summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2020-07-23device property: Avoid NULL pointer dereference in device_get_next_child_node()Andy Shevchenko1-1/+1
When we have no primary fwnode or when it's a software node, we may end up in the situation when fwnode is a NULL pointer. There is no point to look for secondary fwnode in such case. Add a necessary check to a condition. Fixes: 114dbb4fa7c4 ("drivers property: When no children in primary, try secondary") Reported-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Maxim Levitsky <mlevitsk@redhat.com> Link: https://lore.kernel.org/r/20200716182747.54929-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23fbdev: Detect integer underflow at "struct fbcon_ops"->clear_margins.Tetsuo Handa4-8/+8
syzbot is reporting general protection fault in bitfill_aligned() [1] caused by integer underflow in bit_clear_margins(). The cause of this problem is when and how do_vc_resize() updates vc->vc_{cols,rows}. If vc_do_resize() fails (e.g. kzalloc() fails) when var.xres or var.yres is going to shrink, vc->vc_{cols,rows} will not be updated. This allows bit_clear_margins() to see info->var.xres < (vc->vc_cols * cw) or info->var.yres < (vc->vc_rows * ch). Unexpectedly large rw or bh will try to overrun the __iomem region and causes general protection fault. Also, vc_resize(vc, 0, 0) does not set vc->vc_{cols,rows} = 0 due to new_cols = (cols ? cols : vc->vc_cols); new_rows = (lines ? lines : vc->vc_rows); exception. Since cols and lines are calculated as cols = FBCON_SWAP(ops->rotate, info->var.xres, info->var.yres); rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres); cols /= vc->vc_font.width; rows /= vc->vc_font.height; vc_resize(vc, cols, rows); in fbcon_modechanged(), var.xres < vc->vc_font.width makes cols = 0 and var.yres < vc->vc_font.height makes rows = 0. This means that const int fd = open("/dev/fb0", O_ACCMODE); struct fb_var_screeninfo var = { }; ioctl(fd, FBIOGET_VSCREENINFO, &var); var.xres = var.yres = 1; ioctl(fd, FBIOPUT_VSCREENINFO, &var); easily reproduces integer underflow bug explained above. Of course, callers of vc_resize() are not handling vc_do_resize() failure is bad. But we can't avoid vc_resize(vc, 0, 0) which returns 0. Therefore, as a band-aid workaround, this patch checks integer underflow in "struct fbcon_ops"->clear_margins call, assuming that vc->vc_cols * vc->vc_font.width and vc->vc_rows * vc->vc_font.heigh do not cause integer overflow. [1] https://syzkaller.appspot.com/bug?id=a565882df74fa76f10d3a6fec4be31098dbb37c6 Reported-and-tested-by: syzbot <syzbot+e5fd3e65515b48c02a30@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200715015102.3814-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23usb: tegra: Fix allocation for the FPCI contextJon Hunter1-1/+1
Commit 5c4e8d3781bc ("usb: host: xhci-tegra: Add support for XUSB context save/restore") is using the IPFS 'num_offsets' value when allocating memory for FPCI context instead of the FPCI 'num_offsets'. After commit cad064f1bd52 ("devres: handle zero size in devm_kmalloc()") was added system suspend started failing on Tegra186. The kernel log showed that the Tegra XHCI driver was crashing on entry to suspend when attempting the save the USB context. On Tegra186, the IPFS context has a zero length but the FPCI content has a non-zero length, and because of the bug in the Tegra XHCI driver we are incorrectly allocating a zero length array for the FPCI context. The crash seen on entering suspend when we attempt to save the FPCI context and following commit cad064f1bd52 ("devres: handle zero size in devm_kmalloc()") this now causes a NULL pointer deference when we access the memory. Fix this by correcting the amount of memory we are allocating for FPCI contexts. Cc: stable@vger.kernel.org Fixes: 5c4e8d3781bc ("usb: host: xhci-tegra: Add support for XUSB context save/restore") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200715113842.30680-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23interconnect: msm8916: Fix buswidth of pcnoc_s nodesGeorgi Djakov1-7/+7
The buswidth of the pcnoc_s_* nodes is actually not 8, but 4 bytes. Let's fix it. Reported-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Mike Tipton <mdtipton@codeaurora.org> Fixes: 30c8fa3ec61a ("interconnect: qcom: Add MSM8916 interconnect provider driver") Link: https://lore.kernel.org/r/20200709130004.12462-1-georgi.djakov@linaro.org Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200723083735.5616-3-georgi.djakov@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23interconnect: Do not skip aggregation for disabled pathsGeorgi Djakov1-3/+9
When an interconnect path is being disabled, currently we don't aggregate the requests for it afterwards. But the re-aggregation step shouldn't be skipped, as it may leave the nodes with outdated bandwidth data. This outdated data may actually keep the path still enabled and prevent the device from going into lower power states. Reported-by: Atul Dhudase <adhudase@codeaurora.org> Fixes: 7d374b209083 ("interconnect: Add helpers for enabling/disabling a path") Reviewed-by: Sibi Sankar <sibis@codeaurora.org> Tested-by: Atul Dhudase <adhudase@codeaurora.org> Reviewed-by: Atul Dhudase <adhudase@codeaurora.org> Link: https://lore.kernel.org/r/20200721120740.3436-1-georgi.djakov@linaro.org Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org> Link: https://lore.kernel.org/r/20200723083735.5616-2-georgi.djakov@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23/dev/mem: Add missing memory barriers for devmem_inodeEric Biggers1-3/+7
