| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
powerpc and x86 were opencoding copies of setup_nr_node_ids(), which
page_alloc provides but makes static. Make it avaliable to the archs in
linux/mm.h.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When booting on a large memory system, the kernel spends considerable
time in memmap_init_zone() setting up memory zones. Analysis shows
significant time spent in __early_pfn_to_nid().
The routine memmap_init_zone() checks each PFN to verify the nid is
valid. __early_pfn_to_nid() sequentially scans the list of pfn ranges
to find the right range and returns the nid. This does not scale well.
On a 4 TB (single rack) system there are 308 memory ranges to scan. The
higher the PFN the more time spent sequentially spinning through memory
ranges.
Since memmap_init_zone() increments pfn, it will almost always be
looking for the same range as the previous pfn, so check that range
first. If it is in the same range, return that nid. If not, scan the
list as before.
A 4 TB (single rack) UV1 system takes 512 seconds to get through the
zone code. This performance optimization reduces the time by 189
seconds, a 36% improvement.
A 2 TB (single rack) UV2 system goes from 212.7 seconds to 99.8 seconds,
a 112.9 second (53%) reduction.
[akpm@linux-foundation.org: make the statics __meminitdata]
[akpm@linux-foundation.org: fix comment formatting]
[akpm@linux-foundation.org: fix ia64, per yinghai]
[akpm@linux-foundation.org: add missing semicolon, per Tony]
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Tested-by: "Luck, Tony" <tony.luck@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Lin Feng <linfeng@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following problem was reported against a distribution kernel when
zone_reclaim was enabled but the same problem applies to the mainline
kernel. The reproduction case was as follows
1. Run numactl -m +0 dd if=largefile of=/dev/null
This allocates a large number of clean pages in node 0
2. numactl -N +0 memhog 0.5*Mg
This start a memory-using application in node 0.
The expected behaviour is that the clean pages get reclaimed and the
application uses node 0 for its memory. The observed behaviour was that
the memory for the memhog application was allocated off-node since
commits cd38b115d5ad ("mm: page allocator: initialise ZLC for first zone
eligible for zone_reclaim") and commit 76d3fbf8fbf6 ("mm: page
allocator: reconsider zones for allocation after direct reclaim").
The assumption of those patches was that it was always preferable to
allocate quickly than stall for long periods of time and they were meant
to take care that the zone was only marked full when necessary but an
important case was missed.
In the allocator fast path, only the low watermarks are checked. If the
zones free pages are between the low and min watermark then allocations
from the allocators slow path will succeed. However, zone_reclaim will
only reclaim SWAP_CLUSTER_MAX or 1<<order pages. There is no guarantee
that this will meet the low watermark causing the zone to be marked full
prematurely.
This patch will only mark the zone full after zone_reclaim if it the min
watermarks are checked or if page reclaim failed to make sufficient
progress.
[mhocko@suse.cz: fix alloc_flags test]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Hedi Berriche <hedi@sgi.com>
Tested-by: Hedi Berriche <hedi@sgi.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Particularly in oom conditions, it's troublesome that hugetlb memory is
not displayed. All other meminfo that is emitted will not add up to
what is expected, and there is no artifact left in the kernel log to
show that a potentially significant amount of memory is actually
allocated as hugepages which are not available to be reclaimed.
Booting with hugepages=8192 on the command line, this memory is now
shown in oom conditions. For example, with echo m >
/proc/sysrq-trigger:
Node 0 hugepages_total=2048 hugepages_free=2048 hugepages_surp=0 hugepages_size=2048kB
Node 1 hugepages_total=2048 hugepages_free=2048 hugepages_surp=0 hugepages_size=2048kB
Node 2 hugepages_total=2048 hugepages_free=2048 hugepages_surp=0 hugepages_size=2048kB
Node 3 hugepages_total=2048 hugepages_free=2048 hugepages_surp=0 hugepages_size=2048kB
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The original goal of this patchset is to fix the bug reported by
https://bugzilla.kernel.org/show_bug.cgi?id=53501
Now it has also been expanded to reduce common code used by memory
initializion.
This is the second part, which applies to the previous part at:
http://marc.info/?l=linux-mm&m=136289696323825&w=2
It introduces a helper function free_highmem_page() to free highmem
pages into the buddy system when initializing mm subsystem.
