| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).
We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().
Also changed the comment to be more informative while we are touching this
code.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The bt_* printk macros include a \n already, so we don't need extra ones
here.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:
1) A non functioning BT HCI getting registered
2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.
This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case of hci send frame failure, skb is still owned
by the caller (hci_core) and then should not be freed.
This fixes crash on dragonboard-410c when sending SCO
packet. skb is freed by both btqcomsmd and hci_core.
Fixes: 1511cc750c3d ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
John Stultz reports a boot time crash with the HiKey board (which uses
hci_serdev) occurring in hci_uart_tx_wakeup(). That function is
contained in hci_ldisc.c, but also called from the newer hci_serdev.c.
It acquires the proto_lock in struct hci_uart and it turns out that we
forgot to init the lock in the serdev code path, thus causing the crash.
John bisected the crash to commit 67d2f8781b9f ("Bluetooth: hci_ldisc:
Allow sleeping while proto locks are held"), but the issue was present
before and the commit merely exposed it. (Perhaps by luck, the crash
did not occur with rwlocks.)
Init the proto_lock in the serdev code path to avoid the oops.
Stack trace for posterity:
Unable to handle kernel read from unreadable memory at 406f127000
[000000406f127000] user address but active_mm is swapper
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Hardware name: HiKey Development Board (DT)
Call trace:
hci_uart_tx_wakeup+0x38/0x148
hci_uart_send_frame+0x28/0x38
hci_send_frame+0x64/0xc0
hci_cmd_work+0x98/0x110
process_one_work+0x134/0x330
worker_thread+0x130/0x468
kthread+0xf8/0x128
ret_from_fork+0x10/0x18
Link: https://lkml.org/lkml/2017/11/15/908
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Cc: Ronald Tschalär <ronald@innovation.ch>
Cc: Rob Herring <rob.herring@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fix: drivers/bluetooth/Kconfig:35:warning: multi-line strings not
supported warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.
Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).
The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.
Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.
This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch :0x00000111
hci0: ROM :0x00000302
hci0: SOC :0x00000044
Since there is no rampatch for this controller revision, just make
it work as is.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete match field defines that are not supported at this time.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.
'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -
ip netns add ns1
ip link add ve1 type veth peer name ve2
ip link add link ve2 name iv1 type ipvlan mode l2
ip link set dev iv1 netns ns1
ip link set ve1 up
ip link set ve2 up
ip -n ns1 link set iv1 up
ip addr add 192.168.10.1/24 dev ve1
ip -n ns1 addr 192.168.10.2/24 dev iv1
ping -c2 192.168.10.2
<Works!>
ip neigh show dev ve1
ip neigh show 192.168.10.2 lladdr <random> dev ve1
ping -c2 192.168.10.2
<Still works! Wrong!!>
This patch adds that missing check in the IPvlan rx-handler.
Reported-by: Amit Sikka <amit.sikka@ericsson.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflict was two parallel additions of include files to sch_generic.c,
no biggie.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixes for the media subsytem:
- The largest amount of fixes in this series is with regards to
comments that aren't kernel-doc, but start with "/**".
A new check added for 4.15 makes it to produce a *huge* amount of
new warnings (I'm compiling here with W=1). Most of the patches in
this series fix those.
No code changes - just comment changes at the source files
- rc: some fixed in order to better handle RC repetition codes
- v4l-async: use the v4l2_dev from the root notifier when matching
sub-devices
- v4l2-fwnode: Check subdev count after checking port
- ov 13858 and et8ek8: compilation fix with randconfigs
- usbtv: a trivial new USB ID addition
- dibusb-common: don't do DMA on stack on firmware load
- imx274: Fix error handling, add MAINTAINERS entry
- sir_ir: detect presence of port"
* tag 'media/v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (50 commits)
media: imx274: Fix error handling, add MAINTAINERS entry
media: v4l: async: use the v4l2_dev from the root notifier when matching sub-devices
media: v4l2-fwnode: Check subdev count after checking port
media: et8ek8: select V4L2_FWNODE
media: ov13858: Select V4L2_FWNODE
media: rc: partial revert of "media: rc: per-protocol repeat period"
media: dvb: i2c transfers over usb cannot be done from stack
media: dvb-frontends: complete kernel-doc markups
media: docs: add documentation for frontend attach info
media: dvb_frontends: fix kernel-doc macros
media: drivers: remove "/**" from non-kernel-doc comments
media: lm3560: add a missing kernel-doc parameter
media: rcar_jpu: fix two kernel-doc markups
media: vsp1: add a missing kernel-doc parameter
media: soc_camera: fix a kernel-doc markup
media: mt2063: fix some kernel-doc warnings
media: radio-wl1273: fix a parameter name at kernel-doc macro
media: s3c-camif: add missing description at s3c_camif_find_format()
media: mtk-vpu: add description for wdt fields at struct mtk_vpu
media: vdec: fix some kernel-doc warnings
...
