Age | Commit message (Collapse) | Author | Files | Lines |
|
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
|
|
Move memcg_socket_limit_enabled decrement to tcp_destroy_cgroup (called
from memcg_destroy_kmem -> mem_cgroup_sockets_destroy) and zap a bunch of
wrapper functions.
Although this patch moves static keys decrement from __mem_cgroup_free to
mem_cgroup_css_free, it does not introduce any functional changes, because
the keys are incremented on setting the limit (tcp or kmem), which can
only happen after successful mem_cgroup_css_online.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security layer updates from James Morris:
"Highlights:
- Smack adds secmark support for Netfilter
- /proc/keys is now mandatory if CONFIG_KEYS=y
- TPM gets its own device class
- Added TPM 2.0 support
- Smack file hook rework (all Smack users should review this!)"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (64 commits)
cipso: don't use IPCB() to locate the CIPSO IP option
SELinux: fix error code in policydb_init()
selinux: add security in-core xattr support for pstore and debugfs
selinux: quiet the filesystem labeling behavior message
selinux: Remove unused function avc_sidcmp()
ima: /proc/keys is now mandatory
Smack: Repair netfilter dependency
X.509: silence asn1 compiler debug output
X.509: shut up about included cert for silent build
KEYS: Make /proc/keys unconditional if CONFIG_KEYS=y
MAINTAINERS: email update
tpm/tpm_tis: Add missing ifdef CONFIG_ACPI for pnp_acpi_device
smack: fix possible use after frees in task_security() callers
smack: Add missing logging in bidirectional UDS connect check
Smack: secmark support for netfilter
Smack: Rework file hooks
tpm: fix format string error in tpm-chip.c
char/tpm/tpm_crb: fix build error
smack: Fix a bidirectional UDS connect check typo
smack: introduce a special case for tmpfs in smack_d_instantiate()
...
|
|
Change remote checksum handling to set checksum partial as default
behavior. Added an iflink parameter to configure not using
checksum partial (calling csum_partial to update checksum).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remote checksum offload processing is currently the same for both
the GRO and non-GRO path. When the remote checksum offload option
is encountered, the checksum field referred to is modified in
the packet. So in the GRO case, the packet is modified in the
GRO path and then the operation is skipped when the packet goes
through the normal path based on skb->remcsum_offload. There is
a problem in that the packet may be modified in the GRO path, but
then forwarded off host still containing the remote checksum option.
A remote host will again perform RCO but now the checksum verification
will fail since GRO RCO already modified the checksum.
To fix this, we ensure that GRO restores a packet to it's original
state before returning. In this model, when GRO processes a remote
checksum option it still changes the checksum per the algorithm
but on return from lower layer processing the checksum is restored
to its original value.
In this patch we add define gro_remcsum structure which is passed
to skb_gro_remcsum_process to save offset and delta for the checksum
being changed. After lower layer processing, skb_gro_remcsum_cleanup
is called to restore the checksum before returning from GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the IPCB() macro to get the IPv4 options is convenient, but
unfortunately NetLabel often needs to examine the CIPSO option outside
of the scope of the IP layer in the stack. While historically IPCB()
worked above the IP layer, due to the inclusion of the inet_skb_param
struct at the head of the {tcp,udp}_skb_cb structs, recent commit
971f10ec ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
reordered the tcp_skb_cb struct and invalidated this IPCB() trick.
This patch fixes the problem by creating a new function,
cipso_v4_optptr(), which locates the CIPSO option inside the IP header
without calling IPCB(). Unfortunately, this isn't as fast as a simple
lookup so some additional tweaks were made to limit the use of this
new function.
Cc: <stable@vger.kernel.org> # 3.18
Reported-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
|
|
Packetization Layer Path MTU Discovery works separately beside
Path MTU Discovery at IP level, different net namespace has
various requirements on which one to chose, e.g., a virutalized
container instance would require TCP PMTU to probe an usable
effective mtu for underlying tunnel, while the host would
employ classical ICMP based PMTU to function.
Hence making TCP PMTU mechanism per net namespace to decouple
two functionality. Furthermore the probe base MSS should also
be configured separately for each namespace.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make __ipv6_select_ident() static as it isn't used outside
the file.
Fixes: 0508c07f5e0c9 (ipv6: Select fragment id during UFO segmentation if not set.)
