| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
These command do have variable length and the length can go up to 251,
so this changes the struct to not use a fixed size and then when
creating the PDU only the actual length of the data send to the
controller.
Fixes: a0fb3726ba551 ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
blacklist -> reject list
whitelist -> accept list
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> initiator
slave -> responder
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced when describing the
connectionless peripheral broadcast feature:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
These attributes are not used elsewhere in the code.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During command status or command complete event, the controller may set
ncmd=0 indicating that it is not accepting any more commands. In such a
case, host holds off sending any more commands to the controller. If the
controller doesn't recover from such condition, host will wait forever,
until the user decides that the Bluetooth is broken and may power cycles
the Bluetooth.
This patch triggers the hardware error to reset the controller and
driver when it gets into such state as there is no other wat out.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When an MGMT_EV_DEVICE_CONNECTED event is reported back to the user
space we will set the flags to tell if the established connection is
outbound or not. This is useful for the user space to log better metrics
and error messages.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.14
Second, and most likely the last, set of patches for v5.14. mt76 and
iwlwifi have most patches in this round, but rtw88 also has some new
features. Nothing special really standing out.
mt76
* mt7915 MSI support
* disable ASPM on mt7915
* mt7915 tx status reporting
* mt7921 decap offload
rtw88
* beacon filter support
* path diversity support
* firmware crash information via devcoredump
* quirks for disabling pci capabilities
mt7601u
* add USB ID for a XiaoDu WiFi Dongle
ath11k
* enable support for QCN9074 PCI devices
brcmfmac
* support parse country code map from DeviceTree
iwlwifi
* support for new hardware
* support for BIOS control of 11ax enablement in Russia
* support UNII4 band enablement from BIOS
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newly implemented fwnode_mdbiobus_register turned out to be
problematic - in case the fwnode_/of_/acpi_mdio are built as
modules, a dependency cycle can be observed during the depmod phase of
modules_install, eg.:
depmod: ERROR: Cycle detected: fwnode_mdio -> of_mdio -> fwnode_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
OR:
depmod: ERROR: Cycle detected: acpi_mdio -> fwnode_mdio -> acpi_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
A possible solution could be to rework fwnode_mdiobus_register,
so that to merge the contents of acpi_mdiobus_register and
of_mdiobus_register. However feasible, such change would
be very intrusive and affect huge amount of the of_mdiobus_register
users.
Since there are currently 2 users of ACPI and MDIO
(xgmac_mdio and mvmdio), withdraw the fwnode_mdbiobus_register
and roll back to a simple 'if' condition in affected drivers.
Fixes: 62a6ef6a996f ("net: mdiobus: Introduce fwnode_mdbiobus_register()")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the PLPMUTD probe will stop for a long period (interval * 30)
after it enters search complete state. If there's a pmtu change on the
route path, it takes a long time to be aware if the ICMP TooBig packet
is lost or filtered.
As it says in rfc8899#section-4.3:
"A DPLPMTUD method MUST NOT rely solely on this method."
(ICMP PTB message).
This patch is to enable the other method for search complete state:
"A PL can use the DPLPMTUD probing mechanism to periodically
generate probe packets of the size of the current PLPMTU."
With this patch, the probe will continue with the current pmtu every
'interval' until the PMTU_RAISE_TIMER 'timeout', which we implement
by adding raise_count to raise the probe size when it counts to 30
and removing the SCTP_PL_COMPLETE check for PMTU_RAISE_TIMER.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fallback case of fwnode_mdbiobus_register()
(relevant for !CONFIG_FWNODE_MDIO) was defined with wrong
argument name, causing a compilation error. Fix that.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's getting more common to run nested container environments for
testing cloud software. One of such examples is Kind [1] which runs a
Kubernetes cluster in Docker containers on a single host. Each container
acts as a Kubernetes node, and thus can run any Pod (aka container)
inside the former. This approach simplifies testing a lot, as it
eliminates complicated VM setups.
Unfortunately, such a setup breaks some functionality when cgroupv2 BPF
programs are used for load-balancing. The load-balancer BPF program
needs to detect whether a request originates from the host netns or a
container netns in order to allow some access, e.g. to a service via a
loopback IP address. Typically, the programs detect this by comparing
netns cookies with the one of the init ns via a call to
bpf_get_netns_cookie(NULL). However, in nested environments the latter
cannot be used given the Kubernetes node's netns is outside the init ns.
