Age | Commit message (Collapse) | Author | Files | Lines |
|
Some audio hardware cannot support the same slot width for all sample
widths, or a slot width equal to the sample width for all sample widths.
This is usually due either to limitations of the audio serial port or
system clocking restrictions.
A typical example would be:
- 16-bit samples in 16-bit slots
- 24-bit samples in 32-bit slots
The new dai-tdm-slot-width-map property allows setting a mapping of
sample widths and the corresponding tdm slot widths and slot counts.
Although the slot count is usually the same for all cases this does
allow for adding padding slots to maintain the same bitclk frequency.
The property is added to each endpoint node that needs the component
DAI to be told the TDM slot width and count.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220228172754.453783-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new system-clock-fixed flag, which can be used to specify that the
driver cannot or should not allow the clock frequency of the mapped clock
to be modified. This behavior is also implied if the system-clock-frequency
parameter is set explicitly - the flag is meant for cases where a clock is
mapped to the DAI but which is, or should be treated as, fixed.
When mclk-fs is also specified, this causes a PCM constraint to be added
which enforces that only the corresponding valid sample rate can be used.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-7-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
codec2codec needs snd_soc_pcm_stream settings.
This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874k9mn8qy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-card2 will support DPCM/Multi/Codec2Codec,
and these will use almost same DT settings which uses
ports0 and ports1.
This patch adds asoc_graph_is_ports0() which checks
port is under port0 or not.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yu2n8ra.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current limit of 128 is not sufficient when more components are
added to the audio map on Tegra210 and later platforms. Thus it is
resulting in probe failure.
The requirement is of nearly ~200 DAI links. To give sufficient room
for future additions the maximum limit is increased to 512 DAI links.
This is a preparatory patch to add more components like resampler,
mixer, multiplexers, demultiplexers and volume controllers to Tegra210
and later platforms.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1631551342-25469-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-card2 can reuse audio_graph_remove() / asoc_simple_remove().
This patch moves it to simple-card-utils.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y2df3uby.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
audio-graph-card2 can reuse audio_graph_card_probe().
This patch moves it to simple-card-utils.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zgxv3uc4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Tegra186 and later, the number of links can go up to 72, so bump the
maximum number of links to the next power of two (128).
Fixes: f2138aed231c ("ASoC: simple-card-utils: enable flexible CPU/Codec/Platform")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210416071147.2149109-2-thierry.reding@gmail.com
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dev is not used. This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87eefgwf8j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We can use 100 char now for 1 line.
This patch tidyup unreadable dev_dbg() message.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87fszwwf8o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
simple-card / audio-graph can use clock as dai->clk or dai->sysclk.
These related information should be indicated at same position.
This patch tidyup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h7kcwf8t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
asoc_simple_canonicalize_cpu/platform()
Current asoc_simple_canonicalize_cpu/platform() is assuming single CPU,
single Platform, but we want to support Multi support.
This patch is prepare for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87im4swf8y.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We shouldn't use dai_props->cpus/codecs/cpu_dai/codec_dai/codec_conf
directly, because these are array to supporting multi CPU/Codec/Platform.
This patch adds asoc_link_to_xxx() macro for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0p8wf9b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now ALSA is supporting multi-CPU/Codec,
thus, we want to know number of CPU/Codec when debugging.
This patch indicates it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lf9owf9g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
link->dai_fmt might be 0.
Don't indicate it in such case when debugging.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mtu4wf9k.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
Now, asoc_simple_parse_xxx() macro is assuming single DAI.
To support multi-CPU/Codec, this patch unpack asoc_simple_parse_xxx()
macro, and uses "&dai_link->cpus[i]" instead of "dai_link->cpus".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmz0wf9u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC is now supporting multi DAI, but, current
simple-card / audio-graph are assuming fixed single DAI.
This patch uses for_each_prop_xxx() to support multi DAI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1jgwf9y.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
li->dais is same as number of CPU + Codec,
li->conf is same as number of Codec when dummy-Codec.
li->dais/li->conf are no longer needed.
This patch removes these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sg3wwfa3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple-card / audio-graph creates 1xCPU + 1xCodec + 1xPlatform
for all dai_link, but some of them is not needed.
For example Platform is not needed for DPCM BE case.
Moreover, we can share snd-soc-dummy DAI for CPU-dummy / dummy-Codec
in DPCM.
This patch adds dummy DAI and share it when DPCM case,
I beliave it can contribute to reduce memory.
By this patch, CPU-dummy / dummy-CPU are set at asoc_simple_init_priv(),
thus, its settings are no longer needed at DPCM detecting timing
on simple-card / audio-graph.
