| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds Makefile and Kconfig for f2fs, and updates Makefile and Kconfig files
in the fs directory.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This moves all of the f2fs debugging files into debugfs. The files are
located in /sys/kernel/debug/f2fs/
Note, I think we are generating all of the same information in each of
the files for every unique f2fs filesystem in the machine. This copies
the functionality that was present in the proc files, but this should be
fixed up in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[jaegeuk.kim@samsung.com: merged 3 debugfs entries into a *status* entry]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds roll-forward routines to recover fsynced data.
- F2FS uses basically roll-back model with checkpointing.
- In order to implement fsync(), there are two approaches as follows.
1. A roll-back model with checkpointing at every fsync()
: This is a naive method, but suffers from very low performance.
2. A roll-forward model
: F2FS adopts this model where all the fsynced data should be recovered, which
were written after checkpointing was done. In order to figure out the data,
F2FS keeps a "fsync" mark in direct node blocks. In addition, F2FS remains
the location of next node block in each direct node block for reconstructing
the chain of node blocks during the recovery.
- In order to enhance the performance, F2FS keeps a "dentry" mark also in direct
node blocks. If this is set during the recovery, F2FS replays adding a dentry.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds on-demand and background cleaning functions.
- The basic background cleaning policy is trying to do cleaning jobs as much as
possible whenever the system is idle. Once the background cleaning is done,
the cleaner sleeps an amount of time not to interfere with VFS calls. The time
is dynamically adjusted according to the status of whole segments, which is
decreased when the following conditions are satisfied.
. GC is not conducted currently, and
. IO subsystem is idle by checking the number of requets in bdev's request
list, and
. There are enough dirty segments.
Otherwise, the time is increased incrementally until to the maximum time.
Note that, min and max times are 10 secs and 30 secs by default.
- F2FS adopts a default victim selection policy where background cleaning uses
a cost-benefit algorithm, while on-demand cleaning uses a greedy algorithm.
- The method of moving data during the cleaning is slightly different between
background and on-demand cleaning schemes. In the case of background cleaning,
F2FS loads the data, and marks them as dirty. Then, F2FS expects that the data
will be moved by flusher or VM. In the case of on-demand cleaning, F2FS should
move the data right away.
- In order to identify valid blocks in a victim segment, F2FS scans the bitmap
of the segment managed as an SIT entry.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This implements xattr and acl functionalities.
- F2FS uses a node page to contain use extended attributes.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
this adds core functions to find, add, delete, and link dentries.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds inode operations for directory, symlink, and special inodes.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds core functions to get, read, write, and evict an inode.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds address space operations for data.
- F2FS supports readpages(), writepages(), and direct_IO().
- Because of out-of-place writes, f2fs_direct_IO() does not write data in place.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds memory operations and file/file_inode operations.
- F2FS supports fallocate(), mmap(), fsync(), and basic ioctl().
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds specific functions not only to manage dirty/free segments, SIT pages,
a cache for SIT entries, and summary entries, but also to allocate free blocks
and write three types of pages: data, node, and meta.
- F2FS maintains three types of bitmaps in memory, which indicate free, prefree,
and dirty segments respectively.
- The key information of an SIT entry consists of a segment number, the number
of valid blocks in the segment, a bitmap to identify there-in valid or invalid
blocks.
- An SIT page is composed of a certain range of SIT entries, which is maintained
by the address space of meta_inode.
- To cache SIT entries, a simple array is used. The index for the array is the
segment number.
- A summary entry for data contains the parent node information. A summary entry
for node contains its node offset from the inode.
- F2FS manages information about six active logs and those summary entries in
memory. Whenever one of them is changed, its summary entries are flushed to
its SIT page maintained by the address space of meta_inode.
- This patch adds a default block allocation function which supports heap-based
allocation policy.
- This patch adds core functions to write data, node, and meta pages. Since LFS
basically produces a series of sequential writes, F2FS merges sequential bios
with a single one as much as possible to reduce the IO scheduling overhead.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds specific functions to manage NAT pages, a cache for NAT entries, free
nids, direct/indirect node blocks for indexing data, and address space for node
pages.
