| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
swap can do cluster discard for SSD, which is good, but there are some
problems here:
1. swap do the discard just before page reclaim gets a swap entry and
writes the disk sectors. This is useless for high end SSD, because an
overwrite to a sector implies a discard to original sector too. A
discard + overwrite == overwrite.
2. the purpose of doing discard is to improve SSD firmware garbage
collection. Idealy we should send discard as early as possible, so
firmware can do something smart. Sending discard just after swap entry
is freed is considered early compared to sending discard before write.
Of course, if workload is already bound to gc speed, sending discard
earlier or later doesn't make
3. block discard is a sync API, which will delay scan_swap_map()
significantly.
4. Write and discard command can be executed parallel in PCIe SSD.
Making swap discard async can make execution more efficiently.
This patch makes swap discard async and moves discard to where swap entry
is freed. Discard and write have no dependence now, so above issues can
be avoided. Idealy we should do discard for any freed sectors, but some
SSD discard is very slow. This patch still does discard for a whole
cluster.
My test does a several round of 'mmap, write, unmap', which will trigger a
lot of swap discard. In a fusionio card, with this patch, the test
runtime is reduced to 18% of the time without it, so around 5.5x faster.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'm using a fast SSD to do swap. scan_swap_map() sometimes uses up to
20~30% CPU time (when cluster is hard to find, the CPU time can be up to
80%), which becomes a bottleneck. scan_swap_map() scans a byte array to
search a 256 page cluster, which is very slow.
Here I introduced a simple algorithm to search cluster. Since we only
care about 256 pages cluster, we can just use a counter to track if a
cluster is free. Every 256 pages use one int to store the counter. If
the counter of a cluster is 0, the cluster is free. All free clusters
will be added to a list, so searching cluster is very efficient. With
this, scap_swap_map() overhead disappears.
This might help low end SD card swap too. Because if the cluster is
aligned, SD firmware can do flash erase more efficiently.
We only enable the algorithm for SSD. Hard disk swap isn't fast enough
and has downside with the algorithm which might introduce regression (see
below).
The patch slightly changes which cluster is choosen. It always adds free
cluster to list tail. This can help wear leveling for low end SSD too.
And if no cluster found, the scan_swap_map() will do search from the end
of last cluster. So if no cluster found, the scan_swap_map() will do
search from the end of last free cluster, which is random. For SSD, this
isn't a problem at all.
Another downside is the cluster must be aligned to 256 pages, which will
reduce the chance to find a cluster. I would expect this isn't a big
problem for SSD because of the non-seek penality. (And this is the reason
I only enable the algorithm for SSD).
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The previous patch doing vmstats for TLB flushes ("mm: vmstats: tlb flush
counters") effectively missed UP since arch/x86/mm/tlb.c is only compiled
for SMP.
UP systems do not do remote TLB flushes, so compile those counters out on
UP.
arch/x86/kernel/cpu/mtrr/generic.c calls __flush_tlb() directly. This is
probably an optimization since both the mtrr code and __flush_tlb() write
cr4. It would probably be safe to make that a flush_tlb_all() (and then
get these statistics), but the mtrr code is ancient and I'm hesitant to
touch it other than to just stick in the counters.
[akpm@linux-foundation.org: tweak comments]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I was investigating some TLB flush scaling issues and realized that we do
not have any good methods for figuring out how many TLB flushes we are
doing.
It would be nice to be able to do these in generic code, but the
arch-independent calls don't explicitly specify whether we actually need
to do remote flushes or not. In the end, we really need to know if we
actually _did_ global vs. local invalidations, so that leaves us with few
options other than to muck with the counters from arch-specific code.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Simple cleanup. Every user of vma_set_policy() does the same work, this
looks a bit annoying imho. And the new trivial helper which does
mpol_dup() + vma_set_policy() to simplify the callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Read block device partition table from command line. The partition used
for fixed block device (eMMC) embedded device. It is no MBR, save
storage space. Bootloader can be easily accessed by absolute address of
data on the block device. Users can easily change the partition.
This code reference MTD partition, source "drivers/mtd/cmdlinepart.c"
About the partition verbose reference
"Documentation/block/cmdline-partition.txt"
[akpm@linux-foundation.org: fix printk text]
[yongjun_wei@trendmicro.com.cn: fix error return code in parse_parts()]
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: "Wanglin (Albert)" <albert.wanglin@huawei.com>
Cc: Marius Groeger <mag@sysgo.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
same_thread_group/has_group_leader_pid
task_struct->pid/tgid should go away.
1. Change same_thread_group() to use task->signal for comparison.
2. Change has_group_leader_pid(task) to compare task_pid(task) with
signal->leader_pid.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Sergey Dyasly <dserrg@gmail.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert commit c846ef7deba2 ("include/linux/smp.h:on_each_cpu(): switch
back to a macro"). It turns out that the problematic linux/irqflags.h
include was fixed within ia64 and mn10300.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull battery/power supply driver updates from Anton Vorontsov:
"New drivers:
- APM X-Gene system reboot driver by Feng Kan and Loc Ho (APM).
