| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
local_addr.svm_cid is host cid. We should check guest cid instead,
which is remote_addr.svm_cid. Otherwise we end up resetting all
connections to all guests.
Cc: stable@vger.kernel.org [4.8+]
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-08
this is a pull request for one patch.
Jiho Chu found and fixed a use-after-free error in the cleanup path in
the peak pcan USB CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes: 2869b23e4b95 ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix for bad memory access while disconnecting. netdev is freed before
private data free, and dev is accessed after freeing netdev.
This makes a slub problem, and it raise kernel oops with slub debugger
config.
Signed-off-by: Jiho Chu <jiho.chu@samsung.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit 3e3aaf649416 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf649416 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063ea ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) When dcbnl_cee_fill() fails to be able to push a new netlink
attribute, it return 0 instead of an error code. From Pan Bian.
2) Two suffix handling fixes to FIB trie code, from Alexander Duyck.
3) bnxt_hwrm_stat_ctx_alloc() goes through all the trouble of setting
and maintaining a return code 'rc' but fails to actually return it.
Also from Pan Bian.
4) ping socket ICMP handler needs to validate ICMP header length, from
Kees Cook.
5) caif_sktinit_module() has this interesting logic:
int err = sock_register(...);
if (!err)
return err;
return 0;
Just return sock_register()'s return value directly which is the
only possible correct thing to do.
6) Two bnx2x driver fixes from Yuval Mintz, return a reasonable
estimate from get_ringparam() ethtool op when interface is down and
avoid trying to use UDP port based tunneling on 577xx chips.
7) Fix ep93xx_eth crash on module unload from Florian Fainelli.
8) Missing uapi exports, from Stephen Hemminger.
9) Don't schedule work from sk_destruct(), because the socket will be
freed upon return from that function. From Herbert Xu.
10) Buggy drivers, of which we know there is at least one, can send a
huge packet into the TCP stack but forget to set the gso_size in the
SKB, which causes all kinds of problems.
Correct this when it happens, and emit a one-time warning with the
device name included so that it can be diagnosed more easily.
From Marcelo Ricardo Leitner.
11) virtio-net does DMA off the stack causes hiccups with VMAP_STACK,
fix from Andy Lutomirski.
12) Fix fec driver compilation with CONFIG_M5272, from Nikita
Yushchenko.
13) mlx5 fixes from Kamal Heib, Saeed Mahameed, and Mohamad Haj Yahia.
(erroneously flushing queues on error, module parameter validation,
etc)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
net/mlx5e: Change the SQ/RQ operational state to positive logic
net/mlx5e: Don't flush SQ on error
net/mlx5e: Don't notify HW when filling the edge of ICO SQ
net/mlx5: Fix query ISSI flow
net/mlx5: Remove duplicate pci dev name print
net/mlx5: Verify module parameters
net: fec: fix compile with CONFIG_M5272
be2net: Add DEVSEC privilege to SET_HSW_CONFIG command.
virtio-net: Fix DMA-from-the-stack in virtnet_set_mac_address()
tcp: warn on bogus MSS and try to amend it
uapi glibc compat: fix outer guard of net device flags enum
net: stmmac: clear reset value of snps, wr_osr_lmt/snps, rd_osr_lmt before writing
netlink: Do not schedule work from sk_destruct
uapi: export nf_log.h
uapi: export tc_skbmod.h
net: ep93xx_eth: Do not crash unloading module
bnx2x: Prevent tunnel config for 577xx
bnx2x: Correct ringparam estimate when DOWN
isdn: hisax: set error code on failure
net: bnx2x: fix improper return value
...
|
|
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4bd ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52a7 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4bd ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743dc ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b1c ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1ee ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 80cca775cdc4 ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cdc4 ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS. Copy the address to the heap
to prevent the crash.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
writing
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we unload the ep93xx_eth, whether we have opened the network
interface or not, we will either hit a kernel paging request error, or a
simple NULL pointer de-reference because:
- if ep93xx_open has been called, we have created a valid DMA mapping
for ep->descs, when we call ep93xx_stop, we also call
ep93xx_free_buffers, ep->descs now has a stale value
- if ep93xx_open has not been called, we have a NULL pointer for
ep->descs, so performing any operation against that address just won't
work
Fix this by adding a NULL pointer check for ep->descs which means that
ep93xx_free_buffers() was able to successfully tear down the descriptors
and free the DMA cookie as well.
Fixes: 1d22e05df818 ("[PATCH] Cirrus Logic ep93xx ethernet driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the 578xx adapters are capable of configuring UDP ports for
the purpose of tunnelling - doing the same on 577xx might lead to
a firmware assertion.
We're already not claiming support for any related feature for such
devices, but we also need to prevent the configuration of the UDP
ports to the device in this case.
Fixes: f34fa14cc033 ("bnx2x: Add vxlan RSS support")
Reported-by: Anikina Anna <anikina@gmail.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.