- The key information of an NAT entry consists of a node id and a block address.
- An NAT page is composed of block addresses covered by a certain range of NAT
entries, which is maintained by the address space of meta_inode.
- A radix tree structure is used to cache NAT entries. The index for the tree
is a node id.
- When there is no free nid, F2FS should scan NAT entries to find new one. In
order to avoid scanning frequently, F2FS manages a list containing a number of
free nids in memory. Only when free nids in the list are exhausted, scanning
process, build_free_nids(), is triggered.
- F2FS has direct and indirect node blocks for indexing data. This patch adds
fuctions related to the node block management such as getting, allocating, and
truncating node blocks to index data.
- In order to cache node blocks in memory, F2FS has a node_inode with an address
space for node pages. This patch also adds the address space operations for
node_inode.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds functions required by the checkpoint operations.
Basically, f2fs adopts a roll-back model with checkpoint blocks written in the
CP area. The checkpoint procedure includes as follows.
- write_checkpoint()
1. block_operations() freezes VFS calls.
2. submit cached bios.
3. flush_nat_entries() writes NAT pages updated by dirty NAT entries.
4. flush_sit_entries() writes SIT pages updated by dirty SIT entries.
5. do_checkpoint() writes,
- checkpoint block (#0)
- orphan inode blocks
- summary blocks made by active logs
- checkpoint block (copy of #0)
6. unblock_opeations()
In order to provide an address space for meta pages, f2fs_sb_info has a special
inode, namely meta_inode. This patch also adds the address space operations for
meta_inode.
Signed-off-by: Chul Lee <chur.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds the implementation of superblock operations for f2fs, which includes
- init_f2fs_fs/exit_f2fs_fs
- f2fs_mount
- super_operations of f2fs
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
This adds the following major in-memory structures in f2fs.
- f2fs_sb_info:
contains f2fs-specific information, two special inode pointers for node and
meta address spaces, and orphan inode management.
- f2fs_inode_info:
contains vfs_inode and other fs-specific information.
- f2fs_nm_info:
contains node manager information such as NAT entry cache, free nid list,
and NAT page management.
- f2fs_node_info:
represents a node as node id, inode number, block address, and its version.
- f2fs_sm_info:
contains segment manager information such as SIT entry cache, free segment
map, current active logs, dirty segment management, and segment utilization.
The specific structures are sit_info, free_segmap_info, dirty_seglist_info,
curseg_info.
In addition, add F2FS_SUPER_MAGIC in magic.h.
Signed-off-by: Chul Lee <chur.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
|
|
The direct-IO write path already had the i_size checks in mm/filemap.c,
but it turns out the read path did not, and removing the block size
checks in fs/block_dev.c (commit bbec0270bdd8: "blkdev_max_block: make
private to fs/buffer.c") removed the magic "shrink IO to past the end of
the device" code there.
Fix it by truncating the IO to the size of the block device, like the
write path already does.
NOTE! I suspect the write path would be *much* better off doing it this
way in fs/block_dev.c, rather than hidden deep in mm/filemap.c. The
mm/filemap.c code is extremely hard to follow, and has various
conditionals on the target being a block device (ie the flag passed in
to 'generic_write_checks()', along with a conditional update of the
inode timestamp etc).
It is also quite possible that we should treat this whole block device
size as a "s_maxbytes" issue, and try to make the logic even more
generic. However, in the meantime this is the fairly minimal targeted
fix.
Noted by Milan Broz thanks to a regression test for the cryptsetup
reencrypt tool.
Reported-and-tested-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
READ is zero so the "rw & READ" test is always false. The intended test
was "((rw & RW_MASK) == READ)".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The block device access simplification that avoided accessing the (racy)
block size information (commit bbec0270bdd8: "blkdev_max_block: make
private to fs/buffer.c") no longer checks the maximum block size in the
block mapping path.
