| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to centralize the isolation features, to be done by the housekeeping
subsystem and scheduler domain isolation is a significant part of it.
No intended behaviour change, we just reuse the housekeeping cpumask
and core code.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Link: http://lkml.kernel.org/r/1509072159-31808-11-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The cgroup_taskset structure within the larger cgroup_mgctx structure
is supposed to be used once and then discarded. That is not really the
case in the hotplug code path:
cpuset_hotplug_workfn()
- cgroup_transfer_tasks()
- cgroup_migrate()
- cgroup_migrate_add_task()
- cgroup_migrate_execute()
In this case, the cgroup_migrate() function is called multiple time
with the same cgroup_mgctx structure to transfer the tasks from
one cgroup to another one-by-one. The second time cgroup_migrate()
is called, the cgroup_taskset will be in an incorrect state and so
may cause the system to panic. For example,
[ 150.888410] Faulting instruction address: 0xc0000000001db648
[ 150.888414] Oops: Kernel access of bad area, sig: 11 [#1]
[ 150.888417] SMP NR_CPUS=2048
[ 150.888417] NUMA
[ 150.888419] pSeries
:
[ 150.888545] NIP [c0000000001db648] cpuset_can_attach+0x58/0x1b0
[ 150.888548] LR [c0000000001db638] cpuset_can_attach+0x48/0x1b0
[ 150.888551] Call Trace:
[ 150.888554] [c0000005f65cb940] [c0000000001db638] cpuset_can_attach+0x48/0x1b 0 (unreliable)
[ 150.888559] [c0000005f65cb9a0] [c0000000001cff04] cgroup_migrate_execute+0xc4/0x4b0
[ 150.888563] [c0000005f65cba20] [c0000000001d7d14] cgroup_transfer_tasks+0x1d4/0x370
[ 150.888568] [c0000005f65cbb70] [c0000000001ddcb0] cpuset_hotplug_workfn+0x710/0x8f0
[ 150.888572] [c0000005f65cbc80] [c00000000012032c] process_one_work+0x1ac/0x4d0
[ 150.888576] [c0000005f65cbd20] [c0000000001206f8] worker_thread+0xa8/0x5b0
[ 150.888580] [c0000005f65cbdc0] [c0000000001293f8] kthread+0x168/0x1b0
[ 150.888584] [c0000005f65cbe30] [c00000000000b368] ret_from_kernel_thread+0x5c/0x74
To allow reuse of the cgroup_mgctx structure, some fields in that
structure are now re-initialized at the end of cgroup_migrate_execute()
function call so that the structure can be reused again in a later
iteration without causing problem.
This bug was introduced in the commit e595cd706982 ("group: track
migration context in cgroup_mgctx") in 4.11. This commit moves the
cgroup_taskset initialization out of cgroup_migrate(). The commit
10467270fb3 ("cgroup: don't call migration methods if there are no
tasks to migrate") helped, but did not completely resolve the problem.
Fixes: e595cd706982bff0211e6fafe5a108421e747fbc ("group: track migration context in cgroup_mgctx")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v4.11+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Three fixes:
- fix a suspend/resume cpusets bug
- fix a !CONFIG_NUMA_BALANCING bug
- fix a kerneldoc warning"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix nuisance kernel-doc warning
sched/cpuset/pm: Fix cpuset vs. suspend-resume bugs
sched/fair: Fix wake_affine_llc() balancing rules
|
|
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
|
|
Cpusets vs. suspend-resume is _completely_ broken. And it got noticed
because it now resulted in non-cpuset usage breaking too.
On suspend cpuset_cpu_inactive() doesn't call into
cpuset_update_active_cpus() because it doesn't want to move tasks about,
there is no need, all tasks are frozen and won't run again until after
we've resumed everything.
But this means that when we finally do call into
cpuset_update_active_cpus() after resuming the last frozen cpu in
cpuset_cpu_active(), the top_cpuset will not have any difference with
the cpu_active_mask and this it will not in fact do _anything_.
So the cpuset configuration will not be restored. This was largely
hidden because we would unconditionally create identity domains and
mobile users would not in fact use cpusets much. And servers what do use
cpusets tend to not suspend-resume much.
An addition problem is that we'd not in fact wait for the cpuset work to
finish before resuming the tasks, allowing spurious migrations outside
of the specified domains.
Fix the rebuild by introducing cpuset_force_rebuild() and fix the
ordering with cpuset_wait_for_hotplug().
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: deb7aa308ea2 ("cpuset: reorganize CPU / memory hotplug handling")
Link: http://lkml.kernel.org/r/20170907091338.orwxrqkbfkki3c24@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"Several notable changes this cycle:
- Thread mode was merged. This will be used for cgroup2 support for
CPU and possibly other controllers. Unfortunately, CPU controller
cgroup2 support didn't make this pull request but most contentions
have been resolved and the support is likely to be merged before
the next merge window.