This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.
To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function hfc4s8s_probe(), the value of return variable err should be
negative on failures. However, when the call to request_region() returns
NULL, the value of err is 0. This patch fixes the bug, assigning
"-EBUSY" to err on the path that request_region() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188931
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Macro BNX2X_ALLOC_AND_SET(arr, lbl, func) calls kmalloc() to allocate
memory, and jumps to label "lbl" if the allocation fails. Label "lbl"
first cleans memory and then returns variable rc. Before calling the
macro, the value of variable rc is 0. Because 0 means no error, the
callers of bnx2x_init_firmware() may be misled. This patch fixes the bug,
assigning "-ENOMEM" to rc before calling macro NX2X_ALLOC_AND_SET().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189141
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling dma_mapping_error(), the value of return variable rc is 0.
And when the call returns an unexpected value, rc is not set to a
negative errno. Thus, it will return 0 on the error path, and its
callers cannot detect the bug. This patch fixes the bug, assigning
"-ENOMEM" to err.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189041
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It returns variable "error" when ioremap_nocache() returns a NULL
pointer. The value of "error" is 0 then, which will mislead the callers
to believe that there is no error. This patch fixes the bug, returning
"-ENOMEM".
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189021
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the calls to kzalloc() fail, the value of return variable ret may
be 0. 0 means success in this context. This patch fixes the bug,
assigning "-ENOMEM" to ret before calling kzalloc().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188971
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function lanai_dev_open(), when the call to ioremap() fails, the
value of return variable result is 0. 0 means no error in this context.
This patch fixes the bug, assigning "-ENOMEM" to result when ioremap()
returns a NULL pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188791
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function lan78xx_probe(), variable ret takes the errno code on
failures. However, when the call to usb_alloc_urb() fails, its value
will keeps 0. 0 indicates success in the context, which is inconsistent
with the execution result. This patch fixes the bug, assigning
"-ENOMEM" to ret when usb_alloc_urb() returns a NULL pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188771
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function bnxt_hwrm_stat_ctx_alloc() always returns 0, even if the call
to _hwrm_send_message() fails. It may be better to propagate the errors
to the caller of bnxt_hwrm_stat_ctx_alloc().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188661
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Intermittent build failure in RSA
- Memory corruption in chelsio crypto driver
- Regression in DRBG due to vmalloced stack"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: rsa - Add Makefile dependencies to fix parallel builds
crypto: chcr - Fix memory corruption
crypto: drbg - prevent invalid SG mappings
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A pretty small pull request: a couple of AMD powerxpress regression
fixes and a power management fix, a couple of i915 fixes and one hdlcd
fix, along with one core don't oops because of incorrect API usage fix"
* tag 'drm-fixes-for-v4.9-rc8' of git://people.freedesktop.org/~airlied/linux:
drm/i915: drop the struct_mutex when wedged or trying to reset
drm/i915: Don't touch NULL sg on i915_gem_object_get_pages_gtt() error
drm: Don't call drm_for_each_crtc with a non-KMS driver
drm/radeon: fix check for port PM availability
drm/amdgpu: fix check for port PM availability
drm/amd/powerplay: initialize the soft_regs offset in struct smu7_hwmgr
drm: hdlcd: Fix cleanup order
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
2 intel fixes.
* tag 'drm-intel-fixes-2016-12-01' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: drop the struct_mutex when wedged or trying to reset
drm/i915: Don't touch NULL sg on i915_gem_object_get_pages_gtt() error
|
|
Pull networking fixes from David Miller:
1) Lots more phydev and probe error path leaks in various drivers by
Johan Hovold.
2) Fix race in packet_set_ring(), from Philip Pettersson.
3) Use after free in dccp_invalid_packet(), from Eric Dumazet.
4) Signnedness overflow in SO_{SND,RCV}BUFFORCE, also from Eric
Dumazet.
5) When tunneling between ipv4 and ipv6 we can be left with the wrong
skb->protocol value as we enter the IPSEC engine and this causes all
kinds of problems. Set it before the output path does any
dst_output() calls, from Eli Cooper.
6) bcmgenet uses wrong device struct pointer in DMA API calls, fix from
Florian Fainelli.
7) Various netfilter nat bug fixes from FLorian Westphal.
8) Fix memory leak in ipvlan_link_new(), from Gao Feng.
9) Locking fixes, particularly wrt. socket lookups, in l2tp from
Guillaume Nault.
10) Avoid invoking rhash teardowns in atomic context by moving netlink
cb->done() dump completion from a worker thread. Fix from Herbert
Xu.
11) Buffer refcount problems in tun and macvtap on errors, from Jason
Wang.
12) We don't set Kconfig symbol DEFAULT_TCP_CONG properly when the user
selects BBR. Fix from Julian Wollrath.
