| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.17
A few more updates for v5.17, nothing hugely stand out in the few days
since the initial pull request was sent.
|
|
The cs35l41 supports a low power DSP memory retention mode. Add support
for entering this mode when then device is not in use.
Co-authored-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220107160636.6555-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for the addition of PM runtime support move the test
key out of the register patches themselves. This is necessary to
allow the test key to be held during cache synchronisation, which is
required by the OTP settings which were unpacked from the device and
written by the driver.
Also whilst at it, the driver uses a mixture of accessing the test key
register by name and by address, consistently use the name.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220107160636.6555-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.17
Not much going on framework release this time, but a big update for
drivers especially the Intel and SOF ones.
- Refinements and cleanups around the delay() APIs.
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code.
- Support for pin switches in simple-card derived cards.
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx.
|
|
Pull 5.17 materials.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ASoC and HDA will use the same registers to configure
internal boost for the device
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-7-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will use the same register to set channels
for the device
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-6-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA systems require the same errata patches, so
move it to the shared code using a function the correctly
applies the patches by revision
Also, move CS35L41_DSP1_CCM_CORE_CTRL write to errata
patch function as is required to be written at boot,
but not in regmap_register_patch sequence as will affect
waking up from hibernation
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-5-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC and HDA will do the same cs35l41_otp_unpack, so move it
to shared code
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211217115708.882525-3-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To support CS35L41 in HDA systems the HDA driver
for CS35L41 would have to duplicate some functions
that already exist on ASoC driver
So instead of duplicate the code, use the new lib
source as a shared resource for both ASoC and HDA
Also, change the way CONFIG_SND_SOC_CS35L41 is
selected, as reported by Intel Kernel test robot,
it is possible to build SND_SOC_CS35L41_SPI/I2C
without the main driver, which would lead to build
failures.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211217115708.882525-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The existing code maximizes confusion by using 'stream' and 'hstream'
variables of different types. Examples:
struct hdac_stream *stream;
struct hdac_ext_stream *stream;
struct hdac_stream *hstream;
struct hdac_ext_stream *hstream;
with some additional copy/paste remains:
struct hdac_ext_stream *azx_dev;
This patch suggests a consistent naming across all 'hdac_ext_stream'
functions. The convention is:
struct hdac_stream *hstream;
struct hdac_ext_stream *hext_stream;
No functionality change - just renaming of variables and more
consistent indentation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20211216231128.344321-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_hdac_ext_stop_streams() has really nothing to do with the
extension, it just loops over the bus streams.
Move it to the hdac_stream layer and rename to remove the 'ext'
prefix and add the precision that the chip will also be stopped.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211216231128.344321-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The HDAudio ASoC support relies on the set_tdm_slots() helper to store
the HDaudio stream tag in the tx_mask. This only works because of the
pre-existing order in soc-pcm.c, where the hw_params() is handled for
codec_dais *before* cpu_dais. When the order is reversed, the
stream_tag is used as a mask in the codec fixup functions:
/* fixup params based on TDM slot masks */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
codec_dai->tx_mask)
soc_pcm_codec_params_fixup(&codec_params,
codec_dai->tx_mask);
As a result of this confusion, the codec_params_fixup() ends-up
generating bad channel masks, depending on what stream_tag was
allocated.
We could add a flag to state that the tx_mask is really not a mask,
but it would be quite ugly to persist in overloading concepts.
Instead, this patch suggests a more generic get/set 'stream' API based
on the existing model for SoundWire. We can expand the concept to
store 'stream' opaque information that is specific to different DAI
types. In the case of HDAudio DAIs, we only need to store a stream tag
as an unsigned char pointer. The TDM rx_ and tx_masks should really
only be used to store masks.
