Age | Commit message (Collapse) | Author | Files | Lines |
|
Pull MTD fixes from David Woodhouse:
"This fixes a couple of problems. Firstly, some people are actually
still using old small-page flash and we broke it by removing the ready
check.
Secondly. fix the handling of partitions on Broadcom 47xx devices.
Recent changes had made it misdetect the location of the NVRAM and
scribble over the bootloader when it tried to update the variables
there. With predictably sad results."
* tag 'for-linus-20130318' of git://git.infradead.org/linux-mtd:
mtd: nand: reintroduce NAND_NO_READRDY as NAND_NEED_READRDY
mtd: bcm47xxpart: look for NVRAM at the end of device
Revert "mtd: bcm47xxpart: improve probing of nvram partition"
|
|
Pull ARM SoC bug fixes from Arnd Bergmann:
"Things are calming down for arm-soc as well. This set of bug fixes is
dominated in size by the at91 platform bug fixes. Some of them were
meant to go through the framebuffer tree during the merge window, but
since the framebuffer maintainer could not be reached, I offered to
take them here. The other notable at91 change is the addition of
pinctrl definitions to fix the NAND controller.
The rest are mostly simple regression fixes:
- Our removal of VIRT_TO_BUS conflicted with Stephen Rothwell's
renaming of the Kconfig symbol. You will get a trivial merge
conflict here, we still want to remove it.
- missing bits for clocks on imx and s5pv210
- missing header inclusions in mmp and shmobile
- typos in s5pv210 camera and vt8500 clock support code
and three trivial fixes for pre-3.8 bugs:
- an old bogus build warning in the joystick driver
- a misleading Kconfig description
- a NULL pointer check on davinci"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: fix CONFIG_VIRT_TO_BUS handling
ARM: i.MX35: enable MAX clock
ARM: Scorpion is a v7 architecture, not v6
ARM: mmp: add platform_device head file in gplugd
input/joystick: use get_cycles on ARM
[media] s5p-fimc: fix s5pv210 build
clk: vt8500: Fix "fix device clock divisor calculations"
ARM: i.MX25: Fix DT compilation
ARM: at91: fix infinite loop in at91_irq_suspend/resume
ARM: at91: add gpio suspend/resume support when using pinctrl
ARM: at91: fix LCD-wiring mode
atmel_lcdfb: fix 16-bpp modes on older SOCs
ARM: at91: dt: at91sam9x5: complete NAND pinctrl
ARM: at91: dt: at91sam9x5: correct NAND pins comments
ARM: davinci: edma: fix dmaengine induced null pointer dereference on da830
ARM: shmobile: marzen: Include mmc/host.h
ARM: EXYNOS: Add #dma-cells for generic dma binding support for PL330
ARM: S5PV210: Fix PL330 DMA controller clkdev entries
|
|
Commit 1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") introduces a link failure since
perf_restore_debug_store() is only defined for CONFIG_CPU_SUP_INTEL:
arch/x86/power/built-in.o: In function `restore_processor_state':
(.text+0x45c): undefined reference to `perf_restore_debug_store'
Fix it by defining the dummy function appropriately.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull OpenRISC bug fixes from Jonas Bonn:
- The GPIO descriptor work has exposed how broken the non-GPIOLIB bits
for OpenRISC were. We now require GPIOLIB as this is the preferred
way forward.
- The system.h split introduced a bug in llist.h for arches using
asm-generic/cmpxchg.h directly, which is currently only OpenRISC.
The patch here moves two defines from asm-generic/atomic.h to
asm-generic/cmpxchg.h to make things work as they should.
- The VIRT_TO_BUS selector was added for OpenRISC, but OpenRISC does
not have the virt_to_bus methods, so there's a patch to remove it
again.
* tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux:
openrisc: remove HAVE_VIRT_TO_BUS
asm-generic: move cmpxchg*_local defs to cmpxchg.h
openrisc: require gpiolib
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes
Pull MFD fixes from Samuel Ortiz:
"This is the first batch of MFD fixes for 3.9.
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when
built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the
hostconfig register.
