summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2019-08-15drm/amd/display: Load NV12 SOC BB from firmwareLeo Li1-60/+96
[Why] Previous SOC bounding box firmware loading logic was for NV10, when we still had it in firmware. Now that it's brought into driver code, and NV12 BB is in firmware, this logic needs to be repurposed for NV12. [How] Set SOC_BOUNDING_BOX_VALID to false, and add the dcn_2_0_nv12_soc BB struct. In init_soc_bounding_box, load firmware to nv12 BB instead. In addition, conditionally update and patch the BB, depending on ASIC REV. Signed-off-by: Leo Li <sunpeng.li@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Enable MPO with pre-blend color processing (RGB)Michael Strauss4-2/+56
[Why] DCN10 performs color processing before MPC combination, causes color shift in RGB colorspaces when positive brightness offset is applied However, YCbCr is still unfixed and remains disabled [How] Add layerIndex to dc_plane_state and dc_plane_info structs Re-enable MPO when brightness is adjusted and colorspace is not YCbCr Set rear plane's brightness offset to 0 when front plane visible Signed-off-by: Michael Strauss <michael.strauss@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: audio cannot switch to internal when display turns offyanyan kang1-0/+8
[why] disable_az_endpoint has been skipped because dc->debug.az_endpoint_mute_only = true. [how] set dc->debug.az_endpoint_mute_only false when PPLIB’s PME notification function pointer is not NULL at the dcn10_resource construct function,because right now SMU/PPLIB and DAL all have the AZ D3 force PME notification implemented. AZ D3 should work. Signed-off-by: yanyan kang <Yanyan.Kang@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: check hpd before retry verify link capWenjing Liu3-21/+38
[why] During detection link training if a display is disconnected, the current code will retry 3 times of link training on disconnected link before giving up. [how] Before each retry check for HPD status, only retry verify link cap when HPD is still high. Also put a 10ms delay between each retry to improve the chance of success. Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: enable dcn_mem_pwr as golden setting updatesCharlene Liu1-2/+1
Enable dcn_mem_pwr as golden setting updates Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: 3.2.46Anthony Koo1-1/+1
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: fix dcn20 global sync dml param extractionDmytro Laktyushkin2-99/+131
Currently the paremeters are extracted as if dml is calculating using pipes as we pass them in. in reality, dml internally merges pipes into planes if pipe split is detected. This change adds reverse logic to dcn20_calculate_dlg_params so that the global sync parameters can be correctly extracted for all the pipes when pipe split is enabled. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: 3.2.45Anthony Koo1-1/+1
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add and refine DSC logs in enable sequenceNikola Cornij2-13/+35
[why] Some logs messages were not precise and some new log messages were needed after "get packed PPS" function was introduced Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add Logging for Gamma Related information (2/2)Wyatt Wood3-2/+40
[Why] A recent bug showed that logging would be useful in debugging various gamma issues. [How] Add logging in dc. Signed-off-by: Wyatt Wood <wyatt.wood@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Remove redundant definition of dwb_source enumsJulian Parkin1-12/+0
There are repeated (but guarded) definitions of dwb_src enums. There are also unused entires. Clean them up. Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add enum for H-timing divider modeQingqing Zhuo2-4/+10
Add h_timing_div_mode enum to better reflect possible register values. Replace previously programmed values with enum Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Register VUPDATE_NO_LOCK interrupts for DCN2Nicholas Kazlauskas1-10/+18
[Why] These are needed to send back DRM vblank events in the case where VRR is on. Without the interrupt enabled we're deferring the events into the vblank queue and userspace is left waiting forever to get back the events they need. Found using igt@kms_vrr - the test fails immediately due to vblank timeout. [How] Register them the same way we're handling it for DCN1. This fixes igt@kms_vrr for DCN2. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: David Francis <David.Francis@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: wake up ogam mem pwr before programming ocscCharlene Liu6-7/+49
[Description] OGAM_MEM_PWR could stay in light up when driver woke up to update gamma. either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away. Easy reproduce after LOW_MEM Power feature enables and resume from S3. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Julian Parkin <jparkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Correct DSC PPS logNikola Cornij1-1/+1
[why] A misleading message "Programming PPS" appears before both programming and "query PPS" functions [how] Move the message from "log PPS" function to "program PPS" function Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Check if set_blank_data_double_buffer exists before callVitaly Prosyak1-1/+2
Not all ASIC types have this function implemented - check before calling. Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com> Reviewed-by: Julian Parkin <jparkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Fix type of ODMCombineType fieldIlya Bakoulin1-1/+1
The type was changed previously to better reflect possible register values. Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add Logging for Gamma Related information (1/2)Wyatt Wood4-0/+16