WRITE_ONCE() isn't the correct way to publish a pointer to a data structure, since it doesn't include a write memory barrier. Therefore other tasks may see that the pointer has been set but not see that the pointed-to memory has finished being initialized yet. Instead a primitive with "release" semantics is needed. Use smp_store_release() for this. The use of READ_ONCE() on the read side is still potentially correct if there's no control dependency, i.e. if all memory being "published" is transitively reachable via the pointer itself. But this pairing is somewhat confusing and error-prone. So just upgrade the read side to smp_load_acquire() so that it clearly pairs with smp_store_release(). Cc: Arnd Bergmann <arnd@arndb.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 3234ac664a87 ("/dev/mem: Revoke mappings when a driver claims the region") Signed-off-by: Eric Biggers <ebiggers@google.com> Cc: stable <stable@vger.kernel.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Link: https://lore.kernel.org/r/20200716060553.24618-1-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23binder: Don't use mmput() from shrinker function.Tetsuo Handa1-1/+1
syzbot is reporting that mmput() from shrinker function has a risk of deadlock [1], for delayed_uprobe_add() from update_ref_ctr() calls kzalloc(GFP_KERNEL) with delayed_uprobe_lock held, and uprobe_clear_state() from __mmput() also holds delayed_uprobe_lock. Commit a1b2289cef92ef0e ("android: binder: drop lru lock in isolate callback") replaced mmput() with mmput_async() in order to avoid sleeping with spinlock held. But this patch replaces mmput() with mmput_async() in order not to start __mmput() from shrinker context. [1] https://syzkaller.appspot.com/bug?id=bc9e7303f537c41b2b0cc2dfcea3fc42964c2d45 Reported-by: syzbot <syzbot+1068f09c44d151250c33@syzkaller.appspotmail.com> Reported-by: syzbot <syzbot+e5344baa319c9a96edec@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Michal Hocko <mhocko@suse.com> Acked-by: Todd Kjos <tkjos@google.com> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/4ba9adb2-43f5-2de0-22de-f6075c1fab50@i-love.sakura.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23Merge tag 'amd-drm-fixes-5.8-2020-07-22' of ↵Dave Airlie2-10/+9
git://people.freedesktop.org/~agd5f/linux into drm-fixes amd-drm-fixes-5.8-2020-07-22: amdgpu: - Fix crash when overclocking VegaM - Fix possible crash when editing dpm levels Signed-off-by: Dave Airlie <airlied@redhat.com> From: Alex Deucher <alexdeucher@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200723032608.3865-1-alexander.deucher@amd.com
2020-07-23Merge tag 'drm-misc-fixes-2020-07-22' of ↵Dave Airlie2-1/+3
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes * sun4i: Fix inverted HPD result; fixes an earlier fix * lima: fix timeout during reset Signed-off-by: Dave Airlie <airlied@redhat.com> From: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20200722070321.GA29190@linux-uq9g
2020-07-22cxgb4: add missing release on skb in uld_send()Navid Emamdoost1-0/+1
In the implementation of uld_send(), the skb is consumed on all execution paths except one. Release skb when returning NET_XMIT_DROP. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22net: atlantic: fix PTP on AQC10XEgor Pomozov1-1/+6
This patch fixes PTP on AQC10X. PTP support on AQC10X requires FW involvement and FW configures the TPS data arb mode itself. So we must make sure driver doesn't touch TPS data arb mode on AQC10x if PTP is enabled. Otherwise, there are no timestamps even though packets are flowing. Fixes: 2deac71ac492a ("net: atlantic: QoS implementation: min_rate") Signed-off-by: Egor Pomozov <epomozov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Remove the mdio bus on PF probe bailoutClaudiu Manoil1-0/+1
For ENETC ports that register an external MDIO bus, the bus doesn't get removed on the error bailout path of enetc_pf_probe(). This issue became much more visible after recent: commit 07095c025ac2 ("net: enetc: Use DT protocol information to set up the ports") Before this commit, one could make probing fail on the error path only by having register_netdev() fail, which is unlikely. But after this commit, because it moved the enetc_of_phy_get() call up in the probing sequence, now we can trigger an mdiobus_free() bug just by forcing enetc_alloc_msix() to return error, i.e. with the 'pci=nomsi' kernel bootarg (since ENETC relies on MSI support to work), as the calltrace below shows: kernel BUG at /home/eiz/work/enetc/net/drivers/net/phy/mdio_bus.c:648! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [...] Hardware name: LS1028A RDB Board (DT) pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--) pc : mdiobus_free+0x50/0x58 lr : devm_mdiobus_free+0x14/0x20 [...] Call trace: mdiobus_free+0x50/0x58 devm_mdiobus_free+0x14/0x20 release_nodes+0x138/0x228 devres_release_all+0x38/0x60 really_probe+0x1c8/0x368 driver_probe_device+0x5c/0xc0 device_driver_attach+0x74/0x80 __driver_attach+0x8c/0xd8 bus_for_each_dev+0x7c/0xd8 driver_attach+0x24/0x30 bus_add_driver+0x154/0x200 driver_register+0x64/0x120 __pci_register_driver+0x44/0x50 enetc_pf_driver_init+0x24/0x30 do_one_initcall+0x60/0x1c0 kernel_init_freeable+0x1fc/0x274 kernel_init+0x14/0x110 ret_from_fork+0x10/0x34 Fixes: ebfcb23d62ab ("enetc: Add ENETC PF level external MDIO support") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22Merge tag 'media/v5.8-3' of ↵Linus Torvalds29-1929/+1279
