv: Modified forwarding behaviour for multicast packets") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller5-13/+20
Fun set of conflict resolutions here... For the mac80211 stuff, these were fortunately just parallel adds. Trivially resolved. In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the function phy_disable_interrupts() earlier in the file, whilst in 'net-next' the phy_error() call from this function was removed. In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the 'rt_table_id' member of rtable collided with a bug fix in 'net' that added a new struct member "rt_mtu_locked" which needs to be copied over here. The mlxsw driver conflict consisted of net-next separating the span code and definitions into separate files, whilst a 'net' bug fix made some changes to that moved code. The mlx5 infiniband conflict resolution was quite non-trivial, the RDMA tree's merge commit was used as a guide here, and here are their notes: ==================== Due to bug fixes found by the syzkaller bot and taken into the for-rc branch after development for the 4.17 merge window had already started being taken into the for-next branch, there were fairly non-trivial merge issues that would need to be resolved between the for-rc branch and the for-next branch. This merge resolves those conflicts and provides a unified base upon which ongoing development for 4.17 can be based. Conflicts: drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f9524 (IB/mlx5: Fix cleanup order on unload) added to for-rc and commit b5ca15ad7e61 (IB/mlx5: Add proper representors support) add as part of the devel cycle both needed to modify the init/de-init functions used by mlx5. To support the new representors, the new functions added by the cleanup patch needed to be made non-static, and the init/de-init list added by the representors patch needed to be modified to match the init/de-init list changes made by the cleanup patch. Updates: drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function prototypes added by representors patch to reflect new function names as changed by cleanup patch drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init stage list to match new order from cleanup patch ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-22Merge tag 'batadv-next-for-davem-20180319' of ↵David S. Miller5-37/+522
git://git.open-mesh.org/linux-merge Simon Wunderlich says: ==================== This feature/cleanup patchset includes the following patches: - avoid redundant multicast TT entries, by Linus Luessing - add netlink support for distributed arp table cache and multicast flags, by Linus Luessing (2 patches) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-18batman-adv: Fix skbuff rcsum on packet rerouteSven Eckelmann1-5/+10
batadv_check_unicast_ttvn may redirect a packet to itself or another originator. This involves rewriting the ttvn and the destination address in the batadv unicast header. These field were not yet pulled (with skb rcsum update) and thus any change to them also requires a change in the receive checksum. Reported-by: Matthias Schiffer <mschiffer@universe-factory.net> Fixes: a73105b8d4c7 ("batman-adv: improved client announcement mechanism") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-18batman-adv: Add missing include for EPOLL* constantsSven Eckelmann2-0/+2
Fixes: a9a08845e9ac ("vfs: do bulk POLL* -> EPOLL* replacement") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-16batman-adv: fix header size check in batadv_dbg_arp()Matthias Schiffer1-1/+1
Checking for 0 is insufficient: when an SKB without a batadv header, but with a VLAN header is received, hdr_size will be 4, making the following code interpret the Ethernet header as a batadv header. Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-16batman-adv: update data pointers after skb_cow()Matthias Schiffer1-5/+5
batadv_check_unicast_ttvn() calls skb_cow(), so pointers into the SKB data must be (re)set after calling it. The ethhdr variable is dropped altogether. Fixes: 7cdcf6dddc42 ("batman-adv: add UNICAST_4ADDR packet type") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-14batman-adv: add multicast flags netlink supportLinus Lüssing3-0/+267
Dump the list of multicast flags entries via the netlink socket. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-14batman-adv: add DAT cache netlink supportLinus Lüssing3-33/+203
Dump the list of DAT cache entries via the netlink socket. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller9-39/+50
All of the conflicts were cases of overlapping changes. In net/core/devlink.c, we have to make care that the resouce size_params have become a struct member rather than a pointer to such an object. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-04batman-adv: Avoid redundant multicast TT entriesLinus Lüssing1-4/+52
If a node signals that it wants all traffic for a specific protocol family then there is no need to announce individual multicast addresses via TT. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-03-04batman-adv: Fix multicast packet loss with a single WANT_ALL_IPV4/6 flagLinus Lüssing1-2/+2
