summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2019-12-27net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCsMartin Blumenstingl1-3/+11
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate can be adjusted at runtime. So far we have been running MPLL2 with ~250MHz (and the internal m250_div with value 1), which worked enough that we could transfer data with an TX delay of 4ns. Unfortunately there is high packet loss with an RGMII PHY when transferring data (receiving data works fine though). Odroid-C1's u-boot is running with a TX delay of only 2ns as well as the internal m250_div set to 2 - no lost (TX) packets can be observed with that setting in u-boot. Manual testing has shown that the TX packet loss goes away when using the following settings in Linux (the vendor kernel uses the same settings): - MPLL2 clock set to ~500MHz - m250_div set to 2 - TX delay set to 2ns on the MAC side Update the m250_div divider settings to only accept dividers greater or equal 2 to fix the TX delay generated by the MAC. iperf3 results before the change: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender [ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver iperf3 results after the change (including an updated TX delay of 2ns): [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender [ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27spi: Don't look at TX buffer for PTP system timestampingVladimir Oltean2-17/+14
The API for PTP system timestamping (associating a SPI transaction with the system time at which it was transferred) is flawed: it assumes that the xfer->tx_buf pointer will always be present. This is, of course, not always the case. So introduce a "progress" variable that denotes how many word have been transferred. Fix the Freescale DSPI driver, the only user of the API so far, in the same patch. Fixes: b42faeee718c ("spi: Add a PTP system timestamp to the transfer structure") Fixes: d6b71dfaeeba ("spi: spi-fsl-dspi: Implement the PTP system timestamping for TCFQ mode") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20191227012417.1057-1-olteanv@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-12-27Merge tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drmLinus Torvalds14-86/+139
Pull drm fixes from Dave Airlie: "Post-xmas food coma recovery fixes. Only three fixes for i915 since I expect most people are holidaying. i915: - power management rc6 fix - framebuffer tracking fix - display power management ratelimit fix" * tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm: drm/i915: Hold reference to intel_frontbuffer as we track activity drm/i915/gt: Ratelimit display power w/a drm/i915/pmu: Ensure monotonic rc6
2019-12-27Merge tag 'pm-5.5-rc4' of ↵Linus Torvalds1-4/+1
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fixes from Rafael Wysocki: "Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and remove redundant Kconfig dependencies from multiple devfreq drivers (Leonard Crestez)" * tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PM / devfreq: tegra: Add COMMON_CLK dependency PM / devfreq: Drop explicit selection of PM_OPP
2019-12-27Merge tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-blockLinus Torvalds6-44/+125
Pull libata fixes from Jens Axboe: "Two things in here: - First half of a series that fixes ahci_brcm, also marked for stable. The other part of the series is going into 5.6 (Florian) - sata_nv regression fix that is also marked for stable (Sascha)" * tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block: ata: ahci_brcm: Add missing clock management during recovery ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE ata: ahci_brcm: Fix AHCI resources management ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys() libata: Fix retrieving of active qcs
2019-12-27Merge tag 'block-5.5-20191226' of git://git.kernel.dk/linux-blockLinus Torvalds1-1/+1
Pull block fixes from Jens Axboe: "Only thing here are the changes from Arnd from last week, which now have the appropriate header include to ensure they actually compile if COMPAT is enabled" * tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block: compat_ioctl: block: handle Persistent Reservations compat_ioctl: block: handle add zone open, close and finish ioctl compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE pktcdvd: fix regression on 64-bit architectures
2019-12-27Merge tag 'gpio-v5.5-2' of ↵Linus Torvalds8-28/+34
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO fixes from Linus Walleij: "A set of fixes for the v5.5 series: - Fix the build for the Xtensa driver. - Make sure to set up the parent device for mpc8xxx. - Clarify the look-up error message. - Fix the usage of the line direction in the mockup device. - Fix a type warning on the Aspeed driver. - Remove the pointless __exit annotation on the xgs-iproc which is causing a compilation problem. - Fix up emultation of open drain outputs .get_direction() - Fix the IRQ callbacks on the PCA953xx to use bitops and work properly. - Fix the Kconfig on the Tegra driver" * tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio: tegra186: Allow building on Tegra194-only configurations gpio: pca953x: Switch to bitops in IRQ callbacks gpiolib: fix up emulated open drain outputs MAINTAINERS: Append missed file to the database gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove gpio: aspeed: avoid return type warning gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION gpio: Fix error message on out-of-range GPIO in lookup table gpio: mpc8xxx: Add platform device to gpiochip->parent gpio: xtensa: fix driver build
