summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2015-05-14net: phy: mdio-gpio: Handle phy_ignore_ta_maskFlorian Fainelli1-2/+5
Update mdiobb_read() to read whether the PHY has a broken turn-around, and if it does, ignore it to make the read succeeed. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-14of: mdio: Add a "broken-turn-around" propertyFlorian Fainelli1-0/+3
Some Ethernet PHY devices/switches may not properly release the MDIO bus during turn-around time, and fail to drive it low, which can be seen by some controllers as a read failure, while the data clocked in is still correct. Add a boolean property "broken-turn-around" which is parsed by the generic MDIO bus probing code and will set the corresponding bit in the MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that information. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-14be2net: Support for OS2BMC.Venkata Duvvuru4-1/+181
OS2BMC feature will allow the server to communicate with the on-board BMC/idrac (Baseboard Management Controller) over the LOM via standard Ethernet. When OS2BMC feature is enabled, the LOM will filter traffic coming from the host. If the destination MAC address matches the iDRAC MAC address, it will forward the packet to the NC-SI side band interface for iDRAC processing. Otherwise, it would send it out on the wire to the external network. Broadcast and multicast packets are sent on the side-band NC-SI channel and on the wire as well. Some of the packet filters are not supported in the NIC and hence driver will identify such packets and will hint the NIC to send those packets to the BMC. This is done by duplicating packets on the management ring. Packets are sent to the management ring, by setting mgmt bit in the wrb header. The NIC will forward the packets on the management ring to the BMC through the side-band NC-SI channel. Please refer to this online document for more details, http://www.dell.com/downloads/global/products/pedge/ os_to_bmc_passthrough_a_new_chapter_in_system_management.pdf Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-14be2net: Report a "link down" to the stack when a fatal error or fw reset ↵Venkata Duvvuru3-34/+49
happens. When an error (related to HW or FW) is detected on a function, the driver must pro-actively report a "link down" to the stack so that a possible failover can be initiated. This is being done currently only for some HW errors. This patch reports a "link down" even for fatal FW errors and EEH errors. Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-14be2net: Export board temperature using hwmon-sysfs interface.Venkata Duvvuru4-3/+46
Ethtool statistics is not the right place to display board temperature. This patch adds support to export die temperature of devices supported by be2net driver via the sysfs hwmon interface. Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-14net: macb: OR vs AND typosDan Carpenter1-4/+4
The bitwise tests are always true here because it uses '|' where '&' is intended. Fixes: 98b5a0f4a228 ('net: macb: Add support for jumbo frames') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13geneve: add initial netdev driver for GENEVE tunnelsJohn W. Linville3-0/+518
This is an initial implementation of a netdev driver for GENEVE tunnels. This implementation uses a fixed UDP port, and only supports point-to-point links with specific partner endpoints. Only IPv4 links are supported at this time. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13flow_dissector: change port array into src, dst tupleJiri Pirko2-4/+4
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13flow_dissect: use programable dissector in skb_flow_dissect and friendsJiri Pirko4-31/+32
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13net: change name of flow_dissector header to match the .c file nameJiri Pirko2-2/+2
add couple of empty lines on the way. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13sfc: suppress some MCDI error messages in PTPEdward Cree1-11/+16
Also, remove a needless netif_err() from efx_ptp_update_stats() - if the MCDI fails it'll print its own error message, we don't need another that adds no information. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13sfc: nicer log message on PTP probe failEdward Cree1-1/+6
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller209-3576/+3191
Four minor merge conflicts: 1) qca_spi.c renamed the local variable used for the SPI device from spi_device to spi, meanwhile the spi_set_drvdata() call got moved further up in the probe function. 2) Two changes were both adding new members to codel params structure, and thus we had overlapping changes to the initializer function. 3) 'net' was making a fix to sk_release_kernel() which is completely removed in 'net-next'. 4) In net_namespace.c, the rtnl_net_fill() call for GET operations had the command value fixed, meanwhile 'net-next' adjusted the argument signature a bit. This also matches example merge resolutions posted by Stephen Rothwell over the past two days. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13fix missing copy_from_user in macvtapJustin Cormack1-1/+4