To fix this, we need to pass the Kubernetes node netns cookie to the
program in a different way: by extending getsockopt() with a
SO_NETNS_COOKIE option, the orchestrator which runs in the Kubernetes
node netns can retrieve the cookie and pass it to the program instead.
Thus, this is following up on Eric's commit 3d368ab87cf6 ("net:
initialize net->net_cookie at netns setup") to allow retrieval via
SO_NETNS_COOKIE. This is also in line in how we retrieve socket cookie
via SO_COOKIE.
[1] https://kind.sigs.k8s.io/
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Martynas Pumputis <m@lambda.lt>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit d26b698dd3cd ("net/tls: add skeleton of MIB statistics")
introduced __TLS_DEC_STATS(), but it is not used and __SNMP_DEC_STATS() is
not defined also. Let's remove it.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds two stats for the socket migration feature to evaluate the
effectiveness: LINUX_MIB_TCPMIGRATEREQ(SUCCESS|FAILURE).
If the migration fails because of the own_req race in receiving ACK and
sending SYN+ACK paths, we do not increment the failure stat. Then another
CPU is responsible for the req.
Link: https://lore.kernel.org/bpf/CAK6E8=cgFKuGecTzSCSQ8z3YJ_163C0uwO9yRvfDSE7vOe9mJA@mail.gmail.com/
Suggested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-net-next-2021-06-22
1) Various minor cleanups and fixes from net-next branch
2) Optimize mlx5 feature check on tx and
a fix to allow Vxlan with Ipsec offloads
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Skip non-SCTP packets in the new SCTP chunk support for nft_exthdr,
from Phil Sutter.
2) Simplify TCP option sanity check for TCP packets, also from Phil.
3) Add a new expression to store when the rule has been used last time.
4) Pass the hook state object to log function, from Florian Westphal.
5) Document the new sysctl knobs to tune the flowtable timeouts,
from Oz Shlomo.
6) Fix snprintf error check in the new nfnetlink_hook infrastructure,
from Dan Carpenter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As MISSED and DRAINING state are used to indicate a non-empty
qdisc, qdisc->empty is not longer needed, so remove it.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # flexcan
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently pfifo_fast has both TCQ_F_CAN_BYPASS and TCQ_F_NOLOCK
flag set, but queue discipline by-pass does not work for lockless
qdisc because skb is always enqueued to qdisc even when the qdisc
is empty, see __dev_xmit_skb().
This patch calls sch_direct_xmit() to transmit the skb directly
to the driver for empty lockless qdisc, which aviod enqueuing
and dequeuing operation.
As qdisc->empty is not reliable to indicate a empty qdisc because
there is a time window between enqueuing and setting qdisc->empty.
So we use the MISSED state added in commit a90c57f2cedd ("net:
sched: fix packet stuck problem for lockless qdisc"), which
indicate there is lock contention, suggesting that it is better
not to do the qdisc bypass in order to avoid packet out of order
problem.
In order to make MISSED state reliable to indicate a empty qdisc,
we need to ensure that testing and clearing of MISSED state is
within the protection of qdisc->seqlock, only setting MISSED state
can be done without the protection of qdisc->seqlock. A MISSED
state testing is added without the protection of qdisc->seqlock to
aviod doing unnecessary spin_trylock() for contention case.
As the enqueuing is not within the protection of qdisc->seqlock,
there is still a potential data race as mentioned by Jakub [1]:
thread1 thread2 thread3
qdisc_run_begin() # true
qdisc_run_begin(q)
set(MISSED)
pfifo_fast_dequeue
clear(MISSED)
# recheck the queue
qdisc_run_end()
enqueue skb1
qdisc empty # true
qdisc_run_begin() # true
sch_direct_xmit() # skb2
qdisc_run_begin()
set(MISSED)
When above happens, skb1 enqueued by thread2 is transmited after
skb2 is transmited by thread3 because MISSED state setting and
enqueuing is not under the qdisc->seqlock. If qdisc bypass is
disabled, skb1 has better chance to be transmited quicker than
skb2.