2019-12-27ioat: ioat_alloc_ring() failure handling.Alexander.Barabash@dell.com1-1/+2
If dma_alloc_coherent() returns NULL in ioat_alloc_ring(), ring allocation must not proceed. Until now, if the first call to dma_alloc_coherent() in ioat_alloc_ring() returned NULL, the processing could proceed, failing with NULL-pointer dereferencing further down the line. Signed-off-by: Alexander Barabash <alexander.barabash@dell.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/75e9c0e84c3345d693c606c64f8b9ab5@x13pwhopdag1307.AMER.DELL.COM Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-12-26bnx2x: Fix accounting of vlan resources among the PFsManish Chopra1-1/+4
While testing max vlan configuration on the PF, firmware gets assert as driver was configuring number of vlans more than what is supported per port/engine, it was figured out that there is an implicit vlan (hidden default vlan consuming hardware cam entry resource) which is configured default for all the clients (PF/VFs) on client_init ramrod by the adapter implicitly, so when allocating resources among the PFs this implicit vlan should be considered or total vlan entries should be reduced by one to accommodate that default/implicit vlan entry. Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26bnx2x: Use appropriate define for vlan creditManish Chopra1-1/+1
Although it has same value as MAX_MAC_CREDIT_E2, use MAX_VLAN_CREDIT_E2 appropriately. Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26net: phy: aquantia: add suspend / resume ops for AQR105Madalin Bucur1-0/+2
The suspend/resume code for AQR107 works on AQR105 too. This patch fixes issues with the partner not seeing the link down when the interface using AQR105 is brought down. Fixes: bee8259dd31f ("net: phy: add driver for aquantia phy") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26dpaa_eth: fix DMA mapping leakMadalin Bucur1-19/+20
On the error path some fragments remain DMA mapped. Adding a fix that unmaps all the fragments. Rework cleanup path to be simpler. Fixes: 8151ee88bad5 ("dpaa_eth: use page backed rx buffers") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26net/mlxfw: Fix out-of-memory error in mfa2 flash burningVladyslav Tarasiuk1-3/+4
The burning process requires to perform internal allocations of large chunks of memory. This memory doesn't need to be contiguous and can be safely allocated by vzalloc() instead of kzalloc(). This patch changes such allocation to avoid possible out-of-memory failure. Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-25ata: ahci_brcm: Add missing clock management during recoveryFlorian Fainelli1-0/+7
The downstream implementation of ahci_brcm.c did contain clock management recovery, but until recently, did that outside of the libahci_platform helpers and this was unintentionally stripped out while forward porting the patch upstream. Add the missing clock management during recovery and sleep for 10 milliseconds per the design team recommendations to ensure the SATA PHY controller and AFE have been fully quiesced. Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-12-25ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINEFlorian Fainelli1-15/+16
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making it conforming to the 'strict' AHCI implementation which this controller is based on. This solves long link establishment with specific hard drives (e.g.: Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the error recovery handling before finally establishing a succesful SATA link at the desired speed. We re-order the hpriv->flags assignment to also remove the NONCQ quirk since we can set the flag directly. Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms") Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-12-25ata: ahci_brcm: Fix AHCI resources managementFlorian Fainelli1-29/+76
The AHCI resources management within ahci_brcm.c is a little convoluted, largely because it historically had a dedicated clock that was managed within this file in the downstream tree. Once brough upstream though, the clock was left to be managed by libahci_platform.c which is entirely appropriate. This patch series ensures that the AHCI resources are fetched and enabled before any register access is done, thus avoiding bus errors on platforms which clock gate the controller by default. As a result we need to re-arrange the suspend() and resume() functions in order to avoid accessing registers after the clocks have been turned off respectively before the clocks have been turned on. Finally, we can refactor brcm_ahci_get_portmask() in order to fetch the number of ports from hpriv->mmio which is now accessible without jumping through hoops like we used to do. The commit pointed in the Fixes tag is both old and new enough not to require major headaches for backporting of this patch. Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-12-25ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()Florian Fainelli1-2/+4
