Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix the throttle IRQ handling during cpufreq initialization on
Qualcomm platforms (Bjorn Andersson)"
* tag 'pm-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-hw: Delay enabling throttle_irq
cpufreq: Reintroduce ready() callback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.17-rc6 for reported issues.
The majority of these are IIO fixes for small things, and the other
two are a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
iio: Fix error handling for PM
iio: addac: ad74413r: correct comparator gpio getters mask usage
iio: addac: ad74413r: use ngpio size when iterating over mask
iio: addac: ad74413r: Do not reference negative array offsets
iio: adc: men_z188_adc: Fix a resource leak in an error handling path
iio: frequency: admv1013: remove the always true condition
iio: accel: fxls8962af: add padding to regmap for SPI
iio:imu:adis16480: fix buffering for devices with no burst mode
iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
iio: adc: tsc2046: fix memory corruption by preventing array overflow
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core fix for 5.17-rc6. It resolves a reported
problem when the DMA map of a device is not properly released.
It has been in linux-next with no reported problems"
* tag 'driver-core-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Free DMA range map when device is released
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 5.17-rc6.
It resolves a reported problem in the fbtft fb_st7789v.c driver that
could cause the display to be flipped in cold weather.
It has been in linux-next with no reported problems"
* tag 'staging-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fbtft: fb_st7789v: reset display before initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small n_gsm and sc16is7xx serial driver fixes for
5.17-rc6.
The n_gsm fixes are from Siemens as it seems they are using the line
discipline and fixing up a number of issues they found in their
testing. The sc16is7xx serial driver fix is for a reported problem
with that chip.
All of these have been in linux-next with no reported problems"
* tag 'tty-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: Fix for incorrect data being transmitted
tty: n_gsm: fix deadlock in gsmtty_open()
tty: n_gsm: fix wrong modem processing in convergence layer type 2
tty: n_gsm: fix wrong tty control line for flow control
tty: n_gsm: fix NULL pointer access due to DLCI release
tty: n_gsm: fix proper link termination after failed open
tty: n_gsm: fix encoding of command/response bit
tty: n_gsm: fix encoding of control signal octet bit DV
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.17-rc6 to resolve
reported problems and add new device ids. They include:
- dwc3:
- device mapping fix
- new device ids
- driver fixes
- xhci driver fixes
- gadget driver fixes
- usb-serial driver device id updates
All of these have been in linux-next with no reported problems"
* tag 'usb-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: rndis: add spinlock for rndis response list
usb: dwc3: gadget: Let the interrupt handler disable bottom halves.
USB: gadget: validate endpoint index for xilinx udc
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
usb: dwc2: drd: fix soft connect when gadget is unconfigured
usb: dwc3: pci: Fix Bay Trail phy GPIO mappings
tps6598x: clear int mask on probe failure
xhci: Prevent futile URB re-submissions due to incorrect return value.
xhci: re-initialize the HC during resume if HCE was set
usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail
usb: dwc3: pci: add support for the Intel Raptor Lake-S
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Two fixes for the pata_hpt37x driver, both from Sergey:
- Fix a PCI register access using an incorrect size (8bits instead of
16bits)
- Make sure to always disable the primary channel as it is unused"
* tag 'ata-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_hpt37x: disable primary channel on HPT371
ata: pata_hpt37x: fix PCI clock detection
|
|
The code uses uart_amba_port::port on many places. Sometimes it even
needs not uart_amba_port itself. So simplify the code on many places
and remove the need of uart_amba_port on some places completely.