- cgroup.stat now shows the number of descendant cgroups.
- cpuset now can enable the easier-to-configure v2 behavior on v1
hierarchy"
* 'for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
cpuset: Allow v2 behavior in v1 cgroup
cgroup: Add mount flag to enable cpuset to use v2 behavior in v1 cgroup
cgroup: remove unneeded checks
cgroup: misc changes
cgroup: short-circuit cset_cgroup_from_root() on the default hierarchy
cgroup: re-use the parent pointer in cgroup_destroy_locked()
cgroup: add cgroup.stat interface with basic hierarchy stats
cgroup: implement hierarchy limits
cgroup: keep track of number of descent cgroups
cgroup: add comment to cgroup_enable_threaded()
cgroup: remove unnecessary empty check when enabling threaded mode
cgroup: update debug controller to print out thread mode information
cgroup: implement cgroup v2 thread support
cgroup: implement CSS_TASK_ITER_THREADED
cgroup: introduce cgroup->dom_cgrp and threaded css_set handling
cgroup: add @flags to css_task_iter_start() and implement CSS_TASK_ITER_PROCS
cgroup: reorganize cgroup.procs / task write path
cgroup: replace css_set walking populated test with testing cgrp->nr_populated_csets
cgroup: distinguish local and children populated states
cgroup: remove now unused list_head @pending in cgroup_apply_cftypes()
...
|
|
TIF_MEMDIE is set only to the tasks whick were either directly selected
by the OOM killer or passed through mark_oom_victim from the allocator
path. tsk_is_oom_victim is more generic and allows to identify all
tasks (threads) which share the mm with the oom victim.
Please note that the freezer still needs to check TIF_MEMDIE because we
cannot thaw tasks which do not participage in oom_victims counting
otherwise a !TIF_MEMDIE task could interfere after oom_disbale returns.
Link: http://lkml.kernel.org/r/20170810075019.28998-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit fa06235b8eb0 ("cgroup: reset css on destruction") caused
css_reset callback to be called from the offlining path. Although it
solves the problem mentioned in the commit description ("For instance,
memory cgroup needs to reset memory.low, otherwise pages charged to a
dead cgroup might never get reclaimed."), generally speaking, it's not
correct.
An offline cgroup can still be a resource domain, and we shouldn't grant
it more resources than it had before deletion.
For instance, if an offline memory cgroup has dirty pages, we should
still imply i/o limits during writeback.
The css_reset callback is designed to return the cgroup state into the
original state, that means reset all limits and counters. It's
spomething different from the offlining, and we shouldn't use it from
the offlining path. Instead, we should adjust necessary settings from
the per-controller css_offline callbacks (e.g. reset memory.low).
Link: http://lkml.kernel.org/r/20170727130428.28856-2-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- Add 'cross-release' support to lockdep, which allows APIs like
completions, where it's not the 'owner' who releases the lock, to be
tracked. It's all activated automatically under
CONFIG_PROVE_LOCKING=y.
- Clean up (restructure) the x86 atomics op implementation to be more
readable, in preparation of KASAN annotations. (Dmitry Vyukov)
- Fix static keys (Paolo Bonzini)
- Add killable versions of down_read() et al (Kirill Tkhai)
- Rework and fix jump_label locking (Marc Zyngier, Paolo Bonzini)
- Rework (and fix) tlb_flush_pending() barriers (Peter Zijlstra)
- Remove smp_mb__before_spinlock() and convert its usages, introduce
smp_mb__after_spinlock() (Peter Zijlstra)
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
locking/lockdep/selftests: Fix mixed read-write ABBA tests
sched/completion: Avoid unnecessary stack allocation for COMPLETION_INITIALIZER_ONSTACK()
acpi/nfit: Fix COMPLETION_INITIALIZER_ONSTACK() abuse
locking/pvqspinlock: Relax cmpxchg's to improve performance on some architectures
smp: Avoid using two cache lines for struct call_single_data
locking/lockdep: Untangle xhlock history save/restore from task independence
locking/refcounts, x86/asm: Disable CONFIG_ARCH_HAS_REFCOUNT for the time being
futex: Remove duplicated code and fix undefined behaviour
Documentation/locking/atomic: Finish the document...
