| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The asm-generic/gpio.h header uses the might_sleep() macro but doesn't
include the header for it, so any source code that might include
linux/gpio.h before linux/kernel.h can easily lead to a build failure.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The old RW_DATA_SECTION had INIT_TASK_DATA (which was
more-than-PAGE_SIZE-aligned), followed by a bunch of small alignment
stuff, followed by more PAGE_SIZE-aligned stuff, so you wasted memory
in the middle of .data re-aligning back up to PAGE_SIZE.
This patch sorts the sections by alignment requirements, which should
pack them essentially optimally.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6
* 'hwpoison' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6: (21 commits)
HWPOISON: Enable error_remove_page on btrfs
HWPOISON: Add simple debugfs interface to inject hwpoison on arbitary PFNs
HWPOISON: Add madvise() based injector for hardware poisoned pages v4
HWPOISON: Enable error_remove_page for NFS
HWPOISON: Enable .remove_error_page for migration aware file systems
HWPOISON: The high level memory error handler in the VM v7
HWPOISON: Add PR_MCE_KILL prctl to control early kill behaviour per process
HWPOISON: shmem: call set_page_dirty() with locked page
HWPOISON: Define a new error_remove_page address space op for async truncation
HWPOISON: Add invalidate_inode_page
HWPOISON: Refactor truncate to allow direct truncating of page v2
HWPOISON: check and isolate corrupted free pages v2
HWPOISON: Handle hardware poisoned pages in try_to_unmap
HWPOISON: Use bitmask/action code for try_to_unmap behaviour
HWPOISON: x86: Add VM_FAULT_HWPOISON handling to x86 page fault handler v2
HWPOISON: Add poison check to page fault handling
HWPOISON: Add basic support for poisoned pages in fault handler v3
HWPOISON: Add new SIGBUS error codes for hardware poison signals
HWPOISON: Add support for poison swap entries v2
HWPOISON: Export some rmap vma locking to outside world
...
|
|
In order to direct the SIGIO signal to a particular thread of a
multi-threaded application we cannot, like suggested by the manpage, put a
TID into the regular fcntl(F_SETOWN) call. It will still be send to the
whole process of which that thread is part.
Since people do want to properly direct SIGIO we introduce F_SETOWN_EX.
The need to direct SIGIO comes from self-monitoring profiling such as with
perf-counters. Perf-counters uses SIGIO to notify that new sample data is
available. If the signal is delivered to the same task that generated the
new sample it can augment that data by inspecting the task's user-space
state right after it returns from the kernel. This is esp. convenient
for interpreted or virtual machine driven environments.
Both F_SETOWN_EX and F_GETOWN_EX take a pointer to a struct f_owner_ex
as argument:
struct f_owner_ex {
int type;
pid_t pid;
};
Where type is one of F_OWNER_TID, F_OWNER_PID or F_OWNER_GID.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: stephane eranian <eranian@googlemail.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
itimers: Add tracepoints for itimer
hrtimer: Add tracepoint for hrtimers
timers: Add tracepoints for timer_list timers
cputime: Optimize jiffies_to_cputime(1)
itimers: Simplify arm_timer() code a bit
itimers: Fix periodic tics precision
itimers: Merge ITIMER_VIRT and ITIMER_PROF
Trivial header file include conflicts in kernel/fork.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland
* 'x86/orig_ax' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
x86: ptrace: set TS_COMPAT when 32-bit ptrace sets orig_eax>=0
x86: ptrace: do not sign-extend orig_ax on write
x86: syscall_get_nr returns int
asm-generic: syscall_get_nr returns int
|
|
Commit 926b663ce8215ba448960e1ff6e58b67a2c3b99b (gpiolib: allow GPIOs to
be named) already provides naming on the chip level. This patch provides
more flexibility by allowing multiple names where ever in sysfs on a per
GPIO basis.
Adapted from David Brownell's comments on a similar concept:
http://lkml.org/lkml/2009/4/20/203.
[randy.dunlap@oracle.com: fix build for CONFIG_GENERIC_GPIO=n]
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some ports (like the Blackfin arch) have a discontiguous memory map which
means there may be text or data that falls outside of the standard range
of the start/end text/data symbols. Creating some helper functions allows
these non-standard ports to declare these regions without adversely
affecting anyone else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robin Getz <rgetz@blackfin.uclinux.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I tend to use a 'D' debugging macro a lot during debugging. When I define
it before includes I often get conflicts with kmap_types.h's use of 'D'
too. It's not very nice when a global include pollutes the name space
like this.