As the kernel doc describes too the code is supposed to skip adding multicast TT entries if both the WANT_ALL_IPV4 and WANT_ALL_IPV6 flags are present. Unfortunately, the current code even skips adding multicast TT entries if only either the WANT_ALL_IPV4 or WANT_ALL_IPV6 is present. This could lead to IPv6 multicast packet loss if only an IGMP but not an MLD querier is present for instance or vice versa. Fixes: 687937ab3489 ("batman-adv: Add multicast optimization support for bridged setups") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-27batman-adv: Avoid relation operator comparison with boolSven Eckelmann1-1/+1
commit 785ea1144182 ("batman-adv: Distributed ARP Table - create DHT helper functions") introduced a return check of batadv_compare_eth which uses a boolean return value since commit 16af73458aca ("batman-adv: main, batadv_compare_eth return bool"). A relational (<, >, <= or >=) operator is not the right one for such a check. Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-27batman-adv: Fix indentation of batadv_seq_beforeSven Eckelmann1-5/+7
Also multiline macros should have their statements start on a tabstop. This was detected by checkpatch.pl after commit a134f8de9f40 ("checkpatch: improve the TABSTOP test to include declarations"). Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-26batman-adv: Update copyright years for 2018Sven Eckelmann59-59/+59
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-26batman-adv: Start new development cycleSimon Wunderlich1-1/+1
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Fix internal interface indices typesSven Eckelmann5-21/+31
batman-adv uses internal indices for each enabled and active interface. It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the correct position in the ogm_cnt bitmaps. The type for the number of enabled interfaces (which defines the next interface index) was set to char. This type can be (depending on the architecture) either signed (limiting batman-adv to 127 active slave interfaces) or unsigned (limiting batman-adv to 255 active slave interfaces). This limit was not correctly checked when an interface was enabled and thus an overflow happened. This was only catched on systems with the signed char type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with a negative size. The if_num interface index was only a s16 and therefore significantly smaller than the ifindex (int) used by the code net code. Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be (unsigned) int to support the same number of slave interfaces as the net core code. And the interface activation code must check the number of active slave interfaces to avoid integer overflows. Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Fix netlink dumping of BLA backbonesSven Eckelmann1-4/+7
The function batadv_bla_backbone_dump_bucket must be able to handle non-complete dumps of a single bucket. It tries to do that by saving the latest dumped index in *idx_skip to inform the caller about the current state. But the caller only assumes that buckets were not completely dumped when the return code is non-zero. This function must therefore also return a non-zero index when the dumping of an entry failed. Otherwise the caller will just skip all remaining buckets. And the function must also reset *idx_skip back to zero when it finished a bucket. Otherwise it will skip the same number of entries in the next bucket as the previous one had. Fixes: ea4152e11716 ("batman-adv: add backbone table netlink support") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Fix netlink dumping of BLA claimsSven Eckelmann1-4/+7
The function batadv_bla_claim_dump_bucket must be able to handle non-complete dumps of a single bucket. It tries to do that by saving the latest dumped index in *idx_skip to inform the caller about the current state. But the caller only assumes that buckets were not completely dumped when the return code is non-zero. This function must therefore also return a non-zero index when the dumping of an entry failed. Otherwise the caller will just skip all remaining buckets. And the function must also reset *idx_skip back to zero when it finished a bucket. Otherwise it will skip the same number of entries in the next bucket as the previous one had. Fixes: 04f3f5bf1883 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Ignore invalid batadv_v_gw during netlink sendSven Eckelmann1-1/+1
The function batadv_v_gw_dump stops the processing loop when batadv_v_gw_dump_entry returns a non-0 return code. This should only happen when the buffer is full. Otherwise, an empty message may be returned by batadv_gw_dump. This empty message will then stop the netlink dumping of gateway entries. At worst, not a single entry is returned to userspace even when plenty of possible gateways exist. Fixes: b71bb6f924fe ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Ignore invalid batadv_iv_gw during netlink sendSven Eckelmann1-1/+1