Introduction of free_highmem_page() is one step forward to clean up
accesses and modificaitons of totalhigh_pages, totalram_pages and
zone->managed_pages etc. I hope we could remove all references to
totalhigh_pages from the arch/ subdirectory.
We have only tested these patchset on x86 platforms, and have done basic
compliation tests using cross-compilers from ftp.kernel.org. That means
some code may not pass compilation on some architectures. So any help
to test this patchset are welcomed!
There are several other parts still under development:
Part3: refine code to manage totalram_pages, totalhigh_pages and
zone->managed_pages
Part4: introduce helper functions to simplify mem_init() and remove the
global variable num_physpages.
This patch:
Introduce helper function free_highmem_page(), which will be used by
architectures with HIGHMEM enabled to free highmem pages into the buddy
system.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Suzuki K. Poulose" <suzuki@in.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Attilio Rao <attilio.rao@citrix.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Cong Wang <amwang@redhat.com>
Cc: David Daney <david.daney@cavium.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rik van Riel <riel@redhat.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The original goal of this patchset is to fix the bug reported by
https://bugzilla.kernel.org/show_bug.cgi?id=53501
Now it has also been expanded to reduce common code used by memory
initializion.
This is the first part, which applies to v3.9-rc1.
It introduces following common helper functions to simplify
free_initmem() and free_initrd_mem() on different architectures:
adjust_managed_page_count():
will be used to adjust totalram_pages, totalhigh_pages,
zone->managed_pages when reserving/unresering a page.
__free_reserved_page():
free a reserved page into the buddy system without adjusting
page statistics info
free_reserved_page():
free a reserved page into the buddy system and adjust page
statistics info
mark_page_reserved():
mark a page as reserved and adjust page statistics info
free_reserved_area():
free a continous ranges of pages by calling free_reserved_page()
free_initmem_default():
default method to free __init pages.
We have only tested these patchset on x86 platforms, and have done basic
compliation tests using cross-compilers from ftp.kernel.org. That means
some code may not pass compilation on some architectures. So any help to
test this patchset are welcomed!
There are several other parts still under development:
Part2: introduce free_highmem_page() to simplify freeing highmem pages
Part3: refine code to manage totalram_pages, totalhigh_pages and
zone->managed_pages
Part4: introduce helper functions to simplify mem_init() and remove the
global variable num_physpages.
This patch:
Code to deal with reserved/managed pages are duplicated by many
architectures, so introduce common help functions to reduce duplicated
code. These common help functions will also be used to concentrate code
to modify totalram_pages and zone->managed_pages, which makes the code
much more clear.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On large systems with a lot of memory, walking all RAM to determine page
types may take a half second or even more.
In non-blockable contexts, the page allocator will emit a page allocation
failure warning unless __GFP_NOWARN is specified. In such contexts, irqs
are typically disabled and such a lengthy delay may even result in NMI
watchdog timeouts.
To fix this, suppress the page walk in such contexts when printing the
page allocation failure warning.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This symbol will be used in the Hyper-V balloon driver to support 2M
allocations.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tim found:
WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
Hardware name: S2600CP
sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
smpboot: Booting Node 1, Processors #1
Modules linked in:
Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
Call Trace:
set_cpu_sibling_map+0x279/0x449
start_secondary+0x11d/0x1e5
Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d195525809 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")
It turns out movable_map has some problems, and it breaks several things
1. numa_init is called several times, NOT just for srat. so those
nodes_clear(numa_nodes_parsed)
memset(&numa_meminfo, 0, sizeof(numa_meminfo))
can not be just removed. Need to consider sequence is: numaq, srat, amd, dummy.
and make fall back path working.
2. simply split acpi_numa_init to early_parse_srat.
a. that early_parse_srat is NOT called for ia64, so you break ia64.
b. for (i = 0; i < MAX_LOCAL_APIC; i++)
set_apicid_to_node(i, NUMA_NO_NODE)
still left in numa_init. So it will just clear result from early_parse_srat.
it should be moved before that....
c. it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
early before override from INITRD is settled.
3. that patch TITLE is total misleading, there is NO x86 in the title,
but it changes critical x86 code. It caused x86 guys did not
pay attention to find the problem early. Those patches really should
be routed via tip/x86/mm.