No functional changes intended. The objdump -d output shows only a code
move in pl010_rx_chars().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220224111028.20917-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of open-coding what serial_lpc32xx_stop_tx() already does, call
it in __serial_lpc32xx_tx() directly.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the hello print among with version and name definitions. Drivers
should print nothing if they are successful.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All these return bitmasks, so it makes more sense to return unsigned --
this is what a reader and also all the callers expect.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 9a1870ce812e ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf3dc1 ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223151240.70248-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 90b9aacf912a ("serial: 8250_pci: add Intel Tangier support")
Fixes: f549e94effa1 ("serial: 8250_pci: add Intel Penwell ports")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Depends-on: d9eda9bab237 ("serial: 8250_pci: Intel MID UART support to its own driver")
Link: https://lore.kernel.org/r/20220215100920.41984-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
coccinelle report:
./drivers/tty/serial/8250/8250_aspeed_vuart.c:85:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:174:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:127:8-16:
WARNING: use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Link: https://lore.kernel.org/r/fed40753603dac4d14b17970c88e6f5f936348c1.1644541843.git.yang.guang5@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Correct the Kconfig help text for SERIAL_8250_LPSS, SERIAL_8250_MID and
SERIAL_8250_PERICOM configuration options for dedicated PCI UART drivers
that have been blacklisted in the generic PCI 8250 UART driver and as
from commit a13e19cf3dc10 ("serial: 8250_lpss: split LPSS driver to
separate module"), commit d9eda9bab2372 ("serial: 8250_pci: Intel MID
UART support to its own driver"), and commit fcfd3c09f4078 ("serial:
8250_pci: Split out Pericom driver") respectively are not handled by
said driver anymore (rather than for extra features only, as the current
text indicates), and therefore require the respective dedicated drivers
to work at all.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2202121704560.34636@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement simple usage of fractional divisor. When main divisor D is too
large to represent requested baudrate then use divisor M from the
fractional divisor feature. All the M prescalers are set to the same and
maximal value 63, so the fractional part of the fractional divisor is not
used at all. We also determine upper limit for possible baudrates.
Experiments show that UART at baudrate 1500000 Bd with this configuration
is stable. So there is no need to implement complicated calculation of
fractional coefficients yet.
To use this feature with higher baudrates, it is required to use UART clock
provided by UART clock driver. Default boot xtal clock is not capable of
higher baudrates.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-6-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement a new device driver for controlling UART clocks on Marvell
Armada 3700 SoC. This device driver is loaded for devices which match
the compatible string "marvell,armada-3700-uart-clock".
There are more pitfalls related to UART clocks:
- both UARTs use same parent clock source (which can be xtal or one of
the TBG clocks),
- if a TBG clock is used as the parent clock, there are two additional
divisors that can both be configured to divide the rate by 1, 2, ... 6,
but these divisors are again shared between the two UART controllers
on the SOC,
- the configuration of the parent clock source and divisors is done in
the address space of the first UART controller, UART1. Clocks can be
gated separately for UART1 and UART2, but this setting also lives in
the address space of UART1,
- Marvell's Functional Specification for Armada 3720 document has the
clock gating bits swapped, so the one described to gate UART1 clock
actually gates UART2 and vice versa,
- each UART has it's own "special divisor", and this uses the parent
clock described above. These divisors are configure in each UART's
address space separately.
Thus the driver for UART2 controller needs to have access to UART1
address space, since UART1 address space contains some bits exclusive
for UART2 and also some bits which are shared between UART1 and UART2.
Also, during boot, when early console is active on one of the UARTs,
and we want to switch parent clock from xtal (default) to TBG (to be
more flexible with baudrates), the driver changing UART clocks also
needs to be able to change the "special divisor", so that the baudrate
of earlycon is not changed when swtiching to normal console. Thus the
clock driver also needs to be able to access UART2 register space,
for UART2's "special divisor".
For these reasons, this new UART clock driver does not use
ioremap_resource(), but only ioremap() to prevent resource conflicts
between UART clock driver and UART driver.
We need to share only two 32-bit registers between the UART driver and
the UART clock driver:
- UART Clock Control
- UART 2 Baud Rate Divisor
Access to these two registers are protected by one spinlock to prevent
any conflicts. Access is required only during probing, when changing
baudrate or during suspend/resume.
Hardware can be configured to use one of following clocks as UART parent
clock: TBG-A-P, TBG-B-P, TBG-A-S, TBG-B-S, xtal. Not every clock is
usable for higher buadrates. Any subset can be specified in the
device-tree and the driver will choose the best one which also still
supports the mandatory baudrate of 9600 Bd. For smooth boot log output
it is needed to specify clock used by early console, otherwise garbage
would be printed on UART during probe of UART clock driver and
transitioning from early console to normal console.
We are implementing this to be able to configure TBG clock as UART
parent clock, which is required to be able to achieve higher baudrates
than 230400 Bd. We achieve this by referencing this new UART clock
device node in UART's device node. UART clock device driver
automatically chooses the best clock source for UART driver.