13) Fix deadlock in transmit path on altera TSE driver, from Lino
Sanfilippo.
14) Fix unbalanced reference counting in dsa_switch_tree, from Nikita
Yushchenko.
15) tc_tunnel_key needs to be properly exported to userspace via uapi,
fix from Roi Dayan.
16) rds_tcp_init_net() doesn't unregister notifier in error path, fix
from Sowmini Varadhan.
17) Stale packet header pointer access after pskb_expand_head() in
genenve driver, fix from Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
geneve: avoid use-after-free of skb->data
tipc: check minimum bearer MTU
net: renesas: ravb: unintialized return value
sh_eth: remove unchecked interrupts for RZ/A1
net: bcmgenet: Utilize correct struct device for all DMA operations
NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
cdc_ether: Fix handling connection notification
ip6_offload: check segs for NULL in ipv6_gso_segment.
RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
ipv6: Set skb->protocol properly for local output
ipv4: Set skb->protocol properly for local output
packet: fix race condition in packet_set_ring
net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
net: ethernet: stmmac: platform: fix outdated function header
net: ethernet: stmmac: dwmac-meson8b: fix probe error path
net: ethernet: stmmac: dwmac-generic: fix probe error path
...
|
|
geneve{,6}_build_skb can end up doing a pskb_expand_head(), which
makes the ip_hdr(skb) reference we stashed earlier stale. Since it's
only needed as an argument to ip_tunnel_ecn_encap(), move this
directly in the function call.
Fixes: 08399efc6319 ("geneve: ensure ECN info is handled properly in all tx/rx paths")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-02
this is a pull request for net/master.
There are two patches by Stephane Grosjean, who adds support for the new
PCAN-USB X6 USB interface to the pcan_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to set the other "err" variable here so that we can return it
later. My version of GCC misses this issue but I caught it with a
static checker.
Fixes: 9f70eb339f52 ("net: ethernet: renesas: ravb: fix fixed-link phydev leaks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When streaming a lot of data and the RZ/A1 can't keep up, some status bits
will get set that are not being checked or cleared which cause the
following messages and the Ethernet driver to stop working. This
patch fixes that issue.
irq 21: nobody cared (try booting with the "irqpoll" option)
handlers:
[<c036b71c>] sh_eth_interrupt
Disabling IRQ #21
Fixes: db893473d313a4ad ("sh_eth: Add support for r7s72100")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__bcmgenet_tx_reclaim() and bcmgenet_free_rx_buffers() are not using the
same struct device during unmap that was used for the map operation,
which makes DMA-API debugging warn about it. Fix this by always using
&priv->pdev->dev throughout the driver, using an identical device
reference for all map/unmap calls.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for PID 0x1040 of Telit LE922A.
The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bfe9b9d2df66 ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduced a work-around in usbnet_cdc_status() for devices that exported
cdc carrier on twice on connect. Before the commit, this behavior caused
the link state to be incorrect. It was assumed that all CDC Ethernet
devices would either export this behavior, or send one off and then one on
notification (which seems to be the default behavior).
Unfortunately, it turns out multiple devices sends a connection
notification multiple times per second (via an interrupt), even when
connection state does not change. This has been observed with several
different USB LAN dongles (at least), for example 13b1:0041 (Linksys).
After bfe9b9d2df66, the link state has been set as down and then up for
each notification. This has caused a flood of Netlink NEWLINK messages and
syslog to be flooded with messages similar to:
cdc_ether 2-1:2.0 eth1: kevent 12 may have been dropped
This commit fixes the behavior by reverting usbnet_cdc_status() to how it
was before bfe9b9d2df66. The work-around has been moved to a separate
status-function which is only called when a known, affect device is
detected.
v1->v2:
* Do not open-code netif_carrier_ok() (thanks Henning Schild).
* Call netif_carrier_off() instead of usb_link_change(). This prevents
calling schedule_work() twice without giving the work queue a chance to be
processed (thanks Bjørn Mork).
Fixes: bfe9b9d2df66 ("cdc_ether: Improve ZTE MF823/831/910 handling")
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"Here is the revert for the regression of the i2c-octeon driver I
mentioned last time. I wished for a bit more feedback, but all people
working actively on it are in need of this patch, so here it goes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: octeon: thunderx: Limit register access retries"
|
|
The driver already uses its private lock for synchronization between xmit
and xmit completion handler making the additional use of the xmit_lock
unnecessary.
Furthermore the driver does not set NETIF_F_LLTX resulting in xmit to be
called with the xmit_lock held and then taking the private lock while xmit
completion handler does the reverse, first take the private lock, then the
xmit_lock.
Fix these issues by not taking the xmit_lock in the tx completion handler.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An explicit dma sync for device directly after mapping as well as an
explicit dma sync for cpu directly before unmapping is unnecessary and
costly on the hotpath. So remove these calls.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
