| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The flushing of pending work in the EC driver uses drain_workqueue()
to flush the event handling work that can requeue itself via
advance_transaction(), but this is problematic, because that
work may also be requeued from the query workqueue.
Namely, if an EC transaction is carried out during the execution of
a query handler, it involves calling advance_transaction() which
may queue up the event handling work again. This causes the kernel
to complain about attempts to add a work item to the EC event
workqueue while it is being drained and worst-case it may cause a
valid event to be skipped.
To avoid this problem, introduce two new counters, events_in_progress
and queries_in_progress, incremented when a work item is queued on
the event workqueue or the query workqueue, respectively, and
decremented at the end of the corresponding work function, and make
acpi_ec_dispatch_gpe() the workqueues in a loop until the both of
these counters are zero (or system wakeup is pending) instead of
calling acpi_ec_flush_work().
At the same time, change __acpi_ec_flush_work() to call
flush_workqueue() instead of drain_workqueue() to flush the event
workqueue.
While at it, use the observation that the work item queued in
acpi_ec_query() cannot be pending at that time, because it is used
only once, to simplify the code in there.
Additionally, clean up a comment in acpi_ec_query() and adjust white
space in acpi_ec_event_processor().
Fixes: f0ac20c3f613 ("ACPI: EC: Fix flushing of pending work")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull vhost,virtio,vdpa bugfixes from Michael Tsirkin:
"Misc fixes all over the place.
Revert of virtio used length validation series: the approach taken
does not seem to work, breaking too many guests in the process. We'll
need to do length validation using some other approach"
[ This merge also ends up reverting commit f7a36b03a732 ("vsock/virtio:
suppress used length validation"), which came in through the
networking tree in the meantime, and was part of that whole used
length validation series - Linus ]
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa_sim: avoid putting an uninitialized iova_domain
vhost-vdpa: clean irqs before reseting vdpa device
virtio-blk: modify the value type of num in virtio_queue_rq()
vhost/vsock: cleanup removing `len` variable
vhost/vsock: fix incorrect used length reported to the guest
Revert "virtio_ring: validate used buffer length"
Revert "virtio-net: don't let virtio core to validate used length"
Revert "virtio-blk: don't let virtio core to validate used length"
Revert "virtio-scsi: don't let virtio core to validate used buffer length"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Intel VT-d fixes:
- Remove unused PASID_DISABLED
- Fix RCU locking
- Fix for the unmap_pages call-back
- Rockchip RK3568 address mask fix
- AMD IOMMUv2 log message clarification
* tag 'iommu-fixes-v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix unmap_pages support
iommu/vt-d: Fix an unbalanced rcu_read_lock/rcu_read_unlock()
iommu/rockchip: Fix PAGE_DESC_HI_MASKs for RK3568
iommu/amd: Clarify AMD IOMMUv2 initialization messages
iommu/vt-d: Remove unused PASID_DISABLED
|
|
Use the architecture independent Kconfig option PAGE_SIZE_LESS_THAN_64KB
to indicate that VMXNET3 requires a page size smaller than 64kB.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more block fixes from Jens Axboe:
"Turns out that the flushing out of pending fixes before the
Thanksgiving break didn't quite work out in terms of timing, so here's
a followup set of fixes:
- rq_qos_done() should be called regardless of whether or not we're
the final put of the request, it's not related to the freeing of
the state. This fixes an IO stall with wbt that a few users have
reported, a regression in this release.
- Only define zram_wb_devops if it's used, fixing a compilation
warning for some compilers"
* tag 'block-5.16-2021-11-27' of git://git.kernel.dk/linux-block:
zram: only make zram_wb_devops for CONFIG_ZRAM_WRITEBACK
block: call rq_qos_done() before ref check in batch completions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve fixes, eleven in drivers (target, qla2xx, scsi_debug, mpt3sas,
ufs). The core fix is a minor correction to the previous state update
fix for the iscsi daemons"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Zero clear zones at reset write pointer
scsi: core: sysfs: Fix setting device state to SDEV_RUNNING
scsi: scsi_debug: Sanity check block descriptor length in resp_mode_select()
scsi: target: configfs: Delete unnecessary checks for NULL
scsi: target: core: Use RCU helpers for INQUIRY t10_alua_tg_pt_gp
scsi: mpt3sas: Fix incorrect system timestamp
scsi: mpt3sas: Fix system going into read-only mode
scsi: mpt3sas: Fix kernel panic during drive powercycle test
scsi: ufs: ufs-mediatek: Add put_device() after of_find_device_by_node()
scsi: scsi_debug: Fix type in min_t to avoid stack OOB
scsi: qla2xxx: edif: Fix off by one bug in qla_edif_app_getfcinfo()
scsi: ufs: ufshpb: Fix warning in ufshpb_set_hpb_read_to_upiu()
|
|
When supporting only the .map and .unmap callbacks of iommu_ops,
the IOMMU driver can make assumptions about the size and alignment
used for mappings based on the driver provided pgsize_bitmap. VT-d
previously used essentially PAGE_MASK for this bitmap as any power
of two mapping was acceptably filled by native page sizes.
