| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:
drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.
Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.
Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for devlink reload action fw_activate with reload limit
no_reset which does firmware live patching, updating the firmware image
without reset, no downtime and no configuration lose. The driver checks
if the firmware is capable of handling the pending firmware changes as a
live patch. If it is then it triggers firmware live patching flow.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enable_remote_dev_reset devlink param flags that the host admin
allows resets by other hosts. In case it is cleared mlx5 host PF driver
will send NACK on pci sync for firmware update reset request and the
command will fail.
By default enable_remote_dev_reset parameter is true, so pci sync for
firmware update reset is enabled.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set capability to notify the firmware that this host driver is capable
of handling pci sync for firmware update events.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add functions to query and set the MFRL reset options supported by
firmware.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.
By default reload limit is unspecified and so no constraints on reload
actions are required.
Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.
The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.
Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
and devlink-resource values.
fw_activate: firmware activate.
command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
driver_reinit
$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Without these definitions, the driver will crash in:
mscc_ocelot_probe
-> ocelot_init
-> ocelot_vcap_init
-> __ocelot_target_read_ix
I missed this because I did not have the VSC7514 hardware to test, only
the VSC9959 and VSC9953, and the probing part is different.
Fixes: e3aea296d86f ("net: mscc: ocelot: add definitions for VCAP ES0 keys, actions and target")
Fixes: a61e365d7c18 ("net: mscc: ocelot: add definitions for VCAP IS1 keys, actions and target")
Reported-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull vhost fixes from Michael Tsirkin:
"Some last minute vhost,vdpa fixes.
The last two of them haven't been in next but they do seem kind of
obvious, very small and safe, fix bugs reported in the field, and they
are both in a new mlx5 vdpa driver, so it's not like we can introduce
regressions"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix dependency on MLX5_CORE
vdpa/mlx5: should keep avail_index despite device status
vhost-vdpa: fix page pinning leakage in error path
vhost-vdpa: fix vhost_vdpa_map() on error condition
vhost: Don't call log_access_ok() when using IOTLB
vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
vhost: Don't call access_ok() when using IOTLB
vhost vdpa: fix vhost_vdpa_open error handling
|
|
Pull networking fixes from Jakub Kicinski:
"One more set of fixes from the networking tree:
- add missing input validation in nl80211_del_key(), preventing
out-of-bounds access
- last minute fix / improvement of a MRP netlink (uAPI) interface
introduced in 5.9 (current) release
- fix "unresolved symbol" build error under CONFIG_NET w/o
CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
BTF.
- fix 32 bit sub-register bounds tracking in the bpf verifier for OR
case
- tcp: fix receive window update in tcp_add_backlog()
- openvswitch: handle DNAT tuple collision in conntrack-related code
- r8169: wait for potential PHY reset to finish after applying a FW
file, avoiding unexpected PHY behaviour and failures later on
- mscc: fix tail dropping watermarks for Ocelot switches
- avoid use-after-free in macsec code after a call to the GRO layer
- avoid use-after-free in sctp error paths
- add a device id for Cellient MPL200 WWAN card
- rxrpc fixes:
- fix the xdr encoding of the contents read from an rxrpc key
- fix a BUG() for a unsupported encoding type.
- fix missing _bh lock annotations.
- fix acceptance handling for an incoming call where the incoming
call is encrypted.
- the server token keyring isn't network namespaced - it belongs
to the server, so there's no need. Namespacing it means that
request_key() fails to find it.
- fix a leak of the server keyring"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
net: usb: qmi_wwan: add Cellient MPL200 card
macsec: avoid use-after-free in macsec_handle_frame()
r8169: consider that PHY reset may still be in progress after applying firmware
openvswitch: handle DNAT tuple collision
sctp: fix sctp_auth_init_hmacs() error path
bridge: Netlink interface fix.
net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
bpf: Fix scalar32_min_max_or bounds tracking
tcp: fix receive window update in tcp_add_backlog()
net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
mptcp: more DATA FIN fixes
net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
rxrpc: Fix server keyring leak
rxrpc: The server keyring isn't network-namespaced
rxrpc: Fix accept on a connection that need securing
rxrpc: Fix some missing _bh annotations on locking conn->state_lock
rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
rxrpc: Fix rxkad token xdr encoding
...
|
|
Remove propmt for selecting MLX5_VDPA by the user and modify
MLX5_VDPA_NET to select MLX5_VDPA. Also modify MLX5_VDPA_NET to depend
on mlx5_core.
