| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Doug and I are at a conference next week so if another PR is sent I
expect it to only be bug fixes. Parav noted yesterday that there are
some fringe case behavior changes in his work that he would like to
fix, and I see that Intel has a number of rc looking patches for HFI1
they posted yesterday.
Parav is again the biggest contributor by patch count with his ongoing
work to enable container support in the RDMA stack, followed by Leon
doing syzkaller inspired cleanups, though most of the actual fixing
went to RC.
There is one uncomfortable series here fixing the user ABI to actually
work as intended in 32 bit mode. There are lots of notes in the commit
messages, but the basic summary is we don't think there is an actual
32 bit kernel user of drivers/infiniband for several good reasons.
However we are seeing people want to use a 32 bit user space with 64
bit kernel, which didn't completely work today. So in fixing it we
required a 32 bit rxe user to upgrade their userspace. rxe users are
still already quite rare and we think a 32 bit one is non-existing.
- Fix RDMA uapi headers to actually compile in userspace and be more
complete
- Three shared with netdev pull requests from Mellanox:
* 7 patches, mostly to net with 1 IB related one at the back).
This series addresses an IRQ performance issue (patch 1),
cleanups related to the fix for the IRQ performance problem
(patches 2-6), and then extends the fragmented completion queue
support that already exists in the net side of the driver to the
ib side of the driver (patch 7).
* Mostly IB, with 5 patches to net that are needed to support the
remaining 10 patches to the IB subsystem. This series extends
the current 'representor' framework when the mlx5 driver is in
switchdev mode from being a netdev only construct to being a
netdev/IB dev construct. The IB dev is limited to raw Eth queue
pairs only, but by having an IB dev of this type attached to the
representor for a switchdev port, it enables DPDK to work on the
switchdev device.
* All net related, but needed as infrastructure for the rdma
driver
- Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers
- SRP performance updates
- IB uverbs write path cleanup patch series from Leon
- Add RDMA_CM support to ib_srpt. This is disabled by default. Users
need to set the port for ib_srpt to listen on in configfs in order
for it to be enabled
(/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)
- TSO and Scatter FCS support in mlx4
- Refactor of modify_qp routine to resolve problems seen while
working on new code that is forthcoming
- More refactoring and updates of RDMA CM for containers support from
Parav
- mlx5 'fine grained packet pacing', 'ipsec offload' and 'device
memory' user API features
- Infrastructure updates for the new IOCTL interface, based on
increased usage
- ABI compatibility bug fixes to fully support 32 bit userspace on 64
bit kernel as was originally intended. See the commit messages for
extensive details
- Syzkaller bugs and code cleanups motivated by them"
* tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (199 commits)
IB/rxe: Fix for oops in rxe_register_device on ppc64le arch
IB/mlx5: Device memory mr registration support
net/mlx5: Mkey creation command adjustments
IB/mlx5: Device memory support in mlx5_ib
net/mlx5: Query device memory capabilities
IB/uverbs: Add device memory registration ioctl support
IB/uverbs: Add alloc/free dm uverbs ioctl support
IB/uverbs: Add device memory capabilities reporting
IB/uverbs: Expose device memory capabilities to user
RDMA/qedr: Fix wmb usage in qedr
IB/rxe: Removed GID add/del dummy routines
RDMA/qedr: Zero stack memory before copying to user space
IB/mlx5: Add ability to hash by IPSEC_SPI when creating a TIR
IB/mlx5: Add information for querying IPsec capabilities
IB/mlx5: Add IPsec support for egress and ingress
{net,IB}/mlx5: Add ipsec helper
IB/mlx5: Add modify_flow_action_esp verb
IB/mlx5: Add implementation for create and destroy action_xfrm
IB/uverbs: Introduce ESP steering match filter
IB/uverbs: Add modify ESP flow_action
...
|
|
Adding new ioctl method for the MR object - REG_DM_MR.
This command can be used by users to register an allocated
device memory buffer as an MR and receive lkey and rkey
to be used within work requests.
It is added as a new method under the MR object and using a new
ib_device callback - reg_dm_mr.
The command creates a standard ib_mr object which represents the
registered memory.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This change adds uverbs support for allocation/freeing
of device memory commands.
A new uverbs object is defined of type idr to represent
and track the new resource type allocation per context.
The API requires provider driver to implement 2 new ib_device
callbacks - one for allocation and one for deallocation which
return and accept (respectively) the ib_dm object which represents
the allocated memory on the device.
