| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We've had scsi-mq for 2.5 years now, so we can remove the unused flag to
disable the code on a per-host basis that was put in for unexpected
emergencies during bringup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
Some host adapters (e.g. Hyper-V storvsc) are known for not respecting
the SPC-2/3/4 requirement for 'INQUIRY data (see table ...) shall
contain at least 36 bytes'. As a result we get tons on 'scsi 0:7:1:1:
scsi scan: INQUIRY result too short (5), using 36' messages on
console. This can be problematic for slow consoles. Introduce
short_inquiry flag in struct Scsi_Host to print the message once per
host.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The libata tag allocation is using a round-robin policy. Next patch will
make libata use block generic tag allocation, so let's add a policy to
tag allocation.
Currently two policies: FIFO (default) and round-robin.
Cc: Jens Axboe <axboe@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree update from Jiri Kosina:
"Usual stuff: documentation updates, printk() fixes, etc"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
intel_ips: fix a type in error message
cpufreq: cpufreq-dt: Move newline to end of error message
ps3rom: fix error return code
treewide: fix typo in printk and Kconfig
ARM: dts: bcm63138: change "interupts" to "interrupts"
Replace mentions of "list_struct" to "list_head"
kernel: trace: fix printk message
scsi: mpt2sas: fix ioctl in comment
zbud, zswap: change module author email
clocksource: Fix 'clcoksource' typo in comment
arm: fix wording of "Crotex" in CONFIG_ARCH_EXYNOS3 help
gpio: msm-v1: make boolean argument more obvious
usb: Fix typo in usb-serial-simple.c
PCI: Fix comment typo 'COMFIG_PM_OPS'
powerpc: Fix comment typo 'CONIFG_8xx'
powerpc: Fix comment typos 'CONFiG_ALTIVEC'
clk: st: Spelling s/stucture/structure/
isci: Spelling s/stucture/structure/
usb: gadget: zero: Spelling s/infrastucture/infrastructure/
treewide: Fix company name in module descriptions
...
|
|
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
|
|
current trivial.git base
|
|
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Allow a SCSI LLD to declare how many hardware queues it supports
by setting Scsi_Host.nr_hw_queues before calling scsi_add_host().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit 1abf635 (scsi: use 64-bit value for 'max_luns') changed the order
of Scsi_Host members. Update the comment to reflect this.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add a use_cmd_list flag in struct Scsi_Host to request keeping track of
all outstanding commands per device.
Default behaviour is not to keep track of cmd_list per sdev, as this may
introduce lock contention. (overhead is more on multi-node NUMA.), and
only enable it on the two drivers that need it.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch adds support for an alternate I/O path in the scsi midlayer
which uses the blk-mq infrastructure instead of the legacy request code.
Use of blk-mq is fully transparent to drivers, although for now a host
template field is provided to opt out of blk-mq usage in case any unforseen
incompatibilities arise.
In general replacing the legacy request code with blk-mq is a simple and
mostly mechanical transformation. The biggest exception is the new code
that deals with the fact the I/O submissions in blk-mq must happen from
process context, which slightly complicates the I/O completion handler.
The second biggest differences is that blk-mq is build around the concept
of preallocated requests that also include driver specific data, which
in SCSI context means the scsi_cmnd structure. This completely avoids
dynamic memory allocations for the fast path through I/O submission.
Due the preallocated requests the MQ code path exclusively uses the
host-wide shared tag allocator instead of a per-LUN one. This only
affects drivers actually using the block layer provided tag allocator
instead of their own. Unlike the old path blk-mq always provides a tag,
although drivers don't have to use it.
For now the blk-mq path is disable by defauly and must be enabled using
the "use_blk_mq" module parameter. Once the remaining work in the block
layer to make blk-mq more suitable for slow devices is complete I hope
to make it the default and eventually even remove the old code path.
Based on the earlier scsi-mq prototype by Nicholas Bellinger.