This fixes an issue where configuration sets 'y' for MLX5_VDPA_NET while
MLX5_CORE is compiled as a module causing link errors.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 device")s
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201007064011.GA50074@mtl-vdi-166.wap.labs.mlnx
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
A VM with mlx5 vDPA has below warnings while being reset:
vhost VQ 0 ring restore failed: -1: Resource temporarily unavailable (11)
vhost VQ 1 ring restore failed: -1: Resource temporarily unavailable (11)
We should allow userspace emulating the virtio device be
able to get to vq's avail_index, regardless of vDPA device
status. Save the index that was last seen when virtq was
stopped, so that userspace doesn't complain.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601583511-15138-1-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>
|
|
Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.
Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca7e ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull drm nouveau fixes from Dave Airlie:
"Karol found two last minute nouveau fixes, they both fix crashes, the
TTM one follows what other drivers do already, and the other is for
bailing on load on unrecognised chipsets.
- fix crash in TTM alloc fail path
- return error earlier for unknown chipsets"
* tag 'drm-fixes-2020-10-08' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/mem: guard against NULL pointer access in mem_del
drm/nouveau/device: return error for unknown chipsets
|
|
other drivers seems to do something similar
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-2-kherbst@redhat.com
|
|
Previously the code relied on device->pri to be NULL and to fail probing
later. We really should just return an error inside nvkm_device_ctor for
unsupported GPUs.
Fixes: 24d5ff40a732 ("drm/nouveau/device: rework mmio mapping code to get rid of second map")
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Cc: dann frazier <dann.frazier@canonical.com>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006220528.13925-1-kherbst@redhat.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull another x86 platform driver fix from Hans de Goede:
"One final pdx86 fix for Tablet Mode reporting regressions (which make
the keyboard and touchpad unusable) on various Asus notebooks.
These regressions were caused by the asus-nb-wmi and the intel-vbtn
drivers both receiving recent patches to start reporting Tablet Mode /
to report it on more models.
Due to a miscommunication between Andy and me, Andy's earlier pull-req
only contained the fix for the intel-vbtn driver and not the fix for
the asus-nb-wmi code.
This fix has been tested as a downstream patch in Fedora kernels for
approx two weeks with no problems being reported"
* tag 'platform-drivers-x86-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Fix SW_TABLET_MODE always reporting 1 on many different models
|
|
Pull drm fixes from Dave Airlie:
"Daniel queued these up last week and I took a long weekend so didn't
get them out, but fixing the OOB access on get font seems like
something we should land and it's cc'ed stable as well.
The other big change is a partial revert for a regression on android
on the clcd fbdev driver, and one other docs fix.
fbdev:
- Re-add FB_ARMCLCD for android
- Fix global-out-of-bounds read in fbcon_get_font()
core:
- Small doc fix"
* tag 'drm-fixes-2020-10-06-1' of git://anongit.freedesktop.org/drm/drm:
drm: drm_dsc.h: fix a kernel-doc markup
Partially revert "video: fbdev: amba-clcd: Retire elder CLCD driver"
fbcon: Fix global-out-of-bounds read in fbcon_get_font()
Fonts: Support FONT_EXTRA_WORDS macros for built-in fonts
fbdev, newport_con: Move FONT_EXTRA_WORDS macros into linux/font.h
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use new helper for netstats settings
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mediadetect is another name for the EDPD (energy detect power down).
This feature allows device to save extra power when no link is available.