4. after that commit, following range can not use movable ram:
a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
b. initrd... it will be freed after booting, so it could be on movable...
c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
anymore.
d. init_mem_mapping: can not put page table high anymore.
e. initmem_init: vmemmap can not be high local node anymore. That is
not good.
If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.
We have workaround patch that could fix some problems, but some can not
be fixed.
So just remove that offending commit and related ones including:
f7210e6c4ac7 ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
protect movablecore_map in memblock_overlaps_region().")
01a178a94e8e ("acpi, memory-hotplug: support getting hotplug info from
SRAT")
27168d38fa20 ("acpi, memory-hotplug: extend movablemem_map ranges to
the end of node")
e8d195525809 ("acpi, memory-hotplug: parse SRAT before memblock is
ready")
fb06bc8e5f42 ("page_alloc: bootmem limit with movablecore_map")
42f47e27e761 ("page_alloc: make movablemem_map have higher priority")
6981ec31146c ("page_alloc: introduce zone_movable_limit[] to keep
movable limit for nodes")
34b71f1e04fc ("page_alloc: add movable_memmap kernel parameter")
4d59a75125d5 ("x86: get pg_data_t's memory from other node")
Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0. Also
need to find way to put other kernel used ram to local node ram.
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Don Morris <don.morris@hp.com>
Bisected-by: Don Morris <don.morris@hp.com>
Tested-by: Don Morris <don.morris@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
|
|
nr_free_zone_pages(), nr_free_buffer_pages() and nr_free_pagecache_pages()
are horribly badly named, so accurately document them with code comments
in case of the misuse of them.
[akpm@linux-foundation.org: tweak comments]
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the amount of RAM that functions nr_free_*_pages return is
held in unsigned int. But in machines with big memory (exceeding 16TB),
the amount may be incorrect because of overflow, so fix it.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make a sweep through mm/ and convert code that uses -1 directly to using
the more appropriate NUMA_NO_NODE.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
page_outside_zone_boundaries()
Add a debug message which prints when a page is found outside of the
boundaries of the zone it should belong to. Format is:
"page $pfn outside zone [ $start_pfn - $end_pfn ]"
[akpm@linux-foundation.org: s/pr_debug/pr_err/]
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Freeing pages to uninitialized zones is not handled by
__free_one_page(), and should never happen when the code is correct.
Ran into this while writing some code that dynamically onlines extra
zones.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add 2 helpers (zone_end_pfn() and zone_spans_pfn()) to reduce code
duplication.
This also switches to using them in compaction (where an additional
variable needed to be renamed), page_alloc, vmstat, memory_hotplug, and
kmemleak.
Note that in compaction.c I avoid calling zone_end_pfn() repeatedly
because I expect at some point the sycronization issues with start_pfn &
spanned_pages will need fixing, either by actually using the seqlock or
clever memory barrier usage.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
No functional change, but the only purpose of the offlining argument to
migrate_pages() etc, was to ensure that __unmap_and_move() could migrate a
KSM page for memory hotremove (which took ksm_thread_mutex) but not for
other callers. Now all cases are safe, remove the arg.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The function names page_xchg_last_nid(), page_last_nid() and
reset_page_last_nid() were judged to be inconsistent so rename them to a
struct_field_op style pattern. As it looked jarring to have
reset_page_mapcount() and page_nid_reset_last() beside each other in
memmap_init_zone(), this patch also renames reset_page_mapcount() to
page_mapcount_reset(). There are others like init_page_count() but as
it is used throughout the arch code a rename would likely cause more
conflicts than it is worth.
[akpm@linux-foundation.org: fix zcache]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch introduces PF_MEMALLOC_NOIO on process flag('flags' field of
'struct task_struct'), so that the flag can be set by one task to avoid
doing I/O inside memory allocation in the task's context.
The patch trys to solve one deadlock problem caused by block device, and
the problem may happen at least in the below situations:
- during block device runtime resume, if memory allocation with
GFP_KERNEL is called inside runtime resume callback of any one of its
ancestors(or the block device itself), the deadlock may be triggered
inside the memory allocation since it might not complete until the block
device becomes active and the involed page I/O finishes. The situation
is pointed out first by Alan Stern. It is not a good approach to
convert all GFP_KERNEL[1] in the path into GFP_NOIO because several
subsystems may be involved(for example, PCI, USB and SCSI may be
involved for usb mass stoarage device, network devices involved too in
the iSCSI case)
- during block device runtime suspend, because runtime resume need to
wait for completion of concurrent runtime suspend.