- Qualcomm MSM reboot/poweroff driver by Abhimanyu Kapur (Codeaurora).
- Texas Instruments BQ24190 charger driver by Mark A. Greer (Animal
Creek Technologies).
- Texas Instruments TWL4030 MADC battery driver by Lukas Märdian and
Marek Belisko (Golden Delicious Computers). The driver is used on
Freerunner GTA04 phones.
Highlighted fixes and improvements:
- Suspend/wakeup logic improvements: power supply objects will block
system suspend until all power supply events are processed. Thanks
to Zoran Markovic (Linaro), Arve Hjonnevag and Todd Poynor (Google)"
* tag 'for-v3.12' of git://git.infradead.org/battery-2.6:
rx51_battery: Fix channel number when reading adc value
power: Add twl4030_madc battery driver.
bq24190_charger: Workaround SS definition problem on i386 builds
power_supply: Prevent suspend until power supply events are processed
vexpress-poweroff: Should depend on the required infrastructure
twl4030-charger: Fix compiler warning with regulator_enable()
rx51_battery: Replace hardcoded channels values.
bq24190_charger: Add support for TI BQ24190 Battery Charger
ab8500-charger: We print an unintended error message
max8925_power: Fix missing of_node_put
power_supply: Replace strict_strtol() with kstrtol()
power: Add APM X-Gene system reboot driver
power_supply: tosa_battery: Get rid of irq_to_gpio usage
power supply: collie_battery: Convert to use dev_pm_ops
power_supply: Make goldfish_battery depend on GOLDFISH || COMPILE_TEST
power: reset: Add msm restart support
MAINTAINERS: drivers/power: add entry for SmartReflex AVS drivers
|
|
Pull drm fixes from Dave Airlie:
"Daniel had some fixes queued up, that were delayed, the stolen memory
ones and vga arbiter ones are quite useful, along with his usual bunch
of stuff, nothing for HSW outputs yet.
The one nouveau fix is for a regression I caused with the poweroff stuff"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (30 commits)
drm/nouveau: fix oops on runtime suspend/resume
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
drm/i915: try not to lose backlight CBLV precision
drm/i915: Confine page flips to BCS on Valleyview
drm/i915: Skip stolen region initialisation if none is reserved
drm/i915: fix gpu hang vs. flip stall deadlocks
drm/i915: Hold an object reference whilst we shrink it
drm/i915: fix i9xx_crtc_clock_get for multiplied pixels
drm/i915: handle sdvo input pixel multiplier correctly again
drm/i915: fix hpd work vs. flush_work in the pageflip code deadlock
drm/i915: fix up the relocate_entry refactoring
drm/i915: Fix pipe config warnings when dealing with LVDS fixed mode
drm/i915: Don't call sg_free_table() if sg_alloc_table() fails
i915: Update VGA arbiter support for newer devices
vgaarb: Fix VGA decodes changes
vgaarb: Don't disable resources that are not owned
drm/i915: Pin pages whilst mapping the dma-buf
drm/i915: enable trickle feed on Haswell
x86: add early quirk for reserving Intel graphics stolen memory v5
drm/i915: split PCI IDs out into i915_drm.h v4
...
|
|
Pull nfsd updates from Bruce Fields:
"This was a very quiet cycle! Just a few bugfixes and some cleanup"
* 'nfsd-next' of git://linux-nfs.org/~bfields/linux:
rpc: let xdr layer allocate gssproxy receieve pages
rpc: fix huge kmalloc's in gss-proxy
rpc: comment on linux_cred encoding, treat all as unsigned
rpc: clean up decoding of gssproxy linux creds
svcrpc: remove unused rq_resused
nfsd4: nfsd4_create_clid_dir prints uninitialized data
nfsd4: fix leak of inode reference on delegation failure
Revert "nfsd: nfs4_file_get_access: need to be more careful with O_RDWR"
sunrpc: prepare NFS for 2038
nfsd4: fix setlease error return
nfsd: nfs4_file_get_access: need to be more careful with O_RDWR
|
|
Pull device tree core updates from Grant Likely:
"Generally minor changes. A bunch of bug fixes, particularly for
initialization and some refactoring. Most notable change if feeding
the entire flattened tree into the random pool at boot. May not be
significant, but shouldn't hurt either"
Tim Bird questions whether the boot time cost of the random feeding may
be noticeable. And "add_device_randomness()" is definitely not some
speed deamon of a function.
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/platform: add error reporting to of_amba_device_create()
irq/of: Fix comment typo for irq_of_parse_and_map
of: Feed entire flattened device tree into the random pool
of/fdt: Clean up casting in unflattening path
of/fdt: Remove duplicate memory clearing on FDT unflattening
gpio: implement gpio-ranges binding document fix
of: call __of_parse_phandle_with_args from of_parse_phandle
of: introduce of_parse_phandle_with_fixed_args
of: move of_parse_phandle()
of: move documentation of of_parse_phandle_with_args
of: Fix missing memory initialization on FDT unflattening
of: consolidate definition of early_init_dt_alloc_memory_arch()
of: Make of_get_phy_mode() return int i.s.o. const int
include: dt-binding: input: create a DT header defining key codes.
of/platform: Staticize of_platform_device_create_pdata()
of: Specify initrd location using 64-bit
dt: Typo fix
OF: make of_property_for_each_{u32|string}() use parameters if OF is not enabled
|
|
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper updates from Mike Snitzer:
"Add the ability to collect I/O statistics on user-defined regions of a
device-mapper device. This dm-stats code required the reintroduction
of a div64_u64_rem() helper, but as a separate method that doesn't
slow down div64_u64() -- especially on 32-bit systems.