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5 ("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are going to need ahci_platform_{enable,disable}_phys() in a subsequent commit for ahci_brcm.c in order to properly control the PHY initialization order. Also make sure the function prototypes are declared in include/linux/ahci_platform.h as a result. Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-12-25libata: Fix retrieving of active qcsSascha Hauer4-3/+27
ata_qc_complete_multiple() is called with a mask of the still active tags. mv_sata doesn't have this information directly and instead calculates the still active tags from the started tags (ap->qc_active) and the finished tags as (ap->qc_active ^ done_mask) Since 28361c40368 the hw_tag and tag are no longer the same and the equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is started and this will be in done_mask on completion. ap->qc_active ^ done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as the internal tag will never be reported as completed. This is fixed by introducing ata_qc_get_active() which returns the active hardware tags and calling it where appropriate. This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same problem. There is another case in sata_nv that most likely needs fixing as well, but this looks a little different, so I wasn't confident enough to change that. Fixes: 28361c403683 ("libata: add extra internal command") Cc: stable@vger.kernel.org Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Add missing export of ata_qc_get_active(), as per Pali. Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-12-25regulator: axp20x: Fix axp20x_set_ramp_delayAxel Lin1-3/+6
Current code set incorrect bits when set ramp_delay for AXP20X_DCDC2, fix it. Fixes: d29f54df8b16 ("regulator: axp20x: add support for set_ramp_delay for AXP209") Signed-off-by: Axel Lin <axel.lin@ingics.com> Link: https://lore.kernel.org/r/20191221081049.32490-1-axel.lin@ingics.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-12-24s390/qeth: fix initialization on old HWJulian Wiedmann1-3/+1
I stumbled over an old OSA model that claims to support DIAG_ASSIST, but then rejects the cmd to query its DIAG capabilities. In the old code this was ok, as the returned raw error code was > 0. Now that we translate the raw codes to errnos, the "rc < 0" causes us to fail the initialization of the device. The fix is trivial: don't bail out when the DIAG query fails. Such an error is not critical, we can still use the device (with a slightly reduced set of features). Fixes: 742d4d40831d ("s390/qeth: convert remaining legacy cmd callbacks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24s390/qeth: vnicc Fix init to defaultAlexandra Winter1-1/+3
During vnicc_init wanted_char should be compared to cur_char and not to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce the default values as desired values. Note, that it is expected, that a card comes online with default values. This patch was tested with private card firmware. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24s390/qeth: Fix vnicc_is_in_use if rx_bcast not setAlexandra Winter1-2/+1
Symptom: After vnicc/rx_bcast has been manually set to 0, bridge_* sysfs parameters can still be set or written. Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast. Vnic characteristics and bridgeport settings are mutually exclusive. rx_bcast defaults to 1, so manually setting it to 0 should disable bridge_* parameters. Instead it makes sense here to check the supported mask. If the card does not support vnicc at all, bridge commands are always allowed. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24s390/qeth: fix false reporting of VNIC CHAR config failureAlexandra Winter1-1/+0
Symptom: Error message "Configuring the VNIC characteristics failed" in dmesg whenever an OSA interface on z15 is set online. The VNIC characteristics get re-programmed when setting a L2 device online. This follows the selected 'wanted' characteristics - with the exception that the INVISIBLE characteristic unconditionally gets switched off. For devices that don't support INVISIBLE (ie. OSA), the resulting IO failure raises a noisy error message ("Configuring the VNIC characteristics failed"). For IQD, INVISIBLE is off by default anyways. So don't unnecessarily special-case the INVISIBLE characteristic, and thereby suppress the misleading error message on OSA devices. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24s390/qeth: lock the card while changing its hsuidJulian Wiedmann2-17/+28