locking/lockdep: Fix workqueue crossrelease annotation
workqueue/lockdep: 'Fix' flush_work() annotation
locking/lockdep/selftests: Add mixed read-write ABBA tests
mm, locking/barriers: Clarify tlb_flush_pending() barriers
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE and CONFIG_LOCKDEP_COMPLETIONS truly non-interactive
locking/lockdep: Explicitly initialize wq_barrier::done::map
locking/lockdep: Rename CONFIG_LOCKDEP_COMPLETE to CONFIG_LOCKDEP_COMPLETIONS
locking/lockdep: Reword title of LOCKDEP_CROSSRELEASE config
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE part of CONFIG_PROVE_LOCKING
locking/refcounts, x86/asm: Implement fast refcount overflow protection
locking/lockdep: Fix the rollback and overwrite detection logic in crossrelease
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- fix affine wakeups (Peter Zijlstra)
- improve CPU onlining (and general bootup) scalability on systems
with ridiculous number (thousands) of CPUs (Peter Zijlstra)
- sched/numa updates (Rik van Riel)
- sched/deadline updates (Byungchul Park)
- sched/cpufreq enhancements and related cleanups (Viresh Kumar)
- sched/debug enhancements (Xie XiuQi)
- various fixes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
sched/debug: Optimize sched_domain sysctl generation
sched/topology: Avoid pointless rebuild
sched/topology, cpuset: Avoid spurious/wrong domain rebuilds
sched/topology: Improve comments
sched/topology: Fix memory leak in __sdt_alloc()
sched/completion: Document that reinit_completion() must be called after complete_all()
sched/autogroup: Fix error reporting printk text in autogroup_create()
sched/fair: Fix wake_affine() for !NUMA_BALANCING
sched/debug: Intruduce task_state_to_char() helper function
sched/debug: Show task state in /proc/sched_debug
sched/debug: Use task_pid_nr_ns in /proc/$pid/sched
sched/core: Remove unnecessary initialization init_idle_bootup_task()
sched/deadline: Change return value of cpudl_find()
sched/deadline: Make find_later_rq() choose a closer CPU in topology
sched/numa: Scale scan period with tasks in group and shared/private
sched/numa: Slow down scan rate if shared faults dominate
sched/pelt: Fix false running accounting
sched: Mark pick_next_task_dl() and build_sched_domain() as static
sched/cpupri: Don't re-initialize 'struct cpupri'
sched/deadline: Don't re-initialize 'struct cpudl'
...
|
|
Conflicts:
mm/page_alloc.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"A late but obvious fix for cgroup.
I broke the 'cpuset.memory_pressure' file a long time ago (v4.4) by
accidentally deleting its file index, which made it a duplicate of the
'cpuset.memory_migrate' file. Spotted and fixed by Waiman"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: Fix incorrect memory_pressure control file mapping
|
|
When disabling cpuset.sched_load_balance we expect to be able to online
CPUs without generating sched_domains. However this is currently
completely broken.
What happens is that we generate the sched_domains and then destroy
them. This is because of the spurious 'default' domain build in
cpuset_update_active_cpus(). That builds a single machine wide domain
and then schedules a work to build the 'real' domains. The work then
finds there are _no_ domains and destroys the lot again.
Furthermore, if there actually were cpusets, building the machine wide
domain is actively wrong, because it would allow tasks to 'escape' their
cpuset. Also I don't think its needed, the scheduler really should
respect the active mask.
Reported-by: Ofer Levi(SW) <oferle@mellanox.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet.Gupta1@synopsys.com <Vineet.Gupta1@synopsys.com>
Cc: rusty@rustcorp.com.au <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The memory_pressure control file was incorrectly set up without
a private value (0, by default). As a result, this control
file was treated like memory_migrate on read. By adding back the
FILE_MEMORY_PRESSURE private value, the correct memory pressure value
will be returned.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 7dbdb199d3bf ("cgroup: replace cftype->mode with CFTYPE_WORLD_WRITABLE")
Cc: stable@vger.kernel.org # v4.4+
|
|
Cpuset v2 has some useful behaviors that are not present in v1 because
of backward compatibility concern. One of that is the restoration of
the original cpu and memory node mask after a hot removal and addition
event sequence.
This patch makes the cpuset controller to check the
CGRP_ROOT_CPUSET_V2_MODE flag and use the v2 behavior if it is set.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
A new mount option "cpuset_v2_mode" is added to the v1 cgroupfs
filesystem to enable cpuset controller to use v2 behavior in a v1
cgroup. This mount option applies only to cpuset controller and have
no effect on other controllers.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
"descendants" and "depth" are declared as int, so they can't be larger
than INT_MAX. Static checkers complain and it's slightly confusing for
humans as well so let's just remove these conditions.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Misc trivial changes to prepare for future changes. No functional
difference.
* Expose cgroup_get(), cgroup_tryget() and cgroup_parent().
* Implement task_dfl_cgroup() which dereferences css_set->dfl_cgrp.
