Age | Commit message (Collapse) | Author | Files | Lines |
|
Port Key was determined as 16 bits according to the link speed,
duplex and user key (which is yet not supported). In the old
speed field, 5 bits are for speed [1|10|100|1000|10000]Mbps as
below:
--------------------------------------------------------------
Port key :| User key | Speed | Duplex|
--------------------------------------------------------------
16 6 1 0
This patch keeps the old layout, but changes AD_LINK_SPEED_BITMASK
from bit type to an enum type. In this way, the speed field can
expand speed type from 5 to 32.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
remove unused variable
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When run ./scripts/kernel-doc several warnings are reported
so this patch fix them.
Also it reviews many comments and adds new ones.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds some useful comments inside the common header
file to provide information about the APIs exposed by the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 5d097109257c03a71845729f8db6b5770c4bbedc
("tun: only queue packets on device"), NETDEV_TX_OK was returned for
dropped packets. This will confuse pktgen since dropped packets were
counted as sent ones.
Fixing this by returning NET_XMIT_DROP to let pktgen count it as error
packet.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
this is a pull request of 9 patches for net-next/master.
All 9 patches are by Roger Quadros and update the c_can platform
driver. First by improving the initialization sequence of the message
RAM, making use of syscon/regmap. In the later patches support for
various TI SoCs is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return value of swap_buffer() is not used by any caller, thus
remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate the DIV_ROUND_UP() and change the loop counter increment to
4 instead. This results in saving 6 instructions in the functions
assembly code.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when swap_buffer() is being called, we know for sure, that we need to
byte swap the data. Furthermore, this function is called for swapping
data in both directions. Thus cpu_to_be32() is semantically not
correct for all use cases. Use swab32s() to reflect this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fec_enet_private struct
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fep->bufdesc_ex is treated as a boolean value, thus declare it as
such.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
consistently use TABs for indentation
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.
This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.
Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When PFC is enabled we should not proceed with setting the link flow control
parameters. Also, always report the link flow Tx/Rx settings as off when
PFC is enabled.
Change-ID: Ib09ec58afdf0b2e587ac9d8851a5c80ad58206c4
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
FCoE VSI Tx queue disable times out when reconfiguring as a result of
DCB TC configuration change event.
The hardware allows us to skip disabling and enabling of Tx queues for
VSIs with single TC enabled. As FCoE VSI is configured to have only
single TC we skip it from disable/enable flow.
Change-ID: Ia73ff3df8785ba2aa3db91e6f2c9005e61ebaec2
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When DCB TC configuration changes the firmware suspends the port's Tx.
Now, as DCB TCs may have changed the PF driver tries to reconfigure the
TC configuration of the VSIs it manages. As part of this process it disables
the VSI queues but the Tx queue disable will not complete as the port's
Tx has been suspended. So, waiting for Tx queues to go to disable state
in this flow may lead to detection of Tx queue disable timeout errors.
Hence, this patch adds a new PF state so that if a port's Tx is in
suspended state the Tx queue disable flow would just put the request for
the queue to be disabled and return without waiting for the queue to be
actually disabled.
Once the VSI(s) TC reconfiguration has been done and driver has called
firmware AQC "Resume PF Traffic" the driver checks the Tx queues requested
to be disabled are actually disabled before re-enabling them again.
Change-ID: If3e03ce4813a4e342dbd5a1eb1d2861e952b7544
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the port TC configuration changes as a result of DCBx the driver
modifies the enabled TCs for the VEBs it manages. But, in the process
it did not update the enabled_tc value that it caches on a per VEB basis.
So, when the next reconfiguration event occurs where the number of TC
value is same as the value cached in enabled_tc for a given VEB; driver
does not modify it's TC configuration by calling appropriate AQ command
believing it is running with the same configuration as requested.
Now, as the VEB is not actually enabled for the TCs that are there any
TC configuration command for VSI attached to that VEB with TCs that are
not enabled for the VEB fails.
This patch fixes this issue.
Change-ID: Ife5694469b05494228e0d850429ea1734738cf29
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a check whether LLDP Agent's default AdminStatus is
enabled or disabled on a given port. If it is disabled then it sets
the DCBX status to disabled as well; and would not query firmware for
any DCBX configuration data.
Change-ID: I73c0b9f0adbf4cae177d14914b20a48c9a8f50fd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.
Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.
This patch adds this call to the flow that handles DCB re-configuration in
the PF.
Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bumping minor version as this will be the second SW release and it
should be 1.
Change-ID: If0bd102095d2f059ae0c9b7f4ad625535ffbbdee
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
VF interrupt processing takes a looooong time, and it's possible that we
could lose a VFLR event if it happens while we're processing a VFLR on
another VF. This would leave the VF in a semi-permanent reset state,
which would not be cleared until yet another VF experiences a VFLR.
To correct this situation, we enable the VFLR interrupt cause before we
begin processing any pending resets. This means that any VFLR that
occurs during reset processing will generate another interrupt and this
routine will get called again.
This change may cause a spurious interrupt when multiple VFLRs occur
very close together in time. If this happens, then this routine will be
called again and it will detect no outstanding VFLR events and do
nothing. No harm, no foul.
Change-ID: Id0451f3e6e73a2cf6db1668296c71e129b59dc19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Only warn once that PTP is not supported when linked at 100Mbit.
Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports. That should be plenty.
Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Also provide ethtool -x support to fetch RSS key
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Rename rss_hkey local variable to rss_key to have consistent name among
drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_rss_key_fill() helper, as it provides better support for some
bonding setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lendacky, Thomas <Thomas.Lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The infrastructure can now report switch registers to ethtool.
Add support for it to the mv88e6171 driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This chip also has a temperature sensor which can be read using the
common code. In order to use it, add the needed mutex protection for
accessing registers via the shared code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method to read the temperature used in the mve6123_61_65 driver
can also be used for other chips. Move the code into the shared code
base of mv88e6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|