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This pull is a bit larger than I'd like but a large bunch of it is
license fixes, AMD wanted to fix the licenses for a bunch of files
that were missing them,
Otherwise a bunch of TTM regression fix since the hugepage support,
some i915 and gvt fixes, a core connector free in a safe context fix,
and one bridge fix"
* tag 'drm-fixes-for-v4.15-rc3' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
drm/exynos: remove unnecessary function declaration
drm/exynos: remove unnecessary descrptions
drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
drm/exynos: Fix dma-buf import
drm/ttm: swap consecutive allocated pooled pages v4
drm: safely free connectors from connector_iter
drm/i915/gvt: set max priority for gvt context
drm/i915/gvt: Don't mark vgpu context as inactive when preempted
drm/i915/gvt: Limit read hw reg to active vgpu
drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
drm/i915/gvt: Emulate PCI expansion ROM base address register
drm/ttm: swap consecutive allocated cached pages v3
drm/ttm: roundup the shrink request to prevent skip huge pool
drm/ttm: add page order support in ttm_pages_put
drm/ttm: add set_pages_wb for handling page order more than zero
drm/ttm: add page order in page pool
...
|
|
Pull md fixes from Shaohua Li:
"Some MD fixes.
The notable one is a raid5-cache deadlock bug with dm-raid, others are
not significant"
* tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid1/10: add missed blk plug
md: limit mdstat resync progress to max_sectors
md/r5cache: move mddev_lock() out of r5c_journal_mode_set()
md/raid5: correct degraded calculation in raid5_error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
"Another set of DT fixes:
- Fixes from overlay code rework. A trifecta of fixes to the locking,
an out of bounds access, and a memory leak in of_overlay_apply()
- Clean-up at25 eeprom binding document
- Remove leading '0x' in unit-addresses from binding docs"
* tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: overlay: Make node skipping in init_overlay_changeset() clearer
of: overlay: Fix out-of-bounds write in init_overlay_changeset()
of: overlay: Fix (un)locking in of_overlay_apply()
of: overlay: Fix memory leak in of_overlay_apply() error path
dt-bindings: eeprom: at25: Document device-specific compatible values
dt-bindings: eeprom: at25: Grammar s/are can/can/
dt-bindings: Remove leading 0x from bindings notation
of: overlay: Remove else after goto
of: Spelling s/changset/changeset/
of: unittest: Remove bogus overlay mutex release from overlay_data_add()
|
|
Pull virtio bugfixes from Michael Tsirkin:
"A couple of minor bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: fix return value check in receive_mergeable()
virtio_mmio: add cleanup for virtio_mmio_remove
virtio_mmio: add cleanup for virtio_mmio_probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Just two small fixes for the new pvcalls frontend driver"
* tag 'for-linus-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: Fix a check in pvcalls_front_remove()
xen/pvcalls: check for xenbus_read() errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-12-08
this is a pull request of 6 patches for net/master.
Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.
iwlwifi
* fix rate-scaling to not start lowest possible rate
* fix the TX queue hang detection for AP/GO modes
* fix the TX queue hang timeout in monitor interfaces
* fix packet injection
* remove a wrong error message when dumping PCI registers
* fix race condition with RF-kill
* tell mac80211 when the MIC has been stripped (9000 series)
* tell mac80211 when the IVC has been stripped (9000 series)
* add 2 new PCI IDs, one for 9000 and one for 22000
* fix a queue hang due during a P2P Remain-on-Channel operation
brcmfmac
* fix a race which sometimes caused a crash during sdio unbind
* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first and only parameter of sl_alloc() is unused, so remove it.