That was _almost_ as simple as just removing the code entirely, because
the readers and writers all check the size of the device anyway, so
under normal circumstances it "just worked".
However, the block size may be such that the end of the device may
straddle one single buffer_head. At which point we may still want to
access the end of the device, but the buffer we use to access it
partially extends past the end.
The 'bd_set_size()' function intentionally sets the block size to avoid
this, but mounting the device - or setting the block size by hand to
some other value - can modify that block size.
So instead, teach 'submit_bh()' about the special case of the buffer
head straddling the end of the device, and turning such an access into a
smaller IO access, avoiding the problem.
This, btw, also means that unlike before, we can now access the whole
device regardless of device block size setting. So now, even if the
device size is only 512-byte aligned, we can read and write even the
last sector even when having a much bigger block size for accessing the
rest of the device.
So with this, we could now get rid of the 'bd_set_size()' block size
code entirely - resulting in faster IO for the common case - but that
would be a separate patch.
Reported-and-tested-by: Romain Francoise <romain@orebokech.com>
Reporeted-and-tested-by: Meelis Roos <mroos@linux.ee>
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge 'block-dev' branch.
I was going to just mark everything here for stable and leave it to the
3.8 merge window, but having decided on doing another -rc, I migth as
well merge it now.
This removes the bd_block_size_semaphore semaphore that was added in
this release to fix a race condition between block size changes and
block IO, and replaces it with atomicity guaratees in fs/buffer.c
instead, along with simplifying fs/block-dev.c.
This removes more lines than it adds, makes the code generally simpler,
and avoids the latency/rt issues that the block size semaphore
introduced for mount.
I'm not happy with the timing, but it wouldn't be much better doing this
during the merge window and then having some delayed back-port of it
into stable.
* block-dev:
blkdev_max_block: make private to fs/buffer.c
direct-io: don't read inode->i_blkbits multiple times
blockdev: remove bd_block_size_semaphore again
fs/buffer.c: make block-size be per-page and protected by the page lock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A bunch of fixes; the last one is this cycle regression, the rest are
-stable fodder."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix off-by-one in argument passed by iterate_fd() to callbacks
lookup_one_len: don't accept . and ..
cifs: get rid of blind d_drop() in readdir
nfs_lookup_revalidate(): fix a leak
don't do blind d_drop() in nfs_prime_dcache()
|
|
Pull CIFS fixes from Steve French:
"Two low risk, small fixes, that fix cifs regressions introduced in
3.7."
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix wrong buffer pointer usage in smb_set_file_info
cifs: fix writeback race with file that is growing
|
|
Noticed by Pavel Roskin; the thing in his patch I disagree with
was compensating for that shite in callbacks instead of fixing
it once in the iterator itself.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
We are leaking fattr and fhandle if we decide that dentry is not to
be invalidated, after all (e.g. happens to be a mountpoint). Just
free both before that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
We really don't want to look at the block size for the raw block device
accesses in fs/block-dev.c, because it may be changing from under us.
So get rid of the max_block logic entirely, since the caller should
already have done it anyway.
That leaves the only user of this function in fs/buffer.c, so move the
whole function there and make it static.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since directio can work on a raw block device, and the block size of the
device can change under it, we need to do the same thing that
fs/buffer.c now does: read the block size a single time, using
ACCESS_ONCE().
Reading it multiple times can get different results, which will then
confuse the code because it actually encodes the i_blksize in
relationship to the underlying logical blocksize.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts the block-device direct access code to the previous
unlocked code, now that fs/buffer.c no longer needs external locking.
With this, fs/block_dev.c is back to the original version, apart from a
whitespace cleanup that I didn't want to revert.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This makes the buffer size handling be a per-page thing, which allows us
to not have to worry about locking too much when changing the buffer
size. If a page doesn't have buffers, we still need to read the block
size from the inode, but we can do that with ACCESS_ONCE(), so that even
if the size is changing, we get a consistent value.
