| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch is to add debugfs support for ptp_qoriq. Current debugfs
supports to control fiper1/fiper2 loopback mode. If the loopback mode
is enabled, the fiper1/fiper2 pulse is looped back into trigger1/
trigger2 input. This is very useful for validating hardware and driver
without external hardware. Below is an example to enable fiper1 loopback.
echo 1 > /sys/kernel/debug/2d10e00.ptp_clock/fiper1-loopback
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The external trigger stamp FIFO was introduced as a new feature
for QorIQ 1588 timer IP block. This patch is to support it by
adding a new dts property "fsl,extts-fifo". Any QorIQ 1588 timer
supporting this feature is required to add this property in its
dts node.
In addition, the FIFO should be cleaned up before enabling external
trigger interrupts. Otherwise, there will be interrupts immediately
just after enabling external trigger interrupts.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Next to snooping IGMP/MLD queries RFC4541, section 2.1.1.a) recommends
to snoop multicast router advertisements to detect multicast routers.
Multicast router advertisements are sent to an "all-snoopers"
multicast address. To be able to receive them reliably, we need to
join this group.
Otherwise other snooping switches might refrain from forwarding these
advertisements to us.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for extended statistics (xstats) call to the
bonding. The first user would be the 3ad code which counts the following
events:
- LACPDU Rx/Tx
- LACPDU unknown type Rx
- LACPDU illegal Rx
- Marker Rx/Tx
- Marker response Rx/Tx
- Marker unknown type Rx
All of these are exported via netlink as separate attributes to be
easily extensible as we plan to add more in the future.
Similar to how the bridge and other xstats exports, the structure
inside is:
[ IFLA_STATS_LINK_XSTATS ]
-> [ LINK_XSTATS_TYPE_BOND ]
-> [ BOND_XSTATS_3AD ]
-> [ 3ad stats attributes ]
With this structure it's easy to add more stat types later.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Count the following types of 3ad packets per slave:
- rx/tx lacpdu
- rx/tx marker
- rx/tx marker response
- rx illegal lacpdus (right now counted on wrong length)
- rx unknown lacpdu type
- rx unknown marker type
The counters are using atomic64 since this is not fast path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There have been many people complaining about the inconsistent
behaviors of IPv4 and IPv6 devconf when creating new network
namespaces. Currently, for IPv4, we inherit all current settings
from init_net, but for IPv6 we reset all setting to default.
This patch introduces a new /proc file
/proc/sys/net/core/devconf_inherit_init_net to control the
behavior of whether to inhert sysctl current settings from init_net.
This file itself is only available in init_net.
As demonstrated below:
Initial setup in init_net:
# cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# cat /proc/sys/net/ipv6/conf/all/accept_dad
1
Default value 0 (current behavior):
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
0
Set to 1 (inherit from init_net):
# echo 1 > /proc/sys/net/core/devconf_inherit_init_net
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
1
Set to 2 (reset to default):
# echo 2 > /proc/sys/net/core/devconf_inherit_init_net
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
0
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
0
Set to a value out of range (invalid):
# echo 3 > /proc/sys/net/core/devconf_inherit_init_net
-bash: echo: write error: Invalid argument
# echo -1 > /proc/sys/net/core/devconf_inherit_init_net
-bash: echo: write error: Invalid argument
Reported-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Reported-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix endless loop in nf_tables, from Phil Sutter.
2) Fix cross namespace ip6_gre tunnel hash list corruption, from
Olivier Matz.
3) Don't be too strict in phy_start_aneg() otherwise we might not allow
restarting auto negotiation. From Heiner Kallweit.
4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.
5) Memory leak in act_tunnel_key, from Davide Caratti.
6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.
7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.
8) Missing udplite rehash callbacks, from Alexey Kodanev.
9) Log dirty pages properly in vhost, from Jason Wang.
10) Use consume_skb() in neigh_probe() as this is a normal free not a
drop, from Yang Wei. Likewise in macvlan_process_broadcast().