Rename get_sdw_stream/set_sdw_stream callbacks and helpers as
get_stream/set_stream. No functionality change beyond the rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ASoC core already has several helpers to parse card properties
from the device tree. Move the parsing code for "pin-switches" from
simple-card-utils to a shared snd_soc_of_parse_pin_switches() function
so other drivers can also use it to set up pin switches configured in
the device tree.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since there is nothing SND about the firmware state, rename the enum
from `snd_sof_fw_state` to simply `sof_fw_state`
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the enum snd_sof_fw_state to include/sound/sof.h to be accessible
outside of the core SOF stack.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Dmitry Osipenko <digetx@gmail.com>:
This series revives Tegra20 S/PDIF driver which was upstreamed long time
ago, but never was used. It also turns Tegra DRM HDMI driver into HDMI
audio CODEC provider. Finally, HDMI audio is enabled in device-trees.
For now the audio is enable only for Acer A500 tablet and Toshiba AC100
netbook because they're already supported by upstream, later on ASUS TF101
tablet will join them.
I based S/PDIF patches on Arnd's Bergmann patch from a separate series [1]
that removes obsolete slave_id. This eases merging of the patches by
removing the merge conflict. This is a note for Mark Brown.
I also based this series on top of power management series [2]. I.e. [2]
should be applied first, otherwise "Add S/PDIF node to Tegra20 device-tree"
patch should have merge conflict. This is a note for Thierry.
[1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=273312
[2] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=274534
Changelog:
v4: - Added patches that update multi_v7_defconfig with the enabled S/PDIF
and APB DMA drivers.
v3: - Renamed S/PDIF device-tree clocks as was suggested by Rob Herring.
- Added r-bs and acks that were given by Rob Herring to v2.
v2: - Corrected I2S yaml problem that was reported by the DT bot for v1
by removing the non-existent required clock-names property.
- Removed assigned-clocks property from S/PDIF yaml since this property
is now inherited from the clocks property.
- Reordered the "tegra20: spdif: Set FIFO trigger level" patch, making
it the first sound/soc patch in the series, like it was suggested by
Mark Brown in the comment to v1. Also reworded commit message of this
patch to *not* make it looks like it should be backported to stable
kernels.
Arnd Bergmann (1):
ASoC: tegra20-spdif: stop setting slave_id
Dmitry Osipenko (21):
ASoC: dt-bindings: Add binding for Tegra20 S/PDIF
ASoC: dt-bindings: tegra20-i2s: Convert to schema
ASoC: dt-bindings: tegra20-i2s: Document new nvidia,fixed-parent-rate
property
dt-bindings: host1x: Document optional HDMI sound-dai-cells
ASoC: tegra20: spdif: Set FIFO trigger level
ASoC: tegra20: spdif: Support device-tree
ASoC: tegra20: spdif: Improve driver's code
ASoC: tegra20: spdif: Use more resource-managed helpers
ASoC: tegra20: spdif: Reset hardware
ASoC: tegra20: spdif: Support system suspend
ASoC: tegra20: spdif: Filter out unsupported rates
ASoC: tegra20: i2s: Filter out unsupported rates
drm/tegra: hdmi: Unwind tegra_hdmi_init() errors
drm/tegra: hdmi: Register audio CODEC on Tegra20
ARM: tegra_defconfig: Enable S/PDIF driver
ARM: config: multi v7: Enable NVIDIA Tegra20 S/PDIF driver
ARM: config: multi v7: Enable NVIDIA Tegra20 APB DMA driver
ARM: tegra: Add S/PDIF node to Tegra20 device-tree
ARM: tegra: Add HDMI audio graph to Tegra20 device-tree
ARM: tegra: acer-a500: Enable S/PDIF and HDMI audio
ARM: tegra: paz00: Enable S/PDIF and HDMI audio
.../display/tegra/nvidia,tegra20-host1x.txt | 1 +
.../bindings/sound/nvidia,tegra20-i2s.txt | 30 ---
.../bindings/sound/nvidia,tegra20-i2s.yaml | 77 +++++++
.../bindings/sound/nvidia,tegra20-spdif.yaml | 85 ++++++++
.../boot/dts/tegra20-acer-a500-picasso.dts | 8 +
arch/arm/boot/dts/tegra20-paz00.dts | 8 +
arch/arm/boot/dts/tegra20.dtsi | 40 +++-
arch/arm/configs/multi_v7_defconfig | 2 +
