| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Misc updates from mlx5-next branch:
1) E-Switch vport metadata support for source vport matching
2) Convert mkey_table to XArray
3) Shared IRQs and to use single IRQ for all async EQs
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If CMDQ ring is full, hclge_cmd_send may return directly, but IMP still
working and HW pointer changed, SW ring pointer do not match the HW
pointer. This patch update the SW pointer every time when the space is
full, so it can work normally next time if IMP and HW still working.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HNS3_RXD_VLD_B bit has already been checked in hns3_add_frag
or hns3_handle_rx_bd before calling hns3_handle_bdinfo, so when
hns3_handle_bdinfo is called, the HNS3_RXD_VLD_B bit is always
set, which makes the checking in hns3_handle_bdinfo unnecessary.
This patch removes the RXD_VLD_B checking in hns3_handle_bdinfo.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes unused linkmode definition.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The frame column is based on rx_crc_errors and rx_frame_errors. So
l3l4 checksum error should not be counted by rx_crc_errors. Instead,
l3l4 checksum error should be counted in ifconfig error column.
Fixes: d3ec4ef66937 ("net: hns3: refactor the statistics updating for netdev")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since some MSI-X interrupt's status may be cleared by hardware,
so when the driver receives the interrupt, reading
HCLGE_VECTOR0_PF_OTHER_INT_STS_REG register will get an empty
unknown interrupt. For this case, the irq handler should enable
vector0 interrupt. This patch also use dev_info() instead of
dev_dbg() in the hclge_check_event_cause(), since this information
will be useful for normal usage.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VF reset may fail for some probabilistic reasons,
such as wait for hardware reset timeout, wait for mailbox
response timeout, so this patch tries to re-schedule the
reset task when the number of reset failing is under
HCLGEVF_RESET_MAX_FAIL_CNT. This patch also add a function
hclgevf_reset_err_handle() to handle the reset failing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Local device and link partner config auto-negotiation on both,
local device config pause frame use as: rx on/tx off,
link partner config pause frame use as: rx off/tx on.
We except the result is:
Local device:
Autonegotiate: on
RX: on
TX: off
RX negotiated: on
TX negotiated: off
Link partner:
Autonegotiate: on
RX: off
TX: on
RX negotiated: off
TX negotiated: on
But actually, the result of Local device and link partner is both:
Autonegotiate: on
RX: off
TX: off
RX negotiated: off
TX negotiated: off
The root cause is that the supported flag is has only Pause,
reference to the function genphy_config_advert():
static int genphy_config_advert(struct phy_device *phydev)
{
...
linkmode_and(phydev->advertising, phydev->advertising,
phydev->supported);
...
}
The pause frame use of link partner is rx off/tx on, so its
advertising only set the bit Asym_Pause, and the supported is
only set the bit Pause, so the result of linkmode_and(), is
rx off/tx off.
This patch adds Asym_Pause to the supported flag to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting -Wformat=2, there is a compiler warning like this:
hclge_main.c:xxx:x: warning: format not a string literal and no
format arguments [-Wformat-nonliteral]
strs[i].desc);
^~~~
This patch adds missing format parameter "%s" to snprintf() to
fix it.
Fixes: 46a3df9f9718 ("Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the
hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg
with vport->vport_id as pri_id, which is used as index for
hdev->tm_info.tc_info, it will cause out of bound access issue
if vport_id is equal to or larger than HNAE3_MAX_TC.
Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE.
So this patch adds two checks for above cases.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when there is share buffer in the SSU(storage
switching unit), the low waterline for RX private buffer is
too low to keep the hardware running. Hardware may have
processed all the packet stored in the private buffer of the
low waterline before the new packet comes, because hardware
only tell the peer send packet again when the private buffer
is under the low waterline.
So this patch only allocate RX private buffer if there is
enough buffer according to hardware user manual.
This patch also reserve some buffer for reusing when TC num
is less than or equal to 2, and change PAUSE_TRANS_GAP &
HCLGE_NON_DCB_ADDITIONAL_BUF according to hardware user
manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when TC num is one, the DCB will be disabled no matter if
pfc_en is non-zero or not.
This patch enables the DCB if pfc_en is non-zero, even when TC num
is one.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When change MTU or other operations, which just calling .reset_notify
to do HNAE3_DOWN_CLIENT and HNAE3_UP_CLIENT, then
the netdev_tx_reset_queue() in the hns3_clear_all_ring() will be
ignored. So the dev_watchdog() may misdiagnose a TX timeout.
This patch separates netdev_tx_reset_queue() from
hns3_clear_all_ring(), and unifies hns3_clear_all_ring() and
hns3_force_clear_all_ring into one, since they are doing
similar things.
Fixes: 3a30964a2eef ("net: hns3: delay ring buffer clearing during reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need a better way to signal this, perhaps in phylink_validate, but
for now just print this error message as guidance for other people
looking at this driver's code while trying to rework PHYLINK.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYLINK being designed with PHYs in mind that can change MII protocol,
for correct operation it is necessary to ensure that the PHY interface
mode stays the same (otherwise clear the supported bit mask, as
required).