The function batadv_iv_gw_dump stops the processing loop when batadv_iv_gw_dump_entry returns a non-0 return code. This should only happen when the buffer is full. Otherwise, an empty message may be returned by batadv_gw_dump. This empty message will then stop the netlink dumping of gateway entries. At worst, not a single entry is returned to userspace even when plenty of possible gateways exist. Fixes: efb766af06e3 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: invalidate checksum on fragment reassemblyMatthias Schiffer1-1/+2
A more sophisticated implementation could try to combine fragment checksums when all fragments have CHECKSUM_COMPLETE and are split at even offsets. For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure" warnings in the kernel log when fragmented frames are received. In consequence, skb_pull_rcsum() can be replaced with skb_pull(). Note that in usual setups, packets don't reach batman-adv with CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see batadv's ethtype?), which is why the log messages do not occur on every system using batman-adv. I could reproduce this issue by stacking batman-adv on top of a VXLAN interface. Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: fix packet checksum in receive pathMatthias Schiffer1-7/+1
eth_type_trans() internally calls skb_pull(), which does not adjust the skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are received. Note that in usual setups, packets don't reach batman-adv with CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see batadv's ethtype?), which is why the log messages do not occur on every system using batman-adv. I could reproduce this issue by stacking batman-adv on top of a VXLAN interface. Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-11vfs: do bulk POLL* -> EPOLL* replacementLinus Torvalds2-2/+2
This is the mindless scripted replacement of kernel use of POLL* variables as described by Al, done by this script: for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done done with de-mangling cleanups yet to come. NOTE! On almost all architectures, the EPOLL* constants have the same values as the POLL* constants do. But they keyword here is "almost". For various bad reasons they aren't the same, and epoll() doesn't actually work quite correctly in some cases due to this on Sparc et al. The next patch from Al will sort out the final differences, and we should be all done. Scripted-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds60-1990/+2833
Pull networking updates from David Miller: 1) Significantly shrink the core networking routing structures. Result of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf 2) Add netdevsim driver for testing various offloads, from Jakub Kicinski. 3) Support cross-chip FDB operations in DSA, from Vivien Didelot. 4) Add a 2nd listener hash table for TCP, similar to what was done for UDP. From Martin KaFai Lau. 5) Add eBPF based queue selection to tun, from Jason Wang. 6) Lockless qdisc support, from John Fastabend. 7) SCTP stream interleave support, from Xin Long. 8) Smoother TCP receive autotuning, from Eric Dumazet. 9) Lots of erspan tunneling enhancements, from William Tu. 10) Add true function call support to BPF, from Alexei Starovoitov. 11) Add explicit support for GRO HW offloading, from Michael Chan. 12) Support extack generation in more netlink subsystems. From Alexander Aring, Quentin Monnet, and Jakub Kicinski. 13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From Russell King. 14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso. 15) Many improvements and simplifications to the NFP driver bpf JIT, from Jakub Kicinski. 16) Support for ipv6 non-equal cost multipath routing, from Ido Schimmel. 17) Add resource abstration to devlink, from Arkadi Sharshevsky. 18) Packet scheduler classifier shared filter block support, from Jiri Pirko. 19) Avoid locking in act_csum, from Davide Caratti. 20) devinet_ioctl() simplifications from Al viro. 21) More TCP bpf improvements from Lawrence Brakmo. 22) Add support for onlink ipv6 route flag, similar to ipv4, from David Ahern. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits) tls: Add support for encryption using async offload accelerator ip6mr: fix stale iterator net/sched: kconfig: Remove blank help texts openvswitch: meter: Use 64-bit arithmetic instead of 32-bit tcp_nv: fix potential integer overflow in tcpnv_acked r8169: fix RTL8168EP take too long to complete driver initialization. qmi_wwan: Add support for Quectel EP06 rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK ipmr: Fix ptrdiff_t print formatting ibmvnic: Wait for device response when changing MAC qlcnic: fix deadlock bug tcp: release sk_frag.page in tcp_disconnect ipv4: Get the address of interface correctly. net_sched: gen_estimator: fix lockdep splat net: macb: Handle HRESP error net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring ipv6: addrconf: break critical section in addrconf_verify_rtnl() ipv6: change route cache aging logic i40e/i40evf: Update DESC_NEEDED value to reflect larger value bnxt_en: cleanup DIM work on device shutdown ...