However, with the .map_pages and .unmap_pages interface we're now
getting page-size and count arguments. If we simply combine these
as (page-size * count) and make use of the previous map/unmap
functions internally, any size and alignment assumptions are very
different.
As an example, a given vfio device assignment VM will often create
a 4MB mapping at IOVA pfn [0x3fe00 - 0x401ff]. On a system that
does not support IOMMU super pages, the unmap_pages interface will
ask to unmap 1024 4KB pages at the base IOVA. dma_pte_clear_level()
will recurse down to level 2 of the page table where the first half
of the pfn range exactly matches the entire pte level. We clear the
pte, increment the pfn by the level size, but (oops) the next pte is
on a new page, so we exit the loop an pop back up a level. When we
then update the pfn based on that higher level, we seem to assume
that the previous pfn value was at the start of the level. In this
case the level size is 256K pfns, which we add to the base pfn and
get a results of 0x7fe00, which is clearly greater than 0x401ff,
so we're done. Meanwhile we never cleared the ptes for the remainder
of the range. When the VM remaps this range, we're overwriting valid
ptes and the VT-d driver complains loudly, as reported by the user
report linked below.
The fix for this seems relatively simple, if each iteration of the
loop in dma_pte_clear_level() is assumed to clear to the end of the
level pte page, then our next pfn should be calculated from level_pfn
rather than our working pfn.
Fixes: 3f34f1259776 ("iommu/vt-d: Implement map/unmap_pages() iommu_ops callback")
Reported-by: Ajay Garg <ajaygargnsit@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Link: https://lore.kernel.org/all/20211002124012.18186-1-ajaygargnsit@gmail.com/
Link: https://lore.kernel.org/r/163659074748.1617923.12716161410774184024.stgit@omen
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211126135556.397932-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
If we return -EOPNOTSUPP, the rcu lock remains lock. This is spurious.
Go through the end of the function instead. This way, the missing
'rcu_read_unlock()' is called.
Fixes: 7afd7f6aa21a ("iommu/vt-d: Check FL and SL capability sanity in scalable mode")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/40cc077ca5f543614eab2a10e84d29dd190273f6.1636217517.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211126135556.397932-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
With the submission of iommu driver for RK3568 a subtle bug was
introduced: PAGE_DESC_HI_MASK1 and PAGE_DESC_HI_MASK2 have to be
the other way arround - that leads to random errors, especially when
addresses beyond 32 bit are used.
Fix it.
Fixes: c55356c534aa ("iommu: rockchip: Add support for iommu v2")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dan Johansen <strit@manjaro.org>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Link: https://lore.kernel.org/r/20211124021325.858139-1-knaerzche@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The messages printed on the initialization of the AMD IOMMUv2 driver
have caused some confusion in the past. Clarify the messages to lower
the confusion in the future.
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20211123105507.7654-3-joro@8bytes.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter.