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't take the conf_mutex to ensure that the card stays in this state while being reconfigured. Rework the code to take this lock, and drop a redundant state check in a helper function. Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24s390/qeth: fix qdio teardown after early init errorJulian Wiedmann3-14/+10
qeth_l?_set_online() goes through a number of initialization steps, and on any error uses qeth_l?_stop_card() to tear down the residual state. The first initialization step is qeth_core_hardsetup_card(). When this fails after having established a QDIO context on the device (ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't shut down this QDIO context again (since the card state hasn't progressed from DOWN at this stage). Even worse, we then call qdio_free() as final teardown step to free the QDIO data structures - while some of them are still hooked into wider QDIO infrastructure such as the IRQ list. This is inevitably followed by use-after-frees and other nastyness. Fix this by unconditionally calling qeth_qdio_clear_card() to shut down the QDIO context, and also to halt/clear any pending activity on the various IO channels. Remove the naive attempt at handling the teardown in qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it properly now in the wider teardown code. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24gtp: do not confirm neighbor when do pmtu updateHangbin Liu1-1/+1
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end, we should not call dst_confirm_neigh() as there is no two-way communication. Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not call dst_confirm_neigh(), we still set it to false to keep consistency with IPv6 code. v5: No change. v4: No change. v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24net: add bool confirm_neigh parameter for dst_ops.update_pmtuHangbin Liu1-1/+1
The MTU update code is supposed to be invoked in response to real networking events that update the PMTU. In IPv6 PMTU update function __ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor confirmed time. But for tunnel code, it will call pmtu before xmit, like: - tnl_update_pmtu() - skb_dst_update_pmtu() - ip6_rt_update_pmtu() - __ip6_rt_update_pmtu() - dst_confirm_neigh() If the tunnel remote dst mac address changed and we still do the neigh confirm, we will not be able to update neigh cache and ping6 remote will failed. So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we should not be invoking dst_confirm_neigh() as we have no evidence of successful two-way communication at this point. On the other hand it is also important to keep the neigh reachability fresh for TCP flows, so we cannot remove this dst_confirm_neigh() call. To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu to choose whether we should do neigh update or not. I will add the parameter in this patch and set all the callers to true to comply with the previous way, and fix the tunnel code one by one on later patches. v5: No change. v4: No change. v3: Do not remove dst_confirm_neigh, but add a new bool parameter in dst_ops.update_pmtu to control whether we should do neighbor confirm. Also split the big patch to small ones for each area. v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu. Suggested-by: David Miller <davem@davemloft.net> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-24net: dsa: bcm_sf2: Fix IP fragment location and behaviorFlorian Fainelli1-3/+3
The IP fragment is specified through user-defined field as the first bit of the first user-defined word. We were previously trying to extract it from the user-defined mask which could not possibly work. The ip_frag is also supposed to be a boolean, if we do not cast it as such, we risk overwriting the next fields in CFP_DATA(6) which would render the rule inoperative. Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-25spi: uniphier: Fix FIFO thresholdKunihiko Hayashi1-12/+19
Rx threshold means the value to inform the receiver when the number of words in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means the value to inform the sender when the number of words in Tx FIFO is equal to or less than the value. The controller triggers the driver to start the transfer. In case of Rx, the driver wants to detect that the specified number of words N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx, the driver wants to detect that the same number of spaces as Rx are in Tx FIFO, so the value of Tx threshold should be (FIFO size - N). For example, in order for the driver to receive at least 3 words from Rx FIFO, set 3 to Rx threshold. +-+-+-+-+-+-+-+-+ | | | | | |*|*|*| +-+-+-+-+-+-+-+-+ In order for the driver to send at least 3 words to Tx FIFO, because it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold. +-+-+-+-+-+-+-+-+ |*|*|*|*|*| | | | +-+-+-+-+-+-+-+-+ This adds new function uniphier_spi_set_fifo_threshold() to set threshold value to the register. And more, FIFO counts by 'words', so this renames 'fill_bytes' with 'fill_words', and fixes the calculation using bytes_per_words. Fixes: 37ffab817098 ("spi: uniphier: introduce polling mode") Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-12-23drm/i915: Hold reference to intel_frontbuffer as we track activityChris Wilson11-31/+116
