| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (47 commits)
Driver core: Don't call put methods while holding a spinlock
Driver core: Remove unneeded routines from driver core
Driver core: Fix potential deadlock in driver core
PCI: enable driver multi-threaded probe
Driver Core: add ability for drivers to do a threaded probe
sysfs: add proper sysfs_init() prototype
drivers/base: check errors
drivers/base: Platform notify needs to occur before drivers attach to the device
v4l-dev2: handle __must_check
add CONFIG_ENABLE_MUST_CHECK
add __must_check to device management code
Driver core: fixed add_bind_files() definition
Driver core: fix comments in drivers/base/power/resume.c
sysfs_remove_bin_file: no return value, dump_stack on error
kobject: must_check fixes
Driver core: add ability for devices to create and remove bin files
Class: add support for class interfaces for devices
Driver core: create devices/virtual/ tree
Driver core: add device_rename function
Driver core: add ability for classes to handle devices properly
...
|
|
Add the pm_trace attribute in /sys/power which has to be explicitly set to
one to really enable the "PM tracing" code compiled in when CONFIG_PM_TRACE
is set (which modifies the machine's CMOS clock in unpredictable ways).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Change suspend_console() so that it waits for all consoles to flush the
remaining messages and make it possible to switch the console suspending off
with the help of a Kconfig option.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Stefan Seyfried <seife@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make swsusp use memory bitmaps to store its internal information during the
resume phase of the suspend-resume cycle.
If the pfns of saveable pages are saved during the suspend phase instead of
the kernel virtual addresses of these pages, we can use them during the resume
phase directly to set the corresponding bits in a memory bitmap. Then, this
bitmap is used to mark the page frames corresponding to the pages that were
saveable before the suspend (aka "unsafe" page frames).
Next, we allocate as many page frames as needed to store the entire suspend
image and make sure that there will be some extra free "safe" page frames for
the list of PBEs constructed later. Subsequently, the image is loaded and, if
possible, the data loaded from it are written into their "original" page
frames (ie. the ones they had occupied before the suspend).
The image data that cannot be written into their "original" page frames are
loaded into "safe" page frames and their "original" kernel virtual addresses,
as well as the addresses of the "safe" pages containing their copies, are
stored in a list of PBEs. Finally, the list of PBEs is used to copy the
remaining image data into their "original" page frames (this is done
atomically, by the architecture-dependent parts of swsusp).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Introduce the memory bitmap data structure and make swsusp use in the suspend
phase.
The current swsusp's internal data structure is not very efficient from the
memory usage point of view, so it seems reasonable to replace it with a data
structure that will require less memory, such as a pair of bitmaps.
The idea is to use bitmaps that may be allocated as sets of individual pages,
so that we can avoid making allocations of order greater than 0. For this
reason the memory bitmap structure consists of several linked lists of objects
that contain pointers to memory pages with the actual bitmap data. Still, for
a typical system all of these lists fit in a single page, so it's reasonable
to introduce an additional mechanism allowing us to allocate all of them
efficiently without sacrificing the generality of the design. This is done
with the help of the chain_allocator structure and associated functions.
We need to use two memory bitmaps during the suspend phase of the
suspend-resume cycle. One of them is necessary for marking the saveable
pages, and the second is used to mark the pages in which to store the copies
of them (aka image pages).
First, the bitmaps are created and we allocate as many image pages as needed
(the corresponding bits in the second bitmap are set as soon as the pages are
allocated). Second, the bits corresponding to the saveable pages are set in
the first bitmap and the saveable pages are copied to the image pages.
Finally, the first bitmap is used to save the kernel virtual addresses of the
saveable pages and the second one is used to save the contents of the image
pages.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Introduce some constants that hopefully will help improve the readability of
code in kernel/power/snapshot.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The name of the pagedir_nosave variable does not make sense any more, so it
seems reasonable to change it to something more meaningful.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Get rid of the FIXME in kernel/power/snapshot.c#alloc_pagedir() and
simplify the functions called by it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Move some functions in kernel/power/snapshot.c to a better place (in the
same file) and introduce free_image_page() (will be necessary in the
future).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Clean up mm/page_alloc.c#mark_free_pages() and make it avoid clearing
PageNosaveFree for PageNosave pages. This allows us to get rid of an ugly
hack in kernel/power/snapshot.c#copy_data_pages().
Additionally, the page-copying loop in copy_data_pages() is moved to an
inline function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The current suspend code has to be run on one CPU, so we use the CPU
hotplug to take the non-boot CPUs offline on SMP machines. However, we
should also make sure that these CPUs will not be enabled by someone else
after we have disabled them.