This patch does not take care of the above data race, because we
view this as similar as below:
Even at the same time CPU1 and CPU2 write the skb to two socket
which both heading to the same qdisc, there is no guarantee that
which skb will hit the qdisc first, because there is a lot of
factor like interrupt/softirq/cache miss/scheduling afffecting
that.
There are below cases that need special handling:
1. When MISSED state is cleared before another round of dequeuing
in pfifo_fast_dequeue(), and __qdisc_run() might not be able to
dequeue all skb in one round and call __netif_schedule(), which
might result in a non-empty qdisc without MISSED set. In order
to avoid this, the MISSED state is set for lockless qdisc and
__netif_schedule() will be called at the end of qdisc_run_end.
2. The MISSED state also need to be set for lockless qdisc instead
of calling __netif_schedule() directly when requeuing a skb for
a similar reason.
3. For netdev queue stopped case, the MISSED case need clearing
while the netdev queue is stopped, otherwise there may be
unnecessary __netif_schedule() calling. So a new DRAINING state
is added to indicate this case, which also indicate a non-empty
qdisc.
4. As there is already netif_xmit_frozen_or_stopped() checking in
dequeue_skb() and sch_direct_xmit(), which are both within the
protection of qdisc->seqlock, but the same checking in
__dev_xmit_skb() is without the protection, which might cause
empty indication of a lockless qdisc to be not reliable. So
remove the checking in __dev_xmit_skb(), and the checking in
the protection of qdisc->seqlock seems enough to avoid the cpu
consumption problem for netdev queue stopped case.
1. https://lkml.org/lkml/2021/5/29/215
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # flexcan
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qdisc->running seqcount operation is mainly used to do heuristic
locking on q->busylock for locked qdisc, see qdisc_is_running()
and __dev_xmit_skb().
So avoid doing seqcount operation for qdisc with TCQ_F_NOLOCK
flag.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # flexcan
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add wiphy_info_once() helper that prints info message only once.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511211549.30571-1-digetx@gmail.com
|
|
The inner_ipproto saves the inner IP protocol of the plain
text packet. This allows vendor's IPsec feature making offload
decision at skb's features_check and configuring hardware at
ndo_start_xmit.
For example, ConnectX6-DX IPsec device needs the plaintext's
IP protocol to support partial checksum offload on
VXLAN/GENEVE packet over IPsec transport mode tunnel.
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Huy Nguyen <huyn@nvidia.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch defined a new flag MPTCP_CAP_DENY_JOIN_ID0 for the third bit,
labeled "C" of the MP_CAPABLE option.
Add a new flag allow_join_id0 in struct mptcp_out_options. If this flag is
set, send out the MP_CAPABLE option with the flag MPTCP_CAP_DENY_JOIN_ID0.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, sctp over udp was using udp tunnel's icmp err process, which
only does sk lookup on sctp side. However for sctp's icmp error process,
there are more things to do, like syncing assoc pmtu/retransmit packets
for toobig type err, and starting proto_unreach_timer for unreach type
err etc.
Now after adding PLPMTUD, which also requires to process toobig type err
on sctp side. This patch is to process icmp err on sctp side by parsing
the type/code/info in .encap_err_lookup and call sctp's icmp processing
functions. Note as the 'redirect' err process needs to know the outer
ip(v6) header's, we have to leave it to udp(v6)_err to handle it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As described in rfc8899#section-5.2, when a probe succeeds, there might
be the following state transitions:
- Base -> Search, occurs when probe succeeds with BASE_PLPMTU,
pl.pmtu is not changing,
pl.probe_size increases by SCTP_PL_BIG_STEP,
- Error -> Search, occurs when probe succeeds with BASE_PLPMTU,
pl.pmtu is changed from SCTP_MIN_PLPMTU to SCTP_BASE_PLPMTU,
pl.probe_size increases by SCTP_PL_BIG_STEP.
- Search -> Search Complete, occurs when probe succeeds with the probe
size SCTP_MAX_PLPMTU less than pl.probe_high,
pl.pmtu is not changing, but update *pathmtu* with it,
pl.probe_size is set back to pl.pmtu to double check it.