This doesn't convert all functions - many of the buffer functions are
used purely by filesystems, which in turn results in the buffer size
being fixed at mount-time. So they don't have the same consistency
issues that the raw device access can have.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 6bdf6dbd662176c0da5c3ac8ed10ac94e7776c85 caused a regression
in setattr codepath that leads to files with wrong attributes.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Commit eddb079deb4 created a regression in the writepages codepath.
Previously, whenever it needed to check the size of the file, it did so
by consulting the inode->i_size field directly. With that patch, the
i_size was fetched once on entry into the writepages code and that value
was used henceforth.
If the file is changing size though (for instance, if someone is writing
to it or has truncated it), then that value is likely to be wrong. This
can lead to data corruption. Pages past the EOF at the time that the
writepages call was issued may be silently dropped and ignored because
cifs_writepages wrongly assumes that the file must have been truncated
in the interim.
Fix cifs_writepages to properly fetch the size from the inode->i_size
field instead to properly account for this possibility.
Original bug report is here:
https://bugzilla.kernel.org/show_bug.cgi?id=50991
Reported-and-Tested-by: Maxim Britov <ungifted01@gmail.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Merge misc fixes from Andrew Morton:
"8 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (8 patches)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext3 regression fix from Jan Kara:
"Fix an ext3 regression introduced during 3.7 merge window. It leads
to deadlock if you stress the filesystem in the right way (luckily
only if blocksize < pagesize)."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
jbd: Fix lock ordering bug in journal_unmap_buffer()
|
|
Commit 169ebd90131b ("writeback: Avoid iput() from flusher thread")
removed iget-iput pair from inode writeback. As a side effect, inodes
that are dirty during iput_final() call won't be ever added to inode LRU
(iput_final() doesn't add dirty inodes to LRU and later when the inode
is cleaned there's noone to add the inode there). Thus inodes are
effectively unreclaimable until someone looks them up again.
The practical effect of this bug is limited by the fact that inodes are
pinned by a dentry for long enough that the inode gets cleaned. But
still the bug can have nasty consequences leading up to OOM conditions
under certain circumstances. Following can easily reproduce the
problem:
for (( i = 0; i < 1000; i++ )); do
mkdir $i
for (( j = 0; j < 1000; j++ )); do
touch $i/$j
echo 2 > /proc/sys/vm/drop_caches
done
done
then one needs to run 'sync; ls -lR' to make inodes reclaimable again.
We fix the issue by inserting unused clean inodes into the LRU after
writeback finishes in inode_sync_complete().
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 7b540d0646ce ("proc_map_files_readdir(): don't bother with
grabbing files") switched proc_map_files_readdir() to use @f_mode
directly instead of grabbing @file reference, but same time the test for
@vm_file presence was lost leading to nil dereference. The patch brings
the test back.
The all proc_map_files feature is CONFIG_CHECKPOINT_RESTORE wrapped
(which is set to 'n' by default) so the bug doesn't affect regular
kernels.
The regression is 3.7-rc1 only as far as I can tell.
[gorcunov@openvz.org: provided changelog]
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull MTD fixes from David Woodhouse:
"The most important part of this is that it fixes a regression in
Samsung NAND chip detection, introduced by some rework which went into
3.7. The initial fix wasn't quite complete, so it's in two parts. In
fact the first part is committed twice (Artem committed his own copy
of the same patch) and I've merged Artem's tree into mine which
already had that fix.
I'd have recommitted that to make it somewhat cleaner, but figured by
this point in the release cycle it was better to merge *exactly* the
commits which have been in linux-next.
If I'd recommitted, I'd also omit the sparse warning fix. But it's
there, and it's harmless — just marking one function as 'static' in
onenand code.
This also includes a couple more fixes for stable: an AB-BA deadlock
in JFFS2, and an invalid range check in slram."
