| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On some systems (such as the Qualcomm APQ8060 Dragonboard) the
RESET signal of the SMSC911x is not pulled up by a resistor (or
the internal pull-up that will pull it up if the pin is not
even connected) but instead connected to a GPIO line, so that
the operating system must explicitly deassert RESET before use.
Support this in the SMSC911x driver so this ethernet connector
can be used on such targets.
Notice that we request the line to go logical low (deassert)
whilst the line on the actual component is active low. This
is managed in the respective hardware description when
specifying the GPIO line with e.g. device tree or ACPI. With
device tree it looks like this in one case:
reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
Which means that logically requesting the RESET line to be
deasserted will result in the line being driven high, taking
the device out of reset.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for dumping and formatting the HW/FW debug data.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_selftest.c:6:5: warning: no previous prototype for 'qed_selftest_memory' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:19:5: warning: no previous prototype for 'qed_selftest_interrupt' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:32:5: warning: no previous prototype for 'qed_selftest_register' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:55:5: warning: no previous prototype for 'qed_selftest_clock' [-Wmissing-prototypes]
In fact, these functions are declared in qed_selftest.h, so this patch
add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gpio_to_irq does not return NO_IRQ but instead returns a negative
error code on failure. Returning NO_IRQ from the function has no
negative effects as we only compare the result to the expected
interrupt number, but it's better to return a proper failure
code for consistency, and we should remove NO_IRQ from the kernel
entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Ma Yuying <yuma@redhat.com>
Suggested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/arc/emac_mdio.c:107:5: warning: no previous prototype for 'arc_mdio_reset' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for several infrastructure operations that are done as part of
debug data collection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.
$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
text data bss dec hex filename
127817 27969 32800 188586 2e0aa drivers/net/ethernet/qlogic/qed/built-in.o.new
132474 27969 32800 193243 2f2db drivers/net/ethernet/qlogic/qed/built-in.o.old
Miscellanea:
o Change allocs to the generally preferred forms where possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If vxlan_build_skb return err < 0, tx_errors should be also increased.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on the preempt mode, the bpf_prog stored in xdp_prog may be
freed despite the use of call_rcu inside bpf_prog_put. The situation is
possible when running in PREEMPT_RCU=y mode, for instance, since the rcu
callback for destroying the bpf prog can run even during the bh handling
in the mlx4 rx path.
Several options were considered before this patch was settled on:
Add a napi_synchronize loop in mlx4_xdp_set, which would occur after all
of the rings are updated with the new program.
This approach has the disadvantage that as the number of rings
increases, the speed of update will slow down significantly due to
napi_synchronize's msleep(1).
Add a new rcu_head in bpf_prog_aux, to be used by a new bpf_prog_put_bh.
The action of the bpf_prog_put_bh would be to then call bpf_prog_put
later. Those drivers that consume a bpf prog in a bh context (like mlx4)
would then use the bpf_prog_put_bh instead when the ring is up. This has
the problem of complexity, in maintaining proper refcnts and rcu lists,
and would likely be harder to review. In addition, this approach to
freeing must be exclusive with other frees of the bpf prog, for instance
a _bh prog must not be referenced from a prog array that is consumed by
a non-_bh prog.
The placement of rcu_read_lock in this patch is functionally the same as
putting an rcu_read_lock in napi_poll. Actually doing so could be a
potentially controversial change, but would bring the implementation in
line with sk_busy_loop (though of course the nature of those two paths
is substantially different), and would also avoid future copy/paste
problems with future supporters of XDP. Still, this patch does not take
that opinionated option.
Testing was done with kernels in either PREEMPT_RCU=y or
CONFIG_PREEMPT_VOLUNTARY=y+PREEMPT_RCU=n modes, with neither exhibiting
any drawback. With PREEMPT_RCU=n, the extra call to rcu_read_lock did
not show up in the perf report whatsoever, and with PREEMPT_RCU=y the
overhead of rcu_read_lock (according to perf) was the same before/after.
In the rx path, rcu_read_lock is eventually called for every packet
from netif_receive_skb_internal, so the napi poll call's rcu_read_lock
is easily amortized.
v2:
Remove extra rcu_read_lock in mlx4_en_process_rx_cq body
Annotate xdp_prog with __rcu, and convert all usages to rcu_assign or
rcu_dereference[_protected] as appropriate.
Add explicit mutex lock around rcu_assign instead of xchg loop.
Fixes: d576acf0a22 ("net/mlx4_en: add page recycle to prepare rx ring for tx support")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds support for aggregating more SKBs feed into NAPI in
order to get more benefits from generic receive offload (GRO) by
peeking at the RX ring status and moving more packets right before
returning from NAPI RX polling handler if NAPI budgets are still
available and some packets already present in hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
memory barrier used
The patch makes move wmb() to outside the loop that could help
RX path handling more faster although that RX descriptors aren't
freed for DMA to use as soon as possible, but based on my experiment
and the result shows it still can reach about 943Mbpis without
performance drop that is tested based on the setup with one port
using Giga PHY and 256 RX descriptors for DMA to move.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a more common logging style
Miscellanea:
o Add pr_fmt to prefix each output message
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Macros that end in an underscore are just odd.
Add hso_dbg(level, fmt, ...) and use it everwhere instead.
Several uses had additional unnecessary newlines as the
macro added a newline. Remove the newline from the macro
and add newlines to each use as appropriate.
Remove now unused D<digit> macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mdix control through ethtool.
Signed-off-by: Woojung Huh <Woojung.huh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add STRAP_STATUS defines.
Signed-off-by: Woojung Huh <Woojung.huh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since not every chip has a Global2 set of registers, make its support
optional, in which case the related functions will return -EOPNOTSUPP.