* Rename cgroup_stats_show() to cgroup_stat_show() for consistency
with the file name.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Any use of key->enabled (that is static_key_enabled and static_key_count)
outside jump_label_lock should handle its own serialization. In the case
of cpusets_enabled_key, the key is always incremented/decremented under
cpuset_mutex, and hence the same rule applies to nr_cpusets. The rule
*is* respected currently, but the mutex is static so nr_cpusets should
be static too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Zefan Li <lizefan@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1501601046-35683-4-git-send-email-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In codepaths that use the begin/retry interface for reading
mems_allowed_seq with irqs disabled, there exists a race condition that
stalls the patch process after only modifying a subset of the
static_branch call sites.
This problem manifested itself as a deadlock in the slub allocator,
inside get_any_partial. The loop reads mems_allowed_seq value (via
read_mems_allowed_begin), performs the defrag operation, and then
verifies the consistency of mem_allowed via the read_mems_allowed_retry
and the cookie returned by xxx_begin.
The issue here is that both begin and retry first check if cpusets are
enabled via cpusets_enabled() static branch. This branch can be
rewritted dynamically (via cpuset_inc) if a new cpuset is created. The
x86 jump label code fully synchronizes across all CPUs for every entry
it rewrites. If it rewrites only one of the callsites (specifically the
one in read_mems_allowed_retry) and then waits for the
smp_call_function(do_sync_core) to complete while a CPU is inside the
begin/retry section with IRQs off and the mems_allowed value is changed,
we can hang.
This is because begin() will always return 0 (since it wasn't patched
yet) while retry() will test the 0 against the actual value of the seq
counter.
The fix is to use two different static keys: one for begin
(pre_enable_key) and one for retry (enable_key). In cpuset_inc(), we
first bump the pre_enable key to ensure that cpuset_mems_allowed_begin()
always return a valid seqcount if are enabling cpusets. Similarly, when
disabling cpusets via cpuset_dec(), we first ensure that callers of
cpuset_mems_allowed_retry() will start ignoring the seqcount value
before we let cpuset_mems_allowed_begin() return 0.
The relevant stack traces of the two stuck threads:
CPU: 1 PID: 1415 Comm: mkdir Tainted: G L 4.9.36-00104-g540c51286237 #4
Hardware name: Default string Default string/Hardware, BIOS 4.29.1-20170526215256 05/26/2017
task: ffff8817f9c28000 task.stack: ffffc9000ffa4000
RIP: smp_call_function_many+0x1f9/0x260
Call Trace:
smp_call_function+0x3b/0x70
on_each_cpu+0x2f/0x90
text_poke_bp+0x87/0xd0
arch_jump_label_transform+0x93/0x100
__jump_label_update+0x77/0x90
jump_label_update+0xaa/0xc0
static_key_slow_inc+0x9e/0xb0
cpuset_css_online+0x70/0x2e0
online_css+0x2c/0xa0
cgroup_apply_control_enable+0x27f/0x3d0
cgroup_mkdir+0x2b7/0x420
kernfs_iop_mkdir+0x5a/0x80
vfs_mkdir+0xf6/0x1a0
SyS_mkdir+0xb7/0xe0
entry_SYSCALL_64_fastpath+0x18/0xad
...
CPU: 2 PID: 1 Comm: init Tainted: G L 4.9.36-00104-g540c51286237 #4
Hardware name: Default string Default string/Hardware, BIOS 4.29.1-20170526215256 05/26/2017
task: ffff8818087c0000 task.stack: ffffc90000030000
RIP: int3+0x39/0x70
Call Trace:
<#DB> ? ___slab_alloc+0x28b/0x5a0
<EOE> ? copy_process.part.40+0xf7/0x1de0
__slab_alloc.isra.80+0x54/0x90
copy_process.part.40+0xf7/0x1de0
copy_process.part.40+0xf7/0x1de0
kmem_cache_alloc_node+0x8a/0x280
copy_process.part.40+0xf7/0x1de0
_do_fork+0xe7/0x6c0
_raw_spin_unlock_irq+0x2d/0x60
trace_hardirqs_on_caller+0x136/0x1d0
entry_SYSCALL_64_fastpath+0x5/0xad
do_syscall_64+0x27/0x350
SyS_clone+0x19/0x20
do_syscall_64+0x60/0x350
entry_SYSCALL64_slow_path+0x25/0x25
Link: http://lkml.kernel.org/r/20170731040113.14197-1-dmitriyz@waymo.com
Fixes: 46e700abc44c ("mm, page_alloc: remove unnecessary taking of a seqlock when cpusets are disabled")
Signed-off-by: Dima Zavin <dmitriyz@waymo.com>
Reported-by: Cliff Spradlin <cspradlin@waymo.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christopher Lameter <cl@linux.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Each css_set directly points to the default cgroup it belongs to, so
there's no reason to walk the cgrp_links list on the default
hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
As we already have a pointer to the parent cgroup in
cgroup_destroy_locked(), we don't need to calculate it again
to pass as an argument for cgroup1_check_for_release().