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When queuing work to send the NETDEV_BONDING_INFO netdev event, it's
possible that when the work is executed, the pointer to the slave
becomes invalid. This can happen if between queuing the event and the
execution of the work, the net-device was un-ensvaled and re-enslaved.
Fix that by queuing a work with the data of the slave instead of the
slave structure.
Fixes: 69e6113343cf ('net/bonding: Notify state change on slaves')
Reported-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Receive Flow Steering is a nice solution but suffers from
hash collisions when a mix of connected and unconnected traffic
is received on the host, when flow hash table is populated.
Also, clearing flow in inet_release() makes RFS not very good
for short lived flows, as many packets can follow close().
(FIN , ACK packets, ...)
This patch extends the information stored into global hash table
to not only include cpu number, but upper part of the hash value.
I use a 32bit value, and dynamically split it in two parts.
For host with less than 64 possible cpus, this gives 6 bits for the
cpu number, and 26 (32-6) bits for the upper part of the hash.
Since hash bucket selection use low order bits of the hash, we have
a full hash match, if /proc/sys/net/core/rps_sock_flow_entries is big
enough.
If the hash found in flow table does not match, we fallback to RPS (if
it is enabled for the rxqueue).
This means that a packet for an non connected flow can avoid the
IPI through a unrelated/victim CPU.
This also means we no longer have to clear the table at socket
close time, and this helps short lived flows performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the SYN_RECV state, where the TCP connection is represented by
tcp_request_sock, we now rate-limit SYNACKs in response to a client's
retransmitted SYNs: we do not send a SYNACK in response to client SYN
if it has been less than sysctl_tcp_invalid_ratelimit (default 500ms)
since we last sent a SYNACK in response to a client's retransmitted
SYN.
This allows the vast majority of legitimate client connections to
proceed unimpeded, even for the most aggressive platforms, iOS and
MacOS, which actually retransmit SYNs 1-second intervals for several
times in a row. They use SYN RTO timeouts following the progression:
1,1,1,1,1,2,4,8,16,32.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Helpers for mitigating ACK loops by rate-limiting dupacks sent in
response to incoming out-of-window packets.
This patch includes:
- rate-limiting logic
- sysctl to control how often we allow dupacks to out-of-window packets
- SNMP counter for cases where we rate-limited our dupack sending
The rate-limiting logic in this patch decides to not send dupacks in
response to out-of-window segments if (a) they are SYNs or pure ACKs
and (b) the remote endpoint is sending them faster than the configured
rate limit.
We rate-limit our responses rather than blocking them entirely or
resetting the connection, because legitimate connections can rely on
dupacks in response to some out-of-window segments. For example, zero
window probes are typically sent with a sequence number that is below
the current window, and ZWPs thus expect to thus elicit a dupack in
response.
We allow dupacks in response to TCP segments with data, because these
may be spurious retransmissions for which the remote endpoint wants to
receive DSACKs. This is safe because segments with data can't
realistically be part of ACK loops, which by their nature consist of
each side sending pure/data-less ACKs to each other.
The dupack interval is controlled by a new sysctl knob,
tcp_invalid_ratelimit, given in milliseconds, in case an administrator
needs to dial this upward in the face of a high-rate DoS attack. The
name and units are chosen to be analogous to the existing analogous
knob for ICMP, icmp_ratelimit.
The default value for tcp_invalid_ratelimit is 500ms, which allows at
most one such dupack per 500ms. This is chosen to be 2x faster than
the 1-second minimum RTO interval allowed by RFC 6298 (section 2, rule
2.4). We allow the extra 2x factor because network delay variations
can cause packets sent at 1 second intervals to be compressed and
arrive much closer.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 second pull request
This is the second NFC pull request for 3.20.
It brings:
- NCI NFCEE (NFC Execution Environment, typically an embedded or
external secure element) discovery and enabling/disabling support.
In order to communicate with an NFCEE, we also added NCI's logical
connections support to the NCI stack.
- HCI over NCI protocol support. Some secure elements only understand
HCI and thus we need to send them HCI frames when they're part of
an NCI chipset.
- NFC_EVT_TRANSACTION userspace API addition. Whenever an application
running on a secure element needs to notify its host counterpart,
we send an NFC_EVENT_SE_TRANSACTION event to userspace through the
NFC netlink socket.