* tag 'for-linus-20121123' of git://git.infradead.org/mtd-2.6:
mtd: nand: fix Samsung SLC detection regression
mtd: nand: fix Samsung SLC NAND identification regression
jffs2: Fix lock acquisition order bug in jffs2_write_begin
mtd: onenand: Make flexonenand_set_boundary static
mtd: slram: invalid checking of absolute end address
mtd: ofpart: Fix incorrect NULL check in parse_ofoldpart_partitions()
mtd: nand: fix Samsung SLC NAND identification regression
|
|
Commit 09e05d48 introduced a wait for transaction commit into
journal_unmap_buffer() in the case we are truncating a buffer undergoing commit
in the page stradding i_size on a filesystem with blocksize < pagesize. Sadly
we forgot to drop buffer lock before waiting for transaction commit and thus
deadlock is possible when kjournald wants to lock the buffer.
Fix the problem by dropping the buffer lock before waiting for transaction
commit. Since we are still holding page lock (and that is OK), buffer cannot
disappear under us.
CC: stable@vger.kernel.org # Wherever commit 09e05d48 was taken
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull reiserfs and ext3 fixes from Jan Kara:
"Fixes of reiserfs deadlocks when quotas are enabled (locking there was
completely busted by BKL conversion) and also one small ext3 fix in
the trim interface."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext3: Avoid underflow of in ext3_trim_fs()
reiserfs: Move quota calls out of write lock
reiserfs: Protect reiserfs_quota_write() with write lock
reiserfs: Protect reiserfs_quota_on() with write lock
reiserfs: Fix lock ordering during remount
|
|
Currently if len argument in ext3_trim_fs() is smaller than one block,
the 'end' variable underflow. Avoid that by returning EINVAL if len is
smaller than file system block.
Also remove useless unlikely().
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Calls into highlevel quota code cannot happen under the write lock. These
calls take dqio_mutex which ranks above write lock. So drop write lock
before calling back into quota code.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Calls into reiserfs journalling code and reiserfs_get_block() need to
be protected with write lock. We remove write lock around calls to high
level quota code in the next patch so these paths would suddently become
unprotected.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
In reiserfs_quota_on() we do quite some work - for example unpacking
tail of a quota file. Thus we have to hold write lock until a moment
we call back into the quota code.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
When remounting reiserfs dquot_suspend() or dquot_resume() can be called.
These functions take dqonoff_mutex which ranks above write lock so we have
to drop it before calling into quota code.
CC: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
If the FAN_Q_OVERFLOW bit set in event->mask, the fanotify event
metadata will not contain a valid file descriptor, but
copy_event_to_user() didn't check for that, and unconditionally does a
fd_install() on the file descriptor.
Which in turn will cause a BUG_ON() in __fd_install().
Introduced by commit 352e3b249284 ("fanotify: sanitize failure exits in
copy_event_to_user()")
Mea culpa - missed that path ;-/
Reported-by: Alex Shi <lkml.alex@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc VFS fixes from Al Viro:
"Remove a bogus BUG_ON() that can trigger spuriously + alpha bits of
do_mount() constification I'd missed during the merge window."
This pull request came in a week ago, I missed it for some reason.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill bogus BUG_ON() in do_close_on_exec()
missing const in alpha callers of do_mount()
|
|
Pull xfs bugfixes from Ben Myers:
- fix attr tree double split corruption
- fix broken error handling in xfs_vm_writepage
- drop buffer io reference when a bad bio is built
* tag 'for-linus-v3.7-rc7' of git://oss.sgi.com/xfs/xfs:
xfs: drop buffer io reference when a bad bio is built
xfs: fix broken error handling in xfs_vm_writepage
xfs: fix attr tree double split corruption
|
|
Error handling in xfs_buf_ioapply_map() does not handle IO reference
counts correctly. We increment the b_io_remaining count before
building the bio, but then fail to decrement it in the failure case.
This leads to the buffer never running IO completion and releasing
the reference that the IO holds, so at unmount we can leak the
buffer. This leak is captured by this assert failure during unmount:
XFS: Assertion failed: atomic_read(&pag->pag_ref) == 0, file: fs/xfs/xfs_mount.c, line: 273
This is not a new bug - the b_io_remaining accounting has had this
problem for a long, long time - it's just very hard to get a
zero length bio being built by this code...