- during error handling of usb mass storage deivce, USB bus reset will
be put on the device, so there shouldn't have any memory allocation with
GFP_KERNEL during USB bus reset, otherwise the deadlock similar with
above may be triggered. Unfortunately, any usb device may include one
mass storage interface in theory, so it requires all usb interface
drivers to handle the situation. In fact, most usb drivers don't know
how to handle bus reset on the device and don't provide .pre_set() and
.post_reset() callback at all, so USB core has to unbind and bind driver
for these devices. So it is still not practical to resort to GFP_NOIO
for solving the problem.
Also the introduced solution can be used by block subsystem or block
drivers too, for example, set the PF_MEMALLOC_NOIO flag before doing
actual I/O transfer.
It is not a good idea to convert all these GFP_KERNEL in the affected
path into GFP_NOIO because these functions doing that may be implemented
as library and will be called in many other contexts.
In fact, memalloc_noio_flags() can convert some of current static
GFP_NOIO allocation into GFP_KERNEL back in other non-affected contexts,
at least almost all GFP_NOIO in USB subsystem can be converted into
GFP_KERNEL after applying the approach and make allocation with GFP_NOIO
only happen in runtime resume/bus reset/block I/O transfer contexts
generally.
[1], several GFP_KERNEL allocation examples in runtime resume path
- pci subsystem
acpi_os_allocate
<-acpi_ut_allocate
<-ACPI_ALLOCATE_ZEROED
<-acpi_evaluate_object
<-__acpi_bus_set_power
<-acpi_bus_set_power
<-acpi_pci_set_power_state
<-platform_pci_set_power_state
<-pci_platform_power_transition
<-__pci_complete_power_transition
<-pci_set_power_state
<-pci_restore_standard_config
<-pci_pm_runtime_resume
- usb subsystem
usb_get_status
<-finish_port_resume
<-usb_port_resume
<-generic_resume
<-usb_resume_device
<-usb_resume_both
<-usb_runtime_resume
- some individual usb drivers
usblp, uvc, gspca, most of dvb-usb-v2 media drivers, cpia2, az6007, ....
That is just what I have found. Unfortunately, this allocation can only
be found by human being now, and there should be many not found since
any function in the resume path(call tree) may allocate memory with
GFP_KERNEL.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Several functions test MIGRATE_ISOLATE and some of those are hotpath but
MIGRATE_ISOLATE is used only if we enable CONFIG_MEMORY_ISOLATION(ie,
CMA, memory-hotplug and memory-failure) which are not common config
option. So let's not add unnecessary overhead and code when we don't
enable CONFIG_MEMORY_ISOLATION.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now all users of "number of pages managed by the buddy system" have been
converted to use zone->managed_pages, so set zone->present_pages to what
it should be:
present_pages = spanned_pages - absent_pages;
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Chris Clayton <chris2553@googlemail.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now we have zone->managed_pages for "pages managed by the buddy system
in the zone", so replace zone->present_pages with zone->managed_pages if
what the user really wants is number of allocatable pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Chris Clayton <chris2553@googlemail.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We now provide an option for users who don't want to specify physical
memory address in kernel commandline.
/*
* For movablemem_map=acpi:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* hotpluggable: n y y n
* movablemem_map: |_____| |_________|
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*/
So user just specify movablemem_map=acpi, and the kernel will use
hotpluggable info in SRAT to determine which memory ranges should be set
as ZONE_MOVABLE.
If all the memory ranges in SRAT is hotpluggable, then no memory can be
used by kernel. But before parsing SRAT, memblock has already reserve
some memory ranges for other purposes, such as for kernel image, and so
on. We cannot prevent kernel from using these memory. So we need to
exclude these ranges even if these memory is hotpluggable.
Furthermore, there could be several memory ranges in the single node
which the kernel resides in. We may skip one range that have memory
reserved by memblock, but if the rest of memory is too small, then the
kernel will fail to boot. So, make the whole node which the kernel
resides in un-hotpluggable. Then the kernel has enough memory to use.