Current release - regressions:
- r8169: fix incorrect mac address assignment
- vlan: fix underflow for the real_dev refcnt when vlan creation
fails
- smc: avoid warning of possible recursive locking
Current release - new code bugs:
- vsock/virtio: suppress used length validation
- neigh: fix crash in v6 module initialization error path
Previous releases - regressions:
- af_unix: fix change in behavior in read after shutdown
- igb: fix netpoll exit with traffic, avoid warning
- tls: fix splice_read() when starting mid-record
- lan743x: fix deadlock in lan743x_phy_link_status_change()
- marvell: prestera: fix bridge port operation
Previous releases - always broken:
- tcp_cubic: fix spurious Hystart ACK train detections for
not-cwnd-limited flows
- nexthop: fix refcount issues when replacing IPv6 groups
- nexthop: fix null pointer dereference when IPv6 is not enabled
- phylink: force link down and retrigger resolve on interface change
- mptcp: fix delack timer length calculation and incorrect early
clearing
- ieee802154: handle iftypes as u32, prevent shift-out-of-bounds
- nfc: virtual_ncidev: change default device permissions
- netfilter: ctnetlink: fix error codes and flags used for kernel
side filtering of dumps
- netfilter: flowtable: fix IPv6 tunnel addr match
- ncsi: align payload to 32-bit to fix dropped packets
- iavf: fix deadlock and loss of config during VF interface reset
- ice: avoid bpf_prog refcount underflow
- ocelot: fix broken PTP over IP and PTP API violations
Misc:
- marvell: mvpp2: increase MTU limit when XDP enabled"
* tag 'net-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
net: dsa: microchip: implement multi-bridge support
net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
net: mscc: ocelot: set up traps for PTP packets
net: ptp: add a definition for the UDP port for IEEE 1588 general messages
net: mscc: ocelot: create a function that replaces an existing VCAP filter
net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
net: hns3: fix incorrect components info of ethtool --reset command
net: hns3: fix one incorrect value of page pool info when queried by debugfs
net: hns3: add check NULL address for page pool
net: hns3: fix VF RSS failed problem after PF enable multi-TCs
net: qed: fix the array may be out of bound
net/smc: Don't call clcsock shutdown twice when smc shutdown
net: vlan: fix underflow for the real_dev refcnt
ptp: fix filter names in the documentation
ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
nfc: virtual_ncidev: change default device permissions
net/sched: sch_ets: don't peek at classes beyond 'nbands'
net: stmmac: Disable Tx queues when reconfiguring the interface
selftests: tls: test for correct proto_ops
tls: fix replacing proto_ops
...
|
|
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e25 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a NULL pointer dereference in the CPPC library code and a
locking issue related to printing the names of ACPI device nodes in
the device properties framework.
Specifics:
- Fix NULL pointer dereference in the CPPC library code occuring on
hybrid systems without CPPC support (Rafael Wysocki).
- Avoid attempts to acquire a semaphore with interrupts off when
printing the names of ACPI device nodes and clean up code on top of
that fix (Sakari Ailus)"
* tag 'acpi-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Add NULL pointer check to cppc_get_perf()
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address three issues in the intel_pstate driver and fix two
problems related to hibernation.
Specifics:
- Make intel_pstate work correctly on Ice Lake server systems with
out-of-band performance control enabled (Adamos Ttofari).
- Fix EPP handling in intel_pstate during CPU offline and online in
the active mode (Rafael Wysocki).
- Make intel_pstate support ITMT on asymmetric systems with
overclocking enabled (Srinivas Pandruvada).
- Fix hibernation image saving when using the user space interface
based on the snapshot special device file (Evan Green).
- Make the hibernation code release the snapshot block device using
the same mode that was used when acquiring it (Thomas Zeitlhofer)"
* tag 'pm-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: Fix snapshot partial write lengths
PM: hibernate: use correct mode for swsusp_close()
cpufreq: intel_pstate: ITMT support for overclocked system
cpufreq: intel_pstate: Fix active mode offline/online EPP handling
cpufreq: intel_pstate: Add Ice Lake server to out-of-band IDs
|
|
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73
https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050
https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes: ddccc5e368a3 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes: 850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes: 850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.
Before the change:
crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci
After the change:
crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.
* acpi-properties:
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
|
|
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---
Fixes: 5fabb01207a2d ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4961 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a6be ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"Here is a single binder driver fix for 5.16-rc3.
It resolves a problem reported in the set of binder fixes that went
into 5.16-rc1. It has been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix test regression due to sender_euid change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes and one driver removal for
5.16-rc3.