Thanks to Bart Van Assche and Robert Elliot for testing, benchmarking and
various sugestions and code contributions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
|
|
Seems like these counters are missing any sort of synchronization for
updates, as a over 10 year old comment from me noted. Fix this by
using atomic counters, and while we're at it also make sure they are
in the same cacheline as the _busy counters and not needlessly stored
to in every I/O completion.
With the new model the _busy counters can temporarily go negative,
so all the readers are updated to check for > 0 values. Longer
term every successful I/O completion will reset the counters to zero,
so the temporarily negative values will not cause any harm.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
|
|
Avoid taking the host-wide host_lock to check the per-host queue limit.
Instead we do an atomic_inc_return early on to grab our slot in the queue,
and if necessary decrement it after finishing all checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Now that the ibmvstgt driver as the only user of scsi_tgt is gone, the
scsi_tgt kernel module, the CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and
CONFIG_SCSI_FC_TGT_ATTRS kbuild variable, the scsi_host_template
transfer_response method are no longer needed.
[hch: minor updates to the current tree, changelog update]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
max_sectors in struct Scsi_Host specifies maximum number of sectors
allowed in a single SCSI command. The data type of max_sectors is
unsigned short, so the maximum transfer length per SCSI command is
limited to less than 256MB in 4096-bytes sector size. (0xffff * 4096)
This commit increases the SCSI mid level's limitation for max_sectors
upto the block layer's limitation for max_hw_sectors by extending the
data type of max_sectors in struct Scsi_Host and scsi_host_template,
so that SCSI lower level drivers can specify more than 0xffff.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This allows drivers to specify the size of their per-command private
data in the host template and then get extra memory allocated for
each command instead of needing another allocation in ->queuecommand.
With the current SCSI code that already does multiple allocations for
each command this probably doesn't make a big performance impact, but
it allows to clean up the drivers, and prepare them for using the
blk-mq infrastructure where the common allocation will make a difference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When a command runs into a timeout we need to send an 'ABORT TASK'
TMF. This is typically done by the 'eh_abort_handler' LLDD callback.
Conceptually, however, this function is a normal SCSI command, so
there is no need to enter the error handler.
This patch implements a new scsi_abort_command() function which
invokes an asynchronous function scsi_eh_abort_handler() to
abort the commands via the usual 'eh_abort_handler'.
If abort succeeds the command is either retried or terminated,
depending on the number of allowed retries. However, 'eh_eflags'
records the abort, so if the retry would fail again the
command is pushed onto the error handler without trying to
abort it (again); it'll be cleared up from SCSI EH.
[hare: smatch detected stray switch fixed]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.
This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.
[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patchs adds an 'eh_deadline' sysfs attribute to the scsi
host which limits the overall runtime of the SCSI EH.
The 'eh_deadline' value is stored in the now obsolete field
'resetting'.
When a command is failed the start time of the EH is stored
in 'last_reset'. If the overall runtime of the SCSI EH is longer
than last_reset + eh_deadline, the EH is short-circuited and
falls through to issue a host reset only.
[jejb: add comments in Scsi_Host about new fields]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Field is now unused, so this is dead code.
[jejb: remove resetting and last_reset from Scsi_Host]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
all users converted to ->show_info()/->write_info()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
It's still an obsolete interface; don't introduce those in new drivers.
However, it's saner than the ->proc_info() and commits after this one
will convert the existing ->proc_info() users to it.
The read side is ->show_info(seq_file *, struct Scsi_Host *); use
seq_... for generating contents.
The write side is ->write_info(struct Scsi_Host *, char *, int).
Again, this is driven by procfs needs; we are going to kill ->write_proc()
and ->read_proc() and this is the main obstacle to burying that piece of
shit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The range checking from fe542396 was bad. We would still end up walking
beyond the array as Type 3 is defined to be 4 in the protection
bitmask. Instead use ARRAY_SIZE() for the range check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We set the capacity to zero when we discovered a device formatted with
an unknown DIF protection type. However, the read_capacity code would
override the capacity and cause the device to be enabled regardless.
Make sd_read_protection_type() return an error if the protection type is
unknown. Also prevent duplicate printk lines when the device is being
revalidated.