Moreover, we can remove triky Platform settings code for DPCM BE,
because un-needed Platform is not created.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuoqod22.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple-card / audio-graph are assuming fixed
single-CPU/Codec/Platform.
This patch prepares multi-CPU/Codec/Platform support.
Note is that it is not yet full-multi-support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v996od2c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
simple-card / audio-graph are assuming single CPU/Codec/Platform on
dai_link. Because of it, it is difficult to support Multi-CPU/Codec.
This patch allocs CPU/Codec/Platform dai_link imformation
instead of using existing props information. It can update to
multi-CPU/Codec, but is still assuming single-CPU/Codec for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blb61tpv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add new members in struct 'asoc_simple_priv'. Idea is to leverage
simple or graph card driver as much as possible and vendor can
maintain a thin driver to control the behavior by populating these
newly exposed members.
Following are the members added in 'asoc_simple_priv':
- 'ops' struct: In some cases SoC vendor drivers may want to
implement 'snd_soc_ops' callbacks differently. In such cases
custom callbacks would be used.
- 'force_dpcm' flag: Right now simple or graph card drivers
detect DAI links as DPCM links if:
* The dpcm_selectable is set AND
* Codec is connected to multiple CPU endpoints or aconvert
property is used for rate/channels.
So there is no way to directly specify usage of DPCM alone. So a
flag is exposed to mark all links as DPCM. Vendor driver can
set this if required.
- 'dpcm_selectable': Currently simple or audio graph drivers
provide a way to enable this for specific compatibles. However
vendor driver may want to define some additional info. Thus
expose this variable where vendor drivers can set this if
required.
Audio graph driver is updated to consider above flags or callbacks.
Subsequent patches in the series illustrate usage for above.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1604329814-24779-7-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the pin_name is fixed in asoc_simple_init_jack, but some driver
may use a different pin_name. So add a new parameter in
asoc_simple_init_jack for configuring pin_name.
If this parameter is NULL, then the default pin_name is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1594822179-1849-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-5.5
|
|
When debug is enabled compiler cannot find the definition of
clk_get_rate resulting in the following error:
./include/sound/simple_card_utils.h:168:40: note: previous implicit
declaration of ‘clk_get_rate’ was here
dev_dbg(dev, "%s clk %luHz\n", name, clk_get_rate(dai->clk));
./include/sound/simple_card_utils.h:168:3: note: in expansion of macro
‘dev_dbg’
dev_dbg(dev, "%s clk %luHz\n", name, clk_get_rate(dai->clk));
Fix this by including the appropriate header.
Fixes: 0580dde59438686d ("ASoC: simple-card-utils: add asoc_simple_debug_info()")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191009153615.32105-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
asoc_simple_debug_info and asoc_simple_debug_dai must be static
otherwise we might a compilation error if the compiler decides
not to inline the given function.
Fixes: 0580dde59438686d ("ASoC: simple-card-utils: add asoc_simple_debug_info()")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191009153615.32105-3-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
props->xxx_dai might be NULL when DPCM.
This patch cares it for debug.
Fixes: commit 0580dde59438 ("ASoC: simple-card-utils: add asoc_simple_debug_info()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o922gw4u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC supports modern style dai_link (= snd_soc_dai_link_component) for
CPU. legacy style dai_link (= cpu_dai_name, cpu_name, cpu_of_node) are
no longer needed.
This patch switches to modern style.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This function is a helper that permits to create pin switch controls for
a list of widgets whose names are listed in the PREFIX "pin-switches"
devicetree property.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple-card-utils is using asoc_simple_card_xxx() for each
function naming, but it is very verbose.
Thus it is easy to be over 80 char.
This patch renames it to asoc_simple_xxx().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph are using
asoc_simple_card_parse_dai() which is different implementation.
But, these are implemanted at simple-card-utils.
It should be implemanted at each files.
This patch separate these into each files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph are initializing each priv,
but it is same operation.
This patch adds new asoc_simple_card_init_priv() and initialize
priv by same operation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_be_hw_params_fixup() between in these
2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_dai_init() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_hw_param() between in these 2 drivers.
One note is that only simple-card supports simple_set_clk_rate()
at hw_param from commit e9be4ffd4f40fcb ("ASoC: simple-card: set cpu
dai clk in hw_params").
By this patch, audio-graph has same feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_shutdown() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The difference between simple-card / audio-graph are just using
OF graph style, or not. In other words, other things should be same.
This means, simple-card/audio-graph common functions should be
implemented at simple-card-utils, and its own functions should be
implemented at each files.
Current simple-card / audio-graph have almost same functions.