Since obj->frontbuffer is no longer protected by the struct_mutex, as we are processing the execbuf, it may be removed. Mark the intel_frontbuffer as rcu protected, and so acquire a reference to the struct as we track activity upon it. Closes: https://gitlab.freedesktop.org/drm/intel/issues/827 Fixes: 8e7cb1799b4f ("drm/i915: Extract intel_frontbuffer active tracking") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218104043.3539458-1-chris@chris-wilson.co.uk (cherry picked from commit da42104f589d979bbe402703fd836cec60befae1) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2019-12-23drm/i915/gt: Ratelimit display power w/aChris Wilson1-1/+2
For very light workloads that frequently park, acquiring the display power well (required to prevent the dmc from trashing the system) takes longer than the execution. A good example is the igt_coherency selftest, which is slowed down by an order of magnitude in the worst case with powerwell cycling. To prevent frequent cycling, while keeping our fast soft-rc6, use a timer to delay release of the display powerwell. Fixes: 311770173fac ("drm/i915/gt: Schedule request retirement when timeline idles") References: https://gitlab.freedesktop.org/drm/intel/issues/848 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218093504.3477048-1-chris@chris-wilson.co.uk (cherry picked from commit 81ff52b705775433a955b2746d37b87bdc89a3d0) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2019-12-23drm/i915/pmu: Ensure monotonic rc6Tvrtko Ursulin2-54/+21
Avoid rc6 counter going backward in close to 0% RC6 scenarios like: 15.005477996 114,246,613 ns i915/rc6-residency/ 16.005876662 667,657 ns i915/rc6-residency/ 17.006131417 7,286 ns i915/rc6-residency/ 18.006615031 18,446,744,073,708,914,688 ns i915/rc6-residency/ 19.007158361 18,446,744,073,709,447,168 ns i915/rc6-residency/ 20.007806498 0 ns i915/rc6-residency/ 21.008227495 1,440,403 ns i915/rc6-residency/ There are two aspects to this fix. First is not assuming rc6 value zero means GT is asleep since that can also mean GPU is fully busy and we do not want to enter the estimation path in that case. Second is ensuring monotonicity on the estimation path itself. I suspect what is happening is with extremely rapid park/unpark cycles we get no updates on the real rc6 and therefore have to careful not to unconditionally trust use last known real rc6 when creating a new estimation. v2: * Simplify logic by not tracking the estimate but last reported value. Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: 16ffe73c186b ("drm/i915/pmu: Use GT parked for estimating RC6 while asleep") Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v1 Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20191217142057.1000-1-tvrtko.ursulin@linux.intel.com (cherry picked from commit df6a42053513846475ae1fbd224dfbdbcd0c7010) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2019-12-23dmaengine: virt-dma: Fix access after free in vchan_complete()Peter Ujfalusi1-2/+1
vchan_vdesc_fini() is freeing up 'vd' so the access to vd->tx_result is via already freed up memory. Move the vchan_vdesc_fini() after invoking the callback to avoid this. Fixes: 09d5b702b0f97 ("dmaengine: virt-dma: store result on dma descriptor") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20191220131100.21804-1-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-12-23dmaengine: k3dma: Avoid null pointer traversalJohn Stultz1-3/+9
In some cases we seem to submit two transactions in a row, which causes us to lose track of the first. If we then cancel the request, we may still get an interrupt, which traverses a null ds_run value. So try to avoid starting a new transaction if the ds_run value is set. While this patch avoids the null pointer crash, I've had some reports of the k3dma driver still getting confused, which suggests the ds_run/ds_done value handling still isn't quite right. However, I've not run into an issue recently with it so I think this patch is worth pushing upstream to avoid the crash. Signed-off-by: John Stultz <john.stultz@linaro.org> [add ss tag] Link: https://lore.kernel.org/r/20191218190906.6641-1-john.stultz@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-12-23PM / devfreq: tegra: Add COMMON_CLK dependencyArnd Bergmann1-0/+1
Compile-testing this driver fails if CONFIG_COMMON_CLK is not set: drivers/devfreq/tegra30-devfreq.o: In function `tegra_devfreq_target': tegra30-devfreq.c:(.text+0x164): undefined reference to `clk_set_min_rate' Fixes: 35f8dbc72721 ("PM / devfreq: tegra: Enable COMPILE_TEST for the driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
2019-12-23PM / devfreq: Drop explicit selection of PM_OPPLeonard Crestez1-4/+0
