| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Using a bare block cipher in non-crypto code is almost always a bad idea,
not only for security reasons (and we've seen some examples of this in
the kernel in the past), but also for performance reasons.
In the TCP fastopen case, we call into the bare AES block cipher one or
two times (depending on whether the connection is IPv4 or IPv6). On most
systems, this results in a call chain such as
crypto_cipher_encrypt_one(ctx, dst, src)
crypto_cipher_crt(tfm)->cit_encrypt_one(crypto_cipher_tfm(tfm), ...);
aesni_encrypt
kernel_fpu_begin();
aesni_enc(ctx, dst, src); // asm routine
kernel_fpu_end();
It is highly unlikely that the use of special AES instructions has a
benefit in this case, especially since we are doing the above twice
for IPv6 connections, instead of using a transform which can process
the entire input in one go.
We could switch to the cbcmac(aes) shash, which would at least get
rid of the duplicated overhead in *some* cases (i.e., today, only
arm64 has an accelerated implementation of cbcmac(aes), while x86 will
end up using the generic cbcmac template wrapping the AES-NI cipher,
which basically ends up doing exactly the above). However, in the given
context, it makes more sense to use a light-weight MAC algorithm that
is more suitable for the purpose at hand, such as SipHash.
Since the output size of SipHash already matches our chosen value for
TCP_FASTOPEN_COOKIE_SIZE, and given that it accepts arbitrary input
sizes, this greatly simplifies the code as well.
NOTE: Server farms backing a single server IP for load balancing purposes
and sharing a single fastopen key will be adversely affected by
this change unless all systems in the pool receive their kernel
upgrades at the same time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_reset hook is not set anywhere. Drop it to make
stmmac_mdio_reset() smaller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only OF platforms use the reset delays and these delays are only read in
stmmac_mdio_reset(). Move them from struct stmmac_mdio_bus_data to a
stack variable inside stmmac_mdio_reset() because that's the only usage
of these delays.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No platform uses the "reset_gpio" field from stmmac_mdio_bus_data
anymore. Drop it so we don't get any new consumers either.
Plain GPIO numbers are being deprecated in favor of GPIO descriptors. If
needed any new non-OF platform can add a GPIO descriptor lookup table.
devm_gpiod_get_optional() will find the GPIO in that case.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This config option makes only couple of lines optional.
Two small helpers and an int in couple of cls structs.
Remove the config option and always compile this in.
This saves the user from unexpected surprises when he adds
a filter with ingress device match which is silently ignored
in case the config option is not set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because of PHYLINK conversion we stopped parsing the phy-handle property
from DT. Unfortunatelly, some wrapper drivers still rely on this phy
node to configure the PHY.
Let's restore the parsing of PHY handle while these wrapper drivers are
not fully converted to PHYLINK.
Fixes: 74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A port may trigger operations on its dedicated CPU port, so using
cpu_dp as const will raise warnings. Make cpu_dp non const.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we want to set a EDT time for the skb we want to send
via ip_send_unicast_reply(), we have to pass a new parameter
and initialize ipc.sockc.transmit_time with it.
This fixes the EDT time for ACK/RST packets sent on behalf of
a TIME_WAIT socket.
Fixes: a842fe1425cb ("tcp: add optional per socket transmit delay")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-06-13
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This interface is currently only defined if CONFIG_JUMP_LABEL. Make it
available also when jump labels are off.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.
The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cfg80211_remain_on_channel_expired is used to notify userspace when
the remain on channel duration expired by sending an event. There is
no such equivalent to CMD_FRAME, where if offchannel and a duration
is provided, the card will go offchannel for that duration. Currently
there is no way for userspace to tell when that duration expired
apart from setting an independent timeout. This timeout is quite
erroneous as the kernel may not immediately send out the frame
because of scheduling or work queue delays. In testing, it was found
this timeout had to be quite large to accomidate any potential delays.
A better solution is to have the kernel send an event when this
duration has expired. There is already NL80211_CMD_FRAME_WAIT_CANCEL
which can be used to cancel a NL80211_CMD_FRAME offchannel. Using this
command matches perfectly to how NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL
works, where its both used to cancel and notify if the duration has
expired.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the "OBSS Narrow Bandwidth RU In OFDMA Tolerance Support" flag
definition to the definitions of the flags covered by the Extended
Capability IE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a function that iterates over the BSS entries associated with a
given wiphy and calls a callback for each iterated BSS. This can be
used by drivers in various ways, e.g., to evaluate some property for
all the BSSs in the medium.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Turn TWT for STA interfaces when they associate and/or receive a
beacon where the twt_responder bit has changed.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This function is similar to ieee80211_get_he_sta_cap() but allows passing
the iftype. Also make ieee80211_get_he_sta_cap() use the new helper
rather than duplicating the code.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Let drivers advertise support for station-mode SAE authentication
offload with a new NL80211_EXT_FEATURE_SAE_OFFLOAD flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add definition of WPA version 3 for SAE authentication.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
IEEE 802.11 - 2016 forbids mixing MPDUs with different keyIDs in one
A-MPDU. Drivers supporting A-MPDUs and Extended Key ID must actively
enforce that requirement due to the available two unicast keyIDs.