Allow the error target to replace request-based DM devices (e.g.
multipath) in addition to bio-based DM devices.
Various other small code fixes and improvements to thin-provisioning,
DM cache and the DM ioctl interface"
* tag 'dm-3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm stripe: silence a couple sparse warnings
dm: add statistics support
dm thin: always return -ENOSPC if no_free_space is set
dm ioctl: cleanup error handling in table_load
dm ioctl: increase granularity of type_lock when loading table
dm ioctl: prevent rename to empty name or uuid
dm thin: set pool read-only if breaking_sharing fails block allocation
dm thin: prefix pool error messages with pool device name
dm: allow error target to replace bio-based and request-based targets
math64: New separate div64_u64_rem helper
dm space map: optimise sm_ll_dec and sm_ll_inc
dm btree: prefetch child nodes when walking tree for a dm_btree_del
dm btree: use pop_frame in dm_btree_del to cleanup code
dm cache: eliminate holes in cache structure
dm cache: fix stacking of geometry limits
dm thin: fix stacking of geometry limits
dm thin: add data block size limits to Documentation
dm cache: add data block size limits to code and Documentation
dm cache: document metadata device is exclussive to a cache
dm: stop using WQ_NON_REENTRANT
|
|
Pull md update from Neil Brown:
"Headline item is multithreading for RAID5 so that more IO/sec can be
supported on fast (SSD) devices. Also TILE-Gx SIMD suppor for RAID6
calculations and an assortment of bug fixes"
* tag 'md/3.12' of git://neil.brown.name/md:
raid5: only wakeup necessary threads
md/raid5: flush out all pending requests before proceeding with reshape.
md/raid5: use seqcount to protect access to shape in make_request.
raid5: sysfs entry to control worker thread number
raid5: offload stripe handle to workqueue
raid5: fix stripe release order
raid5: make release_stripe lockless
md: avoid deadlock when dirty buffers during md_stop.
md: Don't test all of mddev->flags at once.
md: Fix apparent cut-and-paste error in super_90_validate
raid6/test: replace echo -e with printf
RAID: add tilegx SIMD implementation of raid6
md: fix safe_mode buglet.
md: don't call md_allow_write in get_bitmap_file.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile 3 (of many) from Al Viro:
"Waiman's conversion of d_path() and bits related to it,
kern_path_mountpoint(), several cleanups and fixes (exportfs
one is -stable fodder, IMO).
There definitely will be more... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
split read_seqretry_or_unlock(), convert d_walk() to resulting primitives
dcache: Translating dentry into pathname without taking rename_lock
autofs4 - fix device ioctl mount lookup
introduce kern_path_mountpoint()
rename user_path_umountat() to user_path_mountpoint_at()
take unlazy_walk() into umount_lookup_last()
Kill indirect include of file.h from eventfd.h, use fdget() in cgroup.c
prune_super(): sb->s_op is never NULL
exportfs: don't assume that ->iterate() won't feed us too long entries
afs: get rid of redundant ->d_name.len checks
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
- Early stolen mem reservation from Jesse in x86 boot code. Acked by Ingo
and hpa. This was ready much earlier but somehow I've thought it'd go
in through x86 trees, hence why this is late. Avoids the pci resource
code to plant mmiobars in the middle of stolen mem and other ugliness.
- vgaarb improvements from Alex Williamson plus the fix from Ville for the
vgacon->fbcon smooth transition "feature".
- Render pageflips on ivb/hsw to avoid stalls due to the ring switching
when only flipping on the blitter (Chris).
- Deadlock fixes around our flush_workqueue which crept back in - lockdep
isn't clever enough :(
- Shrinker recursion fix from Chris - this is the thing that blew the vma
patches from Ben I've taken out of 3.12.
- Fixup for the relocation refactoring. Also an igt testcase to make sure
we don't break this again.
- Pile of smaller fixups all over, shortlog has full details.