CONFIG_PM_OPP is already selected by CONFIG_PM_DEVFREQ since commit b9c69e043266 ("PM / devfreq: Add dependency on PM_OPP"). This means that individual drivers shouldn't "select PM_OPP" explicitly. Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> [cw00.choi: Edit the patch title] Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
2019-12-22Merge tag 'block-5.5-20191221' of git://git.kernel.dk/linux-blockLinus Torvalds5-27/+13
Pull block fixes from Jens Axboe: "Let's try this one again, this time without the compat_ioctl changes. We've got those fixed up, but that can go out next week. This contains: - block queue flush lockdep annotation (Bart) - Type fix for bsg_queue_rq() (Bart) - Three dasd fixes (Stefan, Jan) - nbd deadlock fix (Mike) - Error handling bio user map fix (Yang) - iocost fix (Tejun) - sbitmap waitqueue addition fix that affects the kyber IO scheduler (David)" * tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block: sbitmap: only queue kyber's wait callback if not already active block: fix memleak when __blk_rq_map_user_iov() is failed s390/dasd: fix typo in copyright statement s390/dasd: fix memleak in path handling error case s390/dasd/cio: Interpret ccw_device_get_mdc return value correctly block: Fix a lockdep complaint triggered by request queue flushing block: Fix the type of 'sts' in bsg_queue_rq() block: end bio with BLK_STS_AGAIN in case of non-mq devs and REQ_NOWAIT nbd: fix shutdown and recv work deadlock v2 iocost: over-budget forced IOs should schedule async delay
2019-12-22Merge tag 'riscv/for-v5.5-rc3' of ↵Linus Torvalds6-1/+194
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Paul Walmsley: "Several fixes, and one cleanup, for RISC-V. Fixes: - Fix an error in a Kconfig file that resulted in an undefined Kconfig option "CONFIG_CONFIG_MMU" - Fix undefined Kconfig option "CONFIG_CONFIG_MMU" - Fix scratch register clearing in M-mode (affects nommu users) - Fix a mismerge on my part that broke the build for CONFIG_SPARSEMEM_VMEMMAP users Cleanup: - Move SiFive L2 cache-related code to drivers/soc, per request" * tag 'riscv/for-v5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: move sifive_l2_cache.c to drivers/soc riscv: define vmemmap before pfn_to_page calls riscv: fix scratch register clearing in M-mode. riscv: Fix use of undefined config option CONFIG_CONFIG_MMU
2019-12-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds85-423/+723
Pull networking fixes from David Miller: 1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso, including adding a missing ipv6 match description. 2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi Bhat. 3) Fix uninit value in bond_neigh_init(), from Eric Dumazet. 4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold. 5) Fix use after free in tipc_disc_rcv(), from Tuong Lien. 6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul Chaignon. 7) Multicast MAC limit test is off by one in qede, from Manish Chopra. 8) Fix established socket lookup race when socket goes from TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening RCU grace period. From Eric Dumazet. 9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet. 10) Fix active backup transition after link failure in bonding, from Mahesh Bandewar. 11) Avoid zero sized hash table in gtp driver, from Taehee Yoo. 12) Fix wrong interface passed to ->mac_link_up(), from Russell King. 13) Fix DSA egress flooding settings in b53, from Florian Fainelli. 14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost. 15) Fix double free in dpaa2-ptp code, from Ioana Ciornei. 16) Reject invalid MTU values in stmmac, from Jose Abreu. 17) Fix refcount leak in error path of u32 classifier, from Davide Caratti. 18) Fix regression causing iwlwifi firmware crashes on boot, from Anders Kaseorg. 19) Fix inverted return value logic in llc2 code, from Chan Shu Tak. 20) Disable hardware GRO when XDP is attached to qede, frm Manish Chopra. 21) Since we encode state in the low pointer bits, dst metrics must be at least 4 byte aligned, which is not necessarily true on m68k. Add annotations to fix this, from Geert Uytterhoeven. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits) sfc: Include XDP packet headroom in buffer step size. sfc: fix channel allocation with brute force net: dst: Force 4-byte alignment of dst_metrics selftests: pmtu: fix init mtu value in description hv_netvsc: Fix unwanted rx_table reset net: phy: ensure that phy IDs are correctly typed mod_devicetable: fix PHY module format qede: Disable hardware gro when xdp prog is installed net: ena: fix issues in setting interrupt moderation params in ethtool net: ena: fix default tx interrupt moderation interval net/smc: unregister ib devices in reboot_event net: stmmac: platform: Fix MDIO init for platforms without PHY llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c) net: hisilicon: Fix a BUG trigered by wrong bytes_compl net: dsa: ksz: use common define for tag len s390/qeth: don't return -ENOTSUPP to userspace s390/qeth: fix promiscuous mode after reset s390/qeth: handle error due to unsupported transport mode cxgb4: fix refcount init for TC-MQPRIO offload tc-testing: initial tdc selftests for cls_u32 ...