- Secure element and HCI transaction event support for the st21nfcb
chipset.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 4429 ("Optimistic DAD") states that optimistic addresses
should be treated as deprecated addresses. From section 2.1:
Unless noted otherwise, components of the IPv6 protocol stack
should treat addresses in the Optimistic state equivalently to
those in the Deprecated state, indicating that the address is
available for use but should not be used if another suitable
address is available.
Optimistic addresses are indeed avoided when other addresses are
available (i.e. at source address selection time), but they have
not heretofore been available for things like explicit bind() and
sendmsg() with struct in6_pktinfo, etc.
This change makes optimistic addresses treated more like
deprecated addresses than tentative ones.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
include/net/ipv6.h:713:22: warning: incorrect type in assignment (different base types)
include/net/ipv6.h:713:22: expected restricted __be32 [usertype] hash
include/net/ipv6.h:713:22: got unsigned int
include/net/ipv6.h:719:25: warning: restricted __be32 degrades to integer
include/net/ipv6.h:719:22: warning: invalid assignment: ^=
include/net/ipv6.h:719:22: left side has type restricted __be32
include/net/ipv6.h:719:22: right side has type unsigned int
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(struct flow_keys)->n_proto is in network order, use
proper type for this.
Fixes following sparse errors :
net/core/flow_dissector.c:139:39: warning: incorrect type in assignment (different base types)
net/core/flow_dissector.c:139:39: expected unsigned short [unsigned] [usertype] n_proto
net/core/flow_dissector.c:139:39: got restricted __be16 [assigned] [usertype] proto
net/core/flow_dissector.c:237:23: warning: incorrect type in assignment (different base types)
net/core/flow_dissector.c:237:23: expected unsigned short [unsigned] [usertype] n_proto
net/core/flow_dissector.c:237:23: got restricted __be16 [assigned] [usertype] proto
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: e0f31d849867 ("flow_keys: Record IP layer protocol in skb_flow_dissect()")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
More iov_iter work from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we added pacing to TCP, we decided to let sch_fq take care
of actual pacing.
All TCP had to do was to compute sk->pacing_rate using simple formula:
sk->pacing_rate = 2 * cwnd * mss / rtt
It works well for senders (bulk flows), but not very well for receivers
or even RPC :
cwnd on the receiver can be less than 10, rtt can be around 100ms, so we
can end up pacing ACK packets, slowing down the sender.
Really, only the sender should pace, according to its own logic.
Instead of adding a new bit in skb, or call yet another flow
dissection, we tweak skb->truesize to a small value (2), and
we instruct sch_fq to use new helper and not pace pure ack.
Note this also helps TCP small queue, as ack packets present
in qdisc/NIC do not prevent sending a data packet (RPC workload)
This helps to reduce tx completion overhead, ack packets can use regular
sock_wfree() instead of tcp_wfree() which is a bit more expensive.
This has no impact in the case packets are sent to loopback interface,
as we do not coalesce ack packets (were we would detect skb->truesize
lie)
In case netem (with a delay) is used, skb_orphan_partial() also sets
skb->truesize to 1.
This patch is a combination of two patches we used for about one year at
Google.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use notifier chain to dispatch an event upon a change in slave state.
Event is dispatched with slave specific info.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move slave state changes to a helper function, this is a pre-step for adding
functionality of dispatching an event when this helper is called.
This commit doesn't add new functionality.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-02-03
Here's what's likely the last bluetooth-next pull request for 3.20.
Notable changes include:
- xHCI workaround + a new id for the ath3k driver
- Several new ids for the btusb driver
- Support for new Intel Bluetooth controllers
- Minor cleanups to ieee802154 code
- Nested sleep warning fix in socket accept() code path
- Fixes for Out of Band pairing handling
- Support for LE scan restarting for HCI_QUIRK_STRICT_DUPLICATE_FILTER
- Improvements to data we expose through debugfs
- Proper handling of Hardware Error HCI events
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
For consistency sake change nci_core_conn_create_rsp structure
credits field to credits_cnt.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The NCI_STATIC_RF_CONN_ID logical connection is the most used
connection. Keeping it directly accessible in the nci_dev
structure will simplify and optimize the access.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
If the IPv6 fragment id has not been set and we perform
fragmentation due to UFO, select a new fragment id.
We now consider a fragment id of 0 as unset and if id selection
process returns 0 (after all the pertrubations), we set it to
0x80000000, thus giving us ample space not to create collisions
with the next packet we may have to fragment.
When doing UFO integrity checking, we also select the
fragment id if it has not be set yet. This is stored into
the skb_shinfo() thus allowing UFO to function correclty.