The support is added via the ioctl command infrastructure
only.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This change allows vendors to report device memory capability
max_dm_size - to user via uverbs command.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Adding a new ESP steering match filter that could match against
spi and seq used in IPSec protocol.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
flow_actions of ESP type could be modified during runtime. This could be
common for example when ESN should be changed. Adding a new
UVERBS_FLOW_ACTION_ESP_MODIFY method for changing ESP parameters of an
existing ESP flow_action.
The new method uses the UVERBS_FLOW_ACTION_ESP_CREATE attributes, but
adds a new IB_FLOW_ACTION_ESP_FLAGS_MOD_ESP_ATTRS which means ESP_ATTRS
should be changed.
In addition, we add a new FLOW_ACTION_ESP_REPLAY_NONE replay type that
could be used when one wants to disable a replay protection over a
specific flow_action.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The egress flag indicates that this flow steering rule is for egress
traffic. The scope of an egress rule is port-wide, meaning all packets
originated from that port, which match the steering rule specification
will be effected by this steering rule's action.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Binding a flow_action to flow steering rule requires using a new
specification. Therefore, adding such an IB_FLOW_SPEC_ACTION_HANDLE flow
specification.
Flow steering rules could use flow_action(s) and as of that we need to
avoid deleting flow_action(s) as long as they're being used.
Moreover, when the attached rules are deleted, action_handle reference
count should be decremented. Introducing a new mechanism of flow
resources to keep track on the attached action_handle(s). Later on, this
mechanism should be extended to other attached flow steering resources
like flow counters.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
A verbs application may receive and transmits packets using a data
path pipeline. Sometimes, the first stage in the receive pipeline or
the last stage in the transmit pipeline involves transforming a
packet, either in order to make it easier for later stages to process
it or to prepare it for transmission over the wire. Such transformation
could be stripping/encapsulating the packet (i.e. vxlan),
decrypting/encrypting it (i.e. ipsec), altering headers, doing some
complex FPGA changes, etc.
Some hardware could do such transformations without software data path
intervention at all. The flow steering API supports steering a
packet (either to a QP or dropping it) and some simple packet
immutable actions (i.e. tagging a packet). Complex actions, that may
change the packet, could bloat the flow steering API extensively.
Sometimes the same action should be applied to several flows.
In this case, it's easier to bind several flows to the same action and
modify it than change all matching flows.
Introducing a new flow_action object that abstracts any packet
transformation (out of a standard and well defined set of actions).
This flow_action object could be tied to a flow steering rule via a
new specification.
Currently, we support esp flow_action, which encrypts or decrypts a
packet according to the given parameters. However, we present a
flexible schema that could be used to other transformation actions tied
to flow rules.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Methods sometimes need to get one attribute out of a group of
pre-defined attributes. This is an enum-like behavior. Since
this is a common requirement, we add a new ENUM attribute to the
generic uverbs ioctl() layer. This attribute is embedded in methods,
like any other attributes we currently have. ENUM attributes point to
an array of standard UVERBS_ATTR_PTR_IN. The user-space encodes the
enum's attribute id in the id field and the internal PTR_IN attr id in
the enum_data.elem_id field. This ENUM attribute could be shared by
several attributes and it can get UVERBS_ATTR_SPEC_F_MANDATORY flag,
stating this attribute must be supported by the kernel, like any other
attribute.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Now that ib_gid_attr contains device, port and index, simplify the
provider APIs add_gid() and del_gid() to use device, port and index
fields from the ib_gid_attr attributes structure.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Code is refactored to prepare separate functions for RoCE which can do more
complex operations related to reference counting, while still
maintainining code readability. This includes
(a) Simplification to not perform netdevice checks and modifications
for IB link layer.
(b) Do not add RoCE GID entry which has NULL netdevice; instead return
an error.
(c) If GID addition fails at provider level add_gid(), do not add the
entry in the cache and keep the entry marked as INVALID.
(d) Simplify and reuse the ib_cache_gid_add()/del() routines so that they
can be used even for modifying default GIDs. This avoid some code
duplication in modifying default GIDs.
(e) find_gid() routine refers to the data entry flags to qualify a GID
as valid or invalid GID rather than depending on attributes and zeroness
of the GID content.
(f) gid_table_reserve_default() sets the GID default attribute at
beginning while setting up the GID table. There is no need to use
default_gid flag in low level functions such as write_gid(), add_gid(),
del_gid(), as they never need to update the DEFAULT property of the GID
entry while during GID table update.