- A couple of warning fixes for ab8500-gpadc and tps65912"
* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: twl4030-madc: Remove __exit_p annotation
mfd: ab8500: Kill "reg" property from binding
mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
mfd: wm831x: Don't forward declare enum wm831x_auxadc
mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
mfd: tps65912: Declare and use tps65912_irq_exit()
mfd: palmas: Provide irq flags through DT/platform data
mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
mfd: omap-usb-host: Actually update hostconfig
|
|
This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.
The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull fix for hlist_entry_safe() regression from Paul McKenney:
"This contains a single commit that fixes a regression in
hlist_entry_safe(). This macro references its argument twice, which
can cause NULL-pointer errors. This commit applies a gcc statement
expression, creating a temporary variable to avoid the double
reference. This has been posted to LKML at
https://lkml.org/lkml/2013/3/9/75.
Kudos to CAI Qian, whose testing uncovered this, to Eric Dumazet, who
spotted root cause, and to Li Zefan, who tested this commit."
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
list: Fix double fetch of pointer in hlist_entry_safe()
|
|
The current version of hlist_entry_safe() fetches the pointer twice,
once to test for NULL and the other to compute the offset back to the
enclosing structure. This is OK for normal lock-based use because in
that case, the pointer cannot change. However, when the pointer is
protected by RCU (as in "rcu_dereference(p)"), then the pointer can
change at any time. This use case can result in the following sequence
of events:
1. CPU 0 invokes hlist_entry_safe(), fetches the RCU-protected
pointer as sees that it is non-NULL.
2. CPU 1 invokes hlist_del_rcu(), deleting the entry that CPU 0
just fetched a pointer to. Because this is the last entry
in the list, the pointer fetched by CPU 0 is now NULL.
3. CPU 0 refetches the pointer, obtains NULL, and then gets a
NULL-pointer crash.
This commit therefore applies gcc's "({ })" statement expression to
create a temporary variable so that the specified pointer is fetched
only once, avoiding the above sequence of events. Please note that
it is the caller's responsibility to use rcu_dereference() as needed.
This allows RCU-protected uses to work correctly without imposing
any additional overhead on the non-RCU case.
Many thanks to Eric Dumazet for spotting root cause!
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Li Zefan <lizefan@huawei.com>
|
|
This partially reverts commit 1696e6bc2ae83734e64e206ac99766ea19e9a14e
("mtd: nand: kill NAND_NO_READRDY").
In that patch I overlooked a few things.
The original documentation for NAND_NO_READRDY included "True for all
large page devices, as they do not support autoincrement." I was
conflating "not support autoincrement" with the NAND_NO_AUTOINCR option,
which was in fact doing nothing. So, when I dropped NAND_NO_AUTOINCR, I
concluded that I then could harmlessly drop NAND_NO_READRDY. But of
course the fact the NAND_NO_AUTOINCR was doing nothing didn't mean
NAND_NO_READRDY was doing nothing...
So, NAND_NO_READRDY is re-introduced as NAND_NEED_READRDY and applied
only to those few remaining small-page NAND which needed it in the first
place.
Cc: stable@kernel.org [3.5+]
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Merge misc fixes from Andrew Morton:
- A bunch of fixes
- Finish off the idr API conversions before someone starts to use the
old interfaces again.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
idr: idr_alloc() shouldn't trigger lowmem warning when preloaded
UAPI: fix endianness conditionals in M32R's asm/stat.h
UAPI: fix endianness conditionals in linux/raid/md_p.h
UAPI: fix endianness conditionals in linux/acct.h
UAPI: fix endianness conditionals in linux/aio_abi.h
decompressors: fix typo "POWERPC"
mm/fremap.c: fix oops on error path
idr: deprecate idr_pre_get() and idr_get_new[_above]()
tidspbridge: convert to idr_alloc()
zcache: convert to idr_alloc()
mlx4: remove leftover idr_pre_get() call
workqueue: convert to idr_alloc()
nfsd: convert to idr_alloc()
nfsd: remove unused get_new_stid()
kernel/signal.c: use __ARCH_HAS_SA_RESTORER instead of SA_RESTORER
signal: always clear sa_restorer on execve
mm: remove_memory(): fix end_pfn setting
include/linux/res_counter.h needs errno.h
|
|
In the UAPI header files, __BIG_ENDIAN and __LITTLE_ENDIAN must be
compared against __BYTE_ORDER in preprocessor conditionals where these are
exposed to userspace (that is they're not inside __KERNEL__ conditionals).