[Why] A recent bug showed that logging would be useful in debugging various gamma issues. [How] Add new log types and logging code to the color module. Signed-off-by: Wyatt Wood <wyatt.wood@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Remove 4:2:2 DSC supportNikola Cornij1-2/+2
[why] If DSC is available, a higher picture quality is achieved by using DSC with 4:4:4 format. Using 4:2:2 instead does not offer any benefit and would only introduce loss of quality. Removing it reduces maintenance and testing effort. Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: reprogram VM config when system resumeLewis Huang1-0/+8
[Why] The vm config will be clear to 0 when system enter S4. It will cause hubbub didn't know how to fetch data when system resume. The flip always pending because earliest_inuse_address and request_address are different. [How] Reprogram VM config when system resume Signed-off-by: Lewis Huang <Lewis.Huang@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Enable type C hotplugEric Yang3-0/+61
[Why and How] We want to change where timing is done for alt mode. Some of the commented out #ifs are needed for DCN20 so we enable them for that case. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: HUBP/HUBBUB register programming fixesIlya Bakoulin5-5/+11
[Why] - Need to change interface function signature / add an enum to reflect the available register field values [How] - Add a new enum and modify existing functions to use it instead of bool Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: update optc odm interface for more than 2 oppsDmytro Laktyushkin6-26/+31
Current optc odm interface only accepts 2 opps, we need to expand this to allow 4 to 1 odm combine. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Update DML parametersIlya Bakoulin4-6/+46
[Why] Need to add DML struct members that were omitted in previous DML implemenations. [How] - Add missing enum values - Add missing struct members - Set new input values in the fetch functions Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Remove duplicate interface for programming FBJulian Parkin6-160/+50
[Why] There are currently two interfaces for exactly the same thing: hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub version is currently unused past dcn10, largely because the call from the dcn10 hardware sequencer does not call through the interface, so the hupb interface was used instead. This is confusing because of the duplicate code, the unused functions, and the fact that more that one block currently owns this set of registers. [How] Remove the hubp interface entirely, as well as the register declarations that are not longer needed because of this. Change the call site to always call the hubbub version through the interface. Fix the update_dchub function in dcn20_hubbub.c to program the correct registers for dcn20. Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: fix pipe selection logic in validateJun Lei1-2/+70
[why] Resource mapping done in dcn20_validate_bandwidth has a flaw: When a full update is performed, the HWSS will only update the MPCC tree for the stream that is updated as opposed to all streams. This means that when mapping pipes in validation, care must be taken to not change any existing mapping, otherwise it leads to partial hw programming [how] it's not strictly necessary to track which stream/mpcc tree is being updated, but rather it's sufficient to compare current and new state and just keep pipes that were previously already mapped unchanged. Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: 3.2.44Aric Cyr1-1/+1
Signed-off-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Set DSC before DIG front-end is connected to its back-endNikola Cornij7-84/+158
[why] At the time DIG FE is connected to its BE, the clocks in OTG are enabled and PHY will also be set up. When DSC has to be used to fit the stream into the available bandwidth, without DSC being set DIG could get exposed to the higer bandwidth it (or link) could handle. This causes the HW to "reject" video enable setup (the register shows that video enable was attempted, but the status bit shows it as disabled). [how] - Separate DSC setup into DSC register config and DSC PPS SDP setup - Move most of the DSC setup (register config) to before dcn10_link_encoder_connect_dig_be_to_fe() is called - Set up DSC PPS SDP after DIG FE is connected to its BE. This is because setting DSC PPS SDP before that has no effect. Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Change DSC policy from slices per column to minimum slice ↵Nikola Cornij1-39/+32
height [why] Minimum slice height is recommended by VESA DSC Spreadsheet user guide Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add HLG support in color moduleVitaly Prosyak1-41/+61
[Why & How] Support hlg OETF and EOTF based on BT.2100-2 Follow up is required. Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: clean up DML for DCN2xJun Lei2-17/+3
[why] Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since DMLv2 has gone through proper validation. v2 can now be used as the default and 1 level of fallback can be removed [how] remove previous workaround implemenation Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: enabling seamless boot sequence for dcn2Martin Leung17-36/+172
[Why] Seamless boot (building SW state inheriting BIOS-initialized timing) was enabled on DCN2, including fixes [How] Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/ Pixel clock. This is part 2 of 2 for seamless boot NV10 Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: fix dcn-specific clk_mgr init_clocksMartin Leung2-2/+6
[Why] underflow seen on certain monitor setups caused by making dcnxx_init_hw generic [How] by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr memset in an else statement so both memsets don't get set Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Make init_hw and init_pipes generic for seamless bootMartin Leung9-313/+312