As as result of this refactor, reserved GID 0:0:0:0:0:0:0:0 is no longer
searchable as described below.
A unicast GID entry of 0:0:0:0:0:0:0:0 is Reserved GID as per the IB
spec version 1.3 section 4.1.1, point (6) whose snippet is below.
"The unicast GID address 0:0:0:0:0:0:0:0 is reserved - referred to as
the Reserved GID. It shall never be assigned to any endport. It shall
not be used as a destination address or in a global routing header
(GRH)."
GID table cache now only stores valid GID entries. Before this patch,
Reserved GID 0:0:0:0:0:0:0:0 was searchable in the GID table using
ib_find_cached_gid_by_port() and other similar find routines.
Zero GID is no longer searchable as it shall not to be present in GRH or
path recored entry as described in IB spec version 1.3 section 4.1.1,
point (6), section 12.7.10 and section 12.7.20.
ib_cache_update() is simplified to check link layer once, use unified
locking scheme for all link layers, removed temporary gid table
allocation/free logic.
Additionally,
(a) Expand ib_gid_attr to store port and index so that GID query
routines can get port and index information from the attribute structure.
(b) Expand ib_gid_attr to store device as well so that in future code when
GID reference counting is done, device is used to reach back to the GID
table entry.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
query_gid() should return right GID value for iWarp and IB link layers.
It is a no-op for RoCE link layer. Update the documentation to reflect
this.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rdma_cm_state enum is internal to rdma_cm kernel module.
It is not required to expose state enums to ULP modules.
So lets keep its scope limited to rdma_cm module in cma_priv.h file.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Since the rdma_port_space enum is being passed between user and kernel for
user cm_id setup, we need it in a UAPI header. So add it to
rdma_user_cm.h.
This also fixes the cm_id restrack changes which pass up the port space
value via the RDMA_NLDEV_ATTR_RES_PS attribute.
Fixes: 00313983cda6 ("RDMA/nldev: provide detailed CM_ID information")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This is no longer supported, so remove it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
There are several places in the ucma ABI where userspace can pass in a
sockaddr but set the address family to AF_IB. When that happens,
rdma_addr_size() will return a size bigger than sizeof struct sockaddr_in6,
and the ucma kernel code might end up copying past the end of a buffer
not sized for a struct sockaddr_ib.
Fix this by introducing new variants
int rdma_addr_size_in6(struct sockaddr_in6 *addr);
int rdma_addr_size_kss(struct __kernel_sockaddr_storage *addr);
that are type-safe for the types used in the ucma ABI and return 0 if the
size computed is bigger than the size of the type passed in. We can use
these new variants to check what size userspace has passed in before
copying any addresses.
Reported-by: <syzbot+6800425d54ed3ed8135d@syzkaller.appspotmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Currently access to hardware stats buffer isn't protected, this can
result in multiple writes and reads at the same time to the same
memory location. This can lead to providing an incorrect value to
the user. Add a mutex to protect against it.
Fixes: b40f4757daa1 ("IB/core: Make device counter infrastructure dynamic")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Last user is gone after bdf5bd7f2132 "rds: tcp: remove
register_netdevice_notifier infrastructure.", so we can
remove this netdevice command. This allows to delete
rtnl_lock() in netdev_run_todo(), which is hot path for
net namespace unregistration.
dev_change_net_namespace() and netdev_wait_allrefs()
have rcu_barrier() before NETDEV_UNREGISTER_FINAL call,
and the source commits say they were introduced to
delemit the call with NETDEV_UNREGISTER, but this patch
leaves them on the places, since they require additional
analysis, whether we need in them for something else.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently CM request for RoCE follows following flow.
rdma_create_id()
rdma_resolve_addr()
rdma_resolve_route()
For RC QPs:
rdma_connect()
->cma_connect_ib()
->ib_send_cm_req()
->cm_init_av_by_path()
->ib_init_ah_attr_from_path()
For UD QPs:
rdma_connect()
->cma_resolve_ib_udp()
->ib_send_cm_sidr_req()
->cm_init_av_by_path()
->ib_init_ah_attr_from_path()
In both the flows, route is already resolved before sending CM requests.