11) Missing device_del() in mdiobus_register() error paths, from Thomas
Petazzoni.
12) Fix checksum handling of short packets in mlx5, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
bpf: in __bpf_redirect_no_mac pull mac only if present
virtio_net: bulk free tx skbs
net: phy: phy driver features are mandatory
isdn: avm: Fix string plus integer warning from Clang
net/mlx5e: Fix cb_ident duplicate in indirect block register
net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
net/mlx5e: Fix wrong error code return on FEC query failure
net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
tools: bpftool: Cleanup license mess
bpf: fix inner map masking to prevent oob under speculation
bpf: pull in pkt_sched.h header for tooling to fix bpftool build
selftests: forwarding: Add a test case for externally learned FDB entries
selftests: mlxsw: Test FDB offload indication
mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
net: bridge: Mark FDB entries that were added by user as such
mlxsw: spectrum_fid: Update dummy FID index
mlxsw: pci: Return error on PCI reset timeout
mlxsw: pci: Increase PCI SW reset timeout
mlxsw: pci: Ring CQ's doorbell before RDQ's
MAINTAINERS: update email addresses of liquidio driver maintainers
...
|
|
Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
"Fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: Use copy_to_iter() to send control queue response
vhost: return EINVAL if iovecs size does not match the message size
virtio-balloon: tweak config_changed implementation
virtio: don't allocate vqs when names[i] = NULL
virtio_pci: use queue idx instead of array idx to set up the vq
virtio: document virtio_config_ops restrictions
virtio: fix virtio_config_ops description
|
|
'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux
Pull misc clang fixes from Miguel Ojeda:
- A fix for OPTIMIZER_HIDE_VAR from Michael S Tsirkin
- Update clang-format with the latest for_each macro list from Jason
Gunthorpe
* tag 'compiler-attributes-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
include/linux/compiler*.h: fix OPTIMIZER_HIDE_VAR
* tag 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
clang-format: Update .clang-format with the latest for_each macro list
|
|
Similar to u32 filter, it is useful to know how many times
we reach each basic filter and how many times we pass the
ematch attached to it.
Sample output:
filter protocol arp pref 49152 basic chain 0
filter protocol arp pref 49152 basic chain 0 handle 0x1 (rule hit 3 success 3)
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1 installed 81 sec used 4 sec
Action statistics:
Sent 126 bytes 3 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
- Fix IPI handling for Lantiq SoCs, which was broken by changes made
back in v4.12.
- Enable OF/DT serial support in ath79_defconfig to give us working
serial by default.
- Fix 64b builds for the Jazz platform.
- Set up a struct device for the BCM47xx SoC to allow BCM47xx drivers
to perform DMA again following the major DMA mapping changes made in
v4.19.
- Disable MSI on Cavium Octeon systems when the pcie_disable command
line parameter introduced in v3.3 is used, in order to avoid
inadvetently accessing PCIe controller registers despite the command
line.
- Fix a build failure for Cavium Octeon kernels with kexec enabled,
introduced in v4.20.
- Fix a regression in the behaviour of semctl/shmctl/msgctl IPC
syscalls for kernels including n32 support but not o32 support caused
by some cleanup in v3.19.
* tag 'mips_fixes_5.0_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: OCTEON: fix kexec support
mips: fix n32 compat_ipc_parse_version
Disable MSI also when pcie-octeon.pcie_disable on
MIPS: BCM47XX: Setup struct device for the SoC
MIPS: jazz: fix 64bit build
MIPS: ath79: Enable OF serial ports in the default config
MIPS: lantiq: Use CP0_LEGACY_COMPARE_IRQ
MIPS: lantiq: Fix IPI interrupt handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A crash fix, a build warning fix, a miscellaneous small cleanups.
In case anyone is looking for them, there was a regression caught by
testing that caused two patches to be dropped from this update. Those
patches have been reworked and will soak for another week / re-target
5.0-rc4.