Allow driver to signal mac80211 that they will not check the keyID in
MPDUs when aggregating them and that they expect mac80211 to stop Tx
aggregation when rekeying a connection using Extended Key ID.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Publish scaled_ppm_to_ppb to allow drivers to use it.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report devlink health on FW fatal issues via fw_fatal_reporter. The
driver recover flow for FW fatal error is now being handled by the
devlink health.
Having the recovery controlled by devlink health, the user has the
ability to cancel the auto-recovery for debug session and run it
manually.
Call mlx5_enter_error_state() before calling devlink_health_report() to
ensure entering device error state even if auto-recovery is off.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Create mlx5_devlink_health_reporter for fw fatal reporter.
The fw fatal reporter is added in addition to the fw reporter and
implements the recover callback.
The point of having two reporters for FW issues, is that we
don't want to run FW recover on any issue, but only fatal ones.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use devlink_health_report() to report any symptom of FW issue as FW
counter miss or new health syndrome.
The FW issues detected in mlx5 during poll_health which is called in
timer atomic context and so health work queue is used to schedule the
reports.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Create mlx5_devlink_health_reporter for FW reporter. The FW reporter
implements devlink_health_reporter diagnose callback.
The fw reporter diagnose command can be triggered any time by the user
to check current fw status.
In healthy status, it will return clear syndrome. Otherwise it will
return the syndrome and description of the error type.
Command example and output on healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 0
Command example and output on non healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 8 Description: unrecoverable hardware error
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If a FW assert is considered fatal, indicated by a new bit in the health
buffer, reset the FW. After the reset go through the normal recovery
flow. Only one PF needs to issue the reset, so an attempt is made to
prevent the 2nd function from also issuing the reset.
It's not an error if that happens, it just slows recovery.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
New mlx5 adapters allow the driver to reset the FW in the event of an
error, this action called "SW Reset". When an SW reset is issued on any
PF all PFs enter reset state which is a recoverable condition. The
existing recovery flow was designed to allow the recovery of a VF after
a PF driver reload. This patch adds the sw reset to the NIC states
as a preparation for sw reset handling.
When a software reset is issued the following occurs:
1. The NIC interface mode is set to 7 while the reset is in progress.
2. Once the reset completes the NIC interface mode is set to 1.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Crdump allows the driver to retrieve a dump of the FW PCI crspace.
This is useful in case of catastrophic issues which may require FW
reset. The crspace dump can be used for later debug.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The Vendor Specific Capability (VSC) is used to activate a gateway
interfacing with the device. The gateway is used to read or write
device configurations, which are organized in different domains (spaces).
A configuration access may result in multiple actions, reads, writes.
Example usages are accessing the Crspace domain to read the crspace or
locking a device semaphore using the Semaphore domain.
The configuration access use pci_cfg_access to prevent parallel access to
the VSC space by the driver and userspace calls.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Adding delays to TCP flows is crucial for studying behavior
of TCP stacks, including congestion control modules.
Linux offers netem module, but it has unpractical constraints :
- Need root access to change qdisc
- Hard to setup on egress if combined with non trivial qdisc like FQ
- Single delay for all flows.
EDT (Earliest Departure Time) adoption in TCP stack allows us
to enable a per socket delay at a very small cost.
Networking tools can now establish thousands of flows, each of them
with a different delay, simulating real world conditions.
This requires FQ packet scheduler or a EDT-enabled NIC.
This patchs adds TCP_TX_DELAY socket option, to set a delay in
usec units.
unsigned int tx_delay = 10000; /* 10 msec */
setsockopt(fd, SOL_TCP, TCP_TX_DELAY, &tx_delay, sizeof(tx_delay));
Note that FQ packet scheduler limits might need some tweaking :
man tc-fq
PARAMETERS
limit
Hard limit on the real queue size. When this limit is
reached, new packets are dropped. If the value is lowered,
packets are dropped so that the new limit is met. Default
is 10000 packets.
flow_limit
Hard limit on the maximum number of packets queued per
flow. Default value is 100.
Use of TCP_TX_DELAY option will increase number of skbs in FQ qdisc,
so packets would be dropped if any of the previous limit is hit.