Therefore, code is refactored to avoid resolving route second time in
ib_cm layer.
ib_init_ah_attr_from_path() is extended to resolve route when it is not
yet resolved for RoCE link layer. This is achieved by caller setting
route_resolved field in path record whenever it has route already
resolved.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The restrack clean routine had simple, but powerful WARN_ON check
to see if all resources are cleared prior to releasing device.
The WARN_ON check performed very well, but lack of information
which device caused to resource leak, the object type and origin
made debug to be fun and challenging at the same time.
The fact that all dumps were the same because restrack_clean() is
called in dealloc() didn't help either.
So let's fix spelling error and convert WARN_ON to be more debug
friendly. The dmesg cut below gives example of how the output
will look output for the case fixed in patch [1]
[ 438.421372] restrack: ------------[ cut here ]------------
[ 438.423448] restrack: BUG: RESTRACK detected leak of resources on mlx5_2
[ 438.425600] restrack: Kernel PD object allocated by mlx5_ib is not freed
[ 438.427753] restrack: Kernel CQ object allocated by mlx5_ib is not freed
[ 438.429660] restrack: ------------[ cut here ]------------
[1] https://patchwork.kernel.org/patch/10298695/
Cc: Michal Kalderon <Michal.Kalderon@cavium.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Previously, adding driver specific attributes required drivers to
declare all the hierarchy - object tree, object, methods and the
attributes themselves. A common use case is adding a few attributes to
an existing common method.
In order to simplify the driver's code, we add some macros to do all
these declarations automatically.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Currently, all objects are declared in uverbs_std_types. This could lead
to a huge file once we implement all objects, methods and handlers.
Moving each object to its own file to keep the files smaller and more
readable. uverbs_std_types.c will only contain the parsing tree
definition and objects without any methods.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The ioctl() based uverbs is based on merging feature trees. This teaches
the generic parser how to parse methods according to the provider's
support. In order to support merging with the common objects, exporting
the common-object-tree to the provider drivers.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Previously, we've used UVERBS_ATTR_SPEC_F_MIN_SZ for extending existing
attributes. The behavior of this flag was the kernel accepts anything
bigger than the minimum size it specified. This is unsafe, since in
order to safely extend an attribute, we need to make sure unknown size
is zeroed. Replacing UVERBS_ATTR_SPEC_F_MIN_SZ with
UVERBS_ATTR_SPEC_F_MIN_SZ_OR_ZERO, which essentially checks that the
unknown size is zero. In addition, attributes are now decorated with
UVERBS_ATTR_TYPE and UVERBS_ATTR_STRUCT, so we can provide the minimum
and known length.
Users of this flag needs to use copy_from_or_zero functions/macros.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Downstream patches extend uverbs_attr_spec with new fields.
In order to save space, we move the type and flags fields to
the various attribute flavors contained in the union.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Extending uverbs_ioctl header with driver_id and another reserved
field. driver_id should be used in order to identify the driver.
Since every driver could have its own parsing tree, this is necessary
for strace support.
Downstream patches take off the EXPERIMENTAL flag from the ioctl() IB
support and thus we add some reserved fields for future usage.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Use macros to make names consistent in ioctl() uAPI:
The ioctl() uAPI works with object-method hierarchy. The method part
also states which handler should be executed when this method is called
from user-space. Therefore, we need to tie method, method's id, method's
handler and the object owning this method together.
Previously, this was done through explicit developer chosen names.
This makes grepping the code harder. Changing the method's name,
method's handler and object's name to be automatically generated based
on the ids.
The headers are split in a way so they be included and used by
user-space. One header strictly contains structures that are used
directly by user-space applications, where another header is used for
internal library (i.e. libibverbs) to form the ioctl() commands.
Other header simply contains the required general command structure.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
XRCD object is not implemented in the restrack, so lets remove it.
Fixes: 02d8883f520e ("RDMA/restrack: Add general infrastructure to track RDMA resources")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ib_peek_cq() verb doesn't seem be implemented in current code.
There is some past reference to it at [1] about it being unimplemented.
Lot of user documentation created out of kdoc refers to this
unimplemented API. Therefore, remove unimplemented API.
[1] http://lists.openfabrics.org/pipermail/ofw/2008-May/002465.html
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Before commit [1], rdma_addr_find_l2_eth_by_grh() was an exported function
and therefore declaration in include/rdma/ib_addr.h was fine.
But now that its scope is limited to ib_core module, its better to have it
in core_priv.h.
[1] commit 1060f8653414 ("IB/{core/cm}: Fix generating a return AH for
RoCEE")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Resolving route for RoCE for a path record is needed only for the
received CM requests.