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media into master Pull media fixes from Mauro Carvalho Chehab: "A series of fixes for the upcoming atomisp driver. They solve issues when probing atomisp on devices with multiple cameras and get rid of warnings when built with W=1. The diffstat is a bit long, as this driver has several abstractions. The patches that solved the issues with W=1 had to get rid of some duplicated code (there used to have 2 versions of the same code, one for ISP2401 and another one for ISP2400). As this driver is not in 5.7, such changes won't cause regressions" * tag 'media/v5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (38 commits) Revert "media: atomisp: keep the ISP powered on when setting it" media: atomisp: fix mask and shift operation on ISPSSPM0 media: atomisp: move system_local consts into a C file media: atomisp: get rid of version-specific system_local.h media: atomisp: move global stuff into a common header media: atomisp: remove non-used 32-bits consts at system_local media: atomisp: get rid of some unused static vars media: atomisp: Fix error code in ov5693_probe() media: atomisp: Replace trace_printk by pr_info media: atomisp: Fix __func__ style warnings media: atomisp: fix help message for ISP2401 selection media: atomisp: i2c: atomisp-ov2680.c: fixed a brace coding style issue. media: atomisp: make const arrays static, makes object smaller media: atomisp: Clean up non-existing folders from Makefile media: atomisp: Get rid of ACPI specifics in gmin_subdev_add() media: atomisp: Provide Gmin subdev as parameter to gmin_subdev_add() media: atomisp: Use temporary variable for device in gmin_subdev_add() media: atomisp: Refactor PMIC detection to a separate function media: atomisp: Deduplicate return ret in gmin_i2c_write() media: atomisp: Make pointer to PMIC client global ...
2020-07-22staging: wlan-ng: properly check endpoint typesRustam Kovhaev1-1/+15
As syzkaller detected, wlan-ng driver does not do sanity check of endpoints in prism2sta_probe_usb(), add check for xfer direction and type Reported-and-tested-by: syzbot+c2a1fa67c02faa0de723@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=c2a1fa67c02faa0de723 Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200722161052.999754-1-rkovhaev@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-22Revert "PCI/PM: Assume ports without DLL Link Active train links in 100 ms"Bjorn Helgaas1-21/+9
This reverts commit ec411e02b7a2e785a4ed9ed283207cd14f48699d. Patrick reported that this commit broke hybrid graphics on a ThinkPad X1 Extreme 2nd with Intel UHD Graphics 630 and NVIDIA GeForce GTX 1650 Mobile: nouveau 0000:01:00.0: fifo: PBDMA0: 01000000 [] ch 0 [00ff992000 DRM] subc 0 mthd 0008 data 00000000 Karol reported that this commit broke Nouveau firmware loading on a Lenovo P1G2 with Intel UHD Graphics 630 and NVIDIA TU117GLM [Quadro T1000 Mobile]: nouveau 0000:01:00.0: acr: AHESASC binary failed In both cases, reverting ec411e02b7a2 solved the problem. Unfortunately, this revert will reintroduce the "Thunderbolt bridges take long time to resume from D3cold" problem: https://bugzilla.kernel.org/show_bug.cgi?id=206837 Link: https://lore.kernel.org/r/CAErSpo5sTeK_my1dEhWp7aHD0xOp87+oHYWkTjbL7ALgDbXo-Q@mail.gmail.com Link: https://lore.kernel.org/r/CACO55tsAEa5GXw5oeJPG=mcn+qxNvspXreJYWDJGZBy5v82JDA@mail.gmail.com Link: https://bugzilla.kernel.org/show_bug.cgi?id=208597 Reported-by: Patrick Volkerding <volkerdi@gmail.com> Reported-by: Karol Herbst <kherbst@redhat.com> Fixes: ec411e02b7a2 ("PCI/PM: Assume ports without DLL Link Active train links in 100 ms") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2020-07-22virtio-mmio: Reject invalid IRQ 0 command line argumentBjorn Helgaas1-2/+2
The "virtio_mmio.device=" command line argument allows a user to specify the size, address, and IRQ of a virtio device. Previously the only requirement for the IRQ was that it be an unsigned integer. Zero is an unsigned integer but an invalid IRQ number, and after a85a6c86c25be ("driver core: platform: Clarify that IRQ 0 is invalid"), attempts to use IRQ 0 cause warnings. If the user specifies IRQ 0, return failure instead of registering a device with IRQ 0. Fixes: a85a6c86c25be ("driver core: platform: Clarify that IRQ 0 is invalid") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com>
2020-07-22iommu/qcom: Use domain rather than dev as tlb cookieRob Clark1-20/+17
The device may be torn down, but the domain should still be valid. Lets use that as the tlb flush ops cookie. Fixes a problem reported in [1] [1] https://lkml.org/lkml/2020/7/20/104 Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org> Fixes: 09b5dfff9ad6 ("iommu/qcom: Use accessor functions for iommu private data") Link: https://lore.kernel.org/r/20200720155217.274994-1-robdclark@gmail.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2020-07-22i2c: cadence: Clear HOLD bit at correct time in Rx pathRaviteja Narayanam1-9/+10
There are few issues on Zynq SOC observed in the stress tests causing timeout errors. Even though all the data is received, timeout error is thrown. This is due to an IP bug in which the COMP bit in ISR is not set at end of transfer and completion interrupt is not generated. This bug is seen on Zynq platforms when the following condition occurs: Master read & HOLD bit set & Transfer size register reaches '0'. One workaround is to clear the HOLD bit before the transfer size register reaches '0'. The current implementation checks for this at the start of the loop and also only for less than FIFO DEPTH case (ignoring the equal to case). So clear the HOLD bit when the data yet to receive is less than or equal to the FIFO DEPTH. This avoids the IP bug condition. Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-22Revert "i2c: cadence: Fix the hold bit setting"Raviteja Narayanam1-7/+2