Until now, UART's device-tree node needed to reference one of the static
clocks (xtal or one of the TBGs) as parent clock in the `clocks`
phandle - the parent clock which was configured before booting the
kernel. If bootloader changed UART's parent clock, it needed to change
the `clocks` phandle in DTB correspondingly before booting.
From now on both the old mechanism (xtal or TBG referenced as parent
clock in `clocks` phandle) and the new one (UART clock referenced in the
`clocks` phandle) are supported, to provide full backward compatibility
with existing DTS files, full backward compatibility with existing boot
loaders, and to provide new features (runtime clock configuration to
allow higher baudrates than 230400 Bd). New features are available only
with new DTS files.
There was also a discussion about how the UART node and the
clock-controller node could be wrapped together in a new binding [1, 2].
As explained there, this is not possible if we want to keep backwards
compatibility with existing bootloaders, and thus we are doing this by
putting the UART clock-controller node inside the UART1 node.
[1] https://lore.kernel.org/linux-serial/20220120000651.in7s6nazif5qjkme@pali/
[2] https://lore.kernel.org/linux-serial/20220125204006.A6D09C340E0@smtp.kernel.org/
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-4-kabel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Export only the GPIOs that are not shared with hardware modem control
lines. Introduce new device parameter indicating whether modem control
lines are available.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-4-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
RTS, DTR and LOOP bits can be updated in a single MCR register update.
This reduces the number of (slow) SPI/I2C bus transactions.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-3-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Preserve unaffected bits state when accessing EFR register. This
prevents hardware flow control bits from being cleared on enhanced
functions access.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-2-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't start the whole chain for TX if there is no data to send. This is
mostly relevant for rs485 mode as there might be rts-before-send and
rts-after-send delays involved.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220217211839.443039-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple driver fixes in the clk subsystem
- Fix a hang due to bad clk parent in the Ingenic jz4725b driver
- Fix SD controllers on Qualcomm MSM8994 SoCs by removing clks that
shouldn't be touched"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: jz4725b: fix mmc0 clock gating
clk: qcom: gcc-msm8994: Remove NoC clocks
|
|
Pull drm fixes from Dave Airlie:
"Regular drm fixes pull, i915, amdgpu and tegra mostly, all pretty
small.
core:
- edid: Always set RGB444
tegra:
- tegra186 suspend/resume fixes
- syncpoint wait fix
- build warning fix
- eDP on older devices fix
amdgpu:
- Display FP fix
- PCO powergating fix
- RDNA2 OEM SKU stability fixes
- Display PSR fix
- PCI ASPM fix
- Display link encoder fix for TEST_COMMIT
- Raven2 suspend/resume fix
- Fix a regression in virtual display support
- GPUVM eviction fix
i915:
- Fix QGV handling on ADL-P+
- Fix bw atomic check when switching between SAGV vs. no SAGV
- Disconnect PHYs left connected by BIOS on disabled ports
- Fix SAVG to no SAGV transitions on TGL+
- Print PHY name properly on calibration error (DG2)
imx:
- dcss: Select GEM CMA helpers
radeon:
- Fix some variables's type
vc4:
- Fix codec cleanup
- Fix PM reference counting"
* tag 'drm-fixes-2022-02-25' of git://anongit.freedesktop.org/drm/drm: (24 commits)
drm/amdgpu: check vm ready by amdgpu_vm->evicting flag
drm/amdgpu: bypass tiling flag check in virtual display case (v2)
Revert "drm/amdgpu: add modifiers in amdgpu_vkms_plane_init()"
drm/amdgpu: do not enable asic reset for raven2
drm/amd/display: Fix stream->link_enc unassigned during stream removal
drm/amd: Check if ASPM is enabled from PCIe subsystem
drm/edid: Always set RGB444
drm/tegra: dpaux: Populate AUX bus
drm/radeon: fix variable type
drm/amd/display: For vblank_disable_immediate, check PSR is really used
drm/amd/pm: fix some OEM SKU specific stability issues
drm/amdgpu: disable MMHUB PG for Picasso
drm/amd/display: Protect update_bw_bounding_box FPU code.