NOTE: Using this way will cause NUMA performance down because the
whole node will be set as ZONE_MOVABLE, and kernel cannot use memory
on it. If users don't want to lose NUMA performance, just don't use
it.
[akpm@linux-foundation.org: fix warning]
[akpm@linux-foundation.org: use strcmp()]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When implementing movablemem_map boot option, we introduced an array
movablemem_map.map[] to store the memory ranges to be set as
ZONE_MOVABLE.
Since ZONE_MOVABLE is the latst zone of a node, if user didn't specify
the whole node memory range, we need to extend it to the node end so
that we can use it to prevent memblock from allocating memory in the
ranges user didn't specify.
We now implement movablemem_map boot option like this:
/*
* For movablemem_map=nn[KMG]@ss[KMG]:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* user specified: |__| |___|
* movablemem_map: |___| |_________| |______| ......
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*
* NOTE: In this case, SRAT info will be ingored.
*/
[akpm@linux-foundation.org: clean up code, fix build warning]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If kernelcore or movablecore is specified at the same time with
movablemem_map, movablemem_map will have higher priority to be
satisfied. This patch will make find_zone_movable_pfns_for_nodes()
calculate zone_movable_pfn[] with the limit from zone_movable_limit[].
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Tested-by: Lin Feng <linfeng@cn.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce a new array zone_movable_limit[] to store the ZONE_MOVABLE
limit from movablemem_map boot option for all nodes. The function
sanitize_zone_movable_limit() will find out to which node the ranges in
movable_map.map[] belongs, and calculates the low boundary of
ZONE_MOVABLE for each node.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Liu Jiang <jiang.liu@huawei.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Tested-by: Lin Feng <linfeng@cn.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add functions to parse movablemem_map boot option. Since the option
could be specified more then once, all the maps will be stored in the
global variable movablemem_map.map array.
And also, we keep the array in monotonic increasing order by start_pfn.
And merge all overlapped ranges.
[akpm@linux-foundation.org: improve comment]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: remove unneeded parens]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Tested-by: Lin Feng <linfeng@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
`int' is an inappropriate type for a number-of-pages counter.
While we're there, use the clamp() macro.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Satoru Moriya <satoru.moriya@hds.com>
Cc: Simon Jeons <simon.jeons@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As per documentation and other places calling putback_lru_pages(),
putback_lru_pages() is called on error only. Make the CMA code behave
consistently.
[akpm@linux-foundation.org: remove a test-n-branch in the wrapup code]
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
|
|
Commit c060f943d092 ("mm: use aligned zone start for pfn_to_bitidx
calculation") fixed out calculation of the index into the pageblock
bitmap when a !SPARSEMEM zome was not aligned to pageblock_nr_pages.
However, the _allocation_ of that bitmap had never taken this alignment
requirement into accout, so depending on the exact size and alignment of
the zone, the use of that index could then access past the allocation,
resulting in some very subtle memory corruption.
This was reported (and bisected) by Ingo Molnar: one of his random
config builds would hang with certain very specific kernel command line
options.
In the meantime, commit c060f943d092 has been marked for stable, so this
fix needs to be back-ported to the stable kernels that backported the
commit to use the right alignment.
Bisected-and-tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The total number of low memory pages is determined as totalram_pages -
totalhigh_pages, so without this patch all CMA pageblocks placed in
highmem were accounted to low memory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move rt scheduler definitions out of include/linux/sched.h into
new file include/linux/sched/rt.h
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Eric Wong reported on 3.7 and 3.8-rc2 that ppoll() got stuck when
waiting for POLLIN on a local TCP socket. It was easier to trigger if
there was disk IO and dirty pages at the same time and he bisected it to
commit 1fb3f8ca0e92 ("mm: compaction: capture a suitable high-order page
immediately when it is made available").
The intention of that patch was to improve high-order allocations under
memory pressure after changes made to reclaim in 3.6 drastically hurt
THP allocations but the approach was flawed. For Eric, the problem was
that page->pfmemalloc was not being cleared for captured pages leading
to a poor interaction with swap-over-NFS support causing the packets to
be dropped. However, I identified a few more problems with the patch
including the fact that it can increase contention on zone->lock in some
cases which could result in async direct compaction being aborted early.