The functions disable_nonboot_cpus() and enable_nonboot_cpus() are moved to
kernel/cpu.c, because they now refer to some stuff in there that should
better be static. Also it's better if disable_nonboot_cpus() returns an
error instead of panicking if something goes wrong, and
enable_nonboot_cpus() has no reason to panic(), because the CPUs may have
been enabled by the userland before it tries to take them online.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add comments describing struct snapshot_handle and its members, change the
confusing name of its member 'page' to 'cur'.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Clean up some loops over pfns for each zone in snapshot.c: reduce the
number of additions to perform, rework detection of saveable pages and make
the code a bit less difficult to understand, hopefully.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Implement async reads for swsusp resuming.
Crufty old PIII testbox:
15.7 MB/s -> 20.3 MB/s
Sony Vaio:
14.6 MB/s -> 33.3 MB/s
I didn't implement the post-resume bio_set_pages_dirty(). I don't really
understand why resume needs to run set_page_dirty() against these pages.
It might be a worry that this code modifies PG_Uptodate, PG_Error and
PG_Locked against the image pages. Can this possibly affect the resumed-into
kernel? Hopefully not, if we're atomically restoring its mem_map?
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jens Axboe <axboe@suse.de>
Cc: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add some instrumentation to the swsusp readin code to show what bandwidth
we're achieving.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Switch the swsusp writeout code from 4k-at-a-time to 4MB-at-a-time.
Crufty old PIII testbox:
12.9 MB/s -> 20.9 MB/s
Sony Vaio:
14.7 MB/s -> 26.5 MB/s
The implementation is crude. A better one would use larger BIOs, but wouldn't
gain any performance.
The memcpys will be mostly pipelined with the IO and basically come for free.
The ENOMEM path has not been tested. It should be.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add some instrumentation to the swsusp writeout code to show what bandwidth
we're achieving.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove the new suspend_prepare() phase. It doesn't seem very usable,
has never been tested, doesn't address fault cleanup, and would need
a sibling resume_complete(); plus there are no real use cases. It
could be restored later if those issues get resolved.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add a new PM_SYSFS_DEPRECATED config option to control whether or
not the /sys/devices/.../power/state files are provided. This will
make it easier to get rid of that mechanism when the time comes,
and to verify that userspace tools work right without it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is the first of this series that should actually change any
behavior ... by issuing the new event, now tha the rest of the kernel is
prepared to receive it.
This converts the PM core to issue the new PRETHAW message, which the rest of
the kernel is now ready to receive.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Allow devices to participate in the suspend process more intimately,
in particular, allow the final phase (with interrupts disabled) to
also be open to normal devices, not just system devices.
Also, allow classes to participate in device suspend.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
PAE + swsusp results in hard-to-debug crash about 50% of time during
resume. Cause is known, fix needs to be ported from x86-64 (but we can't
make it to 2.6.18, and I'd like this to be worked around in 2.6.18).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It should be possible to suspend, either to RAM or to disk, if there's a
traced process that has just reached a breakpoint. However, this is a
special case, because its parent process might have been frozen already and
then we are unable to deliver the "freeze" signal to the traced process.
If this happens, it's better to cancel the freezing of the traced process.
Ref. http://bugzilla.kernel.org/show_bug.cgi?id=6787
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove the deprecated and no longer used pm_unregister_all().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Do not panic a machine when swsusp signature can't be read.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
kernel/power/swap.c: In function 'swsusp_write':
kernel/power/swap.c:275: warning: 'start' may be used uninitialized in this function
gcc isn't smart enough, so help it.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
swsusp should not use memcpy for snapshotting memory, because on some
architectures memcpy may increase preempt_count (i386 does this when
CONFIG_X86_USE_3DNOW is set). Then, as a result, wrong value of preempt_count
is stored in the image.
Replace memcpy in copy_data_pages with an open-coded loop.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove SWSUSP_ENCRYPT config option; it is no longer implemented.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
CONFIG_PM_TRACES scrogs your RTC. Mark it as experimental, and defaulting to
`off'.
Also beef up the help message a bit.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This reverts commits
3e3318dee0878d42ed62a19c292a2ac284135db3 [PATCH] swsusp: x86_64 mark special saveable/unsaveable pages
b6370d96e09944c6e3ae8d5743ca8a8ab1f79f6c [PATCH] swsusp: i386 mark special saveable/unsaveable pages
ce4ab0012b32c1a4a1d6e934aeb73bf3151c48d9 [PATCH] swsusp: add architecture special saveable pages support
because not only do they apparently cause page faults on x86, the
infrastructure doesn't compile on powerpc.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Not that x86-64 and other architecture support should be difficult to
add (trivial fixups to the data format and add the proper linker script
entry).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Considering that there isn't a lot of hw we can depend on during resume,
this is about as good as it gets.
This is x86-only for now, although the basic concept (and most of the
code) will certainly work on almost any platform.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make swsusp allocate only as much memory as needed to store the image data
and metadata during resume.