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: kernel-team@fb.com
Cc: linux-kernel@vger.kernel.org
|
|
A cgroup can consume resources even after being deleted by a user.
For example, writing back dirty pages should be accounted and
limited, despite the corresponding cgroup might contain no processes
and being deleted by a user.
In the current implementation a cgroup can remain in such "dying" state
for an undefined amount of time. For instance, if a memory cgroup
contains a pge, mlocked by a process belonging to an other cgroup.
Although the lifecycle of a dying cgroup is out of user's control,
it's important to have some insight of what's going on under the hood.
In particular, it's handy to have a counter which will allow
to detect css leaks.
To solve this problem, add a cgroup.stat interface to
the base cgroup control files with the following metrics:
nr_descendants total number of visible descendant cgroups
nr_dying_descendants total number of dying descendant cgroups
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: kernel-team@fb.com
Cc: cgroups@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Creating cgroup hierearchies of unreasonable size can affect
overall system performance. A user might want to limit the
size of cgroup hierarchy. This is especially important if a user
is delegating some cgroup sub-tree.
To address this issue, introduce an ability to control
the size of cgroup hierarchy.
The cgroup.max.descendants control file allows to set the maximum
allowed number of descendant cgroups.
The cgroup.max.depth file controls the maximum depth of the cgroup
tree. Both are single value r/w files, with "max" default value.
The control files exist on each hierarchy level (including root).
When a new cgroup is created, we check the total descendants
and depth limits on each level, and if none of them are exceeded,
a new cgroup is created.
Only alive cgroups are counted, removed (dying) cgroups are
ignored.
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: kernel-team@fb.com
Cc: cgroups@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
Keep track of the number of online and dying descent cgroups.
This data will be used later to add an ability to control cgroup
hierarchy (limit the depth and the number of descent cgroups)
and display hierarchy stats.
Signed-off-by: Roman Gushchin <guro@fb.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: kernel-team@fb.com
Cc: cgroups@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
By default we output cgroup id in blktrace. This adds an option to
display cgroup path. Since get cgroup path is a relativly heavy
operation, we don't enable it by default.
with the option enabled, blktrace will output something like this:
dd-1353 [007] d..2 293.015252: 8,0 /test/level D R 24 + 8 [dd]
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now we have the facilities to implement exportfs operations. The idea is
cgroup can export the fhandle info to userspace, then userspace uses
fhandle to find the cgroup name. Another example is userspace can get
fhandle for a cgroup and BPF uses the fhandle to filter info for the
cgroup.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Explain cgroup_enable_threaded() and note that the function can never
be called on the root cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Waiman Long <longman@redhat.com>
|
|
cgroup_enable_threaded() checks that the cgroup doesn't have any tasks
or children and fails the operation if so. This test is unnecessary
because the first part is already checked by
cgroup_can_be_thread_root() and the latter is unnecessary. The latter
actually cause a behavioral oddity. Please consider the following
hierarchy. All cgroups are domains.
A
/ \
B C
\
D
If B is made threaded, C and D becomes invalid domains. Due to the no
children restriction, threaded mode can't be enabled on C. For C and
D, the only thing the user can do is removal.
There is no reason for this restriction. Remove it.
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
While refactoring, f7b2814bb9b6 ("cgroup: factor out
cgroup_{apply|finalize}_control() from
cgroup_subtree_control_write()") broke error return value from the
function. The return value from the last operation is always
overridden to zero. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Update debug controller so that it prints out debug info about thread
mode.
1) The relationship between proc_cset and threaded_csets are displayed.
2) The status of being a thread root or threaded cgroup is displayed.
This patch is extracted from Waiman's larger patch.
v2: - Removed [thread root] / [threaded] from debug.cgroup_css_links
file as the same information is available from cgroup.type.
Suggested by Waiman.
- Threaded marking is moved to the previous patch.
Patch-originally-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch implements cgroup v2 thread support. The goal of the
thread mode is supporting hierarchical accounting and control at
thread granularity while staying inside the resource domain model
which allows coordination across different resource controllers and
handling of anonymous resource consumptions.
A cgroup is always created as a domain and can be made threaded by
writing to the "cgroup.type" file. When a cgroup becomes threaded, it
becomes a member of a threaded subtree which is anchored at the
closest ancestor which isn't threaded.