Use of a jump label makes this support runtime-free, for hosts
never using the option.
Also note that TSQ (TCP Small Queues) limits are slightly changed
with this patch : we need to account that skbs artificially delayed
wont stop us providind more skbs to feed the pipe (netem uses
skb_orphan_partial() for this purpose, but FQ can not use this trick)
Because of that, using big delays might very well trigger
old bugs in TSO auto defer logic and/or sndbuf limited detection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently only RX direction is ever resynced, however, TX may
also get out of sequence if packets get dropped on the way to
the driver. Rename the resync callback and add a direction
parameter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
handle_device_resync() doesn't describe the function very well.
The function checks if resync should be issued upon parsing of
a new record.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload code casts record number to a u64. The buffer
should be aligned to 8 bytes, but its actually a __be64, and
the rest of the TLS code treats it as big int. Make the
offload callbacks take a byte array, drivers can make the
choice to do the ugly cast if they want to.
Prepare for copying the record number onto the stack by
defining a constant for max size of the byte array.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib6_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update ip6_route_del to check metric and protocol before nexthop
specs. If fc_nh_id is set, then it must match the id in the route
entry. Since IPv6 allows delete of a cached entry (an exception),
add ip6_del_cached_rt_nh to cycle through all of the fib6_nh in
a fib entry if it is using a nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update fib_nh_match to check ids on a route delete.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 has traditionally had a single fib6_nh per fib6_info. With
nexthops we can have multiple fib6_nh associated with a fib6_info.
Add a nexthop helper to invoke a callback for each fib6_nh in a
'struct nexthop'. If the callback returns non-0, the loop is
stopped and the return value passed to the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case autoflowlabel is in action, skb_get_hash_flowi6()
derives a non zero skb->hash to the flowlabel.
If skb->hash is zero, a flow dissection is performed.
Since all TCP skbs sent from ESTABLISH state inherit their
skb->hash from sk->sk_txhash, we better keep a copy
of sk->sk_txhash into the TIME_WAIT socket.
After this patch, ACK or RST packets sent on behalf of
a TIME_WAIT socket have the flowlabel that was previously
used by the flow.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on review, `lock' is only acquired in hwbm_pool_add() which is
invoked via ->probe(), ->resume() and ->ndo_change_mtu(). Based on this
the lock can become a mutex and there is no need to disable interrupts
during the procedure.
Now that the lock is a mutex, hwbm_pool_add() no longer invokes
hwbm_pool_refill() in an atomic context so we can pass GFP_KERNEL to
hwbm_pool_refill() and remove the `gfp' argument from hwbm_pool_add().
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nhg->nh_entries[] array is allocated in nexthop_grp_alloc() and it
has nhg->num_nh elements so this check should be >= instead of >.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where possible, we generally want both the bond master and the relevant slave
information in message output. Standardize the format using new slave_*
printk macros.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Meta frame reception relies on the hardware keeping its promise that it
will send no other traffic towards the CPU port between a link-local
frame and a meta frame. Otherwise there is no other way to associate
the meta frame with the link-local frame it's holding a timestamp of.
The receive function is made stateful, and buffers a timestampable frame
until its meta frame arrives, then merges the two, drops the meta and
releases the link-local frame up the stack.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be used to keep state for RX timestamping. It is global
because the switch serializes timestampable and meta frames when
trapping them towards the CPU port (lower port indices have higher
priority) and therefore having one state machine per port would create
unnecessary complications.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Meta frames are sent on the CPU port by the switch if RX timestamping is
enabled. They contain a partial timestamp of the previous frame.
They are Ethernet frames with the Ethernet header constructed out of:
- SJA1105_META_DMAC
- SJA1105_META_SMAC
- ETH_P_SJA1105_META
The Ethernet payload will be decoded in a follow-up patch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On TX, timestamping is performed synchronously from the
port_deferred_xmit worker thread.
In management routes, the switch is requested to take egress timestamps
(again partial), which are reconstructed and appended to a clone of the
skb that was just sent. The cloning is done by DSA and we retrieve the
pointer from the structure that DSA keeps in skb->cb.
Then these clones are enqueued to the socket's error queue for
application-level processing.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes the existing implementation from tag_sja1105, which was
partially incorrect (it was not changing the MAC header offset, thereby
leaving it to point 4 bytes earlier than it should have).
This overwrites the VLAN tag by moving the Ethernet source and
destination MACs 4 bytes to the right. Then skb->data (assumed to be
pointing immediately after the EtherType) is temporarily pushed to the
beginning of the new Ethernet header, the new Ethernet header offset and
length are recorded, then skb->data is moved back to where it was.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