- Fix driver initialization crash due to the inability to report an
'error' state for a DIMM's security capability.
- Build warning fix for little-endian ARM64 builds
- Fix a potential race between the EDAC driver's usage of the NFIT
SMBIOS id for a DIMM and the driver shutdown path.
- A small collection of one-line benign cleanups for duplicate
variable assignments, a duplicate header include and a mis-typed
function argument"
* tag 'libnvdimm-fixes-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/security: Fix nvdimm_security_state() state request selection
acpi/nfit: Remove duplicate set nd_set in acpi_nfit_init_interleave_set()
acpi/nfit: Fix race accessing memdev in nfit_get_smbios_id()
libnvdimm/dimm: Fix security capability detection for non-Intel NVDIMMs
nfit: Mark some functions as __maybe_unused
ACPI/nfit: delete the function to_acpi_nfit_desc
ACPI/nfit: delete the redundant header file
|
|
Dumps can read state of the NETLINK_F_STRICT_CHK flag from
a field in the callback structure. For non-dump GET requests
we need a way to access the state of that flag from a socket.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are now several places where qdisc_tree_reduce_backlog() is called
with a negative number of packets (to signal an increase in number of
packets in the queue). Rather than rely on overflow behaviour, change the
function signature to use signed integers to communicate this usage to
people reading the code.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon error discover, every driver can report it to the devlink health
mechanism via devlink_health_report function, using the appropriate
reporter registered to it. Driver can pass error specific context which
will be delivered to it as part of the dump / recovery callbacks.
Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and stored at the reporter instance (as long
as there is no other dump which is already stored)
* Auto recovery attempt is being done. depends on:
- Auto Recovery configuration
- Grace period vs. time since last recover
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink health reporter is an instance for reporting, diagnosing and
recovering from run time errors discovered by the reporters.
Define it's data structure and supported operations.
In addition, expose devlink API to create and destroy a reporter.
Each devlink instance will hold it's own reporters list.
As part of the allocation, driver shall provide a set of callbacks which
will be used the devlink in order to handle health reports and user
commands related to this reporter. In addition, driver is entitled to
provide some priv pointer, which can be fetched from the reporter by
devlink_health_reporter_priv function.
For each reporter, devlink will hold a metadata of statistics,
buffers and status.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink health buffer is a mechanism to pass descriptors between drivers
and devlink. The API allows the driver to add objects, object pair,
value array (nested attributes), value and name.
Driver can use this API to fill the buffers in a format which can be
translated by the devlink to the netlink message.
In order to fulfill it, an internal buffer descriptor is defined. This
will hold the data and metadata per each attribute and by used to pass
actual commands to the netlink.
This mechanism will be later used in devlink health for dump and diagnose
data store by the drivers.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although matchall always matches packets, however, it still
relies on a protocol match first. So it is still useful to have
such a counter for matchall. Of course, unlike u32, every time
we hit a matchall filter, it is always a success, so we don't
have to distinguish them.