The threads of the processes which are in a threaded subtree can be
placed anywhere without being restricted by process granularity or
no-internal-process constraint. Note that the threads aren't allowed
to escape to a different threaded subtree. To be used inside a
threaded subtree, a controller should explicitly support threaded mode
and be able to handle internal competition in the way which is
appropriate for the resource.
The root of a threaded subtree, the nearest ancestor which isn't
threaded, is called the threaded domain and serves as the resource
domain for the whole subtree. This is the last cgroup where domain
controllers are operational and where all the domain-level resource
consumptions in the subtree are accounted. This allows threaded
controllers to operate at thread granularity when requested while
staying inside the scope of system-level resource distribution.
As the root cgroup is exempt from the no-internal-process constraint,
it can serve as both a threaded domain and a parent to normal cgroups,
so, unlike non-root cgroups, the root cgroup can have both domain and
threaded children.
Internally, in a threaded subtree, each css_set has its ->dom_cset
pointing to a matching css_set which belongs to the threaded domain.
This ensures that thread root level cgroup_subsys_state for all
threaded controllers are readily accessible for domain-level
operations.
This patch enables threaded mode for the pids and perf_events
controllers. Neither has to worry about domain-level resource
consumptions and it's enough to simply set the flag.
For more details on the interface and behavior of the thread mode,
please refer to the section 2-2-2 in Documentation/cgroup-v2.txt added
by this patch.
v5: - Dropped silly no-op ->dom_cgrp init from cgroup_create().
Spotted by Waiman.
- Documentation updated as suggested by Waiman.
- cgroup.type content slightly reformatted.
- Mark the debug controller threaded.
v4: - Updated to the general idea of marking specific cgroups
domain/threaded as suggested by PeterZ.
v3: - Dropped "join" and always make mixed children join the parent's
threaded subtree.
v2: - After discussions with Waiman, support for mixed thread mode is
added. This should address the issue that Peter pointed out
where any nesting should be avoided for thread subtrees while
coexisting with other domain cgroups.
- Enabling / disabling thread mode now piggy backs on the existing
control mask update mechanism.
- Bug fixes and cleanup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
cgroup v2 is in the process of growing thread granularity support.
Once thread mode is enabled, the root cgroup of the subtree serves as
the dom_cgrp to which the processes of the subtree conceptually belong
and domain-level resource consumptions not tied to any specific task
are charged. In the subtree, threads won't be subject to process
granularity or no-internal-task constraint and can be distributed
arbitrarily across the subtree.
This patch implements a new task iterator flag CSS_TASK_ITER_THREADED,
which, when used on a dom_cgrp, makes the iteration include the tasks
on all the associated threaded css_sets. "cgroup.procs" read path is
updated to use it so that reading the file on a proc_cgrp lists all
processes. This will also be used by controller implementations which
need to walk processes or tasks at the resource domain level.
Task iteration is implemented nested in css_set iteration. If
CSS_TASK_ITER_THREADED is specified, after walking tasks of each
!threaded css_set, all the associated threaded css_sets are visited
before moving onto the next !threaded css_set.
v2: ->cur_pcset renamed to ->cur_dcset. Updated for the new
enable-threaded-per-cgroup behavior.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
cgroup v2 is in the process of growing thread granularity support. A
threaded subtree is composed of a thread root and threaded cgroups
which are proper members of the subtree.
The root cgroup of the subtree serves as the domain cgroup to which
the processes (as opposed to threads / tasks) of the subtree
conceptually belong and domain-level resource consumptions not tied to
any specific task are charged. Inside the subtree, threads won't be
subject to process granularity or no-internal-task constraint and can
be distributed arbitrarily across the subtree.
This patch introduces cgroup->dom_cgrp along with threaded css_set
handling.
* cgroup->dom_cgrp points to self for normal and thread roots. For
proper thread subtree members, points to the dom_cgrp (the thread
root).
* css_set->dom_cset points to self if for normal and thread roots. If
threaded, points to the css_set which belongs to the cgrp->dom_cgrp.
The dom_cgrp serves as the resource domain and keeps the matching
csses available. The dom_cset holds those csses and makes them
easily accessible.
* All threaded csets are linked on their dom_csets to enable iteration
of all threaded tasks.
* cgroup->nr_threaded_children keeps track of the number of threaded
children.
This patch adds the above but doesn't actually use them yet. The
following patches will build on top.
v4: ->nr_threaded_children added.
v3: ->proc_cgrp/cset renamed to ->dom_cgrp/cset. Updated for the new
enable-threaded-per-cgroup behavior.
v2: Added cgroup_is_threaded() helper.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
css_task_iter currently always walks all tasks. With the scheduled
cgroup v2 thread support, the iterator would need to handle multiple
types of iteration. As a preparation, add @flags to
css_task_iter_start() and implement CSS_TASK_ITER_PROCS. If the flag
is not specified, it walks all tasks as before. When asserted, the
iterator only walks the group leaders.