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9. There are two issues with "i2c: cadence: Fix the hold bit setting" commit. 1. In case of combined message request from user space, when the HOLD bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent on the bus even before the last message is started. This is because when the HOLD bit is cleared, the FIFOS are empty and there is no pending transfer. The STOP condition should occur only after the last message is completed. 2. The code added by the commit is redundant. Driver is handling the setting/clearing of HOLD bit in right way before the commit. The setting of HOLD bit based on 'bus_hold_flag' is taken care in cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv functions. The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and cdns_i2c_recv functions based on bus_hold_flag and byte count. Since clearing of HOLD bit is done after the slave address is written to the register (writing to address register triggers the message transfer), it is ensured that STOP condition occurs at the right time after completion of the pending transfer (last message). Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-21net: ethernet: ti: add NETIF_F_HW_TC hw feature flag for taprio offloadMurali Karicheri1-1/+2
Currently drive supports taprio offload which is a tc feature offloaded to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC in the net device to be compliant. This patch adds the flag. Fixes: 8127224c2708 ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support") Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: ethernet: ave: Fix error returns in ave_initWang Hai1-1/+1
When regmap_update_bits failed in ave_init(), calls of the functions reset_control_assert() and clk_disable_unprepare() were missed. Add goto out_reset_assert to do this. Fixes: 57878f2f4697 ("net: ethernet: ave: add support for phy-mode setting of system controller") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21drivers/net/wan/x25_asy: Fix to make it workXie He1-7/+14
This driver is not working because of problems of its receiving code. This patch fixes it to make it work. When the driver receives an LAPB frame, it should first pass the frame to the LAPB module to process. After processing, the LAPB module passes the data (the packet) back to the driver, the driver should then add a one-byte pseudo header and pass the data to upper layers. The changes to the "x25_asy_bump" function and the "x25_asy_data_indication" function are to correctly implement this procedure. Also, the "x25_asy_unesc" function ignores any frame that is shorter than 3 bytes. However the shortest frames are 2-byte long. So we need to change it to allow 2-byte frames to pass. Cc: Eric Dumazet <edumazet@google.com> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Reviewed-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: suppress false-positives interrupt error messages on HW initAlexander Lobakin3-24/+32
It was found that qed_pglueb_rbc_attn_handler() can produce a lot of false-positive error detections on driver load/reload (especially after crashes/recoveries) and spam the kernel log: [ 4.958275] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d00ff0 [ 2079.146764] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0 [ 2116.374631] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0 [ 2135.250564] [qed_pglueb_rbc_attn_handler:324()]ICPL error - 00d80ff0 [...] Reduce the logging level of two false-positive prone error messages from notice to verbose on initialization (only) to not mix it with real error attentions while debugging. Fixes: 666db4862f2d ("qed: Revise load sequence to avoid PCI errors") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: suppress "don't support RoCE & iWARP" flooding on HW initAlexander Lobakin1-2/+2
Change the verbosity of the "don't support RoCE & iWARP simultaneously" warning to debug level to stop flooding on driver/hardware initialization: [ 4.783230] qede 01:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth0] [ 4.810020] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 4.861186] qede 01:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth1] [ 4.893311] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 5.181713] qede a1:00.00: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth2] [ 5.224740] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 5.276449] qede a1:00.01: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth3] [ 5.318671] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only [ 5.369548] qede a1:00.02: Storm FW 8.37.7.0, Management FW 8.52.9.0 [MBI 15.10.6] [eth4] [ 5.411645] [qed_rdma_set_pf_params:2076()]Current day drivers don't support RoCE & iWARP simultaneously on the same PF. Default to RoCE-only Fixes: e0a8f9de16fc ("qed: Add iWARP enablement support") Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21netdevsim: fix unbalaced locking in nsim_create()Taehee Yoo1-2/+2
In the nsim_create(), rtnl_lock() is called before nsim_bpf_init(). If nsim_bpf_init() is failed, rtnl_unlock() should be called, but it isn't called. So, unbalanced locking would occur. Fixes: e05b2d141fef ("netdevsim: move netdev creation/destruction to dev probe") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: dsa: microchip: call phy_remove_link_mode during probeHelmut Grohne3-23/+23
When doing "ip link set dev ... up" for a ksz9477 backed link, ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove 1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is called. Doing so reverts any previous change to advertised link modes e.g. using a udevd .link file. phy_remove_link_mode is not meant to be used while opening a link and should be called during phy probe when the link is not yet available to userspace. Therefore move the phy_remove_link_mode calls into ksz9477_switch_register. It indirectly calls dsa_register_switch, which creates the relevant struct phy_devices and we update the link modes right after that. At that time dev->features is already initialized by ksz9477_switch_detect. Remove phy_setup from ksz_dev_ops as no users remain. Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/ Fixes: 42fc6a4c613019 ("net: dsa: microchip: prepare PHY for proper advertisement") Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: hns3: fix return value error when query MAC link status failJian Shen2-27/+25