arch/arm/configs/tegra_defconfig | 1 +
drivers/gpu/drm/tegra/Kconfig | 3 +
drivers/gpu/drm/tegra/hdmi.c | 168 +++++++++++++--
sound/soc/tegra/tegra20_i2s.c | 49 +++++
sound/soc/tegra/tegra20_spdif.c | 197 ++++++++++++------
sound/soc/tegra/tegra20_spdif.h | 1 +
sound/soc/tegra/tegra_pcm.c | 6 +
sound/soc/tegra/tegra_pcm.h | 1 +
16 files changed, 574 insertions(+), 103 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt
create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.yaml
create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-spdif.yaml
--
2.33.1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine into v4_20211204_digetx_support_hdmi_audio_on_nvidia_tegra20
dmaengine_topic_slave_id_removal_5.17
Tag for dmaengine slave_id removal topic branch which should be merged
into v5.17
|
|
Newly added shared heap zones should be taken into account during
memory usage scanning.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211216232422.345164-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This field is no longer set from any driver now, so remove the
last references as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
On start/pause_release/resume, when more than one FE is connected to
the same BE, it's possible that the trigger is sent more than
once. This is not desirable, we only want to trigger a BE once, which
is straightforward to implement with a refcount.
For stop/pause/suspend, the problem is more complicated: the check
implemented in snd_soc_dpcm_can_be_free_stop() may fail due to a
conceptual deadlock when we trigger the BE before the FE. In this
case, the FE states have not yet changed, so there are corner cases
where the TRIGGER_STOP is never sent - the dual case of start where
multiple triggers might be sent.
This patch suggests an unconditional trigger in all cases, without
checking the FE states, using a refcount protected by the BE PCM
stream lock.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The existing locking for DPCM has several issues
a) a confusing mix of card->mutex and card->pcm_mutex.
b) a dpcm_lock spinlock added inconsistently and on paths that could
be recursively taken. The use of irqsave/irqrestore was also overkill.
The suggested model is:
1) The pcm_mutex is the top-most protection of BE links in the FE. The
pcm_mutex is applied always on either the top PCM callbacks or the
external call from DAPM, not taken in the internal functions.
2) the FE stream lock is taken in higher levels before invoking
dpcm_be_dai_trigger()
3) when adding and deleting a BE, both the pcm_mutex and FE stream
lock are taken.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[clarification of commit message by plbossart]
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
formats
Regarding to handling [U|S][32|24] PCM formats, many userspace
application developers and driver developers have confusion, since they
require them to understand justification or padding. It easily
loses consistency and soundness to operate with many type of devices. In
this commit, I attempt to solve the situation by adding comment about
relation between [S|U]32 formats and 'msbits' hardware parameter.
The formats are used for 'left-justified' sample format, and the available
bit count in most significant bit is delivered to userspace in msbits
hardware parameter (struct snd_pcm_hw_params.msbits), which is decided by
msbits constraint added by pcm drivers (snd_pcm_hw_constraint_msbits()).
In driver side, the msbits constraint includes two elements; the physical
width of format and the available width of the format in most significant
bit. The former is used to match SAMPLE_BITS of format. (For my
convenience, I ignore wildcard in the usage of the constraint.)
As a result of interaction between ALSA pcm core and ALSA pcm application,
when the format in which SAMPLE_BITS equals to physical width of the
msbits constaint, the msbits parameter is set by referring to the
available width of the constraint. When the msbits parameter is not
changed in the above process, ALSA pcm core set it alternatively with
SAMPLE_BIT of chosen format.