The fixes resolve a number of small issues found in 5.16-rc1, nothing
huge at all. The driver removal was due to a platform being removed in
5.16-rc1, but this driver was forgotten about. It wasn't being built
anymore so it's safe to delete.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()
staging: greybus: Add missing rwsem around snd_ctl_remove() calls
staging: Remove Netlogic XLP network driver
staging: r8188eu: fix a memory leak in rtw_wx_read32()
staging: r8188eu: use GFP_ATOMIC under spinlock
staging: r8188eu: Use kzalloc() with GFP_ATOMIC in atomic context
staging/fbtft: Fix backlight
staging: r8188eu: Fix breakage introduced when 5G code was removed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for reported problems for
5.16-rc3
They include:
- typec driver fixes
- new usb-serial driver ids
- usb hub enumeration issues that were much reported
- gadget driver fixes
- dwc3 driver fix
- chipidea driver fixe
All of these have been in linux-next with no reported problems"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Fibocom FM101-GL variants
usb: typec: tipd: Fix initialization sequence for cd321x
usb: typec: tipd: Fix typo in cd321x_switch_power_state
usb: hub: Fix locking issues with address0_mutex
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
usb: chipidea: ci_hdrc_imx: fix potential error pointer dereference in probe
usb: hub: Fix usb enumeration issue due to address0 race
usb: typec: fusb302: Fix masking of comparator and bc_lvl interrupts
usb: dwc3: leave default DMA for PCI devices
usb: dwc2: hcd_queue: Fix use of floating point literal
usb: dwc3: gadget: Fix null pointer exception
usb: gadget: udc-xilinx: Fix an error handling path in 'xudc_probe()'
usb: xhci: tegra: Check padctrl interrupt presence in device tree
usb: dwc2: gadget: Fix ISOC flow for elapsed frames
usb: dwc3: gadget: Check for L1/L2/U3 for Start Transfer
usb: dwc3: gadget: Ignore NoStream after End Transfer
usb: dwc3: core: Revise GHWPARAMS9 offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- mmc_spi: Add SPI IDs to silence warning
- sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
- sdhci-esdhc-imx: Disable broken CMDQ for imx8qm/imx8qxp/imx8mm
* tag 'mmc-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: spi: Add device-tree SPI IDs
mmc: sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
mmc: sdhci-esdhc-imx: disable CMDQ support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has an interrupt storm fix for the i801, better timeout handling
for the new virtio driver, and some documentation fixes this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
docs: i2c: smbus-protocol: mention the repeated start condition
i2c: virtio: disable timeout handling
i2c: i801: Fix interrupt storm from SMB_ALERT signal
i2c: i801: Restore INTREN on unload
dt-bindings: i2c: imx-lpi2c: Fix i.MX 8QM compatible matching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- Kconfig fix to make it possible to control building of the privcmd
driver
- three fixes for issues identified by the kernel test robot
- a five-patch series to simplify timeout handling for Xen PV driver
initialization
- two patches to fix error paths in xenstore/xenbus driver
initialization
* tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: make HYPERVISOR_set_debugreg() always_inline
xen: make HYPERVISOR_get_debugreg() always_inline
xen: detect uninitialized xenbus in xenbus_init
xen: flag xen_snd_front to be not essential for system boot
xen: flag pvcalls-front to be not essential for system boot
xen: flag hvc_xen to be not essential for system boot
xen: flag xen_drm_front to be not essential for system boot
xen: add "not_essential" flag to struct xenbus_driver
xen/pvh: add missing prototype to header
xen: don't continue xenstore initialization in case of errors
xen/privcmd: make option visible in Kconfig
|
|
If writeback isn't configured, then we get the following warning when
compiling zram:
drivers/block/zram/zram_drv.c:1824:45: warning: unused variable 'zram_wb_devops' [-Wunused-const-variable]
Make sure we only define the block_device_operations if that option is
enabled.
Link: https://lore.kernel.org/lkml/202111261614.gCJMqcyh-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull drm fixes from Dave Airlie:
"No idea if turkey comes before pull request processing, but here's the
regular week's fixes. A bunch for amdgpu, nouveau adds support for a
new GPU (like a PCI ID addition), and a scattering of fixes across
i915/hyperv/aspeed/vc4.