Rename the kmap_types.h D to KMAP_D. It is only used temporarily in the
header so has no effect on anything else.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Only 32 bits of system call number are meaningful, so make the
specification for syscall_get_nr() be to return int, not long.
Signed-off-by: Roland McGrath <roland@redhat.com>
|
|
Add a flag for mmap that will be used to request a huge page region that
will look like anonymous memory to user space. This is accomplished by
using a file on the internal vfsmount. MAP_HUGETLB is a modifier of
MAP_ANONYMOUS and so must be specified with it. The region will behave
the same as a MAP_ANONYMOUS region using small pages.
The patch also adds the MAP_STACK flag, which was previously defined only
on some architectures but not on others. Since MAP_STACK is meant to be a
hint only, architectures can define it without assigning a specific
meaning to it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric B Munson <ebmunson@us.ibm.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: David Rientjes <rientjes@google.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The out-of-tree KSM used ioctls on fds cloned from /dev/ksm to register a
memory area for merging: we prefer now to use an madvise(2) interface.
This patch just defines MADV_MERGEABLE (to tell KSM it may merge pages in
this area found identical to pages in other mergeable areas) and
MADV_UNMERGEABLE (to undo that).
Most architectures use asm-generic, but alpha, mips, parisc, xtensa need
their own definitions: included here for mmotm convenience, but we'll
probably want to split this and feed pieces to arch maintainers.
Based upon earlier patches by Chris Wright and Izik Eidus.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Pick up kernel/softirq.c update for dependent fix.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
|
|
Impact: optional, useful for debugging
Add a new madvice sub command to inject poison for some
pages in a process' address space. This is useful for
testing the poison page handling.
This patch can allow root to tie up large amounts of memory.
I got feedback from container developers and they didn't see any
problem.
v2: Use write flag for get_user_pages to make sure to always get
a fresh page
v3: Don't request write mapping (Fengguang Wu)
v4: Move MADV_* number to avoid conflict with KSM (Hugh Dickins)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
Add new SIGBUS codes for reporting machine checks as signals. When
the hardware detects an uncorrected ECC error it can trigger these
signals.
This is needed for telling KVM's qemu about machine checks that happen to
guests, so that it can inject them, but might be also useful for other programs.
I find it useful in my test programs.
This patch merely defines the new types.
- Define two new si_codes for SIGBUS. BUS_MCEERR_AO and BUS_MCEERR_AR
* BUS_MCEERR_AO is for "Action Optional" machine checks, which means that some
corruption has been detected in the background, but nothing has been consumed
so far. The program can ignore those if it wants (but most programs would
already get killed)
* BUS_MCEERR_AR is for "Action Required" machine checks. This happens
when corrupted data is consumed or the application ran into an area
which has been known to be corrupted earlier. These require immediate
action and cannot just returned to. Most programs would kill themselves.
- They report the address of the corruption in the user address space
in si_addr.
- Define a new si_addr_lsb field that reports the extent of the corruption
to user space. That's currently always a (small) page. The user application
cannot tell where in this page the corruption happened.
AK: I plan to write a man page update before anyone asks.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (23 commits)
at_hdmac: Rework suspend_late()/resume_early()
PM: Reset transition_started at dpm_resume_noirq
PM: Update kerneldoc comments in drivers/base/power/main.c
PM: Add convenience macro to make switching to dev_pm_ops less error-prone
hp-wmi: Switch driver to dev_pm_ops
floppy: Switch driver to dev_pm_ops
PM: Trivial fixes
PM / Hibernate / Memory hotplug: Always use for_each_populated_zone()
PM/Hibernate: Do not try to allocate too much memory too hard (rev. 2)
PM/Hibernate: Do not release preallocated memory unnecessarily (rev. 2)
PM/Hibernate: Rework shrinking of memory
PM: Fix typo in label name s/Platofrm_finish/Platform_finish/
PM: Run-time PM platform device bus support
PM: Introduce core framework for run-time PM of I/O devices (rev. 17)
Driver Core: Make PM operations a const pointer
PM: Remove platform device suspend_late()/resume_early() V2
USB: Rework musb suspend()/resume_early()
I2C: Rework i2c-s3c2410 suspend_late()/resume() V2
I2C: Rework i2c-pxa suspend_late()/resume_early()
DMA: Rework txx9dmac suspend_late()/resume_early()
...