Fix missing copy_from_user in macvtap SIOCSIFHWADDR ioctl. Signed-off-by: Justin Cormack <justin@netbsd.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13switchdev: don't use anonymous union on switchdev attr/obj structsScott Feldman1-9/+9
Older gcc versions (e.g. gcc version 4.4.6) don't like anonymous unions which was causing build issues on the newly added switchdev attr/obj structs. Fix this by using named union on structs. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Reported-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13switchdev: sparse warning: pass ipv4 fib dst as network-byte orderScott Feldman1-3/+4
And let driver convert it to host-byte order as needed. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds49-493/+1020
Pull networking fixes from David Miller: 1) Handle max TX power properly wrt VIFs and the MAC in iwlwifi, from Avri Altman. 2) Use the correct FW API for scan completions in iwlwifi, from Avraham Stern. 3) FW monitor in iwlwifi accidently uses unmapped memory, fix from Liad Kaufman. 4) rhashtable conversion of mac80211 station table was buggy, the virtual interface was not taken into account. Fix from Johannes Berg. 5) Fix deadlock in rtlwifi by not using a zero timeout for usb_control_msg(), from Larry Finger. 6) Update reordering state before calculating loss detection, from Yuchung Cheng. 7) Fix off by one in bluetooth firmward parsing, from Dan Carpenter. 8) Fix extended frame handling in xiling_can driver, from Jeppe Ledet-Pedersen. 9) Fix CODEL packet scheduler behavior in the presence of TSO packets, from Eric Dumazet. 10) Fix NAPI budget testing in fm10k driver, from Alexander Duyck. 11) macvlan needs to propagate promisc settings down the the lower device, from Vlad Yasevich. 12) igb driver can oops when changing number of rings, from Toshiaki Makita. 13) Source specific default routes not handled properly in ipv6, from Markus Stenberg. 14) Use after free in tc_ctl_tfilter(), from WANG Cong. 15) Use softirq spinlocking in netxen driver, from Tony Camuso. 16) Two ARM bpf JIT fixes from Nicolas Schichan. 17) Handle MSG_DONTWAIT properly in ring based AF_PACKET sends, from Mathias Kretschmer. 18) Fix x86 bpf JIT implementation of FROM_{BE16,LE16,LE32}, from Alexei Starovoitov. 19) ll_temac driver DMA maps TX packet header with incorrect length, fix from Michal Simek. 20) We removed pm_qos bits from netdevice.h, but some indirect references remained. Kill them. From David Ahern. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits) net: Remove remaining remnants of pm_qos from netdevice.h e1000e: Add pm_qos header net: phy: micrel: Fix regression in kszphy_probe net: ll_temac: Fix DMA map size bug x86: bpf_jit: fix FROM_BE16 and FROM_LE16/32 instructions netns: return RTM_NEWNSID instead of RTM_GETNSID on a get Update be2net maintainers' email addresses net_sched: gred: use correct backlog value in WRED mode pppoe: drop pppoe device in pppoe_unbind_sock_work net: qca_spi: Fix possible race during probe net: mdio-gpio: Allow for unspecified bus id af_packet / TX_RING not fully non-blocking (w/ MSG_DONTWAIT). bnx2x: limit fw delay in kdump to 5s after boot ARM: net: delegate filter to kernel interpreter when imm_offset() return value can't fit into 12bits. ARM: net fix emit_udiv() for BPF_ALU | BPF_DIV | BPF_K intruction. mpls: Change reserved label names to be consistent with netbsd usbnet: avoid integer overflow in start_xmit netxen_nic: use spin_[un]lock_bh around tx_clean_lock (2) net: xgene_enet: Set hardware dependency net: amd-xgbe: Add hardware dependency ...
2015-05-12e1000e: Add pm_qos headerDavid Ahern1-0/+1
Commit e2c6544829f moved pm_qos_req to e1000_adapter. Add the header file that defines the struct. Signed-off-by: David Ahern <dsahern@gmail.com> Cc: Thomas Graf <tgraf@suug.ch> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12net: phy: micrel: Fix regression in kszphy_probeNiklas Cassel1-1/+2
Don't do clock-mode-select if clk == NULL, since when building without CONFIG_HAVE_CLK, clk_get returns NULL and clk_get_rate returns 0. Doing clock-mode-select in this cause causes kszphy_probe to return -EINVAL and thus prevents the device from being probed. The original code (before regression) would return 0 when building without CONFIG_HAVE_CLK. Cc: stable <stable@vger.kernel.org> # 3.18+ Fixes: 1fadee0c3645 ("net/phy: micrel: Add clock support for KSZ8021/KSZ8031") Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Niklas Cassel <niklass@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12net: ll_temac: Fix DMA map size bugMichal Simek1-2/+2
DMA allocates skb->len instead of headlen which is used for DMA. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12cxgb4/cxgb4vf: Cleanup macros, add comments and add new MACROSHariprasad Shenai9-147/+235
Cleanup few MACROS left out in t4_hw.h to be consistent with the existing ones. Also replace few hardcoded values with MACROS. Also update comments for some code Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12hv_netvsc: Use the xmit_more skb flag to optimize signaling the hostKY Srinivasan1-16/+27