Sample output:
filter protocol 802.1Q pref 100 matchall chain 0
filter protocol 802.1Q pref 100 matchall chain 0 handle 0x1
not_in_hw (rule hit 10)
action order 1: vlan pop continue
index 1 ref 1 bind 1 installed 40 sec used 1 sec
Action statistics:
Sent 836 bytes 10 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupts have been disabled in phy_stop() already. So we can remove
phy_stop_interrupts() and free the interrupt in phy_disconnect()
directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since tcp_mmap() is defined when CONFIG_MMU is set.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since recent changes to the phylib state machine state PHY_CHANGELINK
isn't used any longer. Therefore let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- fix stack memory leak in omap2fb driver (Vlad Tsyrklevich)
- fix OF node name handling v4.20 regression in offb driver (Rob
Herring)
- convert CONFIG_FB_LOGO_CENTER config option added in v5.0-rc1 into a
kernel parameter (Peter Rosin)
* tag 'fbdev-v5.0-rc3' of git://github.com/bzolnier/linux:
fbdev: fbmem: convert CONFIG_FB_LOGO_CENTER into a cmd line option
fbdev: offb: Fix OF node name handling
omap2fb: Fix stack memory disclosure
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull rdma fixes frfom Jason Gunthorpe:
"Not much so far. We have the usual batch of bugs and two fixes to code
merged this cycle:
- Restore valgrind support for the ioctl verbs interface merged this
window, and fix a missed error code on an error path from that
conversion
- A user reported crash on obsolete mthca hardware
- pvrdma was using the wrong command opcode toward the hypervisor
- NULL pointer crash regression when dumping rdma-cm over netlink
- Be conservative about exposing the global rkey"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/uverbs: Mark ioctl responses with UVERBS_ATTR_F_VALID_OUTPUT
RDMA/mthca: Clear QP objects during their allocation
RDMA/vmw_pvrdma: Return the correct opcode when creating WR
RDMA/cma: Add cm_id restrack resource based on kernel or user cm_id type
RDMA/nldev: Don't expose unsafe global rkey to regular user
RDMA/uverbs: Fix post send success return value in case of error
|
|
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are four sources of VXLAN switchdev notifier calls:
- the changelink() link operation, which already supports extack,
- ndo_fdb_add() which got extack support in a previous patch,
- FDB updates due to packet forwarding,
- and vxlan_fdb_replay().
Extend vxlan_fdb_switchdev_call_notifiers() to include extack in the
switchdev message that it sends, and propagate the argument upwards to
the callers. For the first two cases, pass in the extack gotten through
the operation. For case #3, pass in NULL.
To cover the last case, extend vxlan_fdb_replay() to take extack
argument, which might come from whatever operation necessitated the FDB
replay.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This introduces a new generic SOL_SOCKET-level socket option called
SO_BINDTOIFINDEX. It behaves similar to SO_BINDTODEVICE, but takes a
network interface index as argument, rather than the network interface
name.
User-space often refers to network-interfaces via their index, but has
to temporarily resolve it to a name for a call into SO_BINDTODEVICE.
This might pose problems when the network-device is renamed
asynchronously by other parts of the system. When this happens, the
SO_BINDTODEVICE might either fail, or worse, it might bind to the wrong
device.
In most cases user-space only ever operates on devices which they
either manage themselves, or otherwise have a guarantee that the device
name will not change (e.g., devices that are UP cannot be renamed).
However, particularly in libraries this guarantee is non-obvious and it
would be nice if that race-condition would simply not exist. It would
make it easier for those libraries to operate even in situations where
the device-name might change under the hood.
A real use-case that we recently hit is trying to start the network
stack early in the initrd but make it survive into the real system.
Existing distributions rename network-interfaces during the transition
from initrd into the real system. This, obviously, cannot affect
devices that are up and running (unless you also consider moving them
between network-namespaces). However, the network manager now has to
make sure its management engine for dormant devices will not run in
parallel to these renames. Particularly, when you offload operations
like DHCP into separate processes, these might setup their sockets
early, and thus have to resolve the device-name possibly running into
this race-condition.
By avoiding a call to resolve the device-name, we no longer depend on
the name and can run network setup of dormant devices in parallel to
the transition off the initrd. The SO_BINDTOIFINDEX ioctl plugs this
race.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes recvmsg() to be able to peek across multiple tls records.