In retrospect the capture patch took the wrong approach. What it should
have done is mark the pageblock being migrated as MIGRATE_ISOLATE if it
was allocating for THP and avoided races that way. While the patch was
showing to improve allocation success rates at the time, the benefit is
marginal given the relative complexity and it should be revisited from
scratch in the context of the other reclaim-related changes that have
taken place since the patch was first written and tested. This patch
partially reverts commit 1fb3f8ca0e92 ("mm: compaction: capture a
suitable high-order page immediately when it is made available").
Reported-and-tested-by: Eric Wong <normalperson@yhbt.net>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current calculation in pfn_to_bitidx assumes that (pfn -
zone->zone_start_pfn) >> pageblock_order will return the same bit for
all pfn in a pageblock. If zone_start_pfn is not aligned to
pageblock_nr_pages, this may not always be correct.
Consider the following with pageblock order = 10, zone start 2MB:
pfn | pfn - zone start | (pfn - zone start) >> page block order
----------------------------------------------------------------
0x26000 | 0x25e00 | 0x97
0x26100 | 0x25f00 | 0x97
0x26200 | 0x26000 | 0x98
0x26300 | 0x26100 | 0x98
This means that calling {get,set}_pageblock_migratetype on a single page
will not set the migratetype for the full block. Fix this by rounding
down zone_start_pfn when doing the bitidx calculation.
For our use case, the effects of this bug were mostly tied to the fact
that CMA allocations would either take a long time or fail to happen.
Depending on the driver using CMA, this could result in anything from
visual glitches to application failures.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 702d1a6e0766 ("memory-hotplug: fix kswapd looping forever
problem") added an isolated pageblocks counter (nr_pageblock_isolate in
struct zone) and used it to adjust free pages counter in
zone_watermark_ok_safe() to prevent kswapd looping forever problem.
Then later, commit 2139cbe627b8 ("cma: fix counting of isolated pages")
fixed accounting of isolated pages in global free pages counter. It
made the previous zone_watermark_ok_safe() fix unnecessary and
potentially harmful (cause now isolated pages may be accounted twice
making free pages counter incorrect).
This patch removes the special isolated pageblocks counter altogether
which fixes zone_watermark_ok_safe() free pages check.
Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Aaditya Kumar <aaditya.kumar.30@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Memory returned to free_contig_range() must have no other references.
Let kernel to complain loudly if page reference count is not equal to 1.
[rientjes@google.com: support sparsemem]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When a process tries to allocate a page with the __GFP_KMEMCG flag, the
page allocator will call the corresponding memcg functions to validate
the allocation. Tasks in the root memcg can always proceed.
To avoid adding markers to the page - and a kmem flag that would
necessarily follow, as much as doing page_cgroup lookups for no reason,
whoever is marking its allocations with __GFP_KMEMCG flag is responsible
for telling the page allocator that this is such an allocation at
free_pages() time. This is done by the invocation of
__free_accounted_pages() and free_accounted_pages().
Signed-off-by: Glauber Costa <glommer@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: JoonSoo Kim <js1304@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While allocating pages using buddy allocator, the compound page is
probably split up to free pages. Under these circumstances, the compound
page should be destroyed by destroy_compound_page(). However, there is a
duplicate check to judge if the page is compound.
Remove the duplicate check since the compound_order() returns 0 when the
page doesn't have PG_head set in destroy_compound_page(). That is to say,
destroy_compound_page() needn't check PageHead().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma
Pull Automatic NUMA Balancing bare-bones from Mel Gorman:
"There are three implementations for NUMA balancing, this tree
(balancenuma), numacore which has been developed in tip/master and
autonuma which is in aa.git.
In almost all respects balancenuma is the dumbest of the three because
its main impact is on the VM side with no attempt to be smart about
scheduling. In the interest of getting the ball rolling, it would be
desirable to see this much merged for 3.8 with the view to building
scheduler smarts on top and adapting the VM where required for 3.9.