Specifics:
amdgpu:
- SRIOV fixes
- dma-buf double free fix
- Display fixes for GPU resets
- Fix DSC powergating regression
- GPU TSC fixes
- Interrupt handler overflow fixes
- Endian fix in IP discovery table handling
- Aldebaran ASPM fix
- Fix overclocking regression on older asics
- Backlight/ACPI fix
amdkfd:
- SVM fixes
- VMA removal race fix
hyperv:
- removal fix
aspeed:
- vga_pw sysfs file fix
vc4:
- error checking fix
nouveau:
- support GA106
- fix a few error checks
i915:
- fix wakeref handling around PXP suspend"
* tag 'drm-fixes-2021-11-26' of git://anongit.freedesktop.org/drm/drm: (25 commits)
drm/amd/display: update bios scratch when setting backlight
drm/amdgpu/pm: fix powerplay OD interface
drm/amdgpu: Skip ASPM programming on aldebaran
drm/amdgpu: fix byteorder error in amdgpu discovery
drm/amdgpu: enable Navi retry fault wptr overflow
drm/amdgpu: enable Navi 48-bit IH timestamp counter
drm/amdkfd: simplify drain retry fault
drm/amdkfd: handle VMA remove race
drm/amdkfd: process exit and retry fault race
drm/amdgpu: IH process reset count when restart
drm/amdgpu/gfx9: switch to golden tsc registers for renoir+
drm/amdgpu/gfx10: add wraparound gpu counter check for APUs as well
drm/amdgpu: move kfd post_reset out of reset_sriov function
drm/amd/display: Fixed DSC would not PG after removing DSC stream
drm/amd/display: Reset link encoder assignments for GPU reset
drm/amd/display: Set plane update flags for all planes in reset
drm/amd/display: Fix DPIA outbox timeout after GPU reset
drm/amdgpu: Fix double free of dmabuf
drm/amdgpu: Fix MMIO HDP flush on SRIOV
drm/i915/gt: Hold RPM wakelock during PXP suspend
...
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fix wakeref handling of PXP suspend.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YZ65bsPOK+6JLv0d@intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One removal fix for hyperv, one fix in aspeed for the vga_pw sysfs file
content, one error-checking fix for vc4 and two fixes for nouveau, one
to support a new device and another one to properly check for errors.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211125101819.ynu7zgbs7yfwedri@houat
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- Add a NO APST quirk for a Kioxia device (Enzo Matsumiya)
- Fix write zeroes pi (Klaus Jensen)
- Various TCP transport fixes (Maurizio Lombardi and Varun
Prakash)
- Ignore invalid fast_io_fail_tmo values (Maurizio Lombardi)
- Use IOCB_NOWAIT only if the filesystem supports it (Maurizio
Lombardi)
- Module loading fix (Ming)
- Kerneldoc warning fix (Yang)
* tag 'block-5.16-2021-11-25' of git://git.kernel.dk/linux-block:
block: fix parameter not described warning
nvmet: use IOCB_NOWAIT only if the filesystem supports it
nvme: fix write zeroes pi
nvme-fabrics: ignore invalid fast_io_fail_tmo values
nvme-pci: add NO APST quirk for Kioxia device
nvme-tcp: fix memory leak when freeing a queue
nvme-tcp: validate R2T PDU in nvme_tcp_handle_r2t()
nvmet-tcp: fix incomplete data digest send
nvmet-tcp: fix memory leak when performing a controller reset
nvmet-tcp: add an helper to free the cmd buffers
nvmet-tcp: fix a race condition between release_queue and io_work
block: avoid to touch unloaded module instance when opening bdev
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are only a few devicetree fixes this time:
- one outdated devicetree property that slipped into the newly added
ExynosAutov9 support
- three changes to Broadcom SoCs that had incorrect number values for
interrupts or irqchips.
In the MAINTAINERS file, Nishanth Menon gets listed for TI K3 SoCs,
while Taichi Sugaya and Takao Orito take ownership of the Socionext
Milbeaut platform.
All other changes are for SoC specific drivers, fixing:
- A missing NULL pointer check in the mediatek memory driver
- An integer overflow issue in the Arm smccc firwmare interface
- A false-positive fortify-source check
- Error handling fixes for optee and smci
- Incorrect message format in one SCMI call"
* tag 'arm-fixes-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
memory: mtk-smi: Fix a null dereference for the ostd
arm64: dts: exynos: drop samsung,ufs-shareability-reg-offset in ExynosAutov9
MAINTAINERS: Update maintainer entry for keystone platforms
MAINTAINERS: Add entry to MAINTAINERS for Milbeaut
firmware: smccc: Fix check for ARCH_SOC_ID not implemented
ARM: socfpga: Fix crash with CONFIG_FORTIRY_SOURCE
firmware: arm_scmi: Fix type error assignment in voltage protocol
firmware: arm_scmi: Fix type error in sensor protocol
firmware: arm_scmi: pm: Propagate return value to caller
firmware: arm_scmi: Fix base agent discover response
optee: fix kfree NULL pointer
ARM: dts: bcm2711: Fix PCIe interrupts
ARM: dts: BCM5301X: Add interrupt properties to GPIO node
ARM: dts: BCM5301X: Fix I2C controller interrupt
firmware: arm_scmi: Fix null de-reference on error path
|
|
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes: f160e99462c6 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c235 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes: 50a909db36f2 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We add the ostd setting for mt8195. It introduces a KE for the
previous SoC which doesn't have ostd setting. This is the log:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000080
...