drm/i915/dg2: Print PHY name properly on calibration error
drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV
drm/i915: Correctly populate use_sagv_wm for all pipes
drm/i915: Disconnect PHYs left connected by BIOS on disabled ports
drm/i915: Widen the QGV point mask
drm/imx/dcss: i.MX8MQ DCSS select DRM_GEM_CMA_HELPER
drm/vc4: crtc: Fix runtime_pm reference counting
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Fix a merge error that broke PCI device enumeration on mvebu
platforms, including Turris Omnia (Armada 385) (Pali Rohár)
- Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
VBIOSes don't account for "harvested" (disabled) parts of the chip
when initializing caches (Alex Deucher)
* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
PCI: mvebu: Fix device enumeration regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
Current release - regressions:
- bpf: fix crash due to out of bounds access into reg2btf_ids
- mvpp2: always set port pcs ops, avoid null-deref
- eth: marvell: fix driver load from initrd
- eth: intel: revert "Fix reset bw limit when DCB enabled with 1 TC"
Current release - new code bugs:
- mptcp: fix race in overlapping signal events
Previous releases - regressions:
- xen-netback: revert hotplug-status changes causing devices to not
be configured
- dsa:
- avoid call to __dev_set_promiscuity() while rtnl_mutex isn't
held
- fix panic when removing unoffloaded port from bridge
- dsa: microchip: fix bridging with more than two member ports
Previous releases - always broken:
- bpf:
- fix crash due to incorrect copy_map_value when both spin lock
and timer are present in a single value
- fix a bpf_timer initialization issue with clang
- do not try bpf_msg_push_data with len 0
- add schedule points in batch ops
- nf_tables:
- unregister flowtable hooks on netns exit
- correct flow offload action array size
- fix a couple of memory leaks
- vsock: don't check owner in vhost_vsock_stop() while releasing
- gso: do not skip outer ip header in case of ipip and net_failover
- smc: use a mutex for locking "struct smc_pnettable"
- openvswitch: fix setting ipv6 fields causing hw csum failure
- mptcp: fix race in incoming ADD_ADDR option processing
- sysfs: add check for netdevice being present to speed_show
- sched: act_ct: fix flow table lookup after ct clear or switching
zones
- eth: intel: fixes for SR-IOV forwarding offloads
- eth: broadcom: fixes for selftests and error recovery
- eth: mellanox: flow steering and SR-IOV forwarding fixes
Misc:
- make __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor
friends not report freed skbs as drops
- force inlining of checksum functions in net/checksum.h"
* tag 'net-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
net: mv643xx_eth: process retval from of_get_mac_address
ping: remove pr_err from ping_lookup
Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
openvswitch: Fix setting ipv6 fields causing hw csum failure
ipv6: prevent a possible race condition with lifetimes
net/smc: Use a mutex for locking "struct smc_pnettable"
bnx2x: fix driver load from initrd
Revert "xen-netback: Check for hotplug-status existence before watching"
Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
net/mlx5e: Fix VF min/max rate parameters interchange mistake
net/mlx5e: Add missing increment of count
net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
net/mlx5e: Add feature check for set fec counters
net/mlx5e: TC, Skip redundant ct clear actions
net/mlx5e: TC, Reject rules with forward and drop actions
net/mlx5e: TC, Reject rules with drop and modify hdr action
net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
net/mlx5: Fix possible deadlock on rule deletion
...
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix QGV handling on ADL-P+ (Ville Syrjälä)
- Fix bw atomic check when switching between SAGV vs. no SAGV (Ville Syrjälä)
- Disconnect PHYs left connected by BIOS on disabled ports (Imre Deak)
- Fix SAVG to no SAGV transitions on TGL+ (Ville Syrjälä)
- Print PHY name properly on calibration error (DG2) (Matt Roper)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YhdyHwRWkOTWwlqi@tursulin-mobl2
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request:
- send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
- fix passthrough to namespaces with unsupported features (Christoph
Hellwig)
- Clear iocb->private at poll completion (Stefano)
* tag 'block-5.17-2022-02-24' of git://git.kernel.dk/linux-block:
nvme-tcp: send H2CData PDUs based on MAXH2CDATA
nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
nvme: don't return an error from nvme_configure_metadata
block: clear iocb->private in blkdev_bio_end_io_async()
|
|
It is easy to hit the below memory leaks in my TigerLake platform:
unreferenced object 0xffff927c8b91dbc0 (size 32):
comm "kworker/0:2", pid 112, jiffies 4294893323 (age 83.604s)
hex dump (first 32 bytes):
4e 41 4d 45 3d 49 4e 54 33 34 30 30 20 54 68 65 NAME=INT3400 The
72 6d 61 6c 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 rmal.kkkkkkkkkk.