Based on the information given to this driver (via the xmit_more skb flag), we can defer signaling the host if more packets are on the way. This will help make the host more efficient since it can potentially process a larger batch of packets. Implement this optimization. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12net: systemport: Implement RX coalescing control knobsFlorian Fainelli2-7/+22
Similarly to the TX path, allow the RX path to be configured with both 'rx-frames' and 'rx-usecs' coalescing parameters. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12net: systemport: Implement TX coalescing control knobsFlorian Fainelli1-0/+48
Add the ability to configure both 'tx-frames' which controls how many frames are doing to trigger a single interrupt and 'tx-usecs' which dictates how long to wait before an interrupt should be services. Since our timer resolution is close to 8.192 us, we round up to the nearest value the 'tx-usecs' timeout value. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12macvtap add missing ioctls - fix wrappingJustin Cormack1-0/+29
The macvtap driver tries to emulate all the ioctls supported by a normal tun/tap driver, however it was missing the generic SIOCGIFHWADDR and SIOCSIFHWADDR ioctls to get and set the mac address that are supported by tun/tap. This patch adds these. Signed-off-by: Justin Cormack <justin@netbsd.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12Merge tag 'for-linus' of ↵Linus Torvalds8-18/+18
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma Pull rdma fixes from Doug Ledford: - update MAINTAINERS git repo pointer - printk garbage fix - fix for qib and iw_cxgb4 bugs introduced in 4.1 window - fix for an older iWARP netlink bug - fix a memcpy issue in ehca driver * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: infiniband: Remove duplicated KERN_<LEVEL> from pr_<level> uses IB/qib: fix test of unsigned variable RDMA/core: Fix for parsing netlink string attribute MAINTAINERS: update the official rdma git repo iw_cxgb4: use wildcard mapping for getting remote addr info IB/ehca: use correct destination for memcpy
2015-05-12Merge tag 'for-v4.1-rc' of git://git.infradead.org/battery-2.6Linus Torvalds6-18/+16
Pull power supply and reset fixes from Sebastian Reichel: "misc fixes" * tag 'for-v4.1-rc' of git://git.infradead.org/battery-2.6: power: bq27x00_battery: Add missing MODULE_ALIAS power: reset: Add MFD_SYSCON depends for brcmstb power: reset: ltc2952: Remove bogus hrtimer_start() return value checks power_supply: fix oops in collie_battery driver power/reset: at91: fix return value check in at91_reset_platform_probe() MAINTAINERS: Add me as maintainer of Nokia N900 power supply drivers axp288_fuel_gauge: Add original author details
2015-05-12rocker: make checkpatch -f cleanScott Feldman2-24/+23
Well almost clean: ignore the CHECKs for space after cast operator and some longer-than-80 char cases where for readability it's better to keep as-is. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: remove NETIF_F_HW_SWITCH_OFFLOAD feature flagScott Feldman3-7/+3
Roopa said remove the feature flag for this series and she'll work on bringing it back if needed at a later date. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: convert fib_ipv4_add/del over to switchdev_port_obj_add/delScott Feldman1-27/+14
The IPv4 FIB ops convert nicely to the switchdev objs and we're left with only four switchdev ops: port get/set and port add/del. Other objs will follow, such as FDB. So go ahead and convert IPv4 FIB over to switchdev obj for consistency, anticipating more objs to come. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: cut over to new switchdev_port_bridge_getlinkScott Feldman3-14/+3
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: cut over to new switchdev_port_bridge_dellinkScott Feldman3-2/+3
Rocker, bonding and team and switch over to the new switchdev_port_bridge_dellink to avoid duplicating code in each driver. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: cut over to new switchdev_port_bridge_setlinkScott Feldman3-43/+3
Rocker, bonding, and team can now use the switchdev bridge setlink to parse raw netlink; no need to duplicate this code in each driver. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: add bridge port flags attrScott Feldman1-0/+25
rocker: use switchdev get/set attr for bridge port flags Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12rocker: use switchdev add/del obj for bridge port vlansScott Feldman1-7/+123
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: convert STP update to switchdev attr setScott Feldman1-9/+5
STP update is just a settable port attribute, so convert switchdev_port_stp_update to an attr set. For DSA, the prepare phase is skipped and STP updates are only done in the commit phase. This is because currently the DSA drivers don't need to allocate any memory for STP updates and the STP update will not fail to HW (unless something horrible goes wrong on the MDIO bus, in which case the prepare phase wouldn't have been able to predict anyway). Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12rocker: support prepare-commit transaction modelScott Feldman1-249/+451