Without this patch, the tls's selftests test case
'recv_peek_large_buf_mult_recs' fails. Each tls receive context now
maintains a 'rx_list' to retain incoming skb carrying tls records. If a
tls record needs to be retained e.g. for peek case or for the case when
the buffer passed to recvmsg() has a length smaller than decrypted
record length, then it is added to 'rx_list'. Additionally, records are
added in 'rx_list' if the crypto operation runs in async mode. The
records are dequeued from 'rx_list' after the decrypted data is consumed
by copying into the buffer passed to recvmsg(). In case, the MSG_PEEK
flag is used in recvmsg(), then records are not consumed or removed
from the 'rx_list'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are already checking in phy_detach() that the PHY driver is of
generic kind (1G or 10G) and we are going to make use of that in the SFP
layer as well for 1000BaseT SFP modules, so expose helper functions to
return that information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
b53 and mv88e6xxx support passing platform_data, and now that we have
split the platform_data portion from the main net/dsa.h header file,
include only the relevant parts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of having net/dsa.h contain both the internal switch tree/driver
structures, split the relevant platform_data parts into
include/linux/platform_data/dsa.h and make that header be included by
net/dsa.h in order not to break any setup. A subsequent set of patches
will update code including net/dsa.h to include only the platform_data
header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
"Here's a set of fixes for AFS:
- Use struct_size() for kzalloc() size calculation.
- When calling YFS.CreateFile rather than AFS.CreateFile, it is
possible to create a file with a file lock already held. The
default value indicating no lock required is actually -1, not 0.
- Fix an oops in inode/vnode validation if the target inode doesn't
have a server interest assigned (ie. a server that will notify us
of changes by third parties).
- Fix refcounting of keys in file locking.
- Fix a race in refcounting asynchronous operations in the event of
an error during request transmission. The provision of a dedicated
function to get an extra ref on a call is split into a separate
commit"
* tag 'afs-fixes-20190117' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix race in async call refcounting
afs: Provide a function to get a ref on a call
afs: Fix key refcounting in file locking code
afs: Don't set vnode->cb_s_break in afs_validate()
afs: Set correct lock type for the yfs CreateFile
afs: Use struct_size() in kzalloc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- Remove now unused struct device_node.type pointer
- Fix meson-axg reset header SPDX tag
- Add missing of_node_put in of_graph_get_remote_port_parent
- Fix several binding doc file references and typos
* tag 'devicetree-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: reset: meson-axg: fix SPDX license id
dt-bindings: soc: qcom: Fix trivial language typos
doc: gpio-mvebu: fix broken reference to cp110-system-controller0.txt file
OF: properties: add missing of_node_put
doc: bindings: fix bad reference to ARM CPU bindings
dt-bindings: marvell,mmp2: fix typos in bindings doc
of: Remove struct device_node.type pointer
|
|
There's a race between afs_make_call() and afs_wake_up_async_call() in the
case that an error is returned from rxrpc_kernel_send_data() after it has
queued the final packet.
afs_make_call() will try and clean up the mess, but the call state may have
been moved on thereby causing afs_process_async_call() to also try and to
delete the call.
Fix this by:
(1) Getting an extra ref for an asynchronous call for the call itself to
hold. This makes sure the call doesn't evaporate on us accidentally
and will allow the call to be retained by the caller in a future
patch. The ref is released on leaving afs_make_call() or
afs_wait_for_call_to_complete().
(2) In the event of an error from rxrpc_kernel_send_data():
(a) Don't set the call state to AFS_CALL_COMPLETE until *after* the
call has been aborted and ended. This prevents
afs_deliver_to_call() from doing anything with any notifications
it gets.
(b) Explicitly end the call immediately to prevent further callbacks.
(c) Cancel any queued async_work and wait for the work if it's
executing. This allows us to be sure the race won't recur when we
change the state. We put the work queue's ref on the call if we
managed to cancel it.
(d) Put the call's ref that we got in (1). This belongs to us as long
as the call is in state AFS_CALL_CL_REQUESTING.
Fixes: 341f741f04be ("afs: Refcount the afs_call struct")
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported, the SPDX license id is not placed correctly and the variant
of the BSD License used should be specified.
Fixes: c16292578ffa ("dt-bindings: reset: Add bindings for the Meson-AXG SoC Reset Controller")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
A command line option is much more flexible than a config option and
the supporting code is small. Gets rid of #ifdefs in the code too...
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Commit 65cab850f0ee ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.
Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0ee ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