Fix trivial conflict in drivers/base/platform.c (due to same
constification patch being merged in both sides, along with some other
PM work in the PM branch)
|
|
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
MAINTAINERS: update KVM entry
KVM: correct error-handling code
KVM: fix compile warnings on s390
KVM: VMX: Check cpl before emulating debug register access
KVM: fix misreporting of coalesced interrupts by kvm tracer
KVM: x86: drop duplicate kvm_flush_remote_tlb calls
KVM: VMX: call vmx_load_host_state() only if msr is cached
KVM: VMX: Conditionally reload debug register 6
KVM: Use thread debug register storage instead of kvm specific data
KVM guest: do not batch pte updates from interrupt context
KVM: Fix coalesced interrupt reporting in IOAPIC
KVM guest: fix bogus wallclock physical address calculation
KVM: VMX: Fix cr8 exiting control clobbering by EPT
KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
KVM: Document KVM_CAP_IRQCHIP
KVM: Protect update_cr8_intercept() when running without an apic
KVM: VMX: Fix EPT with WP bit change during paging
KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
KVM: x86 emulator: Add adc and sbb missing decoder flags
KVM: Add missing #include
...
|
|
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/i386: Put aligned stack-canary in percpu shared_aligned section
x86/i386: Make sure stack-protector segment base is cache aligned
x86: Detect stack protector for i386 builds on x86_64
x86: allow "=rm" in native_save_fl()
x86: properly annotate alternatives.c
x86: Introduce GDT_ENTRY_INIT(), initialize bad_bios_desc statically
x86, 32-bit: Use generic sys_pipe()
x86: Introduce GDT_ENTRY_INIT(), fix APM
x86: Introduce GDT_ENTRY_INIT()
x86: Introduce set_desc_base() and set_desc_limit()
x86: Remove unused patch_espfix_desc()
x86: Use get_desc_base()
|
|
__start_mcount_loc[] is unused after init, yet occupies RAM forever
as part of .rodata. 152kiB is typical on a 64-bit architecture. Instead,
__start_mcount_loc should be in the interval [__init_begin, __init_end)
so that the space is reclaimed after init.
__start_mcount_loc[] is generated during the load portion
of kernel build, and is used only by ftrace_init(). ftrace_init is declared
'__init' and is in .init.text, which is freed after init.
__start_mcount_loc is placed into .rodata by a call to MCOUNT_REC inside
the RO_DATA macro of include/asm-generic/vmlinux.lds.h. The array *is*
read-only, but more importantly it is not used after init. So the call to
MCOUNT_REC should be moved from RO_DATA to INIT_DATA.
This patch has been tested on x86_64 with CONFIG_DEBUG_PAGEALLOC=y
which verifies that the address range never is accessed after init.
Signed-off-by: John Reiser <jreiser@BitWagon.com>
LKML-Reference: <4A6DF0B6.7080402@bitwagon.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
kvm_para.h contains userspace interface and so
should be exported.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Pack aligned things together into a special section to minimize
padding holes.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Tejun Heo <tj@kernel.org>
LKML-Reference: <4AA035C0.9070202@goop.org>
[ queued up in tip:x86/asm because it depends on this commit:
x86/i386: Make sure stack-protector segment base is cache aligned ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
arch/microblaze/include/asm/socket.h
|
|
This moves flush_write_buffers() in
asm-generic/dma-mapping-common.h to
arch/x86/kernel/pci-nommu.c.
The purpose of this patch is that, we can avoid defining NULL
flush_write_buffers() on IA64 and SPARC.
dma-mapping-common.h is used by X86 and IA64 (and SPARC soon)
but only X86 with CONFIG_X86_OOSTORE or CONFIG_X86_PPRO_FENCE
actually uses flush_write_buffers(). CONFIG_X86_OOSTORE or
CONFIG_X86_PPRO_FENCE is usable with only kernel/pci-nommu.c
(that is, not usable with other X86 IOMMU implementations such
as SWIOTLB, VT-d, etc) so we can safely move
flush_write_buffers() in asm-generic/dma-mapping-common.h to
arch/x86/kernel/pci-nommu.c.
