| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We should no longer be calling the old pop routine for the vcc, after
vcc_release() has completed. Make sure we wait for any pending TX skbs
to complete, by waiting for our own PKT_PCLOSE control skb to be sent.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit 82167cb8c6b2f8166d5c7532e5ef4b5e0cc46a72 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.
It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:
1. Define a hidden HAVE_NET_DSA option and move the dependencies of
NET_DSA to that. While we're at it, drop the deprecated
EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
option.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid any possible message logging interleaving by adding
missing newlines.
Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:
net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]
Earlier approach to fix this was discussed here:
lkml.org/lkml/2012/10/29/549
This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recovery doesn't work too well if we leave interrupts disabled...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for byte queue limits on RTL8139C+
Tested on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-By: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes (for me) a regression introduced by commit b01af457 ("8139cp:
set ring address before enabling receiver"). That commit configured the
descriptor ring addresses earlier in the initialisation sequence, in
order to avoid the possibility of triggering stray DMA before the
correct address had been set up.
Unfortunately, it seems that the hardware will scribble garbage into the
TxRingAddr registers when we enable "plus mode" Tx in the CpCmd
register. Observed on a Traverse Geos router board.
To deal with this, while not reintroducing the problem which led to the
original commit, we augment cp_start_hw() to write to the CpCmd register
*first*, then set the descriptor ring addresses, and then finally to
enable Rx and Tx in the original 8139 Cmd register. The datasheet
actually indicates that we should enable Tx/Rx in the Cmd register
*before* configuring the descriptor addresses, but that would appear to
re-introduce the problem that the offending commit b01af457 was trying
to solve. And this variant appears to work fine on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b26623dab7eeb1e9f5898c7a49458789dd492f20.
This reverts the revert, in net-next we'll try another scheme
to fix this bug using patches from David Woodhouse.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 arch fixes from Peter Anvin:
"Here is a collection of fixes for 3.7-rc7. This is a superset of
tglx' earlier pull request."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix ordering of CFI directives and recent ASM_CLAC additions
x86, microcode, AMD: Add support for family 16h processors
x86-32: Export kernel_stack_pointer() for modules
x86-32: Fix invalid stack address while in softirq
x86, efi: Fix processor-specific memcpy() build error
x86: remove dummy long from EFI stub
x86, mm: Correct vmflag test for checking VM_HUGETLB
x86, amd: Disable way access filter on Piledriver CPUs
x86/mce: Do not change worker's running cpu in cmci_rediscover().
x86/ce4100: Fix PCI configuration register access for devices without interrupts
x86/ce4100: Fix reboot by forcing the reboot method to be KBD
x86/ce4100: Fix pm_poweroff
MAINTAINERS: Update email address for Robert Richter
x86, microcode_amd: Change email addresses, MAINTAINERS entry
MAINTAINERS: Change Boris' email address
EDAC: Change Boris' email address
x86, AMD: Change Boris' email address
|
|
Pull MTD fixes from David Woodhouse:
"The most important part of this is that it fixes a regression in
Samsung NAND chip detection, introduced by some rework which went into
3.7. The initial fix wasn't quite complete, so it's in two parts. In
fact the first part is committed twice (Artem committed his own copy
of the same patch) and I've merged Artem's tree into mine which
already had that fix.
I'd have recommitted that to make it somewhat cleaner, but figured by
this point in the release cycle it was better to merge *exactly* the
commits which have been in linux-next.
If I'd recommitted, I'd also omit the sparse warning fix. But it's
there, and it's harmless — just marking one function as 'static' in
onenand code.
This also includes a couple more fixes for stable: an AB-BA deadlock
in JFFS2, and an invalid range check in slram."
* tag 'for-linus-20121123' of git://git.infradead.org/mtd-2.6:
mtd: nand: fix Samsung SLC detection regression
mtd: nand: fix Samsung SLC NAND identification regression
jffs2: Fix lock acquisition order bug in jffs2_write_begin
mtd: onenand: Make flexonenand_set_boundary static
mtd: slram: invalid checking of absolute end address
mtd: ofpart: Fix incorrect NULL check in parse_ofoldpart_partitions()
mtd: nand: fix Samsung SLC NAND identification regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management update from Rafael Wysocki:
"Fix for an incorrect error condition check in device PM QoS code that
may lead to an Oops from Guennadi Liakhovetski."
* tag 'pm-for-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: fix wrong error-checking condition
|
|
Pull md fixes from NeilBrown:
"Several bug fixes for md in 3.7:
- raid5 discard has problems
- raid10 replacement devices have problems
- bad block lock seqlock usage has problems
- dm-raid doesn't free everything"
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
md/raid10: decrement correct pending counter when writing to replacement.
md/raid10: close race that lose writes lost when replacement completes.
md/raid5: Make sure we clear R5_Discard when discard is finished.
md/raid5: move resolving of reconstruct_state earlier in stripe_handle.
md/raid5: round discard alignment up to power of 2.
md: make sure everything is freed when dm-raid stops an array.
md: Avoid write invalid address if read_seqretry returned true.
md: Reassigned the parameters if read_seqretry returned true in func md_is_badblock.
|
|
Pull block layer fixes from Jens Axboe:
"Distilled down version of bug fixes for 3.7. The patches have been
well tested. If you notice that commit dates are from today, it's
because I pulled less important bits out and shuffled them into the
3.8 mix. Apart from that, no changes, base still the same.
