Age | Commit message (Collapse) | Author | Files | Lines |
|
Give the statfs superblock operation a dentry pointer rather than a superblock
pointer.
This complements the get_sb() patch. That reduced the significance of
sb->s_root, allowing NFS to place a fake root there. However, NFS does
require a dentry to use as a target for the statfs operation. This permits
the root in the vfsmount to be used instead.
linux/mount.h has been added where necessary to make allyesconfig build
successfully.
Interest has also been expressed for use with the FUSE and XFS filesystems.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Local variable res was initialized to 0 - no check needed here.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Convert a for-loop that explicitly references "NR_CPUS" into the
potentially more efficient for_each_possible_cpu() construct.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
If the call to nfs_intent_set_file() fails to open a file in
nfs4_proc_create(), we should return an error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This is a conversion to make the various file_operations structs in fs/
const. Basically a regexp job, with a few manual fixups
The goal is both to increase correctness (harder to accidentally write to
shared datastructures) and reducing the false sharing of cachelines with
things that get dirty in .data (while .rodata is nicely read only and thus
cache clean)
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The return value of this function is never used, so let's be honest and
declare it as void.
Some places where invalidatepage returned 0, I have inserted comments
suggesting a BUG_ON.
[akpm@osdl.org: JBD BUG fix]
[akpm@osdl.org: rework for git-nfs]
[akpm@osdl.org: don't go BUG in block_invalidate_page()]
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Cc: Robert Love <rml@tech9.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (103 commits)
SUNRPC,RPCSEC_GSS: spkm3--fix config dependencies
SUNRPC,RPCSEC_GSS: spkm3: import contexts using NID_cast5_cbc
LOCKD: Make nlmsvc_traverse_shares return void
LOCKD: nlmsvc_traverse_blocks return is unused
SUNRPC,RPCSEC_GSS: fix krb5 sequence numbers.
NFSv4: Dont list system.nfs4_acl for filesystems that don't support it.
SUNRPC,RPCSEC_GSS: remove unnecessary kmalloc of a checksum
SUNRPC: Ensure rpc_call_async() always calls tk_ops->rpc_release()
SUNRPC: Fix memory barriers for req->rq_received
NFS: Fix a race in nfs_sync_inode()
NFS: Clean up nfs_flush_list()
NFS: Fix a race with PG_private and nfs_release_page()
NFSv4: Ensure the callback daemon flushes signals
SUNRPC: Fix a 'Busy inodes' error in rpc_pipefs
NFS, NLM: Allow blocking locks to respect signals
NFS: Make nfs_fhget() return appropriate error values
NFSv4: Fix an oops in nfs4_fill_super
lockd: blocks should hold a reference to the nlm_file
NFSv4: SETCLIENTID_CONFIRM should handle NFS4ERR_DELAY/NFS4ERR_RESOURCE
NFSv4: Send the delegation stateid for SETATTR calls
...
|
|
Rewrap the overly long source code lines resulting from the previous
patch's addition of the slab cache flag SLAB_MEM_SPREAD. This patch
contains only formatting changes, and no function change.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Mark file system inode and similar slab caches subject to SLAB_MEM_SPREAD
memory spreading.
If a slab cache is marked SLAB_MEM_SPREAD, then anytime that a task that's
in a cpuset with the 'memory_spread_slab' option enabled goes to allocate
from such a slab cache, the allocations are spread evenly over all the
memory nodes (task->mems_allowed) allowed to that task, instead of favoring
allocation on the node local to the current cpu.