The further discussion is:
http://lkml.org/lkml/2009/6/28/104
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: davem@davemloft.net
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1249872797-1314-2-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This sockopt goes in line with SO_TYPE and SO_PROTOCOL. It makes it
possible for userspace programs to pass around file descriptors — I
am referring to arguments-to-functions, but it may even work for the
fd passing over UNIX sockets — without needing to also pass the
auxiliary information (PF_INET6/IPPROTO_TCP).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to SO_TYPE returning the socket type, SO_PROTOCOL allows to
retrieve the protocol used with a given socket.
I am not quite sure why we have that-many copies of socket.h, and why
the values are not the same on all arches either, but for where hex
numbers dominate, I use 0x1029 for SO_PROTOCOL as that seems to be
the next free unused number across a bunch of operating systems, or
so Google results make me want to believe. SO_PROTOCOL for others
just uses the next free Linux number, 38.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For powerpc with CONFIG_VIRT_CPU_ACCOUNTING
jiffies_to_cputime(1) is not compile time constant and run time
calculations are quite expensive. To optimize we use
precomputed value. For all other architectures is is
preprocessor definition.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <1248862529-6063-5-git-send-email-sgruszka@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow architecture specific data in struct platform_device V3.
With this patch struct pdev_archdata is added to struct
platform_device, similar to struct dev_archdata in found in
struct device. Useful for architecture code that needs to
keep extra data associated with each platform device.
Struct pdev_archdata is different from dev.platform_data, the
convention is that dev.platform_data points to driver-specific
data. It may or may not be required by the driver. The format
of this depends on driver but is the same across architectures.
The structure pdev_archdata is a place for architecture specific
data. This data is handled by architecture specific code (for
example runtime PM), and since it is architecture specific it
should _never_ be touched by device driver code. Exactly like
struct dev_archdata but for platform devices.
[rjw: This change is for power management mostly and that's why it
goes through the suspend tree.]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The BSS section macros in vmlinux.lds.h currently place the .sbss
input section outside the bounds of [__bss_start, __bss_end]. On all
architectures except for microblaze that handle both .sbss and
__bss_start/__bss_end, this is wrong: the .sbss input section is
within the range [__bss_start, __bss_end]. Relatedly, the example
code at the top of the file actually has __bss_start/__bss_end defined
twice; I believe the right fix here is to define them in the
BSS_SECTION macro but not in the BSS macro.
Another problem with the current macros is that several
architectures have an ALIGN(4) or some other small number just before
__bss_stop in their linker scripts. The BSS_SECTION macro currently
hardcodes this to 4; while it should really be an argument. It also
ignores its sbss_align argument; fix that.
mn10300 is the only user at present of any of the macros touched by
this patch. It looks like mn10300 actually was incorrectly converted
to use the new BSS() macro (the alignment of 4 prior to conversion was
a __bss_stop alignment, but the argument to the BSS macro is a start
alignment). So fix this as well.
I'd like acks from Sam and David on this one. Also CCing Paul, since
he has a patch from me which will need to be updated to use
BSS_SECTION(0, PAGE_SIZE, 4) once this gets merged.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
Discarded sections in different archs share some commonality but have
considerable differences. This led to linker script for each arch
implementing its own /DISCARD/ definition, which makes maintaining
tedious and adding new entries error-prone.
This patch makes all linker scripts to move discard definitions to the
end of the linker script and use the common DISCARDS macro. As ld
uses the first matching section definition, archs can include default
discarded sections by including them earlier in the linker script.
ia64 is notable because it first throws away some ia64 specific
subsections and then include the rest of the sections into the final
image, so those sections must be discarded before the inclusion.
defconfig compile tested for x86, x86-64, powerpc, powerpc64, ia64,
alpha, sparc, sparc64 and s390. Michal Simek tested microblaze.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: linux-arch@vger.kernel.org
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Tony Luck <tony.luck@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
|
|
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
|
|
alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation. This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference. This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.
This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration. Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.
This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules. This
also fixes the PER_CPU_ATTRIBUTES double definition bug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: maximilian attems <max@stro.at>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The ctors section for each object file is eight byte aligned (on 64 bit).
However the __ctors_start symbol starts at an arbitrary address dependent
on the size of the previous sections.
Therefore the linker may add some zeroes after __ctors_start to make sure
the ctors contents are properly aligned. However the extra zeroes at the
beginning aren't expected by the code. When walking the functions
pointers contained in there and extra zeroes are added this may result in
random jumps. So make sure that the __ctors_start symbol is always
aligned as well.