However, in the main kernel the norm is to check for
"defined(__XXX_ENDIAN)" rather than comparing against __BYTE_ORDER and
this has incorrectly leaked into the userspace headers.
The definition of struct mdp_superblock_s in linux/raid/md_p.h is wrong in
this way. Note that userspace will likely interpret the ordering of the
fields incorrectly as the big-endian variant on a little-endian machines -
depending on header inclusion order.
[!!!] NOTE [!!!] This patch may adversely change the userspace API. It might
be better to fix the ordering of events_hi, events_lo, cp_events_hi and
cp_events_lo in struct mdp_superblock_s / typedef mdp_super_t.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the UAPI header files, __BIG_ENDIAN and __LITTLE_ENDIAN must be
compared against __BYTE_ORDER in preprocessor conditionals where these are
exposed to userspace (that is they're not inside __KERNEL__ conditionals).
However, in the main kernel the norm is to check for
"defined(__XXX_ENDIAN)" rather than comparing against __BYTE_ORDER and
this has incorrectly leaked into the userspace headers.
The definition of ACCT_BYTEORDER in linux/acct.h is wrong in this way.
Note that userspace will likely interpret this incorrectly as the
big-endian variant on little-endian machines - depending on header
inclusion order.
[!!!] NOTE [!!!] This patch may adversely change the userspace API. It might
be better to fix the value of ACCT_BYTEORDER.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the UAPI header files, __BIG_ENDIAN and __LITTLE_ENDIAN must be
compared against __BYTE_ORDER in preprocessor conditionals where these are
exposed to userspace (that is they're not inside __KERNEL__ conditionals).
However, in the main kernel the norm is to check for
"defined(__XXX_ENDIAN)" rather than comparing against __BYTE_ORDER and
this has incorrectly leaked into the userspace headers.
The definition of PADDED() in linux/aio_abi.h is wrong in this way. Note
that userspace will likely interpret this and thus the order of fields in
struct iocb incorrectly as the little-endian variant on big-endian
machines - depending on header inclusion order.
[!!!] NOTE [!!!] This patch may adversely change the userspace API. It might
be better to fix the ordering of aio_key and aio_reserved1 in struct iocb.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that all in-kernel users are converted to ues the new alloc
interface, mark the old interface deprecated. We should be able to
remove these in a few releases.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
alpha allmodconfig:
In file included from mm/memcontrol.c:28:
include/linux/res_counter.h: In function 'res_counter_set_limit':
include/linux/res_counter.h:203: error: 'EBUSY' undeclared (first use in this function)
include/linux/res_counter.h:203: error: (Each undeclared identifier is reported only once
include/linux/res_counter.h:203: error: for each function it appears in.)
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of tiny USB fixes and new USB device ids for your
3.9 tree.
The "largest" one here is a revert of a usb-storage patch that turned
out to be incorrect, breaking existing users, which is never a good
thing. Everything else is pretty simple and small"
* tag 'usb-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
USB: quatech2: only write to the tty if the port is open.
qcserial: bind to DM/DIAG port on Gobi 1K devices
USB: cdc-wdm: fix buffer overflow
usb: serial: Add Rigblaster Advantage to device table
qcaux: add Franklin U600
usb: musb: core: fix possible build error with randconfig
usb: cp210x new Vendor/Device IDs
usb: gadget: pxa25x: fix disconnect reporting
usb: dwc3: ep0: fix sparc64 build
usb: c67x00 RetryCnt value in c67x00 TD should be 3
usb: Correction to c67x00 TD data length mask
usb: Makefile: fix drivers/usb/phy/ Makefile entry
USB: added support for Cinterion's products AH6 and PLS8
usb: gadget: fix omap_udc build errors
USB: storage: fix Huawei mode switching regression
USB: storage: in-kernel modeswitching is deprecated
tools: usb: ffs-test: Fix build failure
USB: option: add Huawei E5331
usb: musb: omap2430: fix sparse warning
usb: musb: omap2430: fix omap_musb_mailbox glue check again
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9
We finally mute the annoying WARN_ON that lots of people are hitting
and it turns out isn't needed anymore. Also add a few new device ids
and a some other minor fixes."