The following inode and similar caches are marked SLAB_MEM_SPREAD:
file cache
==== =====
fs/adfs/super.c adfs_inode_cache
fs/affs/super.c affs_inode_cache
fs/befs/linuxvfs.c befs_inode_cache
fs/bfs/inode.c bfs_inode_cache
fs/block_dev.c bdev_cache
fs/cifs/cifsfs.c cifs_inode_cache
fs/coda/inode.c coda_inode_cache
fs/dquot.c dquot
fs/efs/super.c efs_inode_cache
fs/ext2/super.c ext2_inode_cache
fs/ext2/xattr.c (fs/mbcache.c) ext2_xattr
fs/ext3/super.c ext3_inode_cache
fs/ext3/xattr.c (fs/mbcache.c) ext3_xattr
fs/fat/cache.c fat_cache
fs/fat/inode.c fat_inode_cache
fs/freevxfs/vxfs_super.c vxfs_inode
fs/hpfs/super.c hpfs_inode_cache
fs/isofs/inode.c isofs_inode_cache
fs/jffs/inode-v23.c jffs_fm
fs/jffs2/super.c jffs2_i
fs/jfs/super.c jfs_ip
fs/minix/inode.c minix_inode_cache
fs/ncpfs/inode.c ncp_inode_cache
fs/nfs/direct.c nfs_direct_cache
fs/nfs/inode.c nfs_inode_cache
fs/ntfs/super.c ntfs_big_inode_cache_name
fs/ntfs/super.c ntfs_inode_cache
fs/ocfs2/dlm/dlmfs.c dlmfs_inode_cache
fs/ocfs2/super.c ocfs2_inode_cache
fs/proc/inode.c proc_inode_cache
fs/qnx4/inode.c qnx4_inode_cache
fs/reiserfs/super.c reiser_inode_cache
fs/romfs/inode.c romfs_inode_cache
fs/smbfs/inode.c smb_inode_cache
fs/sysv/inode.c sysv_inode_cache
fs/udf/super.c udf_inode_cache
fs/ufs/super.c ufs_inode_cache
net/socket.c sock_inode_cache
net/sunrpc/rpc_pipe.c rpc_inode_cache
The choice of which slab caches to so mark was quite simple. I marked
those already marked SLAB_RECLAIM_ACCOUNT, except for fs/xfs, dentry_cache,
inode_cache, and buffer_head, which were marked in a previous patch. Even
though SLAB_RECLAIM_ACCOUNT is for a different purpose, it marks the same
potentially large file system i/o related slab caches as we need for memory
spreading.
Given that the rule now becomes "wherever you would have used a
SLAB_RECLAIM_ACCOUNT slab cache flag before (usually the inode cache), use
the SLAB_MEM_SPREAD flag too", this should be easy enough to maintain.
Future file system writers will just copy one of the existing file system
slab cache setups and tend to get it right without thinking.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove a
duplicate of ARRAY_SIZE. Some trailing whitespaces are also deleted.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: David Howells <dhowells@redhat.com>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Chris Mason <mason@suse.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Nathan Scott <nathans@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The meaning of MS_VERBOSE is backwards; if the bit is set, it really means,
"don't be verbose". This is confusing and counter-intuitive.
In addition, there is also no way to set the MS_VERBOSE flag in the
mount(8) program in util-linux, but interesting, it does define options
which would do the right thing if MS_SILENT were defined, which
unfortunately we do not:
#ifdef MS_SILENT
{ "quiet", 0, 0, MS_SILENT }, /* be quiet */
{ "loud", 0, 1, MS_SILENT }, /* print out messages. */
#endif
So the obvious fix is to deprecate the use of MS_VERBOSE and replace it
with MS_SILENT.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Thanks to Frank Filz for pointing out that we list system.nfs4_acl extended
attribute even on filesystems where we don't actually support nfs4_acl.
This is inconsistent with the e.g. ext3 POSIX ACL behaviour, and seems to
annoy cp.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Currently this will not happen if we exit before rpc_new_task() was called.
Also fix up rpc_run_task() to do the same (for consistency).
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Kudos to Neil Brown for spotting the problem:
"in nfs_sync_inode, there is effectively the sequence:
nfs_wait_on_requests
nfs_flush_inode
nfs_commit_inode
This seems a bit racy to me as if the only requests are on the
->commit list, and nfs_commit_inode is called separately after
nfs_wait_on_requests completes, and before nfs_commit_inode start
(say: by nfs_write_inode) then none of these function will return
>0, yet there will be some pending request that aren't waited for."
The solution is to search for requests to wait upon, search for dirty
requests, and search for uncommitted requests while holding the
nfsi->req_lock
The patch also cleans up nfs_sync_inode(), getting rid of the redundant
FLUSH_WAIT flag. It turns out that we were always setting it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
We don't need to set PG_private for readahead pages, since they never get
unlocked while I/O is in progress. However there is a small race in
nfs_readpage_release() whereby the page may be unlocked, and have
PG_private set.
Fix is to have PG_private set only for the case of writes...
Also fix a bug in nfs_clear_page_writeback(): Don't attempt to clear the
radix_tree tag if we've already deleted the radix tree entry.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
If the callback daemon is signalled, but is unable to exit because it still
has users, then we need to flush signals. If not, then svc_recv() can
never sleep, and so we hang.
If we flush signals, then we also have to be prepared to resend them when
we want the thread to exit.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Currently it returns NULL, which usually gets interpreted as ENOMEM. In
fact it can mean a host of issues.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The mount statistics patches introduced a call to nfs_free_iostats that is
not only redundant, but actually causes an oops.