In userspace application side, the msbits is only available after calling
ioctl(2) with SNDRV_PCM_IOCTL_HW_PARAMS request. Even if the hardware
parameter structure includes somewhat value of SAMPLE_BITS interval
parameter as width of format, all of the width is not always available
since msbits can be less than the width.
I note that [S|U]24 formats are used for 'right-justified' 24 bit sample
formats within 32 bit frame. The first byte in most significant bit
should be invalidated. Although the msbits exposed to userspace should be
zero as invalid value, actually it is 32 from physical width of format.
[ corrected typos -- tiwai ]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210529033353.21641-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There is a pop noise at the beginning of the capture data.
This patch adds the delay time before stereo1 ADC unmute to fix the pop sound issue.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20211208101718.28945-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-5.17 so we can apply new Tegra work
|
|
Two key operations missings are: endpoint presence-check and retrieval
of matching endpoint hardware configuration (blob). Add operations for
both use cases.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211126140355.1042684-2-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Current soc-pcm.c :: soc_pcm_pointer() is assuming that
component driver might update runtime->delay silently in
snd_soc_pcm_component_pointer() (= A).
static snd_pcm_uframes_t soc_pcm_pointer(...)
{
...
/* clearing the previous total delay */
=> runtime->delay = 0;
(A) offset = snd_soc_pcm_component_pointer(substream);
/* base delay if assigned in pointer callback */
=> delay = runtime->delay;
...
}
1) The behavior that ".pointer callback secretly updates
runtime->delay" is strange and confusable.
2) Current snd_soc_pcm_component_pointer() uses 1st found component's
.pointer callback only, thus it is no problem for now.
But runtime->delay might be overwrote if it adjusted to multiple
components in the future.
3) Component delay is updated at .pointer callback timing (secretly).
But some components which doesn't have .pointer callback might want
to increase runtime->delay for some reasons.
We already have .delay function for DAI, but not have for Component.
This patch adds new snd_soc_pcm_component_delay() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874k8cy25t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_pcm_pointer() is manually calculating
both CPU-DAI's max delay (= A)
and Codec-DAI's max delay (= B).
static snd_pcm_uframes_t soc_pcm_pointer(...)
{
...
^ for_each_rtd_cpu_dais(rtd, i, cpu_dai)
(A) cpu_delay = max(cpu_delay, ...);
v delay += cpu_delay;
^ for_each_rtd_codec_dais(rtd, i, codec_dai)
(B) codec_delay = max(codec_delay, ...);
v delay += codec_delay;
runtime->delay = delay;
...
}
Current soc_pcm_pointer() and the total delay calculating
is not readable / difficult to understand.
This patch update snd_soc_dai_delay() to snd_soc_pcm_dai_delay(),
and calcule both CPU/Codec delay in one function.
Link: https://lore.kernel.org/r/87fszl4yrq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yssy25z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some DAI components, such as HDaudio, need to be stopped in two steps
a) stop the DAI component
b) stop the DAI DMA
This patch enables this two-step stop by expanding the DAI_CONFIG
IPC flags and split them into 2 parts.
The 4 LSB bits indicate when the DAI_CONFIG IPC is sent, ex: hw_params,
hw_free or pause. The 4 MSB bits are used as the quirk flags to be used
along with the command flags. The quirk flag called
SOF_DAI_CONFIG_FLAGS_2_STEP_STOP shall be set along with the HW_PARAMS
command flag, i.e. before the pipeline is started so that the stop/pause
trigger op in the FW can take the appropriate action to either
perform/skip the DMA stop. If set, the DMA stop will be executed when
the DAI_CONFIG IPC is sent during hw_free. In the case of pause, DMA
pause will be handled when the DAI_CONFIG IPC is sent with the PAUSE
command flag.