The most recent set of comparisons available from different people are
mel: https://lkml.org/lkml/2012/12/9/108
mingo: https://lkml.org/lkml/2012/12/7/331
tglx: https://lkml.org/lkml/2012/12/10/437
srikar: https://lkml.org/lkml/2012/12/10/397
The results are a mixed bag. In my own tests, balancenuma does
reasonably well. It's dumb as rocks and does not regress against
mainline. On the other hand, Ingo's tests shows that balancenuma is
incapable of converging for this workloads driven by perf which is bad
but is potentially explained by the lack of scheduler smarts. Thomas'
results show balancenuma improves on mainline but falls far short of
numacore or autonuma. Srikar's results indicate we all suffer on a
large machine with imbalanced node sizes.
My own testing showed that recent numacore results have improved
dramatically, particularly in the last week but not universally.
We've butted heads heavily on system CPU usage and high levels of
migration even when it shows that overall performance is better.
There are also cases where it regresses. Of interest is that for
specjbb in some configurations it will regress for lower numbers of
warehouses and show gains for higher numbers which is not reported by
the tool by default and sometimes missed in treports. Recently I
reported for numacore that the JVM was crashing with
NullPointerExceptions but currently it's unclear what the source of
this problem is. Initially I thought it was in how numacore batch
handles PTEs but I'm no longer think this is the case. It's possible
numacore is just able to trigger it due to higher rates of migration.
These reports were quite late in the cycle so I/we would like to start
with this tree as it contains much of the code we can agree on and has
not changed significantly over the last 2-3 weeks."
* tag 'balancenuma-v11' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma: (50 commits)
mm/rmap, migration: Make rmap_walk_anon() and try_to_unmap_anon() more scalable
mm/rmap: Convert the struct anon_vma::mutex to an rwsem
mm: migrate: Account a transhuge page properly when rate limiting
mm: numa: Account for failed allocations and isolations as migration failures
mm: numa: Add THP migration for the NUMA working set scanning fault case build fix
mm: numa: Add THP migration for the NUMA working set scanning fault case.
mm: sched: numa: Delay PTE scanning until a task is scheduled on a new node
mm: sched: numa: Control enabling and disabling of NUMA balancing if !SCHED_DEBUG
mm: sched: numa: Control enabling and disabling of NUMA balancing
mm: sched: Adapt the scanning rate if a NUMA hinting fault does not migrate
mm: numa: Use a two-stage filter to restrict pages being migrated for unlikely task<->node relationships
mm: numa: migrate: Set last_nid on newly allocated page
mm: numa: split_huge_page: Transfer last_nid on tail page
mm: numa: Introduce last_nid to the page frame
sched: numa: Slowly increase the scanning period as NUMA faults are handled
mm: numa: Rate limit setting of pte_numa if node is saturated
mm: numa: Rate limit the amount of memory that is migrated between nodes
mm: numa: Structures for Migrate On Fault per NUMA migration rate limiting
mm: numa: Migrate pages handled during a pmd_numa hinting fault
mm: numa: Migrate on reference policy
...
|
|
Merge misc VM changes from Andrew Morton:
"The rest of most-of-MM. The other MM bits await a slab merge.
This patch includes the addition of a huge zero_page. Not a
performance boost but it an save large amounts of physical memory in
some situations.
Also a bunch of Fujitsu engineers are working on memory hotplug.
Which, as it turns out, was badly broken. About half of their patches
are included here; the remainder are 3.8 material."
However, this merge disables CONFIG_MOVABLE_NODE, which was totally
broken. We don't add new features with "default y", nor do we add
Kconfig questions that are incomprehensible to most people without any
help text. Does the feature even make sense without compaction or
memory hotplug?
* akpm: (54 commits)
mm/bootmem.c: remove unused wrapper function reserve_bootmem_generic()
mm/memory.c: remove unused code from do_wp_page()
asm-generic, mm: pgtable: consolidate zero page helpers
mm/hugetlb.c: fix warning on freeing hwpoisoned hugepage
hwpoison, hugetlbfs: fix RSS-counter warning
hwpoison, hugetlbfs: fix "bad pmd" warning in unmapping hwpoisoned hugepage
mm: protect against concurrent vma expansion
memcg: do not check for mm in __mem_cgroup_count_vm_event
tmpfs: support SEEK_DATA and SEEK_HOLE (reprise)
mm: provide more accurate estimation of pages occupied by memmap
fs/buffer.c: remove redundant initialization in alloc_page_buffers()
fs/buffer.c: do not inline exported function
writeback: fix a typo in comment
mm: introduce new field "managed_pages" to struct zone
mm, oom: remove statically defined arch functions of same name
mm, oom: remove redundant sleep in pagefault oom handler
mm, oom: cleanup pagefault oom handler
memory_hotplug: allow online/offline memory to result movable node
numa: add CONFIG_MOVABLE_NODE for movable-dedicated node
mm, memcg: avoid unnecessary function call when memcg is disabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
|
|
If SPARSEMEM is enabled, it won't build page structures for non-existing
pages (holes) within a zone, so provide a more accurate estimation of
pages occupied by memmap if there are bigger holes within the zone.