Currently, PF queries the MAC link status per second by calling function hclge_get_mac_link_status(). It return the error code when failed to send cmdq command to firmware. It's incorrect, because this return value is used as the MAC link status, which 0 means link down, and none-zero means link up. So fixes it. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: hns3: fix error handling for desc fillingYunsheng Lin2-0/+9
The content of the TX desc is automatically cleared by the HW when the HW has sent out the packet to the wire. When desc filling fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do the error handling, which miss zeroing of the TX desc and the checking if a unmapping is needed. So add the zeroing and checking in hns3_clear_desc() to avoid the above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in desc_cb is not valid, because hns3_nic_reclaim_desc() may treat the desc_cb->type of zero as packet and add to the sent pkt statistics accordingly. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: hns3: fix for not calculating TX BD send size correctlyYunsheng Lin2-3/+1
With GRO and fraglist support, the SKB can be aggregated to a total size of 65535, and when that SKB is forwarded through a bridge, the size of the SKB may be pushed to exceed the size of 65535 when br_dev_queue_push_xmit() is called. The max send size of BD supported by the HW is 65535, when a SKB with a headlen of over 65535 is sent to the driver, the driver needs to use multi BD to send the linear data, and the send size of the last BD is calculated incorrectly by the driver who is using '&' operation, which causes a TX error. Use '%' operation to fix this problem. Fixes: 3fe13ed95dd3 ("net: hns3: avoid mult + div op in critical data path") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: hns3: fix for not unmapping TX buffer correctlyYunsheng Lin1-11/+3
When a big TX buffer is sent using multi BD, the driver maps the whole TX buffer, and unmaps it using info in desc_cb corresponding to each BD, but only the info in the desc_cb of first BD is correct, other info in desc_cb is wrong, which causes TX unmapping problem when SMMU is on. Only set the mapping and freeing info in the desc_cb of first BD to fix this problem, because the TX buffer only need to be unmapped and freed once. Fixes: 1e8a7977d09f("net: hns3: add handling for big TX fragment") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: ethernet: ravb: exit if re-initialization fails in tx timeoutYoshihiro Shimoda1-2/+24
According to the report of [1], this driver is possible to cause the following error in ravb_tx_timeout_work(). ravb e6800000.ethernet ethernet: failed to switch device to config mode This error means that the hardware could not change the state from "Operation" to "Configuration" while some tx and/or rx queue are operating. After that, ravb_config() in ravb_dmac_init() will fail, and then any descriptors will be not allocaled anymore so that NULL pointer dereference happens after that on ravb_start_xmit(). To fix the issue, the ravb_tx_timeout_work() should check the return values of ravb_stop_dma() and ravb_dmac_init(). If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX and just exits. If ravb_dmac_init() fails, just exits. [1] https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/ Reported-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21drm/amdgpu: Fix NULL dereference in dpm sysfs handlersPaweł Gronowski1-6/+3
NULL dereference occurs when string that is not ended with space or newline is written to some dpm sysfs interface (for example pp_dpm_sclk). This happens because strsep replaces the tmp with NULL if the delimiter is not present in string, which is then dereferenced by tmp[0]. Reproduction example: sudo sh -c 'echo -n 1 > /sys/class/drm/card0/device/pp_dpm_sclk' Signed-off-by: Paweł Gronowski <me@woland.xyz> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2020-07-21drm/amd/powerplay: fix a crash when overclocking Vega MQiu Wenbo1-4/+6
Avoid kernel crash when vddci_control is SMU7_VOLTAGE_CONTROL_NONE and vddci_voltage_table is empty. It has been tested on Intel Hades Canyon (i7-8809G). Bug: https://bugzilla.kernel.org/show_bug.cgi?id=208489 Fixes: ac7822b0026f ("drm/amd/powerplay: add smumgr support for VEGAM (v2)") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Qiu Wenbo <qiuwenbo@phytium.com.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2020-07-21serial: 8250_mtk: Fix high-speed baud rates clampingSerge Semin1-0/+18
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") fixed limits of a baud rate setting for a generic 8250 port. In other words since that commit the baud rate has been permitted to be within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely normal for a standard 8250 UART port. But there are custom 8250 ports, which provide extended baud rate limits. In particular the Mediatek 8250 port can work with baud rates up to "uartclk" speed. Normally that and any other peculiarity is supposed to be handled in a custom set_termios() callback implemented in the vendor-specific 8250-port glue-driver. Currently that is how it's done for the most of the vendor-specific 8250 ports, but for some reason for Mediatek a solution has been spread out to both the glue-driver and to the generic 8250-port code. Due to that a bug has been introduced, which permitted the extended baud rate limit for all even for standard 8250-ports. The bug has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") by narrowing the baud rates limit back down to the normal bounds. Unfortunately by doing so we also broke the Mediatek-specific extended bauds feature. A fix of the problem described above is twofold. First since we can't get back the extended baud rate limits feature to the generic set_termios() function and that method supports only a standard baud rates range, the requested baud rate must be locally stored before calling it and then restored back to the new termios structure after the generic set_termios() finished its magic business. By doing so we still use the serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers, while the extended baud rate setting procedure will be performed later in the custom Mediatek-specific set_termios() callback. Second since a true baud rate is now fully calculated in the custom set_termios() method we need to locally update the port timeout by calling the uart_update_timeout() function. After the fixes described above are implemented in the 8250_mtk.c driver, the Mediatek 8250-port should get back to normally working with extended baud rates. Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") Reported-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: stable <stable@vger.kernel.org> Tested-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21serial: 8250: fix null-ptr-deref in serial8250_start_tx()Yang Yingliang1-1/+1
I got null-ptr-deref in serial8250_start_tx(): [ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 78.123778] Mem abort info: [ 78.126560] ESR = 0x86000007 [ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits [ 78.134891] SET = 0, FnV = 0 [ 78.137933] EA = 0, S1PTW = 0 [ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600 [ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000 [ 78.160029] Internal error: Oops: 86000007 [#1] SMP [ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd [ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48 [ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020 [ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--) [ 78.228435] pc : 0x0 [ 78.230618] lr : serial8250_start_tx+0x160/0x260 [ 78.235215] sp : ffff800062eefb80 [ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff [ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000 [ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000 [ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002 [ 78.259679] x21: 0000000000000001 x20: 0000000000000000 [ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000 [ 78.270259] x17: 0000000000000000 x16: 0000000000000000 [ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6 [ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539 [ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0 [ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88 [ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000 [ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8 [ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002 [ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8 [ 78.317873] Call trace: [ 78.320312] 0x0 [ 78.322147] __uart_start.isra.9+0x64/0x78 [ 78.326229] uart_start+0xb8/0x1c8 [ 78.329620] uart_flush_chars+0x24/0x30 [ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30 [ 78.338128] n_tty_receive_buf+0x44/0x2c8 [ 78.342122] tty_ioctl+0x348/0x11f8 [ 78.345599] ksys_ioctl+0xd8/0xf8 [ 78.348903] __arm64_sys_ioctl+0x2c/0xc8 [ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0 [ 78.357583] do_el0_svc+0x44/0xd0 [ 78.360887] el0_sync_handler+0x14c/0x1d0 [ 78.364880] el0_sync+0x140/0x180 [ 78.368185] Code: bad PC value SERIAL_PORT_DFNS is not defined on each arch, if it's not defined, serial8250_set_defaults() won't be called in serial8250_isa_init_ports(), so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref. Fix this problem by calling serial8250_set_defaults() after init uart port. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21serial: tegra: drop bogus NULL tty-port checksJohan Hovold1-9/+4
The struct tty_port is part of the uart state and will never be NULL in the receive helpers. Drop the bogus NULL checks and rename the pointer-variables "port" to differentiate them from struct tty_struct pointers (which can be NULL). Fixes: 962963e4ee23 ("serial: tegra: Switch to using struct tty_port") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200710135947.2737-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21serial: tegra: fix CREAD handling for PIOJohan Hovold1-2/+5
Commit 33ae787b74fc ("serial: tegra: add support to ignore read") added support for dropping input in case CREAD isn't set, but for PIO the ignore_status_mask wasn't checked until after the character had been put in the receive buffer. Note that the NULL tty-port test is bogus and will be removed by a follow-on patch. Fixes: 33ae787b74fc ("serial: tegra: add support to ignore read") Cc: stable <stable@vger.kernel.org> # 5.4 Cc: Shardar Shariff Md <smohammed@nvidia.com> Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21RDMA/mlx5: Prevent prefetch from racing with implicit destructionJason Gunthorpe1-3/+19
Prefetch work in mlx5_ib_prefetch_mr_work can be queued and able to run concurrently with destruction of the implicit MR. The num_deferred_work was intended to serialize this, but there is a race: CPU0 CPU1 mlx5_ib_free_implicit_mr() xa_erase(odp_mkeys) synchronize_srcu() __xa_erase(implicit_children) mlx5_ib_prefetch_mr_work() pagefault_mr() pagefault_implicit_mr() implicit_get_child_mr() xa_cmpxchg() atomic_dec_and_test(num_deferred_mr) wait_event(imr->q_deferred_work) ib_umem_odp_release(odp_imr) kfree(odp_imr) At this point in mlx5_ib_free_implicit_mr() the implicit_children list is supposed to be empty forever so that destroy_unused_implicit_child_mr() and related are not and will not be running. Since it is not empty the destroy_unused_implicit_child_mr() flow ends up touching deallocated memory as mlx5_ib_free_implicit_mr() already tore down the imr parent. The solution is to flush out the prefetch wq by driving num_deferred_work to zero after creation of new prefetch work is blocked. Fixes: 5256edcb98a1 ("RDMA/mlx5: Rework implicit ODP destroy") Link: https://lore.kernel.org/r/20200719065435.130722-1-leon@kernel.org Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2020-07-21tty: xilinx_uartps: Really fix id assignmentHelmut Grohne1-2/+6