* tag 'tty-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: fix typo "SERIAL_S3C2412"
serial: 8250: Keep 8250.<xxxx> module options functional after driver rename
tty: serial: fix typo "ARCH_S5P6450"
tty/8250_pnp: serial port detection regression since v3.7
serial: bcm63xx_uart: fix compilation after "TTY: switch tty_insert_flip_char"
serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller
Fix 4 port and add support for 8 port 'Unknown' PCI serial port cards
tty/serial: Add support for Altera serial port
tty: serial: vt8500: Unneccessary duplicated clock code removed
tty: serial: mpc5xxx: fix PSC clock name bug
TTY: disable debugging warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are some drivers/staging and drivers/iio fixes for 3.9 (the two
are still pretty intertwined, hence them coming both from my tree
still.) Nothing major, just a few things that have been reported by
users, all of these have been in linux-next for a while."
* tag 'staging-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: dt9812: use CR_CHAN() for channel number
staging/vt6656: Fix too large integer constant warning on 32-bit
staging: comedi: drivers: usbduxsigma.c: fix DMA buffers on stack
staging: imx/drm: request irq only after adding the crtc
staging: comedi: drivers: usbduxfast.c: fix for DMA buffers on stack
staging: comedi: drivers: usbdux.c: fix DMA buffers on stack
staging: vt6656: Fix oops on resume from suspend.
iio:common:st_sensors fixed all warning messages about uninitialized variables
iio: Fix build error seen if IIO_TRIGGER is defined but IIO_BUFFER is not
iio/imu: inv_mpu6050 depends on IIO_BUFFER
iio:ad5064: Initialize register cache correctly
iio:ad5064: Fix off by one in DAC value range check
iio:ad5064: Fix address of the second channel for ad5065/ad5045/ad5025
|
|
Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather than
BGR:565.
The above commit removes the RGB:555-wiring hack by
removing the no longer used ATMEL_LCDC_WIRING_RGB555 define.
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Fix regression introduced by commit 787f9fd23283 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.
Use SOC-type to determine the pixel layout.
Tested on at91sam9263 and at91sam9g45.
Cc: <stable@vger.kernel.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
asm/cmpxchg.h can be included on its own and needs to be self-consistent.
The definitions for the cmpxchg*_local macros, as such, need to be part
of this file.
This fixes a build issue on OpenRISC since the system.h smashing patch
96f951edb1f1bdbbc99b0cd458f9808bb83d58ae that introdued the direct inclusion
asm/cmpxchg.h into linux/llist.h.
CC: David Howells <dhowells@redhat.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix new kernel-doc warnings in idr:
Warning(include/linux/idr.h:113): No description found for parameter 'idr'
Warning(include/linux/idr.h:113): Excess function parameter 'idp' description in 'idr_find'
Warning(lib/idr.c:232): Excess function parameter 'id' description in 'sub_alloc'
Warning(lib/idr.c:232): Excess function parameter 'id' description in 'sub_alloc'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Compile warnings and errors (one on x86, two on ARM)
- WARNING in xen-pciback
- Use the acpi_processor_get_performance_info instead of the 'register'
version
* tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: remove redundant acpi/acpi_drivers.h include
xen: arm: mandate EABI and use generic atomic operations.
acpi: Export the acpi_processor_get_performance_info
xen/pciback: Don't disable a PCI device that is already disabled.
|
|
Add support for Altera 8250/16550 compatible serial port.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We can't forward declare enums.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Clean up interrupts on exit, silencing a sparse warning caused by
tps65912_irq_exit() being defined but not prototyped as we go.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Currently driver sets the irq type to IRQF_TRIGGER_LOW which is
causing interrupt registration failure in ARM based SoCs as:
[ 0.208479] genirq: Setting trigger mode 8 for irq 118 failed (gic_set_type+0x0/0xf0)
[ 0.208513] dummy 0-0059: Failed to request IRQ 118: -22
Provide the irq flags through platform data if device is registered
through board file or get the irq type from DT node property in place
of hardcoding the irq flag in driver to support multiple platforms.
Also configure the device to generate the interrupt signal according to
flag type.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace bugfixes from Eric Biederman:
"This is three simple fixes against 3.9-rc1. I have tested each of
these fixes and verified they work correctly.