backtrace:
[<ffffffff9c502c3e>] __kmalloc_track_caller+0x2fe/0x4a0
[<ffffffff9c7b7c15>] kvasprintf+0x65/0xd0
[<ffffffff9c7b7d6e>] kasprintf+0x4e/0x70
[<ffffffffc04cb662>] int3400_notify+0x82/0x120 [int3400_thermal]
[<ffffffff9c8b7358>] acpi_ev_notify_dispatch+0x54/0x71
[<ffffffff9c88f1a7>] acpi_os_execute_deferred+0x17/0x30
[<ffffffff9c2c2c0a>] process_one_work+0x21a/0x3f0
[<ffffffff9c2c2e2a>] worker_thread+0x4a/0x3b0
[<ffffffff9c2cb4dd>] kthread+0xfd/0x130
[<ffffffff9c201c1f>] ret_from_fork+0x1f/0x30
Fix it by calling kfree() accordingly.
Fixes: 38e44da59130 ("thermal: int3400_thermal: process "thermal table changed" event")
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull ARM cpufreq fixes for 5.18-rc6 from Viresh Kumar:
"This fixes issues related to throttle IRQ for Qcom SoCs."
* 'cpufreq/arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: qcom-hw: Delay enabling throttle_irq
cpufreq: Reintroduce ready() callback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull more x86 platform driver fixes from Hans de Goede:
"Two more fixes:
- Fix suspend/resume regression on AMD Cezanne APUs in >= 5.16
- Fix Microsoft Surface 3 battery readings"
* tag 'platform-drivers-x86-v5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
surface: surface3_power: Fix battery readings on batteries without a serial number
platform/x86: amd-pmc: Set QOS during suspend on CZN w/ timer wakeup
|
|
Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.
It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.
Fixes: 76723bca2802 ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.
Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to configure TC map 0 for VSI 391
This reverts commit 3d2504663c41104b4359a15f35670cfa82de1bbf.
Fixes: 3d2504663c41 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 2afeec08ab5c86ae21952151f726bfe184f6b23d.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 1f2565780e9b7218cf92c7630130e82dcc0fe9c2.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.17-rc6
Here's a revert of a commit which erroneously added a device id used for
the EPP/MEM mode of ch341 devices.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.17-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
|
|
number
The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.
This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.
Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.
Fixes: b1f81b496b0d ("platform/x86: surface3_power: MSHW0011 rev-eng implementation")
BugLink: https://github.com/linux-surface/linux-surface/issues/608
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220224101848.7219-1-hdegoede@redhat.com
|
|
commit 59348401ebed ("platform/x86: amd-pmc: Add special handling for
timer based S0i3 wakeup") adds support for using another platform timer
in lieu of the RTC which doesn't work properly on some systems. This path
was validated and worked well before submission. During the 5.16-rc1 merge
window other patches were merged that caused this to stop working properly.
When this feature was used with 5.16-rc1 or later some OEM laptops with the
matching firmware requirements from that commit would shutdown instead of
program a timer based wakeup.
This was bisected to commit 8d89835b0467 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). This wasn't supposed to cause any
negative impacts and also tested well on both Intel and ARM platforms.
However this changed the semantics of when CPUs are allowed to be in the
deepest state. For the AMD systems in question it appears this causes a
firmware crash for timer based wakeup.
It's hypothesized to be caused by the `amd-pmc` driver sending `OS_HINT`
and all the CPUs going into a deep state while the timer is still being
programmed. It's likely a firmware bug, but to avoid it don't allow setting
CPUs into the deepest state while using CZN timer wakeup path.
If later it's discovered that this also occurs from "regular" suspends
without a timer as well or on other silicon, this may be later expanded to
run in the suspend path for more scenarios.