Without this patch swsusp additionally allocates many page frames that will
conflict with the "original" locations of the image data and are considered
as "unsafe", treating them as "eaten" pages (ie. allocated but unusable).
The patch makes swsusp allocate as many pages as it'll need to store the
data read from the image in one shot, creating a list of allocated "safe"
pages, and use the observation that all pages allocated by it are marked
with the PG_nosave and PG_nosave_free flags set. Namely, when it's about
to load an image page, swsusp can check whether the page frame
corresponding to the "original" location of this page has been allocated
(ie. if the page frame has the PG_nosave and PG_nosave_free flags set) and
if so, it can load the page directly into this page frame. Otherwise it
uses an allocated "safe" page from the list to store the data that will be
copied to their "original" location later on.
This allows us to save many page copyings and page allocations during
resume and in the future it may allow us to load images greater than 50% of
the normal zone.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: "Pavel Machek" <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- make needlessly global functions static
- make dummy functions static inline
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
swsusp allocates memory from the normal zone, so it cannot use lowmem
reserve pages from the lower zones. Therefore it should not count these
pages as available to it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
1. Add architecture specific pages save/restore support. Next two patches
will use this to save/restore 'ACPI NVS' pages.
2. Allow reserved pages 'nosave'. This could avoid save/restore BIOS
reserved pages.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Rework the swsusp's memory shrinker in the following way:
- Simplify balance_pgdat() by removing all of the swsusp-related code
from it.
- Make shrink_all_memory() use shrink_slab() and a new function
shrink_all_zones() which calls shrink_active_list() and
shrink_inactive_list() directly for each zone in a way that's optimized
for suspend.
In shrink_all_memory() we try to free exactly as many pages as the caller
asks for, preferably in one shot, starting from easier targets. If slab
caches are huge, they are most likely to have enough pages to reclaim.
The inactive lists are next (the zones with more inactive pages go first)
etc.
Each time shrink_all_memory() attempts to shrink the active and inactive
lists for each zone in 5 passes. In the first pass, only the inactive
lists are taken into consideration. In the next two passes the active
lists are also shrunk, but mapped pages are not reclaimed. In the last
two passes the active and inactive lists are shrunk and mapped pages are
reclaimed as well. The aim of this is to alter the reclaim logic to choose
the best pages to keep on resume and improve the responsiveness of the
resumed system.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
kernel/power/main.c: In function 'suspend_prepare':
kernel/power/main.c:89: warning: implicit declaration of function 'suspend_console'
kernel/power/main.c: In function 'suspend_finish':
kernel/power/main.c:137: warning: implicit declaration of function 'resume_console'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Trying to suspend/resume with console messages flying all around is
doomed to failure, when the devices that the messages are trying to
go to are being shut down.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There's an off-by-1 in kernel/power/main.c:state_store() ... if your
kernel just happens to have some non-zero data at pm_states[PM_SUSPEND_MAX]
(i.e. one past the end of the array) then it'll let you write anything you
want to /sys/power/state and in response the box will enter S5.
Signed-off-by: dean gaudet <dean@arctic.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The function free_pagedir() used by swsusp for freeing its internal data
structures clears the PG_nosave and PG_nosave_free flags for each page
being freed.
However, during resume PG_nosave_free set means that the page in
question is "unsafe" (ie. it will be overwritten in the process of
restoring the saved system state from the image), so it should not be
used for the image data.
Therefore free_pagedir() should not clear PG_nosave_free if it's called
during resume (otherwise "unsafe" pages freed by it may be used for
storing the image data and the data may get corrupted later on).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Since the last user is removed in -mm, we can now remove this long deprecated
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The note that SOFTWARE_SUSPEND doesn't need APM is helpful, but nowadays
the information that it doesn't need ACPI, too, is even more helpful.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
strace /bin/bash misbehaves after resume; this fixes it.
(akpm: it's scary calling refrigerator() in state TASK_TRACED, but it seems to
do the right thing).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If there's an error in load_image() we should return that without checking
snapshot_image_loaded.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- Moved check for online cpu out of smp_prepare_cpu()
- Moved default declaration of smp_prepare_cpu() to kernel/cpu.c
- Removed lock_cpu_hotplug() from smp_prepare_cpu() to around it, since
its called from cpu_up() as well now.
- Removed clearing from cpu_present_map during cpu_offline as it breaks
using cpu_up() directly during a subsequent online operation.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add the SNAPSHOT_S2RAM ioctl to the snapshot device.
This ioctl allows a userland application to make the system (previously frozen
with the SNAPSHOT_FREE ioctl) enter the S3 state without freezing processes
and disabling nonboot CPUs for the second time.
This will allow us to implement the suspend-to-disk-and-RAM (STDR)
functionality in the userland suspend tools.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove the console-switching code from the suspend part of the swsusp userland
interface and let the userland tools switch the console.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