The userns oops in key_change_session_keyring and the BUG_ON triggered
by proc_ns_follow_link were found by Dave Jones.
I am including the enhancement for mount to only trigger requests of
filesystem modules here instead of delaying this for the 3.10 merge
window because it is both trivial and the kind of change that tends to
bit-rot if left untouched for two months."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use nd_jump_link in proc_ns_follow_link
fs: Limit sys_mount to only request filesystem modules (Part 2).
fs: Limit sys_mount to only request filesystem modules.
userns: Stop oopsing in key_change_session_keyring
|
|
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull drm fixes from Dave Airlie:
"Misc radeon, nouveau, mgag200 and intel fixes.
The intel fixes should contain the fix for the touchpad on the
Chromebook - hey I'm an input maintainer now!"
Hate to pee on your parade, Dave, but I don't think being an input
maintainer is necessarily something to strive for..
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/tegra: drop "select DRM_HDMI"
drm: Documentation typo fixes
drm/mgag200: Bug fix: Renesas board now selects native resolution.
drm/mgag200: Reject modes that are too big for VRAM
drm/mgag200: 'fbdev_list' in 'struct mga_fbdev' is not used
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/nv50-: prevent some races between modesetting and page flipping
drm/nouveau/i2c: drop parent refcount when creating ports
drm/nv84: fix regression in page flipping
drm/nouveau: Fix typo in init_idx_addr_latched().
drm/nouveau: Disable AGP on PowerPC again.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that callback
from Rafael J Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from Nishanth
Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS code
from Rafael J Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix strictly
speaking, but the code in question went in through the PM tree).
* tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
|
|
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small things here and there, nothing major here really. The
conversion of twl4030ldo_ops to get_voltage_sel is a fix, as covered
in the commit log it fixes inconsistency in handling of the IS_UNSUP()
feature in the driver."
* tag 'regulator-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fixed regulator_bulk_enable unwinding code
regulator: twl: Convert twl4030ldo_ops to get_voltage_sel
regulator: palmas: fix number of SMPS voltages
regulator: core: fix documentation error in regulator_allow_bypass
regulator: core: update kernel documentation for regulator_desc
regulator: db8500-prcmu - remove incorrect __exit markup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Minor code cleanups and new Kconfig option to disable /dev/ecryptfs
The code cleanups fix up W=1 compiler warnings and some unnecessary
checks. The new Kconfig option, defaulting to N, allows the rarely
used eCryptfs kernel to userspace communication channel to be compiled
out. This may be the first step in it being eventually removed."
Hmm. I'm not sure whether these should be called "fixes", and it
probably should have gone in the merge window. But I'll let it slide.
* tag 'ecryptfs-3.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: allow userspace messaging to be disabled
eCryptfs: Fix redundant error check on ecryptfs_find_daemon_by_euid()
ecryptfs: ecryptfs_msg_ctx_alloc_to_free(): remove kfree() redundant null check
eCryptfs: decrypt_pki_encrypted_session_key(): remove kfree() redundant null check
eCryptfs: remove unneeded checks in virt_to_scatterlist()
eCryptfs: Fix -Wmissing-prototypes warnings
eCryptfs: Fix -Wunused-but-set-variable warnings
eCryptfs: initialize payload_len in keystore.c
|
|
The git commit d5aaffa9dd531c978c6f3fea06a2972653bd7fc8
(cpufreq: handle cpufreq being disabled for all exported function)
tightens the cpufreq API by returning errors when disable_cpufreq()
had been called.
The problem we are hitting is that the module xen-acpi-processor which
uses the ACPI's functions: acpi_processor_register_performance,
acpi_processor_preregister_performance, and acpi_processor_notify_smm
fails at acpi_processor_register_performance with -22.
Note that earlier during bootup in arch/x86/xen/setup.c there is also
an call to cpufreq's API: disable_cpufreq().
This is b/c we want the Linux kernel to parse the ACPI data, but leave
the cpufreq decisions to the hypervisor.
In v3.9 all the checks that d5aaffa9dd531c978c6f3fea06a2972653bd7fc8
added are now hit and the calls to cpufreq_register_notifier will now
fail. This means that acpi_processor_ppc_init ends up printing:
"Warning: Processor Platform Limit not supported"
and the acpi_processor_ppc_status is not set.