Also fix a memory leak due to the lack of a call to nfs_free_iostats on
unmount.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
In the case where we hold a delegation stateid, use that in for inside
SETATTR calls.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The struct file_lock does not carry a properly initialised lock,
so don't copy it as if it were.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Now that we have aio writes, it is possible for dreq->outstanding to be
zero, but for the I/O not to have completed. Convert struct nfs_direct_req
to use a completion to signal when the I/O is done.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Introduced by NFS aio+dio patches.
Test plan:
Compile kernel with CONFIG_NFS enabled on 64-bit hardware.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Make sure that we're doing our list accounting correctly.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The struct nfs_direct_req currently keeps a pointer to the file descriptor
without referencing it. This may cause problems if the parent process is
killed.
The nfs_open_context should normally have all the information that we're
currently using the filp for, and unlike fput(), is safe to release from
an rpciod process context.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Currently NFS O_DIRECT writes use FILE_SYNC so that a COMMIT is not
necessary. This simplifies the internal logic, but this could be a
difficult workload for some servers.
Instead, let's send UNSTABLE writes, and after they all complete, send a
COMMIT for the dirty range. After the COMMIT returns successfully, then do
the wake_up or fire off aio_complete().
Test plan:
Async direct I/O tests against Solaris (or any server that requires
committed unstable writes). Reboot server during test.
Based on an earlier patch by Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
We need to use nfs_commit_alloc() in fs/nfs/direct.c.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
^C against "iozone -I" is hitting the assertion in nfs_clear_inode().
Test plan:
"iozone -i0 -I -a -c" against a slow server, then control C. This should
not cause an oops.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Three atomic_t variables cause a lot of bus locking. Because they are all
used in the same places in the code, just use a single spin lock.
Now that the atomic_t variables are gone, we can remove the request size
limitation since the code no longer depends on the limited width of atomic_t
on some platforms.
Test plan:
Compile with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled. Millions of fsx
operations, iozone, OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Clean up tab damage and comments. Replace "file_offset" with more commonly
used "pos".
Test plan:
Compile with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
For async iocb's, the NFS direct write path now returns EIOCBQUEUED,
and calls aio_complete when all the requested writes are finished. The
synchronous part of the NFS direct write path behaves exactly as it
was before.
Shared mapped NFS files will have some coherency difficulties when
accessed concurrently with aio+dio. Will need to explore how this
is handled in the local file system case.
Test plan:
aio-stress with "-O". OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Pass the iocb argument all the way down to the direct write request
scheduler, and make it available in nfs_direct_write_result.
Test plan:
Compile the kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Millions of fsx-odirect ops. OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Eliminate the persistent use of automatic storage in all parts of the
NFS client's direct write path to pave the way for introducing support
for aio against files opened with the O_DIRECT flag.
Test plan:
Compile the kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Millions of fsx-odirect ops. OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Duplicate infrastructure from direct read path that will allow write
path to generate multiple write requests concurrently. This will
enable us to add support for aio in this path.
Temporarily we will lose the ability to do UNSTABLE writes followed by
a COMMIT in the direct write path. However, all applications I am
aware of that use NFS O_DIRECT currently write in relatively small
chunks, so this should not be inconvenient in any way.
Test plan:
Millions of fsx-odirect ops. OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Factor out the common piece of completing an NFS direct I/O request.
Test plan:
Compile kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Factor out a small common piece of the path that allocate nfs_direct_req
structures.
Test plan:
Compile kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
We're about to add asynchrony to the NFS direct write path. Begin by
abstracting out the common pieces in the read path.
The first piece is nfs_direct_read_wait, which works the same whether the
process is waiting for a read or a write.
Test plan:
Compile kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
For async iocb's, the NFS direct read path should return EIOCBQUEUED and
call aio_complete when all the requested reads are finished. The
synchronous part of the NFS direct read path behaves exactly as it was
before.
Test plan:
aio-stress with "-O". OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Pass the iocb argument all the way down to the direct read request
scheduler, and make it available in nfs_direct_read_result.
Test plan:
Compile the kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Millions of fsx-odirect ops. OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Eliminate the persistent use of automatic storage in all parts of the NFS
client's direct read path to pave the way for introducing support for aio
against files opened with the O_DIRECT flag.
Test plan:
Compile the kernel with CONFIG_NFS and CONFIG_NFS_DIRECTIO enabled.
Millions of fsx-odirect ops. OraSim.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
size_t is used for holding byte counts, so use it for variables storing rsize.
Note that the write path will be updated as we add support for async
O_DIRECT writes.
Test plan:
Need to verify that existing comparisons against new size_t variables behave
correctly.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|