2019-12-21pktcdvd: fix regression on 64-bit architecturesArnd Bergmann1-1/+1
The support for the compat ioctl did not actually do what it was supposed to do because of a typo, instead it broke native support for CDROM_LAST_WRITTEN and CDROM_SEND_PACKET on all architectures with CONFIG_COMPAT enabled. Fixes: 1b114b0817cc ("pktcdvd: add compat_ioctl handler") Signed-off-by: Arnd Bergmann <arnd@arndb.de> ---- Please apply for v5.5, I just noticed the regression while rebasing some of the patches I created on top. Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-12-21Merge tag 'for-linus-5.5b-rc3-tag' of ↵Linus Torvalds7-53/+73
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: "This contains two cleanup patches and a small series for supporting reloading the Xen block backend driver" * tag 'for-linus-5.5b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/grant-table: remove multiple BUG_ON on gnttab_interface xen-blkback: support dynamic unbind/bind xen/interface: re-define FRONT/BACK_RING_ATTACH() xenbus: limit when state is forced to closed xenbus: move xenbus_dev_shutdown() into frontend code... xen/blkfront: Adjust indentation in xlvbd_alloc_gendisk
2019-12-21Merge tag 'powerpc-5.5-4' of ↵Linus Torvalds2-16/+15
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "Two weeks worth of accumulated fixes: - A fix for a performance regression seen on PowerVM LPARs using dedicated CPUs, caused by our vcpu_is_preempted() returning true even for idle CPUs. - One of the ultravisor support patches broke KVM on big endian hosts in v5.4. - Our KUAP (Kernel User Access Prevention) code missed allowing access in __clear_user(), which could lead to an oops or erroneous SEGV when triggered via PTRACE_GETREGSET. - Two fixes for the ocxl driver, an open/remove race, and a memory leak in an error path. - A handful of other small fixes. Thanks to: Andrew Donnellan, Christian Zigotzky, Christophe Leroy, Christoph Hellwig, Daniel Axtens, David Hildenbrand, Frederic Barrat, Gautham R. Shenoy, Greg Kurz, Ihor Pasichnyk, Juri Lelli, Marcus Comstedt, Mike Rapoport, Parth Shah, Srikar Dronamraju, Vaidyanathan Srinivasan" * tag 'powerpc-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: KVM: PPC: Book3S HV: Fix regression on big endian hosts powerpc: Fix __clear_user() with KUAP enabled powerpc/pseries/cmm: fix managed page counts when migrating pages between zones powerpc/8xx: fix bogus __init on mmu_mapin_ram_chunk() ocxl: Fix potential memory leak on context creation powerpc/irq: fix stack overflow verification powerpc: Ensure that swiotlb buffer is allocated from low memory powerpc/shared: Use static key to detect shared processor powerpc/vcpu: Assume dedicated processors as non-preempt ocxl: Fix concurrent AFU open and device removal
2019-12-21Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds12-31/+56
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fixes from Stephen Boyd: "One core framework fix to walk the orphan list and match up clks to parents when clk providers register the DT provider after registering all their clks (as they should). Then a handful of driver fixes for the qcom, imx, and at91 drivers. The driver fixes are relatively small fixes for incorrect register settings or missing locks causing race conditions" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: qcom: Avoid SMMU/cx gdsc corner cases clk: qcom: gcc-sc7180: Fix setting flag for votable GDSCs clk: Move clk_core_reparent_orphans() under CONFIG_OF clk: at91: fix possible deadlock clk: walk orphan list on clock provider registration clk: imx: pll14xx: fix clk_pll14xx_wait_lock clk: imx: clk-imx7ulp: Add missing sentinel of ulp_div_table clk: imx: clk-composite-8m: add lock to gate/mux
2019-12-20sfc: Include XDP packet headroom in buffer step size.Charles McLachlan1-7/+7
Correct a mismatch between rx_page_buf_step and the actual step size used when filling buffer pages. This patch fixes the page overrun that occured when the MTU was set to anything bigger than 1692. Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20sfc: fix channel allocation with brute forceEdward Cree2-22/+19
It was possible for channel allocation logic to get confused between what it had and what it wanted, and end up trying to use the same channel for both PTP and regular TX. This led to a kernel panic: BUG: unable to handle page fault for address: 0000000000047635 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] SMP PTI CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.4.0-rc3-ehc14+ #900 Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013 RIP: 0010:native_queued_spin_lock_slowpath+0x188/0x1e0 Code: f3 90 48 8b 32 48 85 f6 74 f6 eb e8 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 05 48 63 f6 48 05 c0 98 02 00 48 03 04 f5 a0 c6 ed 81 <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 32 RSP: 0018:ffffc90000003d28 EFLAGS: 00010006 RAX: 0000000000047635 RBX: 0000000000000246 RCX: 0000000000040000 RDX: ffff888627a298c0 RSI: 