[Why] For seamless boot the init_hw sequence must be split into actual hardware vs pipes, in order to defer pipe initialization to set mode and skip of pipe-destructive sequences [How] made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit deleted dcn20 specific versions. This is part 1 of a 2 partimplementation of seamless boot Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: 3.2.43Aric Cyr1-1/+1
Signed-off-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: wait for pending complete when enabling a planeJun Lei1-1/+19
[why] When planes are enabled, they must be enabled using VSYNC update (not immediate). However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address only. This operation would normally be okay, but if the locking for immediate flip happens to occur before the VUPDATE associated with the initial plane enablement, it will cause HW to hang. [how] HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane. Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: refactor gpio to allocate hw_container in constructorSu Sung Chung18-137/+245
[why] if dynamic allocation fails during gpio_open, it will cause crash due to page fault. [how] handle allocation when gpio object gets created and prevent from calling gpio_open if allocation failed Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add work-around option to skip DCN20 clock updatesJaehyun Chung2-0/+4
[Why] Auto Overclock Memory fails for some systems that don't support p-state. [How] Implement the workaround, and it's corresponding enable flag. Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: fixup DPP programming sequenceJun Lei9-47/+141
[why] DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not. This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need an increased divider will temporarily have actual DPP clock drop below minimum while DTO double buffering takes effect. This results in temporary underflow. [how] To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase. When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because we do not use dividers larger than 1. Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: make firmware info only load once during dc_bios createDmytro Laktyushkin12-79/+36
Currently every time DC wants to access firmware info we make a call into VBIOS. This makes no sense as there is nothing that can change runtime inside fw info and can cause issues when calling unstable bios during bringup. This change eliminate this behavior by only calling bios once for fw info and keeping it stored as part of dc_bios. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Synchronous DisplayPort Link TrainingDavid Galiffi7-125/+282
[WHY] We require a method to perform synchronous link training. [HOW] Sync LT is broken into 3 basic steps. "Begin" starts the state machine, and resets "preferred" link settings. "Attempt" will attempt to train the link with a given set of training parameters. "End" stops the state machine, and will optionally disable the link phy. Between "Begin" and "End" DPCD:600h must not be set to "2" (D3:Powered Down). Between "Begin" and "End", there may be multiple "Attempts" with different training parameters. Signed-off-by: David Galiffi <david.galiffi@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Improve sharing of HUBBUB register listsJulian Parkin1-3/+6
Add DCN20 common register list that contains registers shared between DCN20 generations. Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add 22, 24, and 26 degammaVitaly Prosyak2-46/+75
[Why & How] Support degamma ROM and RAM based on hardware capabilities. Some refactoring into color module Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com> Reviewed-by: Gary Kattan <Gary.Kattan@amd.com> Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Fix frames_to_insert mathBayan Zabihiyan1-10/+17
[Why] The math on deciding on how many "frames to insert" sometimes sent us over the max refresh rate. Also integer overflow can occur if we have high refresh rates. [How] Instead of clipping the frame duration such that it doesn’t go below the min, just remove a frame from the number of frames to insert. + Use unsigned long long for intermediate calculations to prevent integer overflow. Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: fix issue where 252-255 values are clippedAnthony Koo1-1/+2
[Why] When endpoint is at the boundary of a region, such as at 2^0=1 we find that the last segment has a sharp slope and some points are clipped at the top. [How] If end point is 1, which is exactly at the 2^0 region boundary, we need to program an additional region beyond this point. Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: reset hdmi tmds rate and data scramble on pipe resetWenjing Liu7-1/+49
[why] hdmi data scramble and tmds rate is not reset during pipe reset. [how] reset hdmi tmds rate and data scramble on pipe reset Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: reset drr programming on pipe resetWenjing Liu2-0/+7
[why] drr is still enabled after driver is unloaded causing black screen [how] disable drr during pipe reset. Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add DFS reference clock fieldYongqiang Sun1-0/+2
Add to clk_mgr_internal struct, for future use. Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/amd/display: Add PIXEL_RATE control regs for more instancesYongqiang Sun1-5/+20
For use by future ASICs Signed-off-by: Sung Lee <sung.lee@amd.com> Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-08-15drm/scheduler: use job count instead of peekChristian König1-2/+2
The spsc_queue_peek function is accessing queue->head which belongs to the consumer thread and shouldn't be accessed by the producer This is fixing a rare race condition when destroying entities. Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Monk.liu@amd.com Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-20 14:53:12 +0000