This patch also removes duplicate fragment id generation code
and moves ipv6_select_ident() into the header as it may be
used during GSO.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That takes care of the majority of ->sendmsg() instances - most of them
via memcpy_to_msg() or assorted getfrag() callbacks. One place where we
still keep memcpy_fromiovecend() is tipc - there we potentially read the
same data over and over; separate patch, that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
patch is actually smaller than it seems to be - most of it is unindenting
the inner loop body in tcp_sendmsg() itself...
the bit in tcp_input.c is going to get reverted very soon - that's what
memcpy_from_msg() will become, but not in this commit; let's keep it
reasonably contained...
There's one potentially subtle change here: in case of short copy from
userland, mainline tcp_send_syn_data() discards the skb it has allocated
and falls back to normal path, where we'll send as much as possible after
rereading the same data again. This patch trims SYN+data skb instead -
that way we don't need to copy from the same place twice.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... instead of storing its ->mgs_iter.iov there
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Validate hooks for nf_tables NAT expressions, otherwise users can
crash the kernel when using them from the wrong hook. We already
got one user trapped on this when configuring masquerading.
2) Fix a BUG splat in nf_tables with CONFIG_DEBUG_PREEMPT=y. Reported
by Andreas Schultz.
3) Avoid unnecessary reroute of traffic in the local input path
in IPVS that triggers a crash in in xfrm. Reported by Florian
Wiessner and fixes by Julian Anastasov.
4) Fix memory and module refcount leak from the error path of
nf_tables_newchain().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit is very similar to
commit 1c32c5ad6fac8cee1a77449f5abf211e911ff830
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:47 2011 +0000
inet: Add ip_make_skb and ip_finish_skb
It adds IPv6 version of the helpers ip6_make_skb and ip6_finish_skb.
The job of ip6_make_skb is to collect messages into an ipv6 packet
and poplulate ipv6 eader. The job of ip6_finish_skb is to transmit
the generated skb. Together they replicated the job of
ip6_push_pending_frames() while also provide the capability to be
called independently. This will be needed to add lockless UDP sendmsg
support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx timestamps are looped onto the error queue on top of an skb. This
mechanism leaks packet headers to processes unless the no-payload
options SOF_TIMESTAMPING_OPT_TSONLY is set.
Add a sysctl that optionally drops looped timestamp with data. This
only affects processes without CAP_NET_RAW.
The policy is checked when timestamps are generated in the stack.
It is possible for timestamps with data to be reported after the
sysctl is set, if these were queued internally earlier.
No vulnerability is immediately known that exploits knowledge
gleaned from packet headers, but it may still be preferable to allow
administrators to lock down this path at the cost of possible
breakage of legacy applications.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
(v1 -> v2)
- test socket CAP_NET_RAW instead of capable(CAP_NET_RAW)
(rfc -> v1)
- document the sysctl in Documentation/sysctl/net.txt
- fix access control race: read .._OPT_TSONLY only once,
use same value for permission check and skb generation.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFC_EVT_TRANSACTION is sent through netlink in order for a
specific application running on a secure element to notify
userspace of an event. Typically the secure element application
counterpart on the host could interpret that event and act
upon it.
Forwarded information contains:
- SE host generating the event
- Application IDentifier doing the operation
- Applications parameters
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add NFCEE NCI constant for:
- NFCEE Interface/Protocols
- Destination type
- Destination-specific parameters type
- NFCEE Discovery Action
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This extended return parameters struct conflicts with the new Read Local
OOB Extended Data command definition. To avoid the conflict simply
rename the old "extended" version to the normal one and update the code
appropriately to take into account the two possible response PDU sizes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When using LE_SCAN_FILTER_DUP_ENABLE, some controllers would send
advertising report from each LE device only once. That means that we
don't get any updates on RSSI value, and makes Service Discovery very
slow. This patch adds restarting scan when in Service Discovery, and
device with filtered uuid is found, but it's not in RSSI range to send
event yet. This way if device moves into range, we will quickly get RSSI
update.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Currently there is no way to restart le scan, and it's needed in
service scan method. The way it work: it disable, and then enable le
scan on controller.
During the restart, we must remember when the scan was started, and
it's duration, to later re-schedule the le_scan_disable work, that was
stopped during the stop scan phase.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds two new api's netdev_switch_port_bridge_setlink
and netdev_switch_port_bridge_dellink to offload bridge port attributes
to switch port
(The names of the apis look odd with 'switch_port_bridge',
but am more inclined to change the prefix of the api to something else.