It contains:
- Fix for aoe, don't run request_fn while it's plugged.
- Fix for a regression in floppy since 3.6, which causes problems if
no floppy is found.
- Stable fix for blk_exec(), don't touch a request after it has been
sent to the scheduler (and the device as well).
- Five fixes for various nasties in mtip32xx."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Don't access request after it might be freed
mtip32xx: Fix padding issue
aoe: avoid running request handler on plugged queue
mtip32xx: fix potential NULL pointer dereference in mtip_timeout_function()
mtip32xx: fix shift larger than type warning
mtip32xx: Fix incorrect mask used for erase mode
mtip32xx: Fix to make lba address correct in big-endian systems
mtip32xx: fix potential crash on SEC_ERASE_UNIT
dm: fix deadlock with request based dm and queue request_fn recursion
floppy: destroy floppy workqueue before cleaning up the queue
|
|
Pull omapdss fixes from Tomi Valkeinen:
"Here are a few OMAPDSS fixes for the next -rc. I'm sending these
directly to you, and quite late, as the fbdev tree maintainer
(Florian) has been busy with his work and hasn't had time to manage
the fb patches."
* tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: do not fail if dpll4_m4_ck is missing
OMAPFB: Fix possible null pointer dereferencing
OMAPDSS: HDMI: fix missing unlock on error in hdmi_dump_regs()
omapdss: dss: Fix clocks on OMAP363x
OMAPDSS: DSI: fix dsi_get_dsidev_from_id()
|
|
git://git.pengutronix.de/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
|
|
Pull networkign fixes from David Miller:
"Networking bug fixes, Cacio e Pepe edition:
1) BNX2X accidently accesses chip rev specific registers without an
appropriate guard, fix from Ariel Elior.
2) When we removed the routing cache, we set ip_rt_max_size to ~0 just
to keep reporting a value to userspace via sysfs. But the ipv4
IPSEC layer was using this to tune itself which is completely bogus
to now do. Fix from Steffen Klassert.
3) Missing initialization in netfilter ipset code from Jozsef
Kadlecsik.
4) Check CTA_TIMEOUT_NAME length properly in netfilter cttimeout code,
fix from Florian Westphal.
5) After removing the routing cache, we inadvertantly are caching
multicast routes that end up looping back locally, we cannot do
that legitimately any more. Fix from Julian Anastasov.
6) Revert a race fix for 8139cp qemu/kvm that doesn't actually work
properly on real hardware. From Francois Romieu.
7) Fixup errors in example command lines in VXLAN device docs."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
ipv4: do not cache looped multicasts
netfilter: cttimeout: fix buffer overflow
netfilter: ipset: Fix range bug in hash:ip,port,net
xfrm: Fix the gc threshold value for ipv4
|
|
dev_pm_qos_add_request() can return 0, 1, or a negative error code,
therefore the correct error test is "if (error < 0)." Checking just for
non-zero return code leads to erroneous setting of the req->dev pointer
to NULL, which then leads to a repeated call to
dev_pm_qos_add_ancestor_request() in st1232_ts_irq_handler(). This in turn
leads to an Oops, when the I2C host adapter is unloaded and reloaded again
because of the inconsistent state of its QoS request list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add information to the DMA Configuration Register to
maximize system performance:
- rx/tx packet buffer full memory size
- allow possibility to use INCR16 if supported
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joachim Eastwood <manabian@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On BE2 chip, an interrupt being raised even when EQ is in un-armed state has
been observed a few times. This is not expected and has never been
observed on BE3/Lancer chips.
As a consequence, be_msix()::events_get() and be_poll()::events_get()
can race and notify an EQ wrongly causing a CEV UE. The other possible
side-effect would be traffic stalling because after notifying EQ,
napi_schedule() is ignored as NAPI is already running.
This patch fixes this issue by counting events only in be_poll().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes tun_get_iff() prototype to return void as it never fails.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix bug where a register which was only meant to be read in 578xx/57712
devices causes a bogus error message to be logged when read from other
devices.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc95xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables LAN9500 family devices to wake from suspend
on either link up or link down events
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of storing the number of wake-up frame filter registers
in the pdata structure, this patch changes the driver to detect
the type of device we have and store its available features.
The new two features will be used in future patches.
This patch is intended to have no change in behaviour.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
without this patch the two lines below won't ever execute
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts b01af4579ec41f48e9b9c774e70bd6474ad210db.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hi Jens,
Another tiny patch.
Removed __packed before the struct smart_attr and added __packed at end of
the structure to fix padding issue.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Calling the request handler directly on a plugged queue defeats
the performance improvements provided by the plugging mechanism.
Use the __blk_run_queue function instead of calling the request
handler directly, so that we don't interfere with the block
layer's ability to plug the queue.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The dereference to port should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we're building a 32-bit kernel and CONFIG_LBADF isn't set,
sector_t is 32-bits wide. The shifts by 32 and 40 are thus
larger than we support.