Along with this, modify the signature for the hda_ctrl_dai_widget_setup/
hda_ctrl_dai_widget_free() functions to take additional flags as an
argument and modify all users to pass the appropriate quirk flags. Only
the HDA DAI's need to pass the SOF_DAI_CONFIG_FLAGS_2_STEP_STOP quirk
flag during hw_params to indicate that it supports two-step stop and
pause.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211125101520.291581-10-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.16
There's a large but repetitive set of fixes here for issues with the
Tegra kcontrols not correctly reporting changes to userspace, a fix for
some issues with matching on older x86 platforms introduced during the
merge window together with a set of smaller fixes and one new system
quirk.
|
|
Commit dac7cbd55dca ("ASoC: Intel: soc-acpi-byt: shrink tables using
compatible IDs") and commit 959ae8215a9e ("ASoC: Intel: soc-acpi-cht:
shrink tables using compatible IDs") simplified the match tables in
soc-acpi-intel-byt-match.c and soc-acpi-intel-cht-match.c by merging
identical entries using the new .comp_ids snd_soc_acpi_mach field to
point a single entry to multiple ACPI HIDs and clearing the previously
unique per entry .id field.
But various machine drivers from sound/soc/intel/boards rely on mach->id
in one or more ways, e.g. some drivers contain the following snippets:
adev = acpi_dev_get_first_match_dev(mach->id, NULL, -1);
pkg_found = snd_soc_acpi_find_package_from_hid(mach->id, ...
if (!strncmp(snd_soc_cards[i].codec_id, mach->id, 8)) { ...
All of which are broken by the match table shrinking.
Make the snd_soc_acpi_mach.id field non const (the storage for the tables
already is non const) and on a comps_ids match copy the matching HID to
the id field to fix this.
Fixes: dac7cbd55dca ("ASoC: Intel: soc-acpi-byt: shrink tables using compatible IDs")
Fixes: 959ae8215a9e ("ASoC: Intel: soc-acpi-cht: shrink tables using compatible IDs")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Brent Lu <brent.lu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211118153014.349222-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add new sof dai and config to pass topology file configuration
to SOF firmware running on Mediatek platform DSP core.
Add mediatek audio front end(AFE) to the list of supported sof_dais
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211118100749.54628-4-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add new sof dais and config to pass topology file configuration
to SOF firmware running on ACP's DSP core. ACP firmware support
I2S_BT, I2S_SP and DMIC controller hence add three new dais to
the list of supported sof_dais
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-12-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is a second attempt to unify the x86-specific SG-buffer handling
code with the new standard non-contiguous page handler.
The first try (in commit 2d9ea39917a4) failed due to the wrong page
and address calculations, hence reverted. (And the second try failed
due to a copy&paste error.) Now it's corrected with the previous fix
for noncontig pages, and the proper sg page iteration by this patch.
After the migration, SNDRV_DMA_TYPE_DMA_SG becomes identical with
SNDRV_DMA_TYPE_NONCONTIG on x86, while others still fall back to
SNDRV_DMA_TYPE_DEV.
Tested-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Tested-by: Harald Arnesen <harald@skogtun.org>
Link: https://lore.kernel.org/r/20211017074859.24112-4-tiwai@suse.de
Link: https://lore.kernel.org/r/20211109062235.22310-1-tiwai@suse.de
Link: https://lore.kernel.org/r/20211116073358.19741-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When a codec is unbound dynamically via sysfs while its stream is in
use, we may face a potential deadlock at the proc remove or a UAF.
This happens since the hda_pcm is managed by a linked list, as it
handles the hda_pcm object release via kref.
When a PCM is opened at the unbinding time, the release of hda_pcm
gets delayed and it ends up with the close of the PCM stream releasing
the associated hda_pcm object of its own. The hda_pcm destructor
contains the PCM device release that includes the removal of procfs
entries. And, this removal has the sync of the close of all in-use
files -- which would never finish because it's called from the PCM
file descriptor itself, i.e. it's trying to shoot its foot.