2018-01-30Merge branch 'misc.poll' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull poll annotations from Al Viro: "This introduces a __bitwise type for POLL### bitmap, and propagates the annotations through the tree. Most of that stuff is as simple as 'make ->poll() instances return __poll_t and do the same to local variables used to hold the future return value'. Some of the obvious brainos found in process are fixed (e.g. POLLIN misspelled as POLL_IN). At that point the amount of sparse warnings is low and most of them are for genuine bugs - e.g. ->poll() instance deciding to return -EINVAL instead of a bitmap. I hadn't touched those in this series - it's large enough as it is. Another problem it has caught was eventpoll() ABI mess; select.c and eventpoll.c assumed that corresponding POLL### and EPOLL### were equal. That's true for some, but not all of them - EPOLL### are arch-independent, but POLL### are not. The last commit in this series separates userland POLL### values from the (now arch-independent) kernel-side ones, converting between them in the few places where they are copied to/from userland. AFAICS, this is the least disruptive fix preserving poll(2) ABI and making epoll() work on all architectures. As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and it will trigger only on what would've triggered EPOLLWRBAND on other architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered at all on sparc. With this patch they should work consistently on all architectures" * 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits) make kernel-side POLL... arch-independent eventpoll: no need to mask the result of epi_item_poll() again eventpoll: constify struct epoll_event pointers debugging printk in sg_poll() uses %x to print POLL... bitmap annotate poll(2) guts 9p: untangle ->poll() mess ->si_band gets POLL... bitmap stored into a user-visible long field ring_buffer_poll_wait() return value used as return value of ->poll() the rest of drivers/*: annotate ->poll() instances media: annotate ->poll() instances fs: annotate ->poll() instances ipc, kernel, mm: annotate ->poll() instances net: annotate ->poll() instances apparmor: annotate ->poll() instances tomoyo: annotate ->poll() instances sound: annotate ->poll() instances acpi: annotate ->poll() instances crypto: annotate ->poll() instances block: annotate ->poll() instances x86: annotate ->poll() instances ...
2017-12-21batman-adv: Convert packet.h to uapi headerSven Eckelmann25-670/+24
The header file is used by different userspace programs to inject packets or to decode sniffed packets. It should therefore be available to them as userspace header. Also other components in the kernel (like the flow dissector) require access to the packet definitions to be able to decode ETH_P_BATMAN ethernet packets. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-21batman-adv: Remove kernel fixed width types in packet.hSven Eckelmann1-107/+107
The uapi headers use the __u8/__u16/... version of the fixed width types instead of u8/u16/... The use of the latter must be avoided before packet.h is copied to include/uapi/linux/. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-21batman-adv: Remove usage of BIT(x) in packet.hSven Eckelmann1-12/+11
The BIT(x) macro is no longer available for uapi headers because it is defined outside of it (linux/bitops.h). The use of it must therefore be avoided and replaced by an appropriate other representation. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-21batman-adv: Let packet.h include its headers directlySven Eckelmann2-2/+2
The headers used by packet.h should also be included by it directly. main.h is currently dealing with it in batman-adv, but this will no longer work when this header is moved to include/uapi/linux/. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-20Merge tag 'batadv-next-for-davem-20171220' of ↵David S. Miller60-1343/+2833
git://git.open-mesh.org/linux-merge Simon Wunderlich says: ==================== This feature/cleanup patchset includes the following patches: - bump version strings, by Simon Wunderlich - de-inline hash functions to save memory footprint, by Denys Vlasenko - Add License information to various files, by Sven Eckelmann (3 patches) - Change batman_adv.h from ISC to MIT, by Sven Eckelmann - Improve various includes, by Sven Eckelmann (5 patches) - Lots of kernel-doc work by Sven Eckelmann (8 patches) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-15batman-adv: Add kernel-doc to externally visible functionsSven Eckelmann16-3/+381
According to the kernel-doc documentation, externally visible functions should be documented. This refers to all all non-static function which can (and will) be used by functions in other sources files. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Add kernel-doc to functions in headersSven Eckelmann6-19/+131