* tag 'drm-intel-fixes-2013-09-06' of git://people.freedesktop.org/~danvet/drm-intel: (29 commits)
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
drm/i915: try not to lose backlight CBLV precision
drm/i915: Confine page flips to BCS on Valleyview
drm/i915: Skip stolen region initialisation if none is reserved
drm/i915: fix gpu hang vs. flip stall deadlocks
drm/i915: Hold an object reference whilst we shrink it
drm/i915: fix i9xx_crtc_clock_get for multiplied pixels
drm/i915: handle sdvo input pixel multiplier correctly again
drm/i915: fix hpd work vs. flush_work in the pageflip code deadlock
drm/i915: fix up the relocate_entry refactoring
drm/i915: Fix pipe config warnings when dealing with LVDS fixed mode
drm/i915: Don't call sg_free_table() if sg_alloc_table() fails
i915: Update VGA arbiter support for newer devices
vgaarb: Fix VGA decodes changes
vgaarb: Don't disable resources that are not owned
drm/i915: Pin pages whilst mapping the dma-buf
drm/i915: enable trickle feed on Haswell
x86: add early quirk for reserving Intel graphics stolen memory v5
drm/i915: split PCI IDs out into i915_drm.h v4
i915_gem: Convert kmem_cache_alloc(...GFP_ZERO) to kmem_cache_zalloc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine update from Dan Williams:
"Collection of random updates to the core and some end-driver fixups
for ioatdma and mv_xor:
- NUMA aware channel allocation
- Cleanup dmatest debugfs interface
- ioat: make raid-support Atom only
- mv_xor: big endian
Aside from the top three commits these have all had some soak time in
-next. The top commit fixes a recent build breakage.
It has been a long while since my last pull request, hopefully it does
not show. Thanks to Vinod for keeping an eye on drivers/dma/ this
past year"
* tag 'dmaengine-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: dma_sync_wait and dma_find_channel undefined
MAINTAINERS: update email for Dan Williams
dma: mv_xor: Fix incorrect error path
ioatdma: silence GCC warnings
dmaengine: make dma_channel_rebalance() NUMA aware
dmaengine: make dma_submit_error() return an error code
ioatdma: disable RAID on non-Atom platforms and reenable unaligned copies
mv_xor: support big endian systems using descriptor swap feature
mv_xor: use {readl, writel}_relaxed instead of __raw_{readl, writel}
dmatest: print message on debug level in case of no error
dmatest: remove IS_ERR_OR_NULL checks of debugfs calls
dmatest: make module parameters writable
|
|
dma_sync_wait and dma_find_channel are declared regardless of whether
CONFIG_DMA_ENGINE is enabled, but calling the function without
CONFIG_DMA_ENGINE enabled results "undefined reference" errors.
To get around this, declare dma_sync_wait and dma_find_channel as inline
functions if CONFIG_DMA_ENGINE is undefined.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver update from Kevin Hilman:
"This contains the ARM SoC related driver updates for v3.12. The only
thing this cycle are core PM updates and CPUidle support for ARM's TC2
big.LITTLE development platform"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
cpuidle: big.LITTLE: vexpress-TC2 CPU idle driver
ARM: vexpress: tc2: disable GIC CPU IF in tc2_pm_suspend
drivers: irq-chip: irq-gic: introduce gic_cpu_if_down()
|
|
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
|
|
Pull xfs updates from Ben Myers:
"For 3.12-rc1 there are a number of bugfixes in addition to work to
ease usage of shared code between libxfs and the kernel, the rest of
the work to enable project and group quotas to be used simultaneously,
performance optimisations in the log and the CIL, directory entry file
type support, fixes for log space reservations, some spelling/grammar
cleanups, and the addition of user namespace support.
- introduce readahead to log recovery
- add directory entry file type support
- fix a number of spelling errors in comments
- introduce new Q_XGETQSTATV quotactl for project quotas
- add USER_NS support
- log space reservation rework
- CIL optimisations
- kernel/userspace libxfs rework"
* tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs: (112 commits)
xfs: XFS_MOUNT_QUOTA_ALL needed by userspace
xfs: dtype changed xfs_dir2_sfe_put_ino to xfs_dir3_sfe_put_ino
Fix wrong flag ASSERT in xfs_attr_shortform_getvalue
xfs: finish removing IOP_* macros.
xfs: inode log reservations are too small
xfs: check correct status variable for xfs_inobt_get_rec() call
xfs: inode buffers may not be valid during recovery readahead
xfs: check LSN ordering for v5 superblocks during recovery
xfs: btree block LSN escaping to disk uninitialised
XFS: Assertion failed: first <= last && last < BBTOB(bp->b_length), file: fs/xfs/xfs_trans_buf.c, line: 568
xfs: fix bad dquot buffer size in log recovery readahead
xfs: don't account buffer cancellation during log recovery readahead
xfs: check for underflow in xfs_iformat_fork()
xfs: xfs_dir3_sfe_put_ino can be static
xfs: introduce object readahead to log recovery
xfs: Simplify xfs_ail_min() with list_first_entry_or_null()
xfs: Register hotcpu notifier after initialization
xfs: add xfs sb v4 support for dirent filetype field
xfs: Add write support for dirent filetype field
xfs: Add read-only support for dirent filetype field
...
|
|
Pull mtd updates from David Woodhouse:
- factor out common code from MTD tests
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc
* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
mtd: ofpart: use for_each_child_of_node() macro
mtd: mtdswap: replace strict_strtoul() with kstrtoul()
mtd cs553x_nand: use kzalloc() instead of memset
mtd: atmel_nand: fix error return code in atmel_nand_probe()
mtd: bcm47xxsflash: writing support
mtd: bcm47xxsflash: implement erasing support
mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
mtd: remove alauda driver
mtd: nand: mxc_nand: mark 'const' properly
mtd: maps: cfi_flagadm: add missing __iomem annotation
mtd: spear_smi: add missing __iomem annotation
mtd: r852: Staticize local symbols
mtd: nandsim: Staticize local symbols
mtd: impa7: add missing __iomem annotation
mtd: sm_ftl: Staticize local symbols
mtd: m25p80: add support for mr25h10
mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
mtd: m25p80: Pass flags through CAT25_INFO macro
...