Cast the sector offset to a u64 to avoid these warnings.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previous commit use value 3 for erasemode mask.
Changing the mask to correct value to 2
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Earlier lba address was assigned directly to lba_low and lba_low_ex,
which would result in a different number (bytes reversed) in
big-endian systems. Now assigning lba address byte-by-byte to fis.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The mtip driver lifted this code from elsewhere and then added a special
handling check for SEC_ERASE_UNIT. If the caller tries to do a security
erase but passes no output data for the command then outbuf is not
allocated and the driver duly explodes.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Request based dm attempts to re-run the request queue off the
request completion path. If used with a driver that potentially does
end_io from its request_fn, we could deadlock trying to recurse
back into request dispatch. Fix this by punting the request queue
run to kblockd.
Tested to fix a quickly reproducible deadlock in such a scenario.
Cc: stable@kernel.org
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We need to first destroy the floppy_wq workqueue before cleaning up
the queue. Otherwise we might race with still pending work with the
workqueue, but all the block queue already gone. This might lead to
various oopses, such as
CPU 0
Pid: 6, comm: kworker/u:0 Not tainted 3.7.0-rc4 #1 Bochs Bochs
RIP: 0010:[<ffffffff8134eef5>] [<ffffffff8134eef5>] blk_peek_request+0xd5/0x1c0
RSP: 0000:ffff88000dc7dd88 EFLAGS: 00010092
RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88000f602688 RSI: ffffffff81fd95d8 RDI: 6b6b6b6b6b6b6b6b
RBP: ffff88000dc7dd98 R08: ffffffff81fd95c8 R09: 0000000000000000
R10: ffffffff81fd9480 R11: 0000000000000001 R12: 6b6b6b6b6b6b6b6b
R13: ffff88000dc7dfd8 R14: ffff88000dc7dfd8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffffffff81e21000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 0000000001e11000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:0 (pid: 6, threadinfo ffff88000dc7c000, task ffff88000dc5ecc0)
Stack:
0000000000000000 0000000000000000 ffff88000dc7ddb8 ffffffff8134efee
ffff88000dc7ddb8 0000000000000000 ffff88000dc7dde8 ffffffff814aef3c
ffffffff81e75d80 ffff88000dc0c640 ffff88000fbfb000 ffffffff814aed90
Call Trace:
[<ffffffff8134efee>] blk_fetch_request+0xe/0x30
[<ffffffff814aef3c>] redo_fd_request+0x1ac/0x400
[<ffffffff814aed90>] ? start_motor+0x130/0x130
[<ffffffff8106b526>] process_one_work+0x136/0x450
[<ffffffff8106af65>] ? manage_workers+0x205/0x2e0
[<ffffffff8106bb6d>] worker_thread+0x14d/0x420
[<ffffffff8106ba20>] ? rescuer_thread+0x1a0/0x1a0
[<ffffffff8107075a>] kthread+0xba/0xc0
[<ffffffff810706a0>] ? __kthread_parkme+0x80/0x80
[<ffffffff818b553a>] ret_from_fork+0x7a/0xb0
[<ffffffff810706a0>] ? __kthread_parkme+0x80/0x80
Code: 0f 84 c0 00 00 00 83 f8 01 0f 85 e2 00 00 00 81 4b 40 00 00 80 00 48 89 df e8 58 f8 ff ff be fb ff ff ff
fe ff ff <49> 8b 1c 24 49 39 dc 0f 85 2e ff ff ff 41 0f b6 84 24 28 04 00
RIP [<ffffffff8134eef5>] blk_peek_request+0xd5/0x1c0
RSP <ffff88000dc7dd88>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
|
|
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four bug fixes.
The isci one is an obvious thinko (using request buffer instead of
response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because
they're part of a series of ten patches, the other seven of which went
into the block layer during the merge window meaning our current
DIF/DIX implementation is broken without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] sd: Implement support for WRITE SAME
[SCSI] sd: Permit merged discard requests
[SCSI] Add a report opcode helper
[SCSI] isci: copy fis 0x34 response into proper buffer
|
|
Pull drm fixes from Dave Airlie.
Small fixes for (mostly Nouveau, some radeon) regressions.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use the correct fence implementation for nv50
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
|
|
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled. Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Historically, we've been using the APME bit to determine whether a device
supports wake on a given port or not. However, this bit specifies the
default wake setting, rather than the wake support. Change the behavior so
that we use a flag to keep the capabilities separate from the enablement
while meeting customer requirements.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update the filters to be more consistent with what the driver wants to do.
For example, for devices that timestamp all packets, report that the filter
is set for timestamping all packets.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.
This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.
This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.
I am going to chalk this up as a bug and fix it now.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.
There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes the queuing that was previously done for L4 packets
as it is not needed. The filter does not provide functionality, and it
is possible that queue setup here could trample settings done else-where
in the driver. (for example it may use a queue which isn't setup.)
Setting of the queue is not required for hardware timestamping and could
have inadverdent side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