Fixes: 5342b77c4123 slip: ("Clean up create and destroy")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79fb4 ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use meminfo to identify TX and RX payload regions and skip them in
collection of EDC, MC, and HMA.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use meminfo to get base address and size of MC memory. Also use same
meminfo for EDC memory dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect memory layout of various on-chip memory regions. Move code
for collecting on-chip memory information to cudbg_lib.c and update
cxgb4_debugfs.c to use the common function. Also include
cudbg_entity.h before cudbg_lib.h to avoid adding cudbg entity
structure forward declarations in cudbg_lib.h.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.
This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.
[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>] lr : [<80bff064>] psr: 200e0113
[12846.816648] sp : b90d9ae8 ip : b90d9ae8 fp : b90d9b44
[12846.821871] r10: 00000008 r9 : 0013250e r8 : 00000100
[12846.827094] r7 : 0000012c r6 : 00000000 r5 : 00000001 r4 : bac84900
[12846.833619] r3 : 00000000 r2 : b90d9b08 r1 : 00000000 r0 : bac84900
Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).
Fixes: c22a3f48ef99 ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ALR table operations are a sequence of related register operations which
should be protected from concurrent access. The alr_cache should also be
protected. Add alr_mutex doing that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After applying 2270bc5da3497945 ("bnxt_en: Fix netpoll handling") and
903649e718f80da2 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099ea ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 39e6c8208d7b ("net: solve a NAPI race") napi has been able
to be rescheduled within napi_complete_done() even in non-busypoll case,
but virtnet_poll() always enabled interrupts before complete, and when
napi was rescheduled within napi_complete_done() it did not disable
interrupts.
This caused more interrupts when event idx is disabled.
According to commit cbdadbbf0c79 ("virtio_net: fix race in RX VQ
processing") we cannot place virtqueue_enable_cb_prepare() after
NAPI_STATE_SCHED is cleared, so disable interrupts again if
napi_complete_done() returned false.
Tested with vhost-user of OVS 2.7 on host, which does not have the event
idx feature.
* Before patch:
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 1472 60.00 32763206 0 6430.32
212992 60.00 23384299 4589.56
Interrupts on guest: 9872369
Packets/interrupt: 2.37
* After patch
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 1472 60.00 32794646 0 6436.49
212992 60.00 32793501 6436.27
Interrupts on guest: 4941299
Packets/interrupt: 6.64
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- three more patches in regard to the SPDX license tags. The missing
tags for the files in arch/s390/kvm will be merged via the KVM tree.
With that all s390 related files should have their SPDX tags.
- a patch to get rid of 'struct timespec' in the DASD driver.
- bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix compat system call table
s390/mm: fix off-by-one bug in 5-level page table handling
s390: Remove redudant license text
s390: add a few more SPDX identifiers
s390/dasd: prevent prefix I/O error
s390: always save and restore all registers on context switch
s390/dasd: remove 'struct timespec' usage
s390/qdio: restrict target-full handling to IQDIO
s390/qdio: consider ERROR buffers for inbound-full condition
s390/virtio: add BSD license to virtio-ccw
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This fixes an out of bounds warning from KASAN in the ACPI CPPC
driver"
* tag 'acpi-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / CPPC: Fix KASAN global out of bounds warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes an issue in the device runtime PM framework that prevents
customer devices from resuming if runtime PM is disabled for one or
more of their supplier devices (as reflected by device links between
those devices)"
* tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Fix handling of suppliers with disabled runtime PM
|
|
Private destructor could be called when register_netdev() fail with
rtnl lock held. This will lead deadlock in tun_free_netdev() who tries
to hold rtnl_lock. Fixing this by switching to use spinlock to
synchronize.
Fixes: 96f84061620c ("tun: add eBPF based queue selection method")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make it more clear that nodes without "__overlay__" subnodes are
skipped, by reverting the logic and using continue.
This also reduces indentation level.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
If an overlay has no "__symbols__" node, but it has nodes without
"__overlay__" subnodes at the end (e.g. a "__fixups__" node), after
filling in all fragments for nodes with "__overlay__" subnodes,
"fragment = &fragments[cnt]" will point beyond the end of the allocated
array.
Hence writing to "fragment->overlay" will overwrite unallocated memory,
which may lead to a crash later.
Fix this by deferring both the assignment to "fragment" and the
offending write afterwards until we know for sure the node has an
"__overlay__" subnode, and thus a valid entry in "fragments[]".
Fixes: 61b4de4e0b384f4a ("of: overlay: minor restructuring")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