For addressing the deadlock above, this patch changes the way to
manage and release the hda_pcm object. The kref of hda_pcm is
dropped, and instead a simple refcount is introduced in hda_codec for
keeping the track of the active PCM streams, and at each PCM open and
close, this refcount is adjusted accordingly. At unbinding, the
driver calls snd_device_disconnect() for each PCM stream, then
synchronizes with the refcount finish, and finally releases the object
resources.
Fixes: bbbc7e8502c9 ("ALSA: hda - Allocate hda_pcm objects dynamically")
Link: https://lore.kernel.org/r/20211116072459.18930-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a new SOF_IPC_TRACE_DMA_FREE IPC command to stop and free trace DMA
in the FW.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211102101019.14037-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 2d9ea39917a4e4293bc2caea902c7059a330b611.
We've got a regression report showing that the audio got broken the
device over AMD IOMMU. The conversion assumed the wrong pointer /
page mapping for the indirect mapping case, and we need to correct
this urgently, so let's revert it for now.
Fixes: 2d9ea39917a4 ("ALSA: memalloc: Convert x86 SG-buffer handling with non-contiguous type")
Reported-and-tested-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Link: https://lore.kernel.org/r/20211104180846.16340-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.16
This is an unusually large set of updates, mostly a large crop of
unusually big drivers coupled with extensive overhauls of existing code.
There's a SH change here for the DAI format terminology, the change is
straightforward and the SH maintainers don't seem very active.
- A new version of the audio graph card which supports a wider range of
systems.
- Move of the Cirrus DSP framework into drivers/firmware to allow for
future use by non-audio DSPs.
- Several conversions to YAML DT bindings.
- Continuing cleanups to the SOF and Intel code.
- A very big overhaul of the cs42l42 driver, correcting many problems.
- Support for AMD Vangogh and Yelow Cap, Cirrus CS35L41, Maxim
MAX98520 and MAX98360A, Mediatek MT8195, Nuvoton NAU8821, nVidia
Tegra210, NXP i.MX8ULP, Qualcomm AudioReach, Realtek ALC5682I-VS,
RT5682S, and RT9120 and Rockchip RV1126 and RK3568
|
|
A machine driver needs to be enumerated by more than one ACPI HID if
it supports second headphone driver (i.e. rt5682 and rt5682s).
However, the id field in snd_soc_acpi_mach structure could contain
only one HID. By adding a 'comp_ids' field which can contain several
HIDs, we can enumerate a machine driver by multiple ACPI HIDs.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Link: https://lore.kernel.org/r/20211029171409.611600-2-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When removing the index argument from snd_soc_topology_component_remove()
commit a5b8f71c5477f (ASoC: topology: Remove multistep topology loading)
forgot to update the stub for !SND_SOC_TOPOLOGY use, causing build failures
for anything that tries to make use of it.
Fixes: a5b8f71c5477f (ASoC: topology: Remove multistep topology loading)
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211025154844.2342120-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_dma_buffer_sync() is declared twice, and the one outside the ifdef
CONFIG_HAS_DMA could lead to a build error when CONFIG_HAS_DMA=n.
As it's an overlooked leftover after rebase, drop this line.
Fixes: a25684a95646 ("ALSA: memalloc: Support for non-contiguous page allocation")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20211019165402.4fa82c38@canb.auug.org.au
Link: https://lore.kernel.org/r/20211019060536.26089-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Checking .non_legacy_dai_naming is not readable.
Let's add new snd_soc_component_is_codec().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h7dft7dn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 5.15-rc6
|
|
We've had an x86-specific SG-buffer handling code, but now it can be
merged gracefully with the standard non-contiguous DMA pages.
After the migration, SNDRV_DMA_TYPE_DMA_SG becomes identical with
SNDRV_DMA_TYPE_NONCONTIG on x86, while others still fall back to
SNDRV_DMA_TYPE_DEV.