- Search Complete -> Search, occurs when probe succeeds with the probe
size equal to pl.pmtu,
pl.pmtu is not changing,
pl.probe_size increases by SCTP_PL_MIN_STEP.
So search process can be described as:
1. When it just enters 'Search' state, *pathmtu* is not updated with
pl.pmtu, and probe_size increases by a big step (SCTP_PL_BIG_STEP)
each round.
2. Until pl.probe_high is set when a probe fails, and probe_size
decreases back to pl.pmtu, as described in the last patch.
3. When the probe with the new size succeeds, probe_size changes to
increase by a small step (SCTP_PL_MIN_STEP) due to pl.probe_high
is set.
4. Until probe_size is next to pl.probe_high, the searching finishes and
it goes to 'Complete' state and updates *pathmtu* with pl.pmtu, and
then probe_size is set to pl.pmtu to confirm by once more probe.
5. This probe occurs after "30 * probe_inteval", a much longer time than
that in Search state. Once it is done it goes to 'Search' state again
with probe_size increased by SCTP_PL_MIN_STEP.
As we can see above, during the searching, pl.pmtu changes while *pathmtu*
doesn't. *pathmtu* is only updated when the search finishes by which it
gets an optimal value for it. A big step is used at the beginning until
it gets close to the optimal value, then it changes to a small step until
it has this optimal value.
The small step is also used in 'Complete' until it goes to 'Search' state
again and the probe with 'pmtu + the small step' succeeds, which means a
higher size could be used. Then probe_size changes to increase by a big
step again until it gets close to the next optimal value.
Note that anytime when black hole is detected, it goes directly to 'Base'
state with pl.pmtu set to SCTP_BASE_PLPMTU, as described in the last patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The state transition is described in rfc8899#section-5.2,
PROBE_COUNT == MAX_PROBES means the probe fails for MAX times, and the
state transition includes:
- Base -> Error, occurs when BASE_PLPMTU Confirmation Fails,
pl.pmtu is set to SCTP_MIN_PLPMTU,
probe_size is still SCTP_BASE_PLPMTU;
- Search -> Base, occurs when Black Hole Detected,
pl.pmtu is set to SCTP_BASE_PLPMTU,
probe_size is set back to SCTP_BASE_PLPMTU;
- Search Complete -> Base, occurs when Black Hole Detected
pl.pmtu is set to SCTP_BASE_PLPMTU,
probe_size is set back to SCTP_BASE_PLPMTU;
Note a black hole is encountered when a sender is unaware that packets
are not being delivered to the destination endpoint. So it includes the
probe failures with equal probe_size to pl.pmtu, and definitely not
include that with greater probe_size than pl.pmtu. The later one is the
normal probe failure where probe_size should decrease back to pl.pmtu
and pl.probe_high is set. pl.probe_high would be used on HB ACK recv
path in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does exactly what rfc8899#section-6.2.1.2 says:
The SCTP sender needs to be able to determine the total size of a
probe packet. The HEARTBEAT chunk could carry a Heartbeat
Information parameter that includes, besides the information
suggested in [RFC4960], the probe size to help an implementation
associate a HEARTBEAT ACK with the size of probe that was sent. The
sender could also use other methods, such as sending a nonce and
verifying the information returned also contains the corresponding
nonce. The length of the PAD chunk is computed by reducing the
probing size by the size of the SCTP common header and the HEARTBEAT
chunk.
Note that HB ACK chunk will carry back whatever HB chunk carried, including
the probe_size we put it in; We also check hbinfo->probe_size in the HB ACK
against link->pl.probe_size to validate this HB ACK chunk.
v1->v2:
- Remove the unused 'sp' and add static for sctp_packet_bundle_pad().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 3 timers described in rfc8899#section-5.1.1:
PROBE_TIMER, PMTU_RAISE_TIMER, CONFIRMATION_TIMER
This patches adds a 'probe_timer' in transport, and it works as either
PROBE_TIMER or PMTU_RAISE_TIMER. At most time, it works as PROBE_TIMER
and expires every a 'probe_interval' time to send the HB probe packet.
When transport pl enters COMPLETE state, it works as PMTU_RAISE_TIMER
and expires in 'probe_interval * 30' time to go back to SEARCH state
and do searching again.