For now, the only user of the flag is cgroup v2 "cgroup.procs" file
which no longer needs to skip non-leader tasks in cgroup_procs_next().
Note that cgroup v1 "cgroup.procs" can't use the group leader walk as
v1 "cgroup.procs" doesn't mean "list all thread group leaders in the
cgroup" but "list all thread group id's with any threads in the
cgroup".
While at it, update cgroup_procs_show() to use task_pid_vnr() instead
of task_tgid_vnr(). As the iteration guarantees that the function
only sees group leaders, this doesn't change the output and will allow
sharing the function for thread iteration.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Currently, writes "cgroup.procs" and "cgroup.tasks" files are all
handled by __cgroup_procs_write() on both v1 and v2. This patch
reoragnizes the write path so that there are common helper functions
that different write paths use.
While this somewhat increases LOC, the different paths are no longer
intertwined and each path has more flexibility to implement different
behaviors which will be necessary for the planned v2 thread support.
v3: - Restructured so that cgroup_procs_write_permission() takes
@src_cgrp and @dst_cgrp.
v2: - Rolled in Waiman's task reference count fix.
- Updated on top of nsdelegate changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
|
|
On subsystem registration, css_populate_dir() is not called on the new
root css, so the interface files for the subsystem on cgrp_dfl_root
aren't created on registration. This is a residue from the days when
cgrp_dfl_root was used only as the parking spot for unused subsystems,
which no longer is true as it's used as the root for cgroup2.
This is often fine as later operations tend to create them as a part
of mount (cgroup1) or subtree_control operations (cgroup2); however,
it's not difficult to mount cgroup2 with the controller interface
files missing as Waiman found out.
Fix it by invoking css_populate_dir() on the root css on subsys
registration.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
cgrp->nr_populated_csets
Implement trivial cgroup_has_tasks() which tests whether
cgrp->nr_populated_csets is zero and replace the explicit local
populated test in cgroup_subtree_control(). This simplifies the code
and cgroup_has_tasks() will be used in more places later.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
cgrp->populated_cnt counts both local (the cgroup's populated
css_sets) and subtree proper (populated children) so that it's only
zero when the whole subtree, including self, is empty.
This patch splits the counter into two so that local and children
populated states are tracked separately. It allows finer-grained
tests on the state of the hierarchy which will be used to replace
css_set walking local populated test.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Subsystem migration methods shouldn't be called for empty migrations.
cgroup_migrate_execute() implements this guarantee by bailing early if
there are no source css_sets. This used to be correct before
a79a908fd2b0 ("cgroup: introduce cgroup namespaces"), but no longer
since the commit because css_sets can stay pinned without tasks in
them.
This caused cgroup_migrate_execute() call into cpuset migration
methods with an empty cgroup_taskset. cpuset migration methods
correctly assume that cgroup_taskset_first() never returns NULL;
however, due to the bug, it can, leading to the following oops.
Unable to handle kernel paging request for data at address 0x00000960
Faulting instruction address: 0xc0000000001d6868
Oops: Kernel access of bad area, sig: 11 [#1]
...
CPU: 14 PID: 16947 Comm: kworker/14:0 Tainted: G W
4.12.0-rc4-next-20170609 #2
Workqueue: events cpuset_hotplug_workfn
task: c00000000ca60580 task.stack: c00000000c728000
NIP: c0000000001d6868 LR: c0000000001d6858 CTR: c0000000001d6810
REGS: c00000000c72b720 TRAP: 0300 Tainted: GW (4.12.0-rc4-next-20170609)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 44722422 XER: 20000000
CFAR: c000000000008710 DAR: 0000000000000960 DSISR: 40000000 SOFTE: 1
GPR00: c0000000001d6858 c00000000c72b9a0 c000000001536e00 0000000000000000
GPR04: c00000000c72b9c0 0000000000000000 c00000000c72bad0 c000000766367678
GPR08: c000000766366d10 c00000000c72b958 c000000001736e00 0000000000000000
GPR12: c0000000001d6810 c00000000e749300 c000000000123ef8 c000000775af4180
GPR16: 0000000000000000 0000000000000000 c00000075480e9c0 c00000075480e9e0
GPR20: c00000075480e8c0 0000000000000001 0000000000000000 c00000000c72ba20
GPR24: c00000000c72baa0 c00000000c72bac0 c000000001407248 c00000000c72ba20
GPR28: c00000000141fc80 c00000000c72bac0 c00000000c6bc790 0000000000000000
NIP [c0000000001d6868] cpuset_can_attach+0x58/0x1b0
LR [c0000000001d6858] cpuset_can_attach+0x48/0x1b0
Call Trace:
[c00000000c72b9a0] [c0000000001d6858] cpuset_can_attach+0x48/0x1b0 (unreliable)
[c00000000c72ba00] [c0000000001cbe80] cgroup_migrate_execute+0xb0/0x450
[c00000000c72ba80] [c0000000001d3754] cgroup_transfer_tasks+0x1c4/0x360
[c00000000c72bba0] [c0000000001d923c] cpuset_hotplug_workfn+0x86c/0xa20
[c00000000c72bca0] [c00000000011aa44] process_one_work+0x1e4/0x580
[c00000000c72bd30] [c00000000011ae78] worker_thread+0x98/0x5c0
[c00000000c72bdc0] [c000000000124058] kthread+0x168/0x1b0
[c00000000c72be30] [c00000000000b2e8] ret_from_kernel_thread+0x5c/0x74
Instruction dump:
f821ffa1 7c7d1b78 60000000 60000000 38810020 7fa3eb78 3f42ffed 4bff4c25
60000000 3b5a0448 3d420020 eb610020 <e9230960> 7f43d378 e9290000 f92af200
---[ end trace dcaaf98fb36d9e64 ]---
This patch fixes the bug by adding an explicit nr_tasks counter to
cgroup_taskset and skipping calling the migration methods if the
counter is zero. While at it, remove the now spurious check on no
source css_sets.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: stable@vger.kernel.org # v4.6+
Fixes: a79a908fd2b0 ("cgroup: introduce cgroup namespaces")
Link: http://lkml.kernel.org/r/1497266622.15415.39.camel@abdul.in.ibm.com
|
|
When updating task's mems_allowed and rebinding its mempolicy due to
cpuset's mems being changed, we currently only take the seqlock for
writing when either the task has a mempolicy, or the new mems has no
intersection with the old mems.
This should be enough to prevent a parallel allocation seeing no
available nodes, but the optimization is IMHO unnecessary (cpuset
updates should not be frequent), and we still potentially risk issues if
the intersection of new and old nodes has limited amount of
free/reclaimable memory.
Let's just use the seqlock for all tasks.
Link: http://lkml.kernel.org/r/20170517081140.30654-6-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit c0ff7453bb5c ("cpuset,mm: fix no node to alloc memory when
changing cpuset's mems") has introduced a two-step protocol when
rebinding task's mempolicy due to cpuset update, in order to avoid a
parallel allocation seeing an empty effective nodemask and failing.
Later, commit cc9a6c877661 ("cpuset: mm: reduce large amounts of memory
barrier related damage v3") introduced a seqlock protection and removed
the synchronization point between the two update steps. At that point
(or perhaps later), the two-step rebinding became unnecessary.
Currently it only makes sure that the update first adds new nodes in
step 1 and then removes nodes in step 2. Without memory barriers the
effects are questionable, and even then this cannot prevent a parallel
zonelist iteration checking the nodemask at each step to observe all
nodes as unusable for allocation. We now fully rely on the seqlock to
prevent premature OOMs and allocation failures.
We can thus remove the two-step update parts and simplify the code.
Link: http://lkml.kernel.org/r/20170517081140.30654-5-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, cgroup only supports delegation to !root users and cgroup
namespaces don't get any special treatments. This limits the
usefulness of cgroup namespaces as they by themselves can't be safe
delegation boundaries. A process inside a cgroup can change the
resource control knobs of the parent in the namespace root and may
move processes in and out of the namespace if cgroups outside its
namespace are visible somehow.
This patch adds a new mount option "nsdelegate" which makes cgroup
namespaces delegation boundaries. If set, cgroup behaves as if write
permission based delegation took place at namespace boundaries -
writes to the resource control knobs from the namespace root are
denied and migration crossing the namespace boundary aren't allowed
from inside the namespace.
This allows cgroup namespace to function as a delegation boundary by
itself.
v2: Silently ignore nsdelegate specified on !init mounts.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Aravind Anbudurai <aru7@fb.com>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Eric Biederman <ebiederm@xmission.com>
|
|
Restructure cgroup_procs_write_permission() to make extending
permission logic easier.
This patch doesn't cause any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The debug controller grabs cgroup_mutex from interface file show
functions which can deadlock and triggers lockdep warnings. Fix it by
using cgroup_kn_lock_live()/cgroup_kn_unlock() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
|
|
Factor out cgroup_masks_read_one() out of cgroup_masks_read() for
simplicity.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
|
|
Make debug an implicit controller on cgroup2 which is enabled by
"cgroup_debug" boot param.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
|