The remaining problem is about the SG-buffer with WC pages: the DMA
core stuff on x86 doesn't treat it well, so we still need some special
handling to manipulate the page attribute manually. The mmap handler
for SNDRV_DMA_TYPE_DEV_SG_WC still returns -ENOENT intentionally for
the fallback to the default handler.
Link: https://lore.kernel.org/r/20211017074859.24112-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Following to the addition of non-contiguous pages, this patch adds the
new contiguous non-coherent page allocation to the standard memalloc
helper. Like the previous non-contig type, this non-coherent type is
also directional and requires the explicit sync, too. Hence the
driver using this type of buffer may need to set
SNDRV_PCM_INFO_EXPLICIT_SYNC flag to the PCM hardware.info as well,
unless it's set up in the managed mode.
Link: https://lore.kernel.org/r/20211017074859.24112-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds the support for allocation of non-contiguous DMA pages
in the common memalloc helper. It's another SG-buffer type, but
unlike the existing one, this is directional and requires the explicit
sync / invalidation of dirty pages on non-coherent architectures.
For this enhancement, the following points are changed:
- snd_dma_device stores the DMA direction.
- snd_dma_device stores need_sync flag indicating whether the explicit
sync is required or not.
- A new variant of helper functions, snd_dma_alloc_dir_pages() and
*_all() are introduced; the old snd_dma_alloc_pages() and *_all()
kept as just wrappers with DMA_BIDIRECTIONAL.
- A new helper snd_dma_buffer_sync() is introduced; this gets called
in the appropriate places.
- A new allocation type, SNDRV_DMA_TYPE_NONCONTIG, is introduced.
When the driver allocates pages with this new type, and it may require
the SNDRV_PCM_INFO_EXPLICIT_SYNC flag set to the PCM hardware.info for
taking the full control of PCM applptr and hwptr changes (that implies
disabling the mmap of control/status data). When the buffer
allocation is managed by snd_pcm_set_managed_buffer(), this flag is
automatically set depending on the result of dma_need_sync()
internally. Otherwise, if the buffer is managed manually, the driver
has to set the flag explicitly, too.
The explicit sync between CPU and device for non-coherent memory is
performed at the points before and after read/write transfer as well
as the applptr/hwptr syncptr ioctl. In the case of mmap mode,
user-space is supposed to call the syncptr ioctl with the hwptr flag
to update and fetch the status at first; this corresponds to CPU-sync.
Then user-space advances the applptr via syncptr ioctl again with
applptr flag, and this corresponds to the device sync with flushing.
Other than the DMA direction and the explicit sync, the usage of this
new buffer type is almost equivalent with the existing
SNDRV_DMA_TYPE_DEV_SG; you can get the page and the address via
snd_sgbuf_get_page() and snd_sgbuf_get_addr(), also calculate the
continuous pages via snd_sgbuf_get_chunk_size().
For those SG-page handling, the non-contig type shares the same ops
with the vmalloc handler. As we do always vmap the SG pages at first,
the actual address can be deduced from the vmapped address easily
without iterating the SG-list.
Link: https://lore.kernel.org/r/20211017074859.24112-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds Codec2Codec support to audio-graph-card2.
It can use Codec2Codec but very simple case only for now.
It doesn't have "SWITCH" control yet, thus it start automatically
when it was probed, and can't stop, so far.
Thus it needs to be updated around widgets/routing handling,
and you need to understand that it is under experimental.
Codec has SND_SOC_DAPM_INPUT() (= IN) / SND_SOC_DAPM_OUTPUT(= OUT)
widgets in below case.
It is assuming 2channel, S32_LE format for now.
It needs to be updated, too.
It needs "codec2codec" node (= B), needs to have routing (= A),
need to indicate CPU side at links (= X).
ports@0 is for CPU side (= X), port@1 is Codec side (= Y).