Further, the buffer IO error can be overwritten on a multi-segment
buffer by subsequent bio completions for partial sections of the
buffer. Hence we should only set the buffer error status if the
buffer is not already carrying an error status. This ensures that a
partial IO error on a multi-segment buffer will not be lost. This
part of the problem is a regression, however.
cc: <stable@vger.kernel.org>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
When we shut down the filesystem, it might first be detected in
writeback when we are allocating a inode size transaction. This
happens after we have moved all the pages into the writeback state
and unlocked them. Unfortunately, if we fail to set up the
transaction we then abort writeback and try to invalidate the
current page. This then triggers are BUG() in block_invalidatepage()
because we are trying to invalidate an unlocked page.
Fixing this is a bit of a chicken and egg problem - we can't
allocate the transaction until we've clustered all the pages into
the IO and we know the size of it (i.e. whether the last block of
the IO is beyond the current EOF or not). However, we don't want to
hold pages locked for long periods of time, especially while we lock
other pages to cluster them into the write.
To fix this, we need to make a clear delineation in writeback where
errors can only be handled by IO completion processing. That is,
once we have marked a page for writeback and unlocked it, we have to
report errors via IO completion because we've already started the
IO. We may not have submitted any IO, but we've changed the page
state to indicate that it is under IO so we must now use the IO
completion path to report errors.
To do this, add an error field to xfs_submit_ioend() to pass it the
error that occurred during the building on the ioend chain. When
this is non-zero, mark each ioend with the error and call
xfs_finish_ioend() directly rather than building bios. This will
immediately push the ioends through completion processing with the
error that has occurred.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
In certain circumstances, a double split of an attribute tree is
needed to insert or replace an attribute. In rare situations, this
can go wrong, leaving the attribute tree corrupted. In this case,
the attr being replaced is the last attr in a leaf node, and the
replacement is larger so doesn't fit in the same leaf node.
When we have the initial condition of a node format attribute
btree with two leaves at index 1 and 2. Call them L1 and L2. The
leaf L1 is completely full, there is not a single byte of free space
in it. L2 is mostly empty. The attribute being replaced - call it X
- is the last attribute in L1.
The way an attribute replace is executed is that the replacement
attribute - call it Y - is first inserted into the tree, but has an
INCOMPLETE flag set on it so that list traversals ignore it. Once
this transaction is committed, a second transaction it run to
atomically mark Y as COMPLETE and X as INCOMPLETE, so that a
traversal will now find Y and skip X. Once that transaction is
committed, attribute X is then removed.
So, the initial condition is:
+--------+ +--------+
| L1 | | L2 |
| fwd: 2 |---->| fwd: 0 |
| bwd: 0 |<----| bwd: 1 |
| fsp: 0 | | fsp: N |
|--------| |--------|
| attr A | | attr 1 |
|--------| |--------|
| attr B | | attr 2 |
|--------| |--------|
.......... ..........
|--------| |--------|
| attr X | | attr n |
+--------+ +--------+
So now we go to replace X, and see that L1:fsp = 0 - it is full so
we can't insert Y in the same leaf. So we record the the location of
attribute X so we can track it for later use, then we split L1 into
L1 and L3 and reblance across the two leafs. We end with:
+--------+ +--------+ +--------+
| L1 | | L3 | | L2 |
| fwd: 3 |---->| fwd: 2 |---->| fwd: 0 |
| bwd: 0 |<----| bwd: 1 |<----| bwd: 3 |
| fsp: M | | fsp: J | | fsp: N |
|--------| |--------| |--------|
| attr A | | attr X | | attr 1 |
|--------| +--------+ |--------|
| attr B | | attr 2 |
|--------| |--------|
.......... ..........
|--------| |--------|
| attr W | | attr n |
+--------+ +--------+
And we track that the original attribute is now at L3:0.
We then try to insert Y into L1 again, and find that there isn't
enough room because the new attribute is larger than the old one.