The problems started with the revert (18cc7ac8a28e28). The cdns_uart_console.index is statically assigned -1. When the port is registered, Linux assigns consecutive numbers to it. It turned out that when using ttyPS1 as console, the index is not updated as we are reusing the same cdns_uart_console instance for multiple ports. When registering ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it already is 0 and not updated. That led to 2ae11c46d5fdc4. It assigns the index prior to registering the uart_driver once. Unfortunately, that ended up breaking the situation where the probe order does not match the id order. When using the same device tree for both uboot and linux, it is important that the serial0 alias points to the console. So some boards reverse those aliases. This was reported by Jan Kiszka. The proposed fix was reverting the index assignment and going back to the previous iteration. However such a reversed assignement (serial0 -> uart1, serial1 -> uart0) was already partially broken by the revert (18cc7ac8a28e28). While the ttyPS device works, the kmsg connection is already broken and kernel messages go missing. Reverting the id assignment does not fix this. >From the xilinx_uartps driver pov (after reverting the refactoring commits), there can be only one console. This manifests in static variables console_pprt and cdns_uart_console. These variables are not properly linked and can go out of sync. The cdns_uart_console.index is important for uart_add_one_port. We call that function for each port - one of which hopefully is the console. If it isn't, the CON_ENABLED flag is not set and console_port is cleared. The next cdns_uart_probe call then tries to register the next port using that same cdns_uart_console. It is important that console_port and cdns_uart_console (and its index in particular) stay in sync. The index assignment implemented by Shubhrajyoti Datta is correct in principle. It just may have to happen a second time if the first cdns_uart_probe call didn't encounter the console device. And we shouldn't change the index once the console uart is registered. Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Reported-by: Jan Kiszka <jan.kiszka@web.de> Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/ Fixes: 18cc7ac8a28e28 ("Revert "serial: uartps: Register own uart console and driver structures"") Fixes: 2ae11c46d5fdc4 ("tty: xilinx_uartps: Fix missing id assignment to the console") Fixes: 76ed2e10579671 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"") Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21vt: Reject zero-sized screen buffer size.Tetsuo Handa1-11/+18
syzbot is reporting general protection fault in do_con_write() [1] caused by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0 caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate() from con_install() from tty_init_dev() from tty_open() on such console causes vc->vc_pos == 0x10000000e due to ((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1). I don't think that a console with 0 column or 0 row makes sense. And it seems that vc_do_resize() does not intend to allow resizing a console to 0 column or 0 row due to new_cols = (cols ? cols : vc->vc_cols); new_rows = (lines ? lines : vc->vc_rows); exception. Theoretically, cols and rows can be any range as long as 0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g. cols == 1048576 && rows == 2 is possible) because of vc->vc_size_row = vc->vc_cols << 1; vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row; in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate(). Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return an error, and con_write() will not be called on a console with 0 column or 0 row. We need to make sure that integer overflow in visual_init() won't happen. Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying 1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate() will be practically fine. This patch does not touch con_init(), for returning -EINVAL there does not help when we are not returning -ENOMEM. [1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8 Reported-and-tested-by: syzbot <syzbot+017265e8553724e514e8@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200712111013.11881-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4Tony Lindgren2-10/+58
Carlos Hernandez <ceh@ti.com> reported that we now have a suspend and resume regresssion on am3 and am4 compared to the earlier kernels. While suspend and resume works with v5.8-rc3, we now get errors with rtcwake: pm33xx pm33xx: PM: Could not transition all powerdomains to target state ... rtcwake: write error This is because we now fail to idle the system timer clocks that the idle code checks and the error gets propagated to the rtcwake. Turns out there are several issues that need to be fixed: 1. Ignore no-idle and no-reset configured timers for the ti-sysc interconnect target driver as otherwise it will keep the system timer clocks enabled 2. Toggle the system timer functional clock for suspend for am3 and am4 (but not for clocksource on am3) 3. Only reconfigure type1 timers in dmtimer_systimer_disable() 4. Use of_machine_is_compatible() instead of of_device_is_compatible() for checking the SoC type Fixes: 52762fbd1c47 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support") Reported-by: Carlos Hernandez <ceh@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Carlos Hernandez <ceh@ti.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200713162601.6829-1-tony@atomide.com
2020-07-21usb: xhci: Fix ASM2142/ASM3142 DMA addressingForest Crossman1-0/+3