Because this is just a hypothetical situation for now, we don't bother
to check whether we could actually support the new PHY interface mode.
Actually we could modify the xMII table, reset the switch and send an
updated static configuration, but adding that would just be dead code.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been pointed out that PHYLINK can call mac_config only to update
the phy_interface_type and without knowing what the AN results are.
Experimentally, when this was observed to happen, state->link was also
unset, and therefore was used as a proxy to ignore this call. However it
is also suggested that state->link is undefined for this callback and
should not be relied upon.
So let the previously-dead codepath for SPEED_UNKNOWN be called, and
update the comment to make sure the MAC's behavior is sane.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit architectures, putting an array of 256 u32 values on the
stack uses more space than the warning limit:
drivers/net/ethernet/huawei/hinic/hinic_main.c: In function 'hinic_rss_init':
drivers/net/ethernet/huawei/hinic/hinic_main.c:286:1: error: the frame size of 1068 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
I considered changing the code to use u8 values here, since that's
all the hardware supports, but dynamically allocating the array is
a more isolated fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We support more speeds now. Update the Kconfig entry.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only disable the interrupts if RX NAPI gets to be scheduled. Also,
schedule the TX NAPI only when the interrupts are disabled.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the RX Tail Pointer to the last available SKB entry.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, stmmac only supports 32 bits addressing for SKB. Enable the
support for upto 48 bits addressing in XGMAC core.
This avoids the use of bounce buffers and increases performance.
Changes from v1:
- Fallback to 32 bits in failure (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a performance killer and anyways the interrupts are being
disabled by RX NAPI so no need to disable them again.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XGMAC supports following speeds:
- 10G XGMII
- 5G XGMII
- 2.5G XGMII
- 2.5G GMII
- 1G GMII
- 100M MII
- 10M MII
Add them to the stmmac driver.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Undefined burst shall only be set if pdata asks to.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For performance reasons decrease the default RX Watchdog value for the
minimum allowed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not enable EEE feature in the PHY if MAC does not support it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable the EDMA feature by default which gives higher performance.
Changes from v1:
- Do not use magic values (David)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some DT bindings do not have the PHY handle. Let's fallback to manually
discovery in case phylink_of_phy_connect() fails.
Changes from v1:
- Fixup comment style (Sergei)
Fixes: 74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic")
Reported-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Tested-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before "sis900: fix TX completion" patch, TX completion was done on TxIDLE interrupt.
TX completion also was the only thing done on TxIDLE interrupt.
Since "sis900: fix TX completion", TX completion is done on TxDESC interrupt.
So it is not necessary any more to set and to check for TxIDLE.
Eliminate TxIDLE from sis900.
Correct some typos, too.
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new GRE encapsulation support, which allows offload of filters
using tunnel_key set action in combination with actions that egress
to GRE type ports.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the existing tunnel matching support to include GRE decap
classification. Specifically matching existing tunnel fields for
NVGRE (GRE with protocol field set to TEB).
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously tunnel related functions in action offload only applied
to UDP tunnels. Rename these functions in preparation for new
tunnel types.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds IPv4 address and TTL/TOS helper functions, which is done in
preparation for compiling new tunnel types.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the key layer calculation function, in particular the tunnel
key layer calculation by introducing helper functions. This is done
in preparation for supporting GRE tunnel offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regmap provides read-modify-write function to update bitfields in
registers. Replace ad-hoc read-modify-write with regmap_update_bits()
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regmap provides polling function to poll for bits in a register. This
function is another reimplementation of polling for bit being clear in
a register. Replace this with regmap polling function. Moreover, inline
the function parameters, as the function is never called with any other
parameter values than this one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regmap provides polling function to poll for bits in a register. This
function is another reimplementation of polling for bit being clear in
a register. Replace this with regmap polling function. Moreover, inline
the function parameters, as the function is never called with any other
parameter values than this one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regmap provides polling function to poll for bits in a register. This
function is another reimplementation of polling for bit being clear in
a register. Replace this with regmap polling function. Moreover, inline
the function parameters, as the function is never called with any other
parameter values than this one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regmap provides polling function to poll for bits in a register,
use in instead of reimplementing it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes and one core framework fix
- Do a DT/firmware lookup in clk_core_get() even when the DT index is
a nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: socfpga: stratix10: fix divider entry for the emac clocks
clk: Do a DT parent lookup even when index < 0
clk: tegra210: Fix default rates for HDA clocks
clk: ti: clkctrl: Fix returning uninitialized data
clk: meson: meson8b: fix a typo in the VPU parent names array variable
clk: meson: fix MPLL 50M binding id typo
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix incorrect uses of kstrndup and DM logging macros in DM's early
init code.
- Fix DM log-writes target's handling of super block sectors so updates
are made in order through use of completion.
- Fix DM core's argument splitting code to avoid undefined behaviour
reported as a side-effect of UBSAN analysis on ppc64le.
- Fix DM verity target to limit the amount of error messages that can
result from a corrupt block being found.