SCTP HB is an acknowledged packet, CONFIRMATION_TIMER is not needed.
The timer will start when transport pl enters BASE state and stop
when it enters DISABLED state.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are 4 constants described in rfc8899#section-5.1.2:
MAX_PROBES, MIN_PLPMTU, MAX_PLPMTU, BASE_PLPMTU;
And 2 variables described in rfc8899#section-5.1.3:
PROBED_SIZE, PROBE_COUNT;
And 5 states described in rfc8899#section-5.2:
DISABLED, BASE, SEARCH, SEARCH_COMPLETE, ERROR;
And these 4 APIs are used to reset/update PLPMTUD, check if PLPMTUD is
enabled, and calculate the additional headers length for a transport.
Note the member 'probe_high' in transport will be set to the probe
size when a probe fails with this probe size in the next patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this socket option, users can change probe_interval for
a transport, asoc or sock after it's created.
Note that if the change is for an asoc, also apply the change
to each transport in this asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PLPMTUD can be enabled by doing 'sysctl -w net.sctp.probe_interval=n'.
'n' is the interval for PLPMTUD probe timer in milliseconds, and it
can't be less than 5000 if it's not 0.
All asoc/transport's PLPMTUD in a new socket will be enabled by default.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This chunk is defined in rfc4820#section-3, and used to pad an
SCTP packet. The receiver must discard this chunk and continue
processing the rest of the chunks in the packet.
Add it now, as it will be bundled with a heartbeat chunk to probe
pmtu in the following patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct is not visible to user space and therefore should not use the
user visible data types.
Instead, use internal data types like other structures in the file.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ETHTOOL_A_MODULE_EEPROM_DATA' is a binary attribute, not a nested one.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The WWAN core not only multiplex the netdev configuration data, but
process it too, and needs some space to store its private data
associated with the netdev. Add a structure to keep common WWAN core
data. The structure will be stored inside the netdev private data before
WWAN driver private data and have a field to make it easier to access
the driver data. Also add a helper function that simplifies drivers
access to their data.
At the moment we use the common WWAN private data to store the WWAN data
link (channel) id at the time the link is created, and report it back to
user using the .fill_info() RTNL callback. This should help the user to
be aware which network interface is bound to which WWAN device data
channel.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
CC: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most, if not each WWAN device driver will create a netdev for the
default data channel. Therefore, add an option for the WWAN netdev ops
registration function to create a default netdev for the WWAN device.
A WWAN device driver should pass a default data channel link id to the
ops registering function to request the creation of a default netdev, or
a special value WWAN_NO_DEFAULT_LINK to inform the WWAN core that the
default netdev should not be created.
For now, only wwan_hwsim utilize the default link creation option. Other
drivers will be reworked next.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
CC: M Chetan Kumar <m.chetan.kumar@intel.com>
CC: Intel Corporation <linuxwwan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The WWAN netdev ops owner holding was used to protect from the
unexpected memory disappear. This approach causes a dependency cycle
(driver -> core -> driver) and effectively prevents a WWAN driver
unloading. E.g. WWAN hwsim could not be unloaded until all simulated
devices are removed:
~# modprobe wwan_hwsim devices=2
~# lsmod | grep wwan
wwan_hwsim 16384 2
wwan 20480 1 wwan_hwsim
~# rmmod wwan_hwsim
rmmod: ERROR: Module wwan_hwsim is in use
~# echo > /sys/kernel/debug/wwan_hwsim/hwsim0/destroy
~# echo > /sys/kernel/debug/wwan_hwsim/hwsim1/destroy
~# lsmod | grep wwan
wwan_hwsim 16384 0
wwan 20480 1 wwan_hwsim
~# rmmod wwan_hwsim
For a real device driver this will cause an inability to unload module
until a served device is physically detached.
Since the last commit we are removing all child netdev(s) when a driver
unregister the netdev ops. This allows us to permit the driver
unloading, since any sane driver will call ops unregistering on a device
deinitialization. So, remove the holding of an ops owner to make it
easier to unload a driver module. The owner field has also beed removed
from the ops structure as there are no more users of this field.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new helper function that
wraps acpi_/of_ mdiobus_register() and allows its
usage via common fwnode_ interface.