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
With previous change, now the ata port runtime suspend will happen as:
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend
ata port(parent device) suspend need to schedule scsi EH which will resume
scsi host(child device). Then the child device resume will in turn make
parent device resume first. This is kind of recursive.
This patch adds a new flag Scsi_Host::eh_noresume.
ata port will set this flag to skip the runtime PM calls on scsi host.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The problem is that if we are doing a scsi scan then the device goes
into recovery then we will wait for the recovery to complete. It waits
because scsi-ml will send inquiries or report luns and the queueing code
will have been blocked due to the host not being ready. However, if we
are in recovery and then a scan is started the scan will silently fail
and some devices will not be added.
It is easy to hit the problem where devices do not show up with
FC where we are doing tests that disrupt the target controllers.
When the controller is disruprted (reboot, or setting firmware, etc),
and we cause the dev loss tmo to fire then devices will be removed
Then when the problem has been fixed, the rport will be scanned and
devices should be added back. But if we cause another disruption before
scanning has started then devices will not get added back. If the problem
is not started until the scan is started then the devices will be added
back.
This patch fixes that problem by not failing scans when the host
is in recovery. We will let scsi-ml send the IO and let the queueing
and scsi error handling deal with it like is done if we went into
recovery while scanning.
For recovery cases where the host is being torn down then with the
patch we will still fail the scan since there is not point in scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some controllers have a hardware limit on the number of protection
information scatter-gather list segments they can handle.
Introduce a max_integrity_segments limit in the block layer and provide
a new scsi_host_template setting that allows HBA drivers to provide a
value suitable for the hardware.
Add support for honoring the integrity segment limit when merging both
bios and requests.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
|
|
Implement sd_unlock_native_capacity() method which calls into
hostt->unlock_native_capacity() if implemented. This will be invoked
by block layer if partitions extend beyond the end of the device and
can be used to implement, for example, on-demand ATA host protected
area unlocking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
|
|
Some of our virtual SCSI hosts don't have a proper bus parent at the
top, which can be a problem for doing DMA on them
This patch makes the host device cache a pointer to the physical bus
device and provides an extra API for setting it (the normal API picks
it up from the parent). This patch also modifies the qla2xxx and lpfc
vport logic to use the new DMA host setting API.
Acked-By: James Smart <james.smart@emulex.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The advent of DIF Type 2 devices exposed some missing break statements
in the protection mask switch constructs. However, rewriting the code
to use an index into a small static array seemed like a more elegant
solution.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled. However, communication between initiator and target should be
independent of protection information DMA. There are DIF-only host
adapters coming out that will be able to take advantage of this.
Move the relevant DIF bits to sd.c.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Attached is the ELS/CT pass-thru patch for the FC Transport. The patch
creates a generic framework that lays on top of bsg and the SGIO v4 ioctl
in order to pass transaction requests to LLDD's.
The interface supports the following operations:
On an fc_host basis:
Request login to the specified N_Port_ID, creating an fc_rport.
Request logout of the specified N_Port_ID, deleting an fc_rport
Send ELS request to specified N_Port_ID w/o requiring a login, and
wait for ELS response.
Send CT request to specified N_Port_ID and wait for CT response.
Login is required, but LLDD is allowed to manage login and decide
whether it stays in place after the request is satisfied.
Vendor-Unique request. Allows a LLDD-specific request to be passed
to the LLDD, and the passing of a response back to the application.
On an fc_rport basis:
Send ELS request to nport and wait for ELS response.
Send CT request to nport and wait for CT response.
The patch also exports several headers from include/scsi such that
they can be available to user-space applications:
include/scsi/scsi.h
include/scsi/scsi_netlink.h
include/scsi/scsi_netlink_fc.h
include/scsi/scsi_bsg_fc.h
For further information, refer to the last RFC:
http://marc.info/?l=linux-scsi&m=123436574018579&w=2
Note: Documentation is still spotty and will be added later.
[bharrosh@panasas.com: update for new block API]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