It needs to have "rate" (= C)
+--+
| |<-- Codec0 <-- IN
| |--> Codec1 --> OUT
+--+
sound {
compatible = "audio-graph-card2";
(A) routing = "OUT" ,"DAI1 Playback",
"DAI0 Capture", "IN";
(X) links = <&c2c>;
(B) codec2codec {
ports {
(C) rate = <48000>;
(X) c2c: port@0 { c2cf_ep: endpoint { remote-endpoint = <&codec0_ep>; }; };
(Y) port@1 { c2cb_ep: endpoint { remote-endpoint = <&codec1_ep>; }; };
};
};
Codec {
ports {
port@0 {
bitclock-master;
frame-master;
codec0_ep: endpoint { remote-endpoint = <&c2cf_ep>; }; };
port@1 { codec1_ep: endpoint { remote-endpoint = <&c2cb_ep>; }; };
};
};
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y26ylu4a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds DPCM support to audio-graph-card2.
It uses "dpcm" node (= D), needs to have routing (= A),
need to indicate both FE/BE at links (= B, C).
dpcm ports@0 is for FE (= B), port@1 is for BE (= C).
remote-endpoint can use both Single/Multi connection.
DSP
************
PCM0 <--> * fe0 be0 * <--> DAI0: Codec Headset
PCM1 <--> * fe1 be1 * <--> DAI1: Codec Speakers
PCM2 <--> * fe2 be2 * <--> DAI2: MODEM
PCM3 <--> * fe3 be3 * <--> DAI3: BT
* be4 * <--> DAI4: DMIC
* be5 * <--> DAI5: FM
************
sound {
compatible = "audio-graph-card2";
// indicate routing
(A) routing = "xxx Playback", "xxx Playback",
"xxx Playback", "xxx Playback",
"xxx Playback", "xxx Playback";
// indicate all Front-End, Back-End in DPCM case
(B) links = <&fe0, &fe1, ...
(C) &be0, &be1, ...
(D) dpcm {
// Front-End
ports@0 {
(B) fe0: port@0 { fe0_ep: endpoint { remote-endpoint = <&pcm0_ep>; }; };
(B) fe1: port@1 { fe1_ep: endpoint { remote-endpoint = <&pcm1_ep>; }; };
...
};
// Back-End
ports@1 {
(C) be0: port@0 { be0_ep: endpoint { remote-endpoint = <&dai0_ep>; }; };
(C) be1: port@1 { be1_ep: endpoint { remote-endpoint = <&dai1_ep>; }; };
...
};
};
};
CPU {
ports {
bitclock-master;
frame-master;
port@0 { pcm0_ep: endpoint { remote-endpoint = <&fe0_ep>; }; };
port@1 { pcm1_ep: endpoint { remote-endpoint = <&fe1_ep>; }; };
...
};
};
Codec {
ports {
port@0 { dai0_ep: endpoint { remote-endpoint = <&be0_ep>; }; };
port@1 { dai1_ep: endpoint { remote-endpoint = <&be1_ep>; }; };
...
};
};
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zgrelu4v.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We already have audio-graph-card which is Of-graph base of general
sound card driver.
It is supporting DPCM connection, but was forcibly expanded.
Thus, it is very difficult to add new features on it, for example
Multi CPU/Codec support, Codec2Codec support, etc.
This patch adds more flexible new Audio Graph Card2 driver for it.
audio-graph-card and audio-graph-card2 are similar, but don't have
full compatibility.
Audio Graph Card2 supports very generic connection, but some users
want to have its own settings, for example PLL settings, etc.
For such case, it has customizing support.
In users own driver, it can use Audio Graph Card2 parsing by using
audio_graph2_parse_of(), and doing its own customizing.
Because Audio Graph Card2 is still under experimental stage,
it will indicate such warning when probing, and the DT syntax
might be changed.
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/871r8u4s6q.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87a6mhwyqn.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87tuitusy4.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/87a6jn56x0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735p6n8q1.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
codec2codec needs snd_soc_pcm_stream settings.
This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874k9mn8qy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