pc : mtk_smi_larb_config_port_gen2_general+0x64/0x130
lr : mtk_smi_larb_resume+0x54/0x98
...
Call trace:
mtk_smi_larb_config_port_gen2_general+0x64/0x130
pm_generic_runtime_resume+0x2c/0x48
__genpd_runtime_resume+0x30/0xa8
genpd_runtime_resume+0x94/0x2c8
__rpm_callback+0x44/0x150
rpm_callback+0x6c/0x78
rpm_resume+0x310/0x558
__pm_runtime_resume+0x3c/0x88
In the code: larbostd = larb->larb_gen->ostd[larb->larbid],
if "larb->larb_gen->ostd" is null, the "larbostd" is the offset(e.g.
0x80 above), it's also a valid value, then accessing "larbostd[i]" in the
"for" loop will cause the KE above. To avoid this issue, initialize
"larbostd" to NULL when the SoC doesn't have ostd setting.
Fixes: fe6dd2a4017d ("memory: mtk-smi: mt8195: Add initial setting for smi-larb")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211108082429.15080-1-yong.wu@mediatek.com
Link: https://lore.kernel.org/r/20211124085042.9649-3-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.16-rc3
Here's a fix for a pl2303 type-detection issue and some new modem
devices ids.
All but the last commit have been in linux-next, and with no reported
issues.
* tag 'usb-serial-5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variants
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
|
|
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3de5 ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The system will crash if we put an uninitialized iova_domain, this
could happen when an error occurs before initializing the iova_domain
in vdpasim_create().
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:__cpuhp_state_remove_instance+0x96/0x1c0
...
Call Trace:
<TASK>
put_iova_domain+0x29/0x220
vdpasim_free+0xd1/0x120 [vdpa_sim]
vdpa_release_dev+0x21/0x40 [vdpa]
device_release+0x33/0x90
kobject_release+0x63/0x160
vdpasim_create+0x127/0x2a0 [vdpa_sim]
vdpasim_net_dev_add+0x7d/0xfe [vdpa_sim_net]
vdpa_nl_cmd_dev_add_set_doit+0xe1/0x1a0 [vdpa]
genl_family_rcv_msg_doit+0x112/0x140
genl_rcv_msg+0xdf/0x1d0
...
So we must make sure the iova_domain is already initialized before
put it.
In addition, we may get the following warning in this case:
WARNING: ... drivers/iommu/iova.c:344 iova_cache_put+0x58/0x70
So we must make sure the iova_cache_put() is invoked only if the
iova_cache_get() is already invoked. Let's fix it together.
Cc: stable@vger.kernel.org
Fixes: 4080fc106750 ("vdpa_sim: use iova module to allocate IOVA addresses")
Signed-off-by: Longpeng <longpeng2@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211124015215.119-1-longpeng2@huawei.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Vdpa devices should be reset after unseting irqs of virtqueues, or we
will get errors when killing qemu process:
>> pi_update_irte: failed to update PI IRTE
>> irq bypass consumer (token 0000000065102a43) unregistration fails: -22
Signed-off-by: Wu Zongyong <wuzongyong@linux.alibaba.com>
Link: https://lore.kernel.org/r/a2cb60cf73be9da5c4e6399242117d8818f975ae.1636946171.git.wuzongyong@linux.alibaba.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
This was found by coccicheck:
./drivers/block/virtio_blk.c, 334, 14-17, WARNING Unsigned expression
compared with zero num < 0
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Link: https://lore.kernel.org/r/20211117063955.160777-1-ye.guojin@zte.com.cn
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: 02746e26c39e ("virtio-blk: avoid preallocating big SGL for data")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We can increment `total_len` directly and remove `len` since it
is no longer used for vhost_add_used().
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211122163525.294024-3-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