Fall back to raw mdiobus_register() in case CONFIG_FWNODE_MDIO
is not enabled, in order to satisfy compatibility
in all future user drivers.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 3b707c3008ca ("net: dev_is_mac_header_xmit() true for
ARPHRD_RAWIP"), add ARPHRD_IP6GRE to dev_is_mac_header_xmit(), to make
ip6gre compatible with act_mirred and __bpf_redirect().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The difference between dsa_is_user_port and dsa_port_is_user is that the
former needs to look up the list of ports of the DSA switch tree in
order to find the struct dsa_port, while the latter directly receives it
as an argument.
dsa_is_user_port is already in widespread use and has its place, so
there isn't any chance of converting all callers to a single form.
But being able to do:
dsa_port_is_user(dp)
instead of
dsa_is_user_port(dp->ds, dp->index)
is much more efficient too, especially when the "dp" comes from an
iterator over the DSA switch tree - this reduces the complexity from
quadratic to linear.
Move these helpers from dsa2.c to include/net/dsa.h so that others can
use them too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc7, including fixes from wireless, bpf,
bluetooth, netfilter and can.
Current release - regressions:
- mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()
to fix modifying offloaded qdiscs
- lantiq: net: fix duplicated skb in rx descriptor ring
- rtnetlink: fix regression in bridge VLAN configuration, empty info
is not an error, bot-generated "fix" was not needed
- libbpf: s/rx/tx/ typo on umem->rx_ring_setup_done to fix umem
creation
Current release - new code bugs:
- ethtool: fix NULL pointer dereference during module EEPROM dump via
the new netlink API
- mlx5e: don't update netdev RQs with PTP-RQ, the special purpose
queue should not be visible to the stack
- mlx5e: select special PTP queue only for SKBTX_HW_TSTAMP skbs
- mlx5e: verify dev is present in get devlink port ndo, avoid a panic
Previous releases - regressions:
- neighbour: allow NUD_NOARP entries to be force GCed
- further fixes for fallout from reorg of WiFi locking (staging:
rtl8723bs, mac80211, cfg80211)
- skbuff: fix incorrect msg_zerocopy copy notifications
- mac80211: fix NULL ptr deref for injected rate info
- Revert "net/mlx5: Arm only EQs with EQEs" it may cause missed IRQs
Previous releases - always broken:
- bpf: more speculative execution fixes
- netfilter: nft_fib_ipv6: skip ipv6 packets from any to link-local
- udp: fix race between close() and udp_abort() resulting in a panic
- fix out of bounds when parsing TCP options before packets are
validated (in netfilter: synproxy, tc: sch_cake and mptcp)
- mptcp: improve operation under memory pressure, add missing
wake-ups
- mptcp: fix double-lock/soft lookup in subflow_error_report()
- bridge: fix races (null pointer deref and UAF) in vlan tunnel
egress
- ena: fix DMA mapping function issues in XDP
- rds: fix memory leak in rds_recvmsg
Misc:
- vrf: allow larger MTUs
- icmp: don't send out ICMP messages with a source address of 0.0.0.0
- cdc_ncm: switch to eth%d interface naming"
* tag 'net-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (139 commits)
net: ethernet: fix potential use-after-free in ec_bhf_remove
selftests/net: Add icmp.sh for testing ICMP dummy address responses
icmp: don't send out ICMP messages with a source address of 0.0.0.0
net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY
net: ll_temac: Fix TX BD buffer overwrite
net: ll_temac: Add memory-barriers for TX BD access
net: ll_temac: Make sure to free skb when it is completely used
MAINTAINERS: add Guvenc as SMC maintainer
bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path
bnxt_en: Fix TQM fastpath ring backing store computation
bnxt_en: Rediscover PHY capabilities after firmware reset
cxgb4: fix wrong shift.
mac80211: handle various extensible elements correctly
mac80211: reset profile_periodicity/ema_ap
cfg80211: avoid double free of PMSR request
cfg80211: make certificate generation more robust
mac80211: minstrel_ht: fix sample time check
net: qed: Fix memcpy() overflow of qed_dcbx_params()
net: cdc_eem: fix tx fixup skb leak
net: hamradio: fix memory leak in mkiss_close
...
|
|
At the moment, the WWAN core provides wwan_port_txon/off() to implement
blocking writes. The tx() port operation should not block, instead
wwan_port_txon/off() should be called when the TX queue is full or has
free space again.