The repercussions of that is that the call to
acpi_processor_register_performance fails right away at:
if (!(acpi_processor_ppc_status & PPC_REGISTERED))
and we don't progress any further on parsing and extracting the _P*
objects.
The only reason the Xen code called that function was b/c it was
exported and the only way to gather the P-states. But we can also
just make acpi_processor_get_performance_info be exported and not
use acpi_processor_register_performance. This patch does so.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Pull networking fixes from David Miller:
"A moderately sized pile of fixes, some specifically for merge window
introduced regressions although others are for longer standing items
and have been queued up for -stable.
I'm kind of tired of all the RDS protocol bugs over the years, to be
honest, it's way out of proportion to the number of people who
actually use it.
1) Fix missing range initialization in netfilter IPSET, from Jozsef
Kadlecsik.
2) ieee80211_local->tim_lock needs to use BH disabling, from Johannes
Berg.
3) Fix DMA syncing in SFC driver, from Ben Hutchings.
4) Fix regression in BOND device MAC address setting, from Jiri
Pirko.
5) Missing usb_free_urb in ISDN Hisax driver, from Marina Makienko.
6) Fix UDP checksumming in bnx2x driver for 57710 and 57711 chips,
fix from Dmitry Kravkov.
7) Missing cfgspace_lock initialization in BCMA driver.
8) Validate parameter size for SCTP assoc stats getsockopt(), from
Guenter Roeck.
9) Fix SCTP association hangs, from Lee A Roberts.
10) Fix jumbo frame handling in r8169, from Francois Romieu.
11) Fix phy_device memory leak, from Petr Malat.
12) Omit trailing FCS from frames received in BGMAC driver, from Hauke
Mehrtens.
13) Missing socket refcount release in L2TP, from Guillaume Nault.
14) sctp_endpoint_init should respect passed in gfp_t, rather than use
GFP_KERNEL unconditionally. From Dan Carpenter.
15) Add AISX AX88179 USB driver, from Freddy Xin.
16) Remove MAINTAINERS entries for drivers deleted during the merge
window, from Cesar Eduardo Barros.
17) RDS protocol can try to allocate huge amounts of memory, check
that the user's request length makes sense, from Cong Wang.
18) SCTP should use the provided KMALLOC_MAX_SIZE instead of it's own,
bogus, definition. From Cong Wang.
19) Fix deadlocks in FEC driver by moving TX reclaim into NAPI poll,
from Frank Li. Also, fix a build error introduced in the merge
window.
20) Fix bogus purging of default routes in ipv6, from Lorenzo Colitti.
21) Don't double count RTT measurements when we leave the TCP receive
fast path, from Neal Cardwell."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: fix double-counted receiver RTT when leaving receiver fast path
CAIF: fix sparse warning for caif_usb
rds: simplify a warning message
net: fec: fix build error in no MXC platform
net: ipv6: Don't purge default router if accept_ra=2
net: fec: put tx to napi poll function to fix dead lock
sctp: use KMALLOC_MAX_SIZE instead of its own MAX_KMALLOC_SIZE
rds: limit the size allocated by rds_message_alloc()
MAINTAINERS: remove eexpress
MAINTAINERS: remove drivers/net/wan/cycx*
MAINTAINERS: remove 3c505
caif_dev: fix sparse warnings for caif_flow_cb
ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver
sctp: use the passed in gfp flags instead GFP_KERNEL
ipv[4|6]: correct dropwatch false positive in local_deliver_finish
l2tp: Restore socket refcount when sendmsg succeeds
net/phy: micrel: Disable asymmetric pause for KSZ9021
bgmac: omit the fcs
phy: Fix phy_device_free memory leak
bnx2x: Fix KR2 work-around condition
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes and cleanups from Thomas Gleixner:
"Commit e5ab012c3271 ("nohz: Make tick_nohz_irq_exit() irq safe") is
the first commit in the series and the minimal necessary bugfix, which
needs to go back into stable.
The remanining commits enforce irq disabling in irq_exit(), sanitize
the hardirq/softirq preempt count transition and remove a bunch of no
longer necessary conditionals."