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA mapping update from Marek Szyprowski:
"This contains an addition of Device Tree support for reserved memory
regions (Contiguous Memory Allocator is one of the drivers for it) and
changes required by the KVM extensions for PowerPC architectue"
* 'for-v3.12' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: init: add support for reserved memory defined by device tree
drivers: of: add initialization code for dma reserved memory
drivers: of: add function to scan fdt nodes given by path
drivers: dma-contiguous: clean source code and prepare for device tree
|
|
Pull VFIO update from Alex Williamson:
"VFIO updates include safer default file flags for VFIO device fds, an
external user interface exported to allow other modules to hold
references to VFIO groups, a fix to test for extended config space on
PCIe and PCI-x, and new hot reset interfaces for PCI devices which
allows the user to do PCI bus/slot resets when all of the devices
affected by the reset are owned by the user.
For this last feature, the PCI bus reset interface, I depend on
changes already merged from Bjorn's PCI pull request. I therefore
merged my tree up to commit cb3e433, which I think was the correct
action, but as Stephen Rothwell noted, I failed to provide a commit
message indicating why the merge was required. Sorry for that.
Thanks, Alex"
* tag 'vfio-v3.12-rc0' of git://github.com/awilliam/linux-vfio:
vfio: fix documentation
vfio-pci: PCI hot reset interface
vfio-pci: Test for extended config space
vfio-pci: Use fdget() rather than eventfd_fget()
vfio: Add O_CLOEXEC flag to vfio device fd
vfio: use get_unused_fd_flags(0) instead of get_unused_fd()
vfio: add external user support
|
|
Pull NFS client updates from Trond Myklebust:
"Highlights include:
- Fix NFSv4 recovery so that it doesn't recover lost locks in cases
such as lease loss due to a network partition, where doing so may
result in data corruption. Add a kernel parameter to control
choice of legacy behaviour or not.
- Performance improvements when 2 processes are writing to the same
file.
- Flush data to disk when an RPCSEC_GSS session timeout is imminent.
- Implement NFSv4.1 SP4_MACH_CRED state protection to prevent other
NFS clients from being able to manipulate our lease and file
locking state.
- Allow sharing of RPCSEC_GSS caches between different rpc clients.
- Fix the broken NFSv4 security auto-negotiation between client and
server.
- Fix rmdir() to wait for outstanding sillyrename unlinks to complete
- Add a tracepoint framework for debugging NFSv4 state recovery
issues.
- Add tracing to the generic NFS layer.
- Add tracing for the SUNRPC socket connection state.
- Clean up the rpc_pipefs mount/umount event management.
- Merge more patches from Chuck in preparation for NFSv4 migration
support"
* tag 'nfs-for-3.12-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (107 commits)
NFSv4: use mach cred for SECINFO_NO_NAME w/ integrity
NFS: nfs_compare_super shouldn't check the auth flavour unless 'sec=' was set
NFSv4: Allow security autonegotiation for submounts
NFSv4: Disallow security negotiation for lookups when 'sec=' is specified
NFSv4: Fix security auto-negotiation
NFS: Clean up nfs_parse_security_flavors()
NFS: Clean up the auth flavour array mess
NFSv4.1 Use MDS auth flavor for data server connection
NFS: Don't check lock owner compatability unless file is locked (part 2)
NFS: Don't check lock owner compatibility in writes unless file is locked
nfs4: Map NFS4ERR_WRONG_CRED to EPERM
nfs4.1: Add SP4_MACH_CRED write and commit support
nfs4.1: Add SP4_MACH_CRED stateid support
nfs4.1: Add SP4_MACH_CRED secinfo support
nfs4.1: Add SP4_MACH_CRED cleanup support
nfs4.1: Add state protection handler
nfs4.1: Minimal SP4_MACH_CRED implementation
SUNRPC: Replace pointer values with task->tk_pid and rpc_clnt->cl_clid
SUNRPC: Add an identifier for struct rpc_clnt
SUNRPC: Ensure rpc_task->tk_pid is available for tracepoints
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph updates from Sage Weil:
"This includes both the first pile of Ceph patches (which I sent to
torvalds@vger, sigh) and a few new patches that add support for
fscache for Ceph. That includes a few fscache core fixes that David
Howells asked go through the Ceph tree. (Thanks go to Milosz Tanski
for putting this feature together)
This first batch of patches (included here) had (has) several
important RBD bug fixes, hole punch support, several different
cleanups in the page cache interactions, improvements in the truncate
code (new truncate mutex to avoid shenanigans with i_mutex), and a
series of fixes in the synchronous striping read/write code.