* tag 'for-5.2/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity: use message limit for data block corruption message
dm table: don't copy from a NULL pointer in realloc_argv()
dm log writes: make sure super sector log updates are written in order
dm init: remove trailing newline from calls to DMERR() and DMINFO()
dm init: fix incorrect uses of kstrndup()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- fix for one corner case in HID++ protocol with respect to handling
very long reports, from Hans de Goede
- power management fix in Intel-ISH driver, from Hyungwoo Yang
- use-after-free fix in Intel-ISH driver, from Dan Carpenter
- a couple of new device IDs/quirks from Kai-Heng Feng, Kyle Godbey and
Oleksandr Natalenko
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: fix wrong driver_data usage
HID: multitouch: Add pointstick support for ALPS Touchpad
HID: logitech-dj: Fix forwarding of very long HID++ reports
HID: uclogic: Add support for Huion HS64 tablet
HID: chicony: add another quirk for PixArt mouse
HID: intel-ish-hid: Fix a use after free in load_fw_from_host()
|
|
Pull networking fixes from David Miller:
1) Fix ppp_mppe crypto soft dependencies, from Takashi Iawi.
2) Fix TX completion to be finite, from Sergej Benilov.
3) Use register_pernet_device to avoid a dst leak in tipc, from Xin
Long.
4) Double free of TX cleanup in Dirk van der Merwe.
5) Memory leak in packet_set_ring(), from Eric Dumazet.
6) Out of bounds read in qmi_wwan, from Bjørn Mork.
7) Fix iif used in mcast/bcast looped back packets, from Stephen
Suryaputra.
8) Fix neighbour resolution on raw ipv6 sockets, from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET
sctp: change to hold sk after auth shkey is created successfully
ipv6: fix neighbour resolution with raw socket
ipv6: constify rt6_nexthop()
net: dsa: microchip: Use gpiod_set_value_cansleep()
net: aquantia: fix vlans not working over bridged network
ipv4: reset rt_iif for recirculated mcast/bcast out pkts
team: Always enable vlan tx offload
net/smc: Fix error path in smc_init
net/smc: hold conns_lock before calling smc_lgr_register_conn()
bonding: Always enable vlan tx offload
net/ipv6: Fix misuse of proc_dointvec "skip_notify_on_dev_down"
ipv4: Use return value of inet_iif() for __raw_v4_lookup in the while loop
qmi_wwan: Fix out-of-bounds read
tipc: check msg->req data len in tipc_nl_compat_bearer_disable
net: macb: do not copy the mac address if NULL
net/packet: fix memory leak in packet_set_ring()
net/tls: fix page double free on TX cleanup
net/sched: cbs: Fix error path of cbs_module_init
tipc: change to use register_pernet_device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mamameed says:
====================
Generic DIM
From: Tal Gilboa and Yamin Fridman
Implement net DIM over a generic DIM library, add RDMA DIM
dim.h lib exposes an implementation of the DIM algorithm for
dynamically-tuned interrupt moderation for networking interfaces.
We want a similar functionality for other protocols, which might need to
optimize interrupts differently. Main motivation here is DIM for NVMf
storage protocol.
Current DIM implementation prioritizes reducing interrupt overhead over
latency. Also, in order to reduce DIM's own overhead, the algorithm might
take some time to identify it needs to change profiles. While this is
acceptable for networking, it might not work well on other scenarios.
Here we propose a new structure to DIM. The idea is to allow a slightly
modified functionality without the risk of breaking Net DIM behavior for
netdev. We verified there are no degradations in current DIM behavior with
the modified solution.
Suggested solution:
- Common logic is implemented in lib/dim/dim.c
- Net DIM (existing) logic is implemented in lib/dim/net_dim.c, which uses
the common logic in dim.c
- Any new DIM logic will be implemented in "lib/dim/new_dim.c".
This new implementation will expose modified versions of profiles,
dim_step() and dim_decision().
- DIM API is declared in include/linux/dim.h for all implementations.
Pros for this solution are:
- Zero impact on existing net_dim implementation and usage
- Relatively more code reuse (compared to two separate solutions)
- Increased extensibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QCA8337(N) has a RESETn signal on Pin B42 that
triggers a chip reset if the line is pulled low.
The datasheet says that: "The active low duration
must be greater than 10 ms".
This can hopefully fix some of the issues related
to pin strapping in OpenWrt for the EA8500 which
suffers from detection issues after a SoC reset.
Please note that the qca8k_probe() function does
currently require to read the chip's revision
register for identification purposes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first generation switches don't tell us through the dynamic config
interface whether the dumped FDB entries are static or not (the LOCKEDS
bit from P/Q/R/S).
However, now that we're keeping a mirror of all 'bridge fdb' commands in
the static config, this is an opportunity to compare a dumped FDB entry
to the driver's private database. After all, what makes an entry static
is that *we* added it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A FDB entry means that "frames that match this VID and DMAC must be
forwarded to this port".
In the case of dsa_8021q however, the VID is not a single one (and
neither two, as my previous patch assumed). The VID can be set either by
the CPU port (1 tx_vid), or by any of the other front-panel port (n-1
rx_vid's).
Fixes: 93647594d8f5 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.
To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