However, in some cases it is not straightforward to make use of that
functionality. For example, the RPMSG API used by rpmsg_wwan_ctrl.c
does not provide any way to be notified when the TX queue has space
again. Instead, it only provides the following operations:
- rpmsg_send(): blocking write (wait until there is space)
- rpmsg_trysend(): non-blocking write (return error if no space)
- rpmsg_poll(): set poll flags depending on TX queue state
Generally that's totally sufficient for implementing a char device,
but it does not fit well to the currently provided WWAN port ops.
Most of the time, using the non-blocking rpmsg_trysend() in the
WWAN tx() port operation works just fine. However, with high-frequent
writes to the char device it is possible to trigger a situation
where this causes issues. For example, consider the following
(somewhat unrealistic) example:
# dd if=/dev/zero bs=1000 of=/dev/wwan0qmi0
dd: error writing '/dev/wwan0qmi0': Resource temporarily unavailable
1+0 records out
This fails immediately after writing the first record. It's likely
only a matter of time until this triggers issues for some real application
(e.g. ModemManager sending a lot of large QMI packets).
The rpmsg_char device does not have this problem, because it uses
rpmsg_trysend() and rpmsg_poll() to support non-blocking operations.
Make it possible to use the same in the RPMSG WWAN driver by adding
two new optional wwan_port_ops:
- tx_blocking(): send data blocking if allowed
- tx_poll(): set additional TX poll flags
This integrates nicely with the RPMSG API and does not require
any change in existing WWAN drivers.
With these changes, the dd example above blocks instead of exiting
with an error.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most device_id structs provide a driver_data field that can be used
by drivers to associate data more easily for a particular device ID.
Add the same for the rpmsg_device_id.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1f3c98eaddec857e16a7a1c6cd83317b3dc89438.
Does not build...
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the pr_info content from int to char *, this looks more readable.
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When constructing ICMP response messages, the kernel will try to pick a
suitable source address for the outgoing packet. However, if no IPv4
addresses are configured on the system at all, this will fail and we end up
producing an ICMP message with a source address of 0.0.0.0. This can happen
on a box routing IPv4 traffic via v6 nexthops, for instance.
Since 0.0.0.0 is not generally routable on the internet, there's a good
chance that such ICMP messages will never make it back to the sender of the
original packet that the ICMP message was sent in response to. This, in
turn, can create connectivity and PMTUd problems for senders. Fortunately,
RFC7600 reserves a dummy address to be used as a source for ICMP
messages (192.0.0.8/32), so let's teach the kernel to substitute that
address as a last resort if the regular source address selection procedure
fails.
Below is a quick example reproducing this issue with network namespaces:
ip netns add ns0
ip l add type veth peer netns ns0
ip l set dev veth0 up
ip a add 10.0.0.1/24 dev veth0
ip a add fc00:dead:cafe:42::1/64 dev veth0
ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2
ip -n ns0 l set dev veth0 up
ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0
ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1
ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0
ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1
tcpdump -tpni veth0 -c 2 icmp &
ping -w 1 10.1.0.1 > /dev/null
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64
IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
2 packets captured
2 packets received by filter
0 packets dropped by kernel
With this patch the above capture changes to:
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64
IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Juliusz Chroboczek <jch@irif.fr>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mptcp_dump_mpext, dump the csum fields, csum and csum_reqd in struct
mptcp_dump_mpext too.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new member named csum in struct mptcp_options_received.
When parsing the MP_CAPABLE with data, if the checksum is enabled,
adjust the expected_opsize. If the receiving option length matches the
length with the data checksum, get the checksum value and save it in
mp_opt->csum. And in mptcp_incoming_options, pass it to mpext->csum.
We always parse any csum/nocsum combination and delay the presence check
to later code, to allow reset if missing.
Additionally, in the TX path, use the newly introduce ext field to avoid
MPTCP csum recomputation on TCP retransmission and unneeded csum update
on when setting the data fin_flag.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