I personally love getting rid of the very subtle and confusing
IRQ_EXIT_OFFSET thing. Even apart from the whole "more lines removed
than added" thing.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq: Don't re-enable interrupts at the end of irq_exit
irq: Remove IRQ_EXIT_OFFSET workaround
Revert "nohz: Make tick_nohz_irq_exit() irq safe"
irq: Sanitize invoke_softirq
irq: Ensure irq_exit() code runs with interrupts disabled
nohz: Make tick_nohz_irq_exit() irq safe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smpboot bugfix from Thomas Gleixner:
"A single bugfix for a regression introduced with the conversion of the
stop machine threads to the generic smpboot thread management
facility"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stop_machine: Mark per cpu stopper enabled early
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
"First round of iio fixes post the 3.9 merge window.
1) Some little fixes for the ad5064 dac driver.
2) A build warning 'fix' for a false positive in st_sensors
3) A couple of missing dependencies on IIO_BUFFER.
So nothing major and these mostly showed the advantages of the randconfig
builds various people have performed."
|
|
A few trivial fixes for composite driver:
Warning(include/linux/usb/composite.h:165): No description found for parameter
'fs_descriptors'
Warning(include/linux/usb/composite.h:165): Excess struct/union/enum/typedef
member 'descriptors' description in 'usb_function'
Warning(include/linux/usb/composite.h:321): No description found for parameter
'gadget_driver'
Warning(drivers/usb/gadget/composite.c:1777): Excess function parameter 'bind'
description in 'usb_composite_probe'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
|
|
After PCI and USB have stopped using the .find_bridge() callback in
struct acpi_bus_type, the only remaining user of it is SATA, but SATA
only pretends to be a user, because it points that callback to a stub
always returning -ENODEV.
For this reason, drop the SATA's dummy .find_bridge() callback and
remove .find_bridge(), which is not used any more, from struct
acpi_bus_type entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
|
|
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
|
|
When the userspace messaging (for the less common case of userspace key
wrap/unwrap via ecryptfsd) is not needed, allow eCryptfs to build with
it removed. This saves on kernel code size and reduces potential attack
surface by removing the /dev/ecryptfs node.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
|
|
Modify the request_module to prefix the file system type with "fs-"
and add aliases to all of the filesystems that can be built as modules
to match.
A common practice is to build all of the kernel code and leave code
that is not commonly needed as modules, with the result that many
users are exposed to any bug anywhere in the kernel.
Looking for filesystems with a fs- prefix limits the pool of possible
modules that can be loaded by mount to just filesystems trivially
making things safer with no real cost.
Using aliases means user space can control the policy of which
filesystem modules are auto-loaded by editing /etc/modprobe.d/*.conf
with blacklist and alias directives. Allowing simple, safe,
well understood work-arounds to known problematic software.
This also addresses a rare but unfortunate problem where the filesystem
name is not the same as it's module name and module auto-loading
would not work. While writing this patch I saw a handful of such
cases. The most significant being autofs that lives in the module
autofs4.
This is relevant to user namespaces because we can reach the request
module in get_fs_type() without having any special permissions, and
people get uncomfortable when a user specified string (in this case
the filesystem type) goes all of the way to request_module.
After having looked at this issue I don't think there is any
particular reason to perform any filtering or permission checks beyond
making it clear in the module request that we want a filesystem
module. The common pattern in the kernel is to call request_module()
without regards to the users permissions. In general all a filesystem
module does once loaded is call register_filesystem() and go to sleep.
Which means there is not much attack surface exposed by loading a
filesytem module unless the filesystem is mounted. In a user
namespace filesystems are not mounted unless .fs_flags = FS_USERNS_MOUNT,
which most filesystems do not set today.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
|
|
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
|
|
Pull second set of slave-dmaengine updates from Vinod Koul:
"Arnd's patch moves the dw_dmac to use generic DMA binding. I agreed
to merge this late as it will avoid the conflicts between trees.
The second patch from Matt adding a dma_request_slave_channel_compat
API was supposed to be picked up, but somehow never got picked up.
Some patches dependent on this are already in -next :("
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw_dmac: move to generic DMA binding
dmaengine: add dma_request_slave_channel_compat()
|