On top of that is a random collection of small fixes all across the
tree (error code checks and error path cleanup, obsolete wq flags,
etc)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (43 commits)
ceph: use d_invalidate() to invalidate aliases
ceph: remove ceph_lookup_inode()
ceph: trivial buildbot warnings fix
ceph: Do not do invalidate if the filesystem is mounted nofsc
ceph: page still marked private_2
ceph: ceph_readpage_to_fscache didn't check if marked
ceph: clean PgPrivate2 on returning from readpages
ceph: use fscache as a local presisent cache
fscache: Netfs function for cleanup post readpages
FS-Cache: Fix heading in documentation
CacheFiles: Implement interface to check cache consistency
FS-Cache: Add interface to check consistency of a cached object
rbd: fix null dereference in dout
rbd: fix buffer size for writes to images with snapshots
libceph: use pg_num_mask instead of pgp_num_mask for pg.seed calc
rbd: fix I/O error propagation for reads
ceph: use vfs __set_page_dirty_nobuffers interface instead of doing it inside filesystem
ceph: allow sync_read/write return partial successed size of read/write.
ceph: fix bugs about handling short-read for sync read mode.
ceph: remove useless variable revoked_rdcache
...
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and move the extern from linux/namei.h to fs/internal.h,
along with that of vfs_path_lookup().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This is me being a bit OCD after all the dentry optimization work this
merge window: profiles end up showing 'dput()' as a rather expensive
operation, and there were two unrelated bad reasons for that.
The first reason was reading d_lockref.count for debugging purposes,
which touches the lockref cacheline (for reads) before really need to.
More importantly, the debugging test in question is _wrong_, and has
hidden bugs. It's true that we can only sleep when the count goes down
to zero, but the test as-is hides the much more subtle bug that happens
if we race with somebody else deleting the file.
Anyway we _will_ touch that cacheline, but let's do it for a write and
in the right routine (ie in "lockref_put_or_lock()") which annotates the
costs better. So remove the misleading debug code.
The other was an unnecessary access to the cacheline that contains the
d_lru list, just to check whether we already were on the LRU list or
not. This is exactly what we have d_flags for, so that we can avoid
touching extra cache lines for the common case. So just add another bit
for "is this dentry on the LRU".
Finally, mark the tests properly likely/unlikely, so that the common
fast-paths are dense in the instruction stream.
This makes the profiles look much saner.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull NVM Express driver update from Matthew Wilcox.
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Merge issue on character device bring-up
NVMe: Handle ioremap failure
NVMe: Add pci suspend/resume driver callbacks
NVMe: Use normal shutdown
NVMe: Separate controller init from disk discovery
NVMe: Separate queue alloc/free from create/delete
NVMe: Group pci related actions in functions
NVMe: Disk stats for read/write commands only
NVMe: Bring up cdev on set feature failure
NVMe: Fix checkpatch issues
NVMe: Namespace IDs are unsigned
NVMe: Update nvme_id_power_state with latest spec
NVMe: Split header file into user-visible and kernel-visible pieces
NVMe: Call nvme_process_cq from submission path
NVMe: Remove "process_cq did something" message
NVMe: Return correct value from interrupt handler
NVMe: Disk IO statistics
NVMe: Restructure MSI / MSI-X setup
NVMe: Use kzalloc instead of kmalloc+memset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD (multi-function device) updates from Samuel Ortiz:
"For the 3.12 merge window we have one new driver for the DA9063 PMIC
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving
support, better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register
tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes"
* tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (81 commits)
mfd: ucb1x00-core: Rewrite ucb1x00_add_dev()
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for event name
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for sysfs
mfd: timberdale: Use module_pci_driver
mfd: timberdale: Remove redundant break
mfd: timberdale: Staticize local variables
mfd: ab8500-debugfs: Staticize local variables
mfd: db8500-prcmu: Staticize clk_mgt
mfd: db8500-prcmu: Use ANSI function declaration
mfd: omap-usb-host: Staticize usbhs_driver_name
mfd: 88pm805: Fix potential NULL pdata dereference
mfd: 88pm800: Fix potential NULL pdata dereference
mfd: twl6040: Use regmap for register cache
mfd: davinci_voicecodec: Provide a regmap for register I/O
mfd: davinci_voicecodec: Remove unused read and write functions
mmc: memstick: rtsx: Modify copyright comments
mmc: rtsx: Clear SD_CLK toggle enable bit if switching voltage fail
mfd: mmc: rtsx: Change default tx phase
mfd: pcf50633-adc: Use devm_*() functions
mfd: rtsx: Copyright modifications
...
|
|
kernel/cgroup.c is the only place in the tree that relies on eventfd.h
pulling file.h; move that include there. Switch from eventfd_fget()/fput()
to fdget()/fdput(), while we are at it - eventfd_ctx_fileget() will fail
on non-eventfd descriptors just fine, no need to do that check twice...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The only actual current lockref user (dcache) uses zero reference counts
even for perfectly live dentries, because it's a cache: there may not be
any users, but that doesn't mean that we want to throw away the dentry.