PHY goes into the extreme power saving mode and only periodically wakes up
and checks for the link.
AQC devices has fixed check period of 6 seconds
The feature may increase linkup time.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY downshift allows phy to try renegotiate if link is unstable
and can carry higher speed.
AQC devices has integrated PHY which is controlled by MAC firmware.
Thus, driver defines new ethtool callbacks to implement phy tunables
via netdev.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tail dropping is enabled for a port when:
1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.
AND
2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.
The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
different models
Commit b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for
SW_TABLET_MODE") added support for reporting SW_TABLET_MODE using the
Asus 0x00120063 WMI-device-id to see if various transformer models were
docked into their keyboard-dock (SW_TABLET_MODE=0) or if they were
being used as a tablet.
The new SW_TABLET_MODE support (naively?) assumed that non Transformer
devices would either not support the 0x00120063 WMI-device-id at all,
or would NOT set ASUS_WMI_DSTS_PRESENCE_BIT in their reply when querying
the device-id.
Unfortunately this is not true and we have received many bug reports about
this change causing the asus-wmi driver to always report SW_TABLET_MODE=1
on non Transformer devices. This causes libinput to think that these are
360 degree hinges style 2-in-1s folded into tablet-mode. Making libinput
suppress keyboard and touchpad events from the builtin keyboard and
touchpad. So effectively this causes the keyboard and touchpad to not work
on many non Transformer Asus models.
This commit fixes this by using the existing DMI based quirk mechanism in
asus-nb-wmi.c to allow using the 0x00120063 device-id for reporting
SW_TABLET_MODE on Transformer models and ignoring it on all other models.
Fixes: b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for SW_TABLET_MODE")
Link: https://patchwork.kernel.org/patch/11780901/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209011
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1876997
Reported-by: Samuel Čavoj <samuel@cavoj.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.9:
- Small doc fix.
- Re-add FB_ARMCLCD for android.
- Fix global-out-of-bounds read in fbcon_get_font().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8585daa2-fcbc-3924-ac4f-e7b5668808e0@linux.intel.com
|
|
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
"We have some fixes for Tablet Mode reporting in particular, that users
are complaining a lot about.
Summary:
- Attempt #3 of enabling Tablet Mode reporting w/o regressions
- Improve battery recognition code in ASUS WMI driver
- Fix Kconfig dependency warning for Fujitsu and LG laptop drivers
- Add fixes in Thinkpad ACPI driver for _BCL method and NVRAM polling
- Fix power supply extended topology in Mellanox driver
- Fix memory leak in OLPC EC driver
- Avoid static struct device in Intel PMC core driver
- Add support for the touchscreen found in MPMAN Converter9 2-in-1
- Update MAINTAINERS to reflect the real state of affairs"
* tag 'platform-drivers-x86-v5.9-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: re-initialize ACPI buffer size when reuse
MAINTAINERS: Add Mark Gross and Hans de Goede as x86 platform drivers maintainers
platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting
platform/x86: intel-vbtn: Revert "Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360"
platform/x86: intel_pmc_core: do not create a static struct device
platform/x86: mlx-platform: Fix extended topology configuration for power supply units
platform/x86: pcengines-apuv2: Fix typo on define of AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
platform/x86: fix kconfig dependency warning for FUJITSU_LAPTOP
platform/x86: fix kconfig dependency warning for LG_LAPTOP
platform/x86: thinkpad_acpi: initialize tp_nvram_state variable
platform/x86: intel-vbtn: Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360
platform/x86: asus-wmi: Add BATC battery name to the list of supported
platform/x86: asus-nb-wmi: Revert "Do not load on Asus T100TA and T200TA"
platform/x86: touchscreen_dmi: Add info for the MPMAN Converter9 2-in-1
Documentation: laptops: thinkpad-acpi: fix underline length build warning
Platform: OLPC: Fix memleak in olpc_ec_probe
|
|
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
|
|
Convert m88e1318_get_wol() to use the well implemented phy_read_paged()
instead of open coding it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