Therefore,
(a) ib_init_ah_attr_from_path() is refactored first to isolate the
code of resolving route.
(b) Setting dlid, path bits is not needed for RoCE.
Additionally ah attribute initialization is done from the path record
entry, so it is better to refer to path record entry type for
different link layer instead of ah attribute type while initializing
ah attribute itself.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
rdma_resolve_ip_route() is used only by ib_core module. Therefore it is
removed as an exported symbol.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ib_find_gid() is only used by IPoIB driver. For IB link layer, GID table
entries are not based on netdevice. Netdevice parameter is unused here.
Therefore, it is removed.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Exported symbol's comments should be with function definition and not in
the header file. Therefore comments of ib_find_cached_gid() and
ib_find_cached_gid_by_port() functions are moved closer to their
definitions.
The function name in then comment is different than the actual function
name, fix it to be same as ib_cache_gid_find_by_filter().
Also current comment section of ib_find_cached_gid_by_port() contains the
desciption of ib_find_cached_gid(), fix that as well.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
All callers to ib_modify_qp_is_ok() provides enum ib_qp_state
makes the checks of out-of-scope redundant. Let's remove them
together with updating function signature to return boolean result.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Implement the RDMA nldev netlink interface for dumping detailed
MR information.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Implement RDMA nldev netlink interface to get detailed CM_ID information.
Because cm_id's are attached to rdma devices in various work queue
contexts, the pid and task information at restrak_add() time is sometimes
not useful. For example, an nvme/f host connection cm_id ends up being
bound to a device in a work queue context and the resulting pid at attach
time no longer exists after connection setup. So instead we mark all
cm_id's created via the rdma_ucm as "user", and all others as "kernel".
This required tweaking the restrack code a little. It also required
wrapping some rdma_cm functions to allow passing the module name string.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The union approach will get the endianness wrong sometimes if the kernel's
pointer size is 32 bits resulting in EFAULTs when trying to copy to/from
user.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This fixes several bugs around the copy_to/from user path:
- copy_to used the user provided size of the attribute
and could copy data beyond the end of the kernel buffer into
userspace.
- copy_from didn't know the size of the kernel buffer and
could have left kernel memory unexpectedly un-initialized.
- copy_from did not use the user length to determine if the
attribute data is inlined or not.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Resource tracking of XRCD objects is not implemented in current
version of restrack and hence can be removed.
Fixes: 02d8883f520e ("RDMA/restrack: Add general infrastructure to track RDMA resources")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
iWarp devices do not support the creation of address handles
so return AH_ATTR_TYPE_UNDEFINED for all iWarp devices.
While we are here reduce the size of port_num to u8 and add
a comment.
Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Reported-by: Parav Pandit <parav@mellanox.com>
CC: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
packet->fecn and packet->becn are calculated in the hot path
and are never used. Remove these fields as they show to be
costly in a profile. Also, remove initialization for
becn and fecn in process_ecn() as they're unconditionally
assigned in the function and ensure fecn and becn variables
use a boolean type.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The packet type comparison used to find out if a packet is a bypass
packet in the hot path is an expensive operation as seen in a profile.
Determine packet's pkey and migration bit through the bypass and 9B
code paths instead.
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
In hfi1_rc_rcv(), BTH is computed for all packets received.
However, it's only used for packets received with opcodes
RDMA_WRITE_LAST and SEND_LAST, and it is a costly operation.
Compute BTH only in the RDMA_WRITE_LAST/SEND_LAST code path
and let the compiler handle endianness conversion for bitwise
operations.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The RDMA subsystem has very strict set of objects to work with, but it
completely lacks tracking facilities and has no visibility of resource
utilization.
The following patch adds such infrastructure to keep track of RDMA
resources to help with debugging of user space applications. The primary
user of this infrastructure is RDMA nldev netlink (following patches), to
be exposed to userspace via rdmatool, but it is not limited too that.
At this stage, the main three objects (PD, CQ and QP) are added, and more
will be added later.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The KBUILD_MODNAME variable contains the module name and it is known for
kernel users during compilation, so let's reuse it to track the owners.
Followup patches will store this for resource tracking.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Each of our modules only allocates a PD in one place, so there isn't any
loss in detail, while MODNAME is more useful and recognizable as something
to expose to the user.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The flags field the enum is used with comes directly from the uapi
so it belongs in the uapi headers for clarity and so userspace can
use it.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