At the same time, the dentry cache does have a notion of a truly "dead"
dentry that we must not even increment the reference count of, because
we have pruned it and it is not valid.
Currently that distinction is not visible in the lockref itself, and the
dentry cache validation uses "lockref_get_or_lock()" to either get a new
reference to a dentry that already had existing references (and thus
cannot be dead), or get the dentry lock so that we can then verify the
dentry and increment the reference count under the lock if that
verification was successful.
That's all somewhat complicated.
This adds the concept of being "dead" to the lockref itself, by simply
using a count that is negative. This allows a usage scenario where we
can increment the refcount of a dentry without having to validate it,
and pushing the special "we killed it" case into the lockref code.
The dentry code itself doesn't actually use this yet, and it's probably
too late in the merge window to do that code (the dentry_kill() code
with its "should I decrement the count" logic really is pretty complex
code), but let's introduce the concept at the lockref level now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile 2 (of many) from Al Viro:
"Mostly Miklos' series this time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify dcache.c inlined helpers where possible
fuse: drop dentry on failed revalidate
fuse: clean up return in fuse_dentry_revalidate()
fuse: use d_materialise_unique()
sysfs: use check_submounts_and_drop()
nfs: use check_submounts_and_drop()
gfs2: use check_submounts_and_drop()
afs: use check_submounts_and_drop()
vfs: check unlinked ancestors before mount
vfs: check submounts and drop atomically
vfs: add d_walk()
vfs: restructure d_genocide()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace changes from Eric Biederman:
"This is an assorted mishmash of small cleanups, enhancements and bug
fixes.
The major theme is user namespace mount restrictions. nsown_capable
is killed as it encourages not thinking about details that need to be
considered. A very hard to hit pid namespace exiting bug was finally
tracked and fixed. A couple of cleanups to the basic namespace
infrastructure.
Finally there is an enhancement that makes per user namespace
capabilities usable as capabilities, and an enhancement that allows
the per userns root to nice other processes in the user namespace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Kill nsown_capable it makes the wrong thing easy
capabilities: allow nice if we are privileged
pidns: Don't have unshare(CLONE_NEWPID) imply CLONE_THREAD
userns: Allow PR_CAPBSET_DROP in a user namespace.
namespaces: Simplify copy_namespaces so it is clear what is going on.
pidns: Fix hang in zap_pid_ns_processes by sending a potentially extra wakeup
sysfs: Restrict mounting sysfs
userns: Better restrictions on when proc and sysfs can be mounted
vfs: Don't copy mount bind mounts of /proc/<pid>/ns/mnt between namespaces
kernel/nsproxy.c: Improving a snippet of code.
proc: Restrict mounting the proc filesystem
vfs: Lock in place mounts from more privileged users
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Nothing major for this kernel, just maintenance updates"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
apparmor: add the ability to report a sha1 hash of loaded policy
apparmor: export set of capabilities supported by the apparmor module
apparmor: add the profile introspection file to interface
apparmor: add an optional profile attachment string for profiles
apparmor: add interface files for profiles and namespaces
apparmor: allow setting any profile into the unconfined state
apparmor: make free_profile available outside of policy.c
apparmor: rework namespace free path
apparmor: update how unconfined is handled
apparmor: change how profile replacement update is done
apparmor: convert profile lists to RCU based locking
apparmor: provide base for multiple profiles to be replaced at once
apparmor: add a features/policy dir to interface
apparmor: enable users to query whether apparmor is enabled
apparmor: remove minimum size check for vmalloc()
Smack: parse multiple rules per write to load2, up to PAGE_SIZE-1 bytes
Smack: network label match fix
security: smack: add a hash table to quicken smk_find_entry()
security: smack: fix memleak in smk_write_rules_list()
xattr: Constify ->name member of "struct xattr".
...
|
|
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
- Handle unaligned lengths in omap-aes.
- Added SHA384/SHA512 to omap-sham.
- Added OMAP5/AM43XX SHAM support.
- Added OMAP4 TRNG support.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
hwrng: via - Add MODULE_DEVICE_TABLE
crypto: fcrypt - Fix bitoperation for compilation with clang
crypto: nx - fix SHA-2 for chunks bigger than block size
crypto: nx - fix GCM for zero length messages
crypto: nx - fix XCBC for zero length messages
crypto: nx - fix limits to sg lists for AES-CCM
crypto: nx - fix limits to sg lists for AES-XCBC
crypto: nx - fix limits to sg lists for AES-GCM
crypto: nx - fix limits to sg lists for AES-CTR
crypto: nx - fix limits to sg lists for AES-CBC
crypto: nx - fix limits to sg lists for AES-ECB
crypto: nx - add offset to nx_build_sg_lists()
padata - Register hotcpu notifier after initialization
padata - share code between CPU_ONLINE and CPU_DOWN_FAILED, same to CPU_DOWN_PREPARE and CPU_UP_CANCELED
hwrng: omap - reorder OMAP TRNG driver code
crypto: omap-sham - correct dma burst size
crypto: omap-sham - Enable Polling mode if DMA fails
crypto: tegra-aes - bitwise vs logical and
crypto: sahara - checking the wrong variable
...
|
|
Pull networking fixes from David Miller:
"A quick set of fixes, some to deal with fallout from yesterday's
net-next merge.