0000000000003ffe RDI: ffff88861f6b8dd4 RBP: ffff8886225c6e00 R08: 0000000000040000 R09: 0000000000000000 R10: 0000000616f080c6 R11: 00000000000000c0 R12: ffff88861f6b8dd4 R13: ffffc90000003dc8 R14: ffff88861942bf00 R15: ffff8886150f2000 FS: 0000000000000000(0000) GS:ffff888627a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000047635 CR3: 000000000200a000 CR4: 00000000000006f0 Call Trace: <IRQ> _raw_spin_lock_irqsave+0x22/0x30 skb_queue_tail+0x1b/0x50 sock_queue_err_skb+0x9d/0xf0 __skb_complete_tx_timestamp+0x9d/0xc0 efx_dequeue_buffer+0x126/0x180 [sfc] efx_xmit_done+0x73/0x1c0 [sfc] efx_ef10_ev_process+0x56a/0xfe0 [sfc] ? tick_sched_do_timer+0x60/0x60 ? timerqueue_add+0x5d/0x70 ? enqueue_hrtimer+0x39/0x90 efx_poll+0x111/0x380 [sfc] ? rcu_accelerate_cbs+0x50/0x160 net_rx_action+0x14a/0x400 __do_softirq+0xdd/0x2d0 irq_exit+0xa0/0xb0 do_IRQ+0x53/0xe0 common_interrupt+0xf/0xf </IRQ> In the long run we intend to rewrite the channel allocation code, but for 'net' fix this by allocating extra_channels, and giving them TX queues, even if we do not in fact need them (e.g. on NICs without MAC TX timestamping), and thereby using simpler logic to assign the channels once they're allocated. Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20hv_netvsc: Fix unwanted rx_table resetHaiyang Zhang3-6/+11
In existing code, the receive indirection table, rx_table, is in struct rndis_device, which will be reset when changing MTU, ringparam, etc. User configured receive indirection table values will be lost. To fix this, move rx_table to struct net_device_context, and check netif_is_rxfh_configured(), so rx_table will be set to default only if no user configured value. Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: phy: ensure that phy IDs are correctly typedRussell King1-4/+4
PHY IDs are 32-bit unsigned quantities. Ensure that they are always treated as such, and not passed around as "int"s. Fixes: 13d0ab6750b2 ("net: phy: check return code when requesting PHY driver module") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20qede: Disable hardware gro when xdp prog is installedManish Chopra1-2/+2
commit 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") introduced a regression in driver that when xdp program is installed on qede device, device's aggregation feature (hardware GRO) is not getting disabled, which is unexpected with xdp. Fixes: 18c602dee472 ("qede: Use NETIF_F_GRO_HW.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: ena: fix issues in setting interrupt moderation params in ethtoolArthur Kiyanovski1-14/+10
Issue 1: -------- Reproduction steps: 1. sudo ethtool -C eth0 rx-usecs 128 2. sudo ethtool -C eth0 adaptive-rx on 3. sudo ethtool -C eth0 adaptive-rx off 4. ethtool -c eth0 expected output: rx-usecs 128 actual output: rx-usecs 0 Reason for issue: In stage 3, ethtool userspace calls first the ena_get_coalesce() handler to get the current value of all properties, and then the ena_set_coalesce() handler. When ena_get_coalesce() is called the adaptive interrupt moderation is still on. There is an if in the code that returns the rx_coalesce_usecs only if the adaptive interrupt moderation is off. And since it is still on, rx_coalesce_usecs is not set, meaning it stays 0. Solution to issue: Remove this if static interrupt moderation intervals have nothing to do with dynamic ones. Issue 2: -------- Reproduction steps: 1. sudo ethtool -C eth0 adaptive-rx on 2. sudo ethtool -C eth0 rx-usecs 128 3. ethtool -c eth0 expected output: rx-usecs 128 actual output: rx-usecs 0 Reason for issue: In stage 2, when ena_set_coalesce() is called, the handler tests if rx adaptive interrupt moderation is on, and if it is, it returns before getting to the part in the function that sets the rx non-adaptive interrupt moderation interval. Solution to issue: Remove the return from the function when rx adaptive interrupt moderation is on. Also cleaned up the fixed code in ena_set_coalesce by grouping together adaptive interrupt moderation toggling, and using && instead of nested ifs. Fixes: b3db86dc4b82 ("net: ena: reimplement set/get_coalesce()") Fixes: 0eda847953d8 ("net: ena: fix retrieval of nonadaptive interrupt moderation intervals") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-20net: ena: fix default tx interrupt moderation intervalArthur Kiyanovski1-1/+1
Current default non-adaptive tx interrupt moderation interval is 196 us. This value is too high and might cause the tx queue to fill up. In this commit we set the default non-adaptive tx interrupt moderation interval to 64 us in order to: 1. Reduce the probability of the queue filling-up (when compared to the current default value of 196 us). 2. Reduce unnecessary tx interrupt overhead (which happens if we set the default tx interval to 0). We determined experimentally that 64 us is an optimal value that reduces interrupt rate by more than 20% without affecting performance. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-02-24 20:33:06 +0000