And pages for highmem zones' memmap will be allocated from lowmem, so
charge nr_kernel_pages for that.
[akpm@linux-foundation.org: mark calc_memmap_size __paging_init]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Chris Clayton <chris2553@googlemail.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Tested-by: Jianguo Wu <wujianguo@huawei.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently a zone's present_pages is calcuated as below, which is
inaccurate and may cause trouble to memory hotplug.
spanned_pages - absent_pages - memmap_pages - dma_reserve.
During fixing bugs caused by inaccurate zone->present_pages, we found
zone->present_pages has been abused. The field zone->present_pages may
have different meanings in different contexts:
1) pages existing in a zone.
2) pages managed by the buddy system.
For more discussions about the issue, please refer to:
http://lkml.org/lkml/2012/11/5/866
https://patchwork.kernel.org/patch/1346751/
This patchset tries to introduce a new field named "managed_pages" to
struct zone, which counts "pages managed by the buddy system". And revert
zone->present_pages to count "physical pages existing in a zone", which
also keep in consistence with pgdat->node_present_pages.
We will set an initial value for zone->managed_pages in function
free_area_init_core() and will adjust it later if the initial value is
inaccurate.
For DMA/normal zones, the initial value is set to:
(spanned_pages - absent_pages - memmap_pages - dma_reserve)
Later zone->managed_pages will be adjusted to the accurate value when the
bootmem allocator frees all free pages to the buddy system in function
free_all_bootmem_node() and free_all_bootmem().
The bootmem allocator doesn't touch highmem pages, so highmem zones'
managed_pages is set to the accurate value "spanned_pages - absent_pages"
in function free_area_init_core() and won't be updated anymore.
This patch also adds a new field "managed_pages" to /proc/zoneinfo
and sysrq showmem.
[akpm@linux-foundation.org: small comment tweaks]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need a node which only contains movable memory. This feature is very
important for node hotplug. If a node has normal/highmem, the memory may
be used by the kernel and can't be offlined. If the node only contains
movable memory, we can offline the memory and the node.
All are prepared, we can actually introduce N_MEMORY.
add CONFIG_MOVABLE_NODE make we can use it for movable-dedicated node
[akpm@linux-foundation.org: fix Kconfig text]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
initialization
N_HIGH_MEMORY stands for the nodes that has normal or high memory.
N_MEMORY stands for the nodes that has any memory.
The code here need to handle with the nodes which have memory, we should
use N_MEMORY instead.
Since we introduced N_MEMORY, we update the initialization of node_states.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Lin Feng <linfeng@cn.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__alloc_contig_migrate_range() should use all possible ways to get all the
pages migrated from the given memory range, so pruning per-cpu lru lists
for all CPUs is required, regadless the cost of such operation. Otherwise
some pages which got stuck at per-cpu lru list might get missed by
migration procedure causing the contiguous allocation to fail.
Reported-by: SeongHwan Yoon <sunghwan.yun@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commits 2139cbe627b8 ("cma: fix counting of isolated pages") and
d95ea5d18e69 ("cma: fix watermark checking") introduced a reliable
method of free page accounting when memory is being allocated from CMA
regions, so the workaround introduced earlier by commit 49f223a9cd96
("mm: trigger page reclaim in alloc_contig_range() to stabilise
watermarks") can be finally removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 2139cbe627b8 ("cma: fix counting of isolated pages") free
pages in isolated pageblocks are not accounted to NR_FREE_PAGES counters,
so watermarks check is not required if one operates on a free page in
isolated pageblock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