Fixes this crash on an allyesconfig on s390:
[ 0.582482] Kernel BUG at 0000000000000012 [verbose debug info unavailable]
[ 0.582489] illegal operation: 0001 [#1] SMP DEBUG_PAGEALLOC
[ 0.582496] Modules linked in:
[ 0.582501] CPU: 0 Tainted: G W 2.6.31-rc1-dirty #273
[ 0.582506] Process swapper (pid: 1, task: 000000003f218000, ksp: 000000003f2238e8)
[ 0.582510] Krnl PSW : 0704200180000000 0000000000000012 (0x12)
[ 0.582518] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
[ 0.582524] Krnl GPRS: 0000000000036727 0000000000000010 0000000000000001 0000000000000001
[ 0.582529] 00000000001dfefa 0000000000000000 0000000000000000 0000000000000040
[ 0.582534] 0000000001fff0f0 0000000001790628 0000000002296048 0000000002296048
[ 0.582540] 00000000020c438e 0000000001786000 0000000002014a66 000000003f223e60
[ 0.582553] Krnl Code:>0000000000000012: 0000 unknown
[ 0.582559] 0000000000000014: 0000 unknown
[ 0.582564] 0000000000000016: 0000 unknown
[ 0.582570] 0000000000000018: 0000 unknown
[ 0.582575] 000000000000001a: 0000 unknown
[ 0.582580] 000000000000001c: 0000 unknown
[ 0.582585] 000000000000001e: 0000 unknown
[ 0.582591] 0000000000000020: 0000 unknown
[ 0.582596] Call Trace:
[ 0.582599] ([<0000000002014a46>] kernel_init+0x622/0x7a0)
[ 0.582607] [<0000000000113e22>] kernel_thread_starter+0x6/0xc
[ 0.582615] [<0000000000113e1c>] kernel_thread_starter+0x0/0xc
[ 0.582621] INFO: lockdep is turned off.
[ 0.582624] Last Breaking-Event-Address:
[ 0.582627] [<0000000002014a64>] kernel_init+0x640/0x7a0
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We recently added a INIT_TASK(align) in include/asm-generic/vmlinux.lds.h,
but there is already a macro INIT_TASK in include/linux/init_task.h, which
is quite confusing. We should switch the macro in the linker script to
INIT_TASK_DATA. (Sorry that I missed this in reviewing the patch). Since
the macros are new, there is only one user of the INIT_TASK in
vmlinux.lds.h, arch/mn10300/kernel/vmlinux.lds.S.
However, we are currently using INIT_TASK_DATA for laying down an entire
.data.init_task section. So rename that to INIT_TASK_DATA_SECTION.
I would be worried about changing the meaning of INIT_TASK_DATA, but the
old INIT_TASK_DATA implementation had no users, and in fact if anyone had
tried to use it, it would have failed to compile because it didn't pass
the alignment to the old INIT_TASK.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
RW_DATA_SECTION is defined to take 4 different alignment parameters,
while NOSAVE_DATA currently uses a fixed PAGE_SIZE alignment as noted
in the comments.
There are presently no in-tree users of this at present, and I just
stumbled across this while implementing the simplified script on a new
architecture port, which subsequently resulted in a syntax error.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
x86 throws away .discard section but no other archs do. Also,
.discard is not thrown away while linking modules. Make every arch
and module linking throw it away. This will be used to define dummy
variables for percpu declarations and definitions.
This patch is based on Ivan Kokshaysky's alpha percpu patch.
[ Impact: always throw away everything in .discard ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: add dummy pgprot_noncached()
lib/checksum.c: fix endianess bug
asm-generic: hook up new system calls
asm-generic: list Arnd as asm-generic maintainer
asm-generic: drop HARDIRQ_BITS definition from hardirq.h
asm-generic: uaccess: fix up local access_ok() usage
asm-generic: uaccess: add missing access_ok() check to strnlen_user()
|
|
Most architectures now provide a pgprot_noncached(), the
remaining ones can simply use an dummy default implementation,
except for cris and xtensa, which should override the
default appropriately.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Magnus Damm <magnus.damm@gmail.com>
|
|
In asm-generic/vmlinux.lds.h, name INIT_RAM_FS consistently, no matter the
setting of CONFIG_BLK_DEV_INITRD. This corrects:
commit ef53dae8658cf0e93d380983824a661067948d87
Author: Sam Ravnborg <sam@ravnborg.org>
Date: Sun Jun 7 20:46:37 2009 +0200
Subject: Improve vmlinux.lds.h support for arch specific linker scripts
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
|