This patch shares asoc_simple_startup() between in these 2 drivers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Historically, simple-card/simple-scu-card/audio-graph/audio-graph-scu
are similar but different generic sound card.
simple-scu-card which was for DPCM was merged into simple-card, and
audio-graph-scu which was for DPCM was merged into audio-graph.
simple-card is for non OF graph sound card, and
audio-graph is for OF graph sound card.
And, small detail difference (= function parameter, naming, etc)
between simple-card/audio-graph has been unified.
So today, the difference between simple-card/audio-graph are
just using OF graph style, or not.
In other words, there should no difference other than OF graph sytle.
simple-card/audio-graph are using own priv today , but we can merge it.
This patch merge it at simple_card_utils.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple-card-utils has dev_dbg(), but people want to
add #define DEBUG at simple-card/audio-graph, not simple-card-utils.
And, people want to get all information.
This patch adds new asoc_simple_debug_info() to indicates information.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple-card is using asoc_simple_card_canonicalize_dailink().
Its naming is "dailink", but is for "platform".
We already have asoc_simple_card_canonicalize_cpu() for "cpu",
let's follow same naming rule.
It never return error, so, void function is better idea.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current snd_soc_dai_link is starting to use snd_soc_dai_link_component
(= modern) style for Platform, but it is still assuming single Platform
so far. We will need to have multi Platform support in the not far
future.
Currently only simple card is using it as sound card driver,
and other drivers are converted to it from legacy style by
snd_soc_init_platform().
To avoid future problem of multi Platform support, let's add
num_platforms before it is too late.
In the same time, to make it same naming mothed, "platform" should
be "platforms". This patch fixup it too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
asoc_simple_card_of_parse_routing()
asoc_simple_card_of_parse_routing() had "option" parameter
to consider error handling, but it is very pointless parameter.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple-card-utils has asoc_simple_card_parse_convert() to parse
convert channel/rate for be_hw_params_fixup.
But, it is parsing from top of node.
If sound card had multi subnode, we need to parse it from each sub node.
This patch tidyup asoc_simple_card_parse_convert() to allow parsing
settings from each node.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC is supporting snd_soc_dai_link_component for binding,
it is more useful than current legacy style.
Currently only codec is supporting it as multicodec (= codecs).
CPU will support multi style in the future.
We want to have it on Platform too in the future.
If all Codec/CPU/Platform are replaced into snd_soc_dai_link_component
style, we can remove legacy complex style.
This patch supports snd_soc_dai_link_component style
for simple-card-util for platform.
[current]
struct snd_soc_dai_link {
...
*cpu_name;
*cpu_of_node;
*cpu_dai_name;
*codec_name;
*codec_of_node;
*codec_dai_name;
*codecs;
num_codecs;
*platform_name;
*platform_of_node;
...
}
[in the future]
struct snd_soc_dai_link {
...
*cpus
num_cpus;
*codecs;
num_codecs;
*platform;
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ASoC is supporting snd_soc_dai_link_component for binding,
it is more useful than current legacy style.
Currently only codec is supporting it as multicodec (= codecs).
CPU will support multi style in the future.
We want to have it on Platform too in the future.
If all Codec/CPU/Platform are replaced into snd_soc_dai_link_component
style, we can remove legacy complex style.
This patch supports snd_soc_dai_link_component style
for simple_card_utils for codec.
[current]
struct snd_soc_dai_link {
...
*cpu_name;
*cpu_of_node;
*cpu_dai_name;
*codec_name;
*codec_of_node;
*codec_dai_name;
*codecs;
num_codecs;
*platform_name;
*platform_of_node;
...
}
[in the future]
struct snd_soc_dai_link {
...
*cpus
num_cpus;
*codecs;
num_codecs;
*platform;
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch moves headphone and microphone jack detection gpios from
simple-card driver. It is preparing for using this feature from other
drivers.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some CPU drivers (e. g. davinci-mcasp) may require the system clock to
be configured as OUT, while there's no good way currently to set
SND_SOC_CLK_OUT in simple-soc driver if the clock is fixed-rate.
This patch makes asoc_simple_card_init_dai() initialize clock to
SND_SOCK_CLK_OUT if explicitly stated in the relevant dts file. This
change is transparent and doesn't change the default behavior.
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple card drivers are parsing widgets on each own driver
(only simple-card at this point, but will be supported on all drivers)
Encapsulation is one of simple card util's purpose.
Let's add asoc_simple_card_of_parse_widgets for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current simple card drivers are parsing routing on each own driver.
Encapsulation is one of simple card util's purpose.
Let's add asoc_simple_card_of_parse_routing for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|