Will take any suggestions).
The api's look at the NETIF_F_HW_SWITCH_OFFLOAD feature flag to
pass bridge port attributes to the port device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit be9f4a44e7d41 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :
commit 3a7c384ffd57e ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.
commit 0980e56e506b ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.
commit b5ec8eeac46 ("ipv4: fix ip_send_skb()") fixed another regression.
commit 811230cd85 ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.
Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.
This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Doing the following commands on a non idle network device
panics the box instantly, because cpu_bstats gets overwritten
by stats.
tc qdisc add dev eth0 root <your_favorite_qdisc>
... some traffic (one packet is enough) ...
tc qdisc replace dev eth0 root est 1sec 4sec <your_favorite_qdisc>
[ 325.355596] BUG: unable to handle kernel paging request at ffff8841dc5a074c
[ 325.362609] IP: [<ffffffff81541c9e>] __gnet_stats_copy_basic+0x3e/0x90
[ 325.369158] PGD 1fa7067 PUD 0
[ 325.372254] Oops: 0000 [#1] SMP
[ 325.375514] Modules linked in: ...
[ 325.398346] CPU: 13 PID: 14313 Comm: tc Not tainted 3.19.0-smp-DEV #1163
[ 325.412042] task: ffff8800793ab5d0 ti: ffff881ff2fa4000 task.ti: ffff881ff2fa4000
[ 325.419518] RIP: 0010:[<ffffffff81541c9e>] [<ffffffff81541c9e>] __gnet_stats_copy_basic+0x3e/0x90
[ 325.428506] RSP: 0018:ffff881ff2fa7928 EFLAGS: 00010286
[ 325.433824] RAX: 000000000000000c RBX: ffff881ff2fa796c RCX: 000000000000000c
[ 325.440988] RDX: ffff8841dc5a0744 RSI: 0000000000000060 RDI: 0000000000000060
[ 325.448120] RBP: ffff881ff2fa7948 R08: ffffffff81cd4f80 R09: 0000000000000000
[ 325.455268] R10: ffff883ff223e400 R11: 0000000000000000 R12: 000000015cba0744
[ 325.462405] R13: ffffffff81cd4f80 R14: ffff883ff223e460 R15: ffff883feea0722c
[ 325.469536] FS: 00007f2ee30fa700(0000) GS:ffff88407fa20000(0000) knlGS:0000000000000000
[ 325.477630] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 325.483380] CR2: ffff8841dc5a074c CR3: 0000003feeae9000 CR4: 00000000001407e0
[ 325.490510] Stack:
[ 325.492524] ffff883feea0722c ffff883fef719dc0 ffff883feea0722c ffff883ff223e4a0
[ 325.499990] ffff881ff2fa79a8 ffffffff815424ee ffff883ff223e49c 000000015cba0744
[ 325.507460] 00000000f2fa7978 0000000000000000 ffff881ff2fa79a8 ffff883ff223e4a0
[ 325.514956] Call Trace:
[ 325.517412] [<ffffffff815424ee>] gen_new_estimator+0x8e/0x230
[ 325.523250] [<ffffffff815427aa>] gen_replace_estimator+0x4a/0x60
[ 325.529349] [<ffffffff815718ab>] tc_modify_qdisc+0x52b/0x590
[ 325.535117] [<ffffffff8155edd0>] rtnetlink_rcv_msg+0xa0/0x240
[ 325.540963] [<ffffffff8155ed30>] ? __rtnl_unlock+0x20/0x20
[ 325.546532] [<ffffffff8157f811>] netlink_rcv_skb+0xb1/0xc0
[ 325.552145] [<ffffffff8155b355>] rtnetlink_rcv+0x25/0x40
[ 325.557558] [<ffffffff8157f0d8>] netlink_unicast+0x168/0x220
[ 325.563317] [<ffffffff8157f47c>] netlink_sendmsg+0x2ec/0x3e0
Lets play safe and not use an union : percpu 'pointers' are mostly read
anyway, and we have typically few qdiscs per host.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 22e0f8b9322c ("net: sched: make bstats per cpu and estimator RCU safe")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of nr_cpu_ids and use modern percpu allocation.
Note that the sockets themselves are not yet allocated
using NUMA affinity.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|