The ASM2142/ASM3142 (same PCI IDs) does not support full 64-bit DMA addresses, which can cause silent memory corruption or IOMMU errors on platforms that use the upper bits. Add the XHCI_NO_64BIT_SUPPORT quirk to fix this issue. Signed-off-by: Forest Crossman <cyrozap@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200717112734.328432-1-cyrozap@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-21usb: xhci-mtk: fix the failure of bandwidth allocationChunfeng Yun1-0/+4
The wMaxPacketSize field of endpoint descriptor may be zero as default value in alternate interface, and they are not actually selected when start stream, so skip them when try to allocate bandwidth. Cc: stable <stable@vger.kernel.org> Fixes: 0cbd4b34cda9 ("xhci: mediatek: support MTK xHCI host controller") Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1594360672-2076-1-git-send-email-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-20net: neterion: vxge: reduce stack usage in VXGE_COMPLETE_VPATH_TXBixuan Cui1-1/+1
Fix the warning: [-Werror=-Wframe-larger-than=] drivers/net/ethernet/neterion/vxge/vxge-main.c: In function'VXGE_COMPLETE_VPATH_TX.isra.37': drivers/net/ethernet/neterion/vxge/vxge-main.c:119:1: warning: the frame size of 1056 bytes is larger than 1024 bytes Dropping the NR_SKB_COMPLETED to 16 is appropriate that won't have much impact on performance and functionality. Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20scsi: core: Run queue in case of I/O resource contention failureMing Lei1-5/+11
I/O requests may be held in scheduler queue because of resource contention. The starvation scenario was handled properly in the regular completion path but we failed to account for it during I/O submission. This lead to the hang captured below. Make sure we run the queue when resource contention is encountered in the submission path. [ 39.054963] scsi 13:0:0:0: rejecting I/O to dead device [ 39.058700] scsi 13:0:0:0: rejecting I/O to dead device [ 39.087855] sd 13:0:0:1: [sdd] Synchronizing SCSI cache [ 39.088909] scsi 13:0:0:1: rejecting I/O to dead device [ 39.095351] scsi 13:0:0:1: rejecting I/O to dead device [ 39.096962] scsi 13:0:0:1: rejecting I/O to dead device [ 247.021859] INFO: task scsi-stress-rem:813 blocked for more than 122 seconds. [ 247.023258] Not tainted 5.8.0-rc2 #8 [ 247.024069] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 247.025331] scsi-stress-rem D 0 813 802 0x00004000 [ 247.025334] Call Trace: [ 247.025354] __schedule+0x504/0x55f [ 247.027987] schedule+0x72/0xa8 [ 247.027991] blk_mq_freeze_queue_wait+0x63/0x8c [ 247.027994] ? do_wait_intr_irq+0x7a/0x7a [ 247.027996] blk_cleanup_queue+0x4b/0xc9 [ 247.028000] __scsi_remove_device+0xf6/0x14e [ 247.028002] scsi_remove_device+0x21/0x2b [ 247.029037] sdev_store_delete+0x58/0x7c [ 247.029041] kernfs_fop_write+0x10d/0x14f [ 247.031281] vfs_write+0xa2/0xdf [ 247.032670] ksys_write+0x6b/0xb3 [ 247.032673] do_syscall_64+0x56/0x82 [ 247.034053] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 247.034059] RIP: 0033:0x7f69f39e9008 [ 247.036330] Code: Bad RIP value. [ 247.036331] RSP: 002b:00007ffdd8116498 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 247.037613] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f69f39e9008 [ 247.039714] RDX: 0000000000000002 RSI: 000055cde92a0ab0 RDI: 0000000000000001 [ 247.039715] RBP: 000055cde92a0ab0 R08: 000000000000000a R09: 00007f69f3a79e80 [ 247.039716] R10: 000000000000000a R11: 0000000000000246 R12: 00007f69f3abb780 [ 247.039717] R13: 0000000000000002 R14: 00007f69f3ab6740 R15: 0000000000000002 Link: https://lore.kernel.org/r/20200720025435.812030-1-ming.lei@redhat.com Cc: linux-block@vger.kernel.org Cc: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-07-20net: ag71xx: add missed clk_disable_unprepare in error path of probeHuang Guobin1-1/+2
The ag71xx_mdio_probe() forgets to call clk_disable_unprepare() when of_reset_control_get_exclusive() failed. Add the missed call to fix it. Fixes: d51b6ce441d3 ("net: ethernet: add ag71xx driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Huang Guobin <huangguobin4@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20nfc: s3fwrn5: add missing release on skb in s3fwrn5_recv_frameNavid Emamdoost1-0/+1
The implementation of s3fwrn5_recv_frame() is supposed to consume skb on all execution paths. Release skb before returning -ENODEV. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20crypto/chtls: correct net_device reference countVinay Kumar Yadav1-1/+1
ip_dev_find() call holds net_device reference which is not needed, use __ip_dev_find() which does not hold reference. v1->v2: - Correct submission tree. - Add fixes tag. Fixes: cc35c88ae4db ("crypto : chtls - CPL handler definition") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20crypto/chtls: fix tls alert messages corrupted by tls dataVinay Kumar Yadav1-3/+4
When tls data skb is pending for Tx and tls alert comes , It is wrongly overwrite the record type of tls data to tls alert record type. fix the issue correcting it. v1->v2: - Correct submission tree. - Add fixes tag. Fixes: 6919a8264a32 ("Crypto/chtls: add/delete TLS header in driver") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-20ionic: use mutex to protect queue operationsShannon Nelson3-25/+17
The ionic_wait_on_bit_lock() was a open-coded mutex knock-off used only for protecting the queue reset operations, and there was no reason not to use the real thing. We can use the lock more correctly and to better protect the queue stop and start operations from cross threading. We can also remove a useless and expensive bit operation from the Rx path. This fixes a case found where the link_status_check from a link flap could run into an MTU change and cause a crash. Fixes: beead698b173 ("ionic: Add the basic NDO callbacks for netdev support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-21 02:17:46 +0000