This also allows to reduce the size of the mv88e6xxx driver for devices
such as home routers embedding Ethernet chips without Global2 support.
It is present on most recent chips, thus enable its support by default.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell chips are composed of multiple SMI devices. One of them at
address 0x1C is called Global2. It provides an extended set of
registers, used for interrupt control, EEPROM access, indirect PHY
access (to bypass the PHY Polling Unit) and cross-chip related setup.
Most chips have it, but some others don't (older ones such as 6060).
Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Document each registers in the meantime.
Its compilation can be later avoided for chips without such registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the mv88e6xxx.c file has been renamed, the driver compiled as a
module is called chip.ko instead of mv88e6xxx.ko. Fix this.
Fixes: fad09c73c270 ("net: dsa: mv88e6xxx: rename single-chip support")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpmac_start_xmit() used the max() macro on skb->len (an unsigned int)
and ETH_ZLEN (a signed int literal). This led to the following compiler
warning:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/ti/cpmac.c:19:
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit':
include/linux/kernel.h:748:17: warning: comparison of distinct pointer
types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max'
len = max(skb->len, ETH_ZLEN);
^
On top of this, it assigned the result of the max() macro to a signed
integer whilst all further uses of it result in it being cast to varying
widths of unsigned integer.
Fix this up by using max_t to ensure the comparison is performed as
unsigned integers, and for consistency change the type of the len
variable to unsigned int.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for ndo_get_vf_config, also fill the default mac address
that will be provided to the VF by firmware, in case user doesn't
provide one. So user can get the default MAC address address also
through ndo_get_vf_config.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netns id should be already allocated each time we change
netns, that is, in dev_change_net_namespace() (more precisely
in rtnl_fill_ifinfo()). It is safe to just call peernet2id() here.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for pause frame and priv flag for cn23xx
device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds NAPI related support for cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for watchdog based health monitoring
of octeon cores on cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for some control operations like
LED identification, ethtool statistics and intr config for
cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for data path related changes based
on octeon3 instruction header(ih3) for cn23xx.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for Instruction Queue(IQ) index manipulation
routines through bar1 of cn23xx.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for RX control commands on cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds work queue support for link status and
control commands.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the gmac power domain support for rk3399, in order to save more
power consumption.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GMAC Power Domain(PD) will be disabled during suspend.
That will causes GRF registers reset.
So corresponding GRF registers for GMAC must be setup again.
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get a few warnings when building kernel with W=1:
drivers/isdn/hardware/mISDN/hfcmulti.c:568:1: warning: no previous declaration for 'enablepcibridge' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:574:1: warning: no previous declaration for 'disablepcibridge' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:580:1: warning: no previous declaration for 'readpcibridge' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:608:1: warning: no previous declaration for 'writepcibridge' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:638:1: warning: no previous declaration for 'cpld_set_reg' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:645:1: warning: no previous declaration for 'cpld_write_reg' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:657:1: warning: no previous declaration for 'cpld_read_reg' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:674:1: warning: no previous declaration for 'vpm_write_address' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:681:1: warning: no previous declaration for 'vpm_read_address' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:695:1: warning: no previous declaration for 'vpm_in' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:716:1: warning: no previous declaration for 'vpm_out' [-Wmissing-declarations]
drivers/isdn/hardware/mISDN/hfcmulti.c:1028:1: warning: no previous declaration for 'plxsd_checksync' [-Wmissing-declarations]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Qualcomm Technologies, Inc. EMAC gigabit Ethernet
controller.
This driver supports the following features:
1) Checksum offload.
2) Interrupt coalescing support.
3) SGMII phy.
4) phylib interface for external phy
Based on original work by
Niranjana Vishwanathapura <nvishwan@codeaurora.org>
Gilad Avidov <gavidov@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Access the priv member of the dsa_switch structure directly, instead of
having an unnecessary helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a5d ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The workqueue "pegasus_workqueue" queues a single work item per pegasus
instance and hence it doesn't require execution ordering. Hence,
alloc_workqueue has been used to replace the deprecated
create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure since it's a network driver.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set, replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "wq" queues multiple work items viz
&bond->mcast_work, &nnw->work, &bond->mii_work, &bond->arp_work,
&bond->alb_work, &bond->mii_work, &bond->ad_work, &bond->slave_arr_work
which require strict execution ordering. Hence, an ordered dedicated
workqueue has been used.
Since, it is a network driver, WQ_MEM_RECLAIM has been set to
ensure forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the sky2 driver to pass number of packets done to NAPI.
The driver was never updated when napi_complete_done was added.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support of Synopsys 3.50a MAC IP in stmmac driver.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stm324xx family chips support Synopsys MAC 3.510 IP.
This patch adds settings for logical glue logic:
-clocks
-mode selection MII or RMII.
Reviewed-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A bugfix for backward compatibility handling introduced undefined
behavior for the case that of_parse_phandle() does not return
a valid entry, as "gcc -Wmaybe-unused" reports:
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:776:6: error: 'phy_dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_mdio_config':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:776:6: error: 'phy_dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
We can work around this by removing the check for zero "np", as
of_phy_connect() will correctly handle a NULL argument so we fall
back into the normal error handling case.
Note that I had previously fixed another bug that resulted in the
exact same warning, but this is a different problem that was
introduced after my original fix.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 03377e381bf4 ("drivers: net: xgene: Fix backward compatibility")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check the coding style with checkpatch.pl and fix the warnings and errors.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Grant Grundler <grundler@chromium.org>
The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.
The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.
Ignore the ret value since it's ignored in XXX_link_reset() functions.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From: Grant Grundler <grundler@chromium.org>
https://lkml.org/lkml/2014/11/11/947
Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