For rocker, support prepare-commit transaction model for setting attributes (and for adding objects). This requires rocker to preallocate memory needed for the commit up front in the prepare phase. Since rtnl_lock is held between prepare-commit, store the allocated memory on a queue hanging off of the rocker_port. Also, in prepare phase, do everything right up to calling into HW. The same code paths are tranversed in the driver for both prepare and commit phases. In some cases, any state modified in the prepare phase must be reverted before returning so the commit phase makes the same decisions. As a consequence of holding rtnl_lock in process context for all attr sets (and obj adds), all memory is GFP_KERNEL allocated and we don't need to busy spin waiting for the device to complete the command. So the bulk of this patch is simplifying the memory allocations to only use GFP_KERNEL and to remove the nowait flag and busy spin loop. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: convert parent_id_get to switchdev attr getScott Feldman1-5/+12
Switch ID is just a gettable port attribute. Convert switchdev op switchdev_parent_id_get to a switchdev attr. Note: for sysfs and netlink interfaces, SWITCHDEV_ATTR_PORT_PARENT_ID is called with SWITCHDEV_F_NO_RECUSE to limit switch ID user-visiblity to only port netdevs. So when a port is stacked under bond/bridge, the user can only query switch id via the switch ports, but not via the upper devices Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: s/swdev_/switchdev_/Jiri Pirko1-18/+19
Turned out that "switchdev" sticks. So just unify all related terms to use this prefix. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12switchdev: s/netdev_switch_/switchdev_/ and s/NETDEV_SWITCH_/SWITCHDEV_/Jiri Pirko3-9/+9
Turned out that "switchdev" sticks. So just unify all related terms to use this prefix. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12infiniband: Remove duplicated KERN_<LEVEL> from pr_<level> usesJoe Perches3-5/+4
These KERN_<LEVEL> uses are unnecessary with pr_<level> and cause bad logging output so remove them. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2015-05-12IB/qib: fix test of unsigned variableMike Marciniszyn2-2/+3
Commit d4988623cc60 ("IB/qib: use arch_phys_wc_add()") adjusted mtrr inititialization to use the new interface. Unfortunately, the new interface returns a signed value and the patch tested the unsigned wc_cookie. Fix the issue by changing the type of wc_cookie to int. For the success case the ret left at zero to avoid a warning from the caller. For failure wc_cookie is used as the ret. Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2015-05-12RDMA/core: Fix for parsing netlink string attributeTatyana Nikolova1-1/+1
The string iwpm_ulib_name is recorded in a nlmsg as a netlink attribute. Without this fix parsing of the nlmsg by the userspace port mapper service fails because of unknown attribute length, causing the port mapper service not to register the client, which has sent the nlmsg. Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com> Cc: <stable@vger.kernel.org> #v3.16 Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2015-05-12bnx2x, tg3: Replace put_page(virt_to_head_page()) with skb_free_frag()Alexander Duyck2-2/+2
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12hisilicon: Replace put_page(virt_to_head_page()) with skb_free_frag()Alexander Duyck1-1/+1
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12e1000: Replace e1000_free_frag with skb_free_fragAlexander Duyck1-12/+7
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12mvneta: Replace put_page(virt_to_head_page(ptr)) w/ skb_free_fragAlexander Duyck1-1/+1
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12netcp: Replace put_page(virt_to_head_page(ptr)) w/ skb_free_fragAlexander Duyck1-1/+1
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-12igb: Don't use NETDEV_FRAG_PAGE_MAX_SIZE in descriptor calculationAlexander Duyck1-8/+3
This change updates igb so that it will correctly perform the descriptor count calculation. Previously it was taking NETDEV_FRAG_PAGE_MAX_SIZE into account with isn't really correct since a different value is used to determine the size of the pages used for TCP. That is actually determined by SKB_FRAG_PAGE_ORDER. Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-11iw_cxgb4: use wildcard mapping for getting remote addr infoSteve Wise1-8/+8
For listening endpoints bound to the wildcard address, we need to pass the wildcard address mapping to iwpm_get_remote_info() instead of the mapped address of the new child connection. Without this fix, and with iwarp port mapping enabled, each iw_cxgb4 connection that is spawned from a listening endpoint bound to the wildcard address, will generate an annoying dmesg entry about failing to find the remote address mapping info, and the connection state displayed in debugfs under /sys/kernel/debug/iw_cxgb4/<pci-slot-no>/eps will not have the peer's address/port mapping info. The connection still works though. Fixes: 5b6b8fe ("RDMA/cxgb4: Report the actual address of the remote connecting peer") Signed-off-by: Steve Wise <swise@opengridcomputing.com> Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-18 13:05:39 +0000