Hence we have to split again to make room for Y. We end up with
this:
+--------+ +--------+ +--------+ +--------+
| L1 | | L4 | | L3 | | L2 |
| fwd: 4 |---->| fwd: 3 |---->| fwd: 2 |---->| fwd: 0 |
| bwd: 0 |<----| bwd: 1 |<----| bwd: 4 |<----| bwd: 3 |
| fsp: M | | fsp: J | | fsp: J | | fsp: N |
|--------| |--------| |--------| |--------|
| attr A | | attr Y | | attr X | | attr 1 |
|--------| + INCOMP + +--------+ |--------|
| attr B | +--------+ | attr 2 |
|--------| |--------|
.......... ..........
|--------| |--------|
| attr W | | attr n |
+--------+ +--------+
And now we have the new (incomplete) attribute @ L4:0, and the
original attribute at L3:0. At this point, the first transaction is
committed, and we move to the flipping of the flags.
This is where we are supposed to end up with this:
+--------+ +--------+ +--------+ +--------+
| L1 | | L4 | | L3 | | L2 |
| fwd: 4 |---->| fwd: 3 |---->| fwd: 2 |---->| fwd: 0 |
| bwd: 0 |<----| bwd: 1 |<----| bwd: 4 |<----| bwd: 3 |
| fsp: M | | fsp: J | | fsp: J | | fsp: N |
|--------| |--------| |--------| |--------|
| attr A | | attr Y | | attr X | | attr 1 |
|--------| +--------+ + INCOMP + |--------|
| attr B | +--------+ | attr 2 |
|--------| |--------|
.......... ..........
|--------| |--------|
| attr W | | attr n |
+--------+ +--------+
But that doesn't happen properly - the attribute tracking indexes
are not pointing to the right locations. What we end up with is both
the old attribute to be removed pointing at L4:0 and the new
attribute at L4:1. On a debug kernel, this assert fails like so:
XFS: Assertion failed: args->index2 < be16_to_cpu(leaf2->hdr.count), file: fs/xfs/xfs_attr_leaf.c, line: 2725
because the new attribute location does not exist. On a production
kernel, this goes unnoticed and the code proceeds ahead merrily and
removes L4 because it thinks that is the block that is no longer
needed. This leaves the hash index node pointing to entries
L1, L4 and L2, but only blocks L1, L3 and L2 to exist. Further, the
leaf level sibling list is L1 <-> L4 <-> L2, but L4 is now free
space, and so everything is busted. This corruption is caused by the
removal of the old attribute triggering a join - it joins everything
correctly but then frees the wrong block.
xfs_repair will report something like:
bad sibling back pointer for block 4 in attribute fork for inode 131
problem with attribute contents in inode 131
would clear attr fork
bad nblocks 8 for inode 131, would reset to 3
bad anextents 4 for inode 131, would reset to 0
The problem lies in the assignment of the old/new blocks for
tracking purposes when the double leaf split occurs. The first split
tries to place the new attribute inside the current leaf (i.e.
"inleaf == true") and moves the old attribute (X) to the new block.
This sets up the old block/index to L1:X, and newly allocated
block to L3:0. It then moves attr X to the new block and tries to
insert attr Y at the old index. That fails, so it splits again.
With the second split, the rebalance ends up placing the new attr in
the second new block - L4:0 - and this is where the code goes wrong.
What is does is it sets both the new and old block index to the
second new block. Hence it inserts attr Y at the right place (L4:0)
but overwrites the current location of the attr to replace that is
held in the new block index (currently L3:0). It over writes it with
L4:1 - the index we later assert fail on.
Hopefully this table will show this in a foramt that is a bit easier
to understand:
Split old attr index new attr index
vanilla patched vanilla patched
before 1st L1:26 L1:26 N/A N/A
after 1st L3:0 L3:0 L1:26 L1:26
after 2nd L4:0 L3:0 L4:1 L4:0
^^^^ ^^^^
wrong wrong
The fix is surprisingly simple, for all this analysis - just stop
the rebalance on the out-of leaf case from overwriting the new attr
index - it's already correct for the double split case.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