Cc: stable@vger.kernel.org # 5.16+
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/linux-acpi/BL1PR12MB51570F5BD05980A0DCA1F3F4E23A9@BL1PR12MB5157.namprd12.prod.outlook.com/T/#mee35f39c41a04b624700ab2621c795367f19c90e
Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Fixes: 23f62d7ab25b ("PM: sleep: Pause cpuidle later and resume it earlier during system transitions")
Fixes: 59348401ebed ("platform/x86: amd-pmc: Add special handling for timer based S0i3 wakeup"
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220223175237.6209-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.
[ 361.894299] [1: irq/191-dwc3:16979] list_add corruption.
next->prev should be prev (ffffff80651764d0),
but was ffffff883dc36f80. (next=ffffff80651764d0).
[ 361.904380] [1: irq/191-dwc3:16979] Call trace:
[ 361.904391] [1: irq/191-dwc3:16979] __list_add_valid+0x74/0x90
[ 361.904401] [1: irq/191-dwc3:16979] rndis_msg_parser+0x168/0x8c0
[ 361.904409] [1: irq/191-dwc3:16979] rndis_command_complete+0x24/0x84
[ 361.904417] [1: irq/191-dwc3:16979] usb_gadget_giveback_request+0x20/0xe4
[ 361.904426] [1: irq/191-dwc3:16979] dwc3_gadget_giveback+0x44/0x60
[ 361.904434] [1: irq/191-dwc3:16979] dwc3_ep0_complete_data+0x1e8/0x3a0
[ 361.904442] [1: irq/191-dwc3:16979] dwc3_ep0_interrupt+0x29c/0x3dc
[ 361.904450] [1: irq/191-dwc3:16979] dwc3_process_event_entry+0x78/0x6cc
[ 361.904457] [1: irq/191-dwc3:16979] dwc3_process_event_buf+0xa0/0x1ec
[ 361.904465] [1: irq/191-dwc3:16979] dwc3_thread_interrupt+0x34/0x5c
Fixes: f6281af9d62e ("usb: gadget: rndis: use list_for_each_entry_safe")
Cc: stable <stable@kernel.org>
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1645507768-77687-1-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e7b0 ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Assure that host may not manipulate the index to point
past endpoint array.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.17-2022-02-23:
amdgpu:
- Display FP fix
- PCO powergating fix
- RDNA2 OEM SKU stability fixes
- Display PSR fix
- PCI ASPM fix
- Display link encoder fix for TEST_COMMIT
- Raven2 suspend/resume fix
- Fix a regression in virtual display support
- GPUVM eviction fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223214623.28823-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/drm/tegra into drm-fixes
drm/tegra: Fixes for v5.17-rc6
Contains a couple of fixes for Tegra186 suspend/resume, syncpoint
waiting, a build warning and eDP on older Tegra devices.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223161903.293392-1-thierry.reding@gmail.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* edid: Always set RGB444
* imx/dcss: Select GEM CMA helpers
* radeon: Fix some variables's type
* vc4: Fix codec cleanup; Fix PM reference counting
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YhaKj4zWJ42YWRts@linux-uq9g.fritz.box
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Update some maintainers email addresses
- Fix handling of elfcorehdr reservation for crash dump kernel
- Fix unittest expected warnings text
* tag 'devicetree-fixes-for-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: update Roger Quadros email
MAINTAINERS: sifive: drop Yash Shah
of/fdt: move elfcorehdr reservation early for crash dump kernel
of: unittest: update text of expected warnings
|
|
The VF min and max rate were passed incorrectly and resulted in wrongly
interchanging them. Fix the order of parameters in
mlx5_esw_qos_set_vport_rate().
Fixes: d7df09f5e7b4 ("net/mlx5: E-switch, Enable vport QoS on demand")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add mistakenly missing increment of count variable when looping over
output buffer in mlx5e_self_test().
This resolves the issue of garbage values output when querying with self
test via ethtool.
before:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 1768697188
Health Test 758528120
Loopback Test 3288687
after:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 0
Health Test 0
Loopback Test 0
Fixes: 7990b1b5e8bd ("net/mlx5e: loopback test is not supported in switchdev mode")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.
Fix by returning error in case flow is matching on tunnel key.
Fixes: 72046a91d134 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.
Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.
Fixes: f828ca6a2fb6 ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.
Fixes: 0a1498ebfa55 ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|