Externally visible functions should be documented with kernel-doc. This usually refers to non-static functions but also static inline files in headers are visible in other files and should therefore be documented. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Add kernel-doc to enums in headersSven Eckelmann2-0/+55
All enums in types.h are already documented. But some other headers still have private enums which also should be documented. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Add kernel-doc to structs in headersSven Eckelmann2-3/+24
All structs in types.h are already documented. But some other headers still have private structs which also should be documented. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Fix kernel-doc references to struct membersSven Eckelmann1-23/+26
The correct syntax to create references in kernel-doc to a struct member is not "struct_name::member"" but "&struct_name->member" or "&struct_name.member". The correct syntax is required to get the correct cross-referencing in the reStructuredText text output. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Use inline kernel-doc for enum/structSven Eckelmann6-636/+1444
The inline kernel-doc comments make it easier to keep changes to the struct/enum synchronized with the documentation of the it. And it makes it easier for larger structures like struct batadv_priv to read the documentation inside the code. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Use parentheses in function kernel-docSven Eckelmann34-619/+633
The documentation describing kernel-doc comments for functions ("How to format kernel-doc comments") uses parentheses at the end of the function name. Using this format allows to use a consistent style when adding documentation to a function and when referencing this function in a different kernel-doc section. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Add missing kernel-doc to packet.hSven Eckelmann1-2/+23
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Remove unused sched.h includeSven Eckelmann1-1/+0
The linux/wait.h include was removed with commit 421d988b2c08 ("batman-adv: Consolidate logging related functions"). The previously required (but not unused) linux/sched.h include can also be dropped now. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: include kobject.h for kobject_* functionsSven Eckelmann1-0/+1
The linux/kobject.h provides the kobject_* function declarations and should therefore be included directly before they are used. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Include net.h for net_ratelimited_functionSven Eckelmann2-0/+2
The linux/net.h provides the net_ratelimited_function. It should therefore be included directly before it is used. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: include build_bug.h for BUILD_BUG_ON defineSven Eckelmann3-3/+3
commit bc6245e5efd7 ("bug: split BUILD_BUG stuff out into <linux/build_bug.h>") added a new header for BUILD_BUG_ON. It should therefore be included instead of linux/bug.h Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: include gfp.h for GFP_* definesSven Eckelmann22-20/+22
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should therefore be included instead of linux/fs.h. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Add license header to KconfigSven Eckelmann1-0/+17
The last remaining file without license notice and/or SPDX license identifier under net/batman-adv/ is the Kconfig. It should have been licensed under the same conditions as the rest of batman-adv and the Makefile which uses the CONFIG_* variables from Kconfig. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-15batman-adv: Add SPDX license identifier above copyright headerSven Eckelmann59-1/+59
The "Linux kernel licensing rules" require that each file has a SPDX license identifier as first line (and sometimes as second line). The FSFE REUSE practices [1] would also require the same tags but have no restrictions on the placement in the source file. Using the "Linux kernel licensing rules" is therefore also fulfilling the FSFE REUSE practices requirements at the same time. [1] https://reuse.software/practices/ Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-04batman-adv: Deinline batadv_orig_hash_find, save 7339 bytesDenys Vlasenko2-35/+34
This function compiles to 288 bytes of machine code for Linux 4.14 on Debian Stretch amd64 and (6.3.0-18) with the default configuration. 27 callsites (25 used in default config). text data bss dec hex filename 179291 10317 4416 194024 2f5e8 batman-adv.ko.pre 171952 10317 4416 186685 2d93d batman-adv.ko.post Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> [sven@narfation.org: Fix includes, correct sizes+counts in commit message] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2017-12-04batman-adv: Start new development cycleSimon Wunderlich1-1/+1
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>