1) Fix compilation of bnx2x driver with CONFIG_BNX2X_SRIOV disabled,
from Dmitry Kravkov.
2) Fix a bnx2x regression caused by one of Dave Jones's mistaken
braces changes, from Eilon Greenstein.
3) Add some protective filtering in the netlink tap code, from Daniel
Borkmann.
4) Fix TCP congestion window growth regression after timeouts, from
Yuchung Cheng.
5) Correctly adjust TCP's rcv_ssthresh for out of order packets, from
Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: properly increase rcv_ssthresh for ofo packets
net: add documentation for BQL helpers
mlx5: remove unused MLX5_DEBUG param in Kconfig
bnx2x: Restore a call to config_init
bnx2x: fix broken compilation with CONFIG_BNX2X_SRIOV is not set
tcp: fix no cwnd growth after timeout
net: netlink: filter particular protocols from analyzers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.12 series:
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block. This is
found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on some x86
boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the modernized pin
control driver to provide GPIO for the modern platforms instead.
- The usual bunch of non-critical fixes and cleanups"
* tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (36 commits)
gpio: return -ENOTSUPP if debounce cannot be set
gpio: improve error path in gpiolib
gpio: add GPIO support for F71882FG and F71889F
of: add vendor prefix for Microchip Technology Inc
gpio: mcp23s08: rename the device tree property
gpio: samsung: Drop support for Exynos SoCs
gpio: pcf857x: Remove pdata argument to pcf857x_irq_domain_init()
gpio: pcf857x: Sort headers alphabetically
gpio: max7301: Reverting "Do not force SPI speed when using OF Platform"
gpio: Fix bit masking in Kontron PLD GPIO driver
gpio: pca953x: fix gpio input on gpio offsets >= 8
drivers/gpio: simplify use of devm_ioremap_resource
drivers/gpio/gpio-omap.c: convert comma to semicolon
gpio-lynxpoint: Fix warning about unbalanced pm_runtime_enable
gpio: Fix platform driver name in Kontron PLD GPIO driver
gpio: adnp: Fix segfault if request_threaded_irq fails
gpio: msm: Staticize local variable 'msm_gpio'
gpio: gpiolib-of.c: make error message more meaningful by adding the node name and index
gpio: use dev_get_platdata()
gpio/mxc: add chained_irq_enter/exit() to mx2_gpio_irq_handler
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A new driver for slidebar on Ideapad laptops and a bunch of assorted
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: add SYN_MAX and SYN_CNT constants
Input: max11801_ts - convert to devm
Input: egalax-ts - fix typo and improve text
Input: MAINTAINERS - change maintainer for cyttsp driver
Input: cyttsp4 - kill 'defined but not used' compiler warnings
Input: add driver for slidebar on Lenovo IdeaPad laptops
Input: omap-keypad - set up irq type from DT
Input: omap-keypad - enable wakeup capability for keypad.
Input: omap-keypad - clear interrupts on open
Input: omap-keypad - convert to threaded IRQ
Input: omap-keypad - use bitfiled instead of hardcoded values
Input: cyttsp4 - remove useless NULL test from cyttsp4_watchdog_timer()
Input: wacom - fix error return code in wacom_probe()
Input: as5011 - fix error return code in as5011_probe()
Input: keyboard, serio - simplify use of devm_ioremap_resource
Input: tegra-kbc - simplify use of devm_ioremap_resource
Input: htcpen - fix incorrect placement of __initdata
Input: qt1070 - add power management ops
Input: wistron_btns - add MODULE_DEVICE_TABLE
Input: wistron_btns - mark the Medion MD96500 keymap as tested
...
|
|
This reverts commits 61e00655e9cb, 73f8645db191 and 8e22ecb603c8:
"Input: introduce BTN/ABS bits for drums and guitars"
"HID: wiimote: add support for Guitar-Hero drums"
"HID: wiimote: add support for Guitar-Hero guitars"
The extra new ABS_xx values resulted in ABS_MAX no longer being a
power-of-two, which broke the comparison logic. It also caused the
ioctl numbers to overflow into the next byte, causing problems for that.
We'll try again for 3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge first round of changes for 3.12 merge window.
|
|
transform framework"
This patch reinstates commits
67822649d7305caf3dd50ed46c27b99c94eff996
39761214eefc6b070f29402aa1165f24d789b3f7
0b95a7f85718adcbba36407ef88bba0a7379ed03
31d939625a9a20b1badd2d4e6bf6fd39fa523405
2d31e518a42828df7877bca23a958627d60408bc
Now that module softdeps are in the kernel we can use that to resolve
the boot issue which cause the revert.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Merge upstream tree in order to reinstate crct10dif.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
|
