summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2019-11-08i40e: Fix for ethtool -m issue on X722 NICArkadiusz Kubalewski1-1/+2
This patch contains fix for a problem with command: 'ethtool -m <dev>' which breaks functionality of: 'ethtool <dev>' when called on X722 NIC Disallowed update of link phy_types on X722 NIC Currently correct value cannot be obtained from FW Previously wrong value returned by FW was used and was a root cause for incorrect output of 'ethtool <dev>' command Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08iavf: initialize ITRN registers with correct valuesNicholas Nunley1-2/+2
Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg value for ITR defines") the driver tracks the interrupt throttling intervals in single usec units, although the actual ITRN registers are programmed in 2 usec units. Most register programming flows in the driver correctly handle the conversion, although it is currently not applied when the registers are initialized to their default values. Most of the time this doesn't present a problem since the default values are usually immediately overwritten through the standard adaptive throttling mechanism, or updated manually by the user, but if adaptive throttling is disabled and the interval values are left alone then the incorrect value will persist. Since the intended default interval of 50 usecs (vs. 100 usecs as programmed) performs better for most traffic workloads, this can lead to performance regressions. This patch adds the correct conversion when writing the initial values to the ITRN registers. Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08ice: fix potential infinite loop because loop counter being too smallColin Ian King1-1/+1
Currently the for-loop counter i is a u8 however it is being checked against a maximum value hw->num_tx_sched_layers which is a u16. Hence there is a potential wrap-around of counter i back to zero if hw->num_tx_sched_layers is greater than 255. Fix this by making i a u16. Addresses-Coverity: ("Infinite loop") Fixes: b36c598c999c ("ice: Updates to Tx scheduler code") Signed-off-by: Colin Ian King <colin.king@canonical.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08net: ethernet: octeon_mgmt: Account for second possible VLAN headerAlexander Sverdlin1-1/+1
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account for second possible VLAN header max_mtu must be further reduced. Fixes: 109cc16526c6d ("ethernet/cavium: use core min/max MTU checking") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-07net: hns: Fix the stray netpoll locks causing deadlock in NAPI pathSalil Mehta3-25/+1
This patch fixes the problem of the spin locks, originally meant for the netpoll path of hns driver, causing deadlock in the normal NAPI poll path. The issue happened due to the presence of the stray leftover spin lock code related to the netpoll, whose support was earlier removed from the HNS[1], got activated due to enabling of NET_POLL_CONTROLLER switch. Earlier background: The netpoll handling code originally had this bug(as identified by Marc Zyngier[2]) of wrong spin lock API being used which did not disable the interrupts and hence could cause locking issues. i.e. if the lock were first acquired in context to thread like 'ip' util and this lock if ever got later acquired again in context to the interrupt context like TX/RX (Interrupts could always pre-empt the lock holding task and acquire the lock again) and hence could cause deadlock. Proposed Solution: 1. If the netpoll was enabled in the HNS driver, which is not right now, we could have simply used spin_[un]lock_irqsave() 2. But as netpoll is disabled, therefore, it is best to get rid of the existing locks and stray code for now. This should solve the problem reported by Marc. [1] https://git.kernel.org/torvalds/c/4bd2c03be7 [2] https://patchwork.ozlabs.org/patch/1189139/ Fixes: 4bd2c03be707 ("net: hns: remove ndo_poll_controller") Cc: lipeng <lipeng321@huawei.com> Cc: Yisen Zhuang <yisen.zhuang@huawei.com> Cc: Eric Dumazet <edumazet@google.com> Cc: David S. Miller <davem@davemloft.net> Reported-by: Marc Zyngier <maz@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-07net: usb: qmi_wwan: add support for DW5821e with eSIM supportAleksander Morgado1-0/+1
Exactly same layout as the default DW5821e module, just a different vid/pid. The QMI interface is exposed in USB configuration #1: P: Vendor=413c ProdID=81e0 Rev=03.18 S: Manufacturer=Dell Inc. S: Product=DW5821e-eSIM Snapdragon X20 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-07CDC-NCM: handle incomplete transfer of MTUOliver Neukum1-3/+3
A malicious device may give half an answer when asked for its MTU. The driver will proceed after this with a garbage MTU. Anything but a complete answer must be treated as an error. V2: used sizeof as request by Alexander Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06NFC: st21nfca: fix double freePan Bian1-0/+1
The variable nfcid_skb is not changed in the callee nfc_hci_get_param() if error occurs. Consequently, the freed variable nfcid_skb will be freed again, resulting in a double free bug. Set nfcid_skb to NULL after releasing it to fix the bug. Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: hns3: add compatible handling for command HCLGE_OPC_PF_RST_DONEHuazhong Tan1-1/+17
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will return -EOPNOTSUPP to the driver when received this command. So for this case, it should just print a warning and return success to the caller. Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06Merge tag 'mlx5-fixes-2019-11-06' of ↵David S. Miller4-2/+6
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahamees says: ==================== Mellanox, mlx5 fixes 2019-11-06 This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem. No -stable this time. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06r8169: fix page read in r8168g_mdio_readHeiner Kallweit1-0/+3
Functions like phy_modify_paged() read the current page, on Realtek PHY's this means reading the value of register 0x1f. Add special handling for reading this register, similar to what we do already in r8168g_mdio_write(). Currently we read a random value that by chance seems to be 0 always. Fixes: a2928d28643e ("r8169: use paged versions of phylib MDIO access functions") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: Fix the TX IOC in xmit pathJose Abreu1-30/+34
IOC bit must be only set in the last descriptor. Move the logic up a little bit to make sure it's set in the correct descriptor. Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: Fix TSO descriptor with Enhanced AddressingJose Abreu1-0/+1
When using addressing > 32 bits the TSO first descriptor only has the header so we can't set the payload field for this descriptor. Let's reset the variable so that buffer 2 value is zero. Fixes: a993db88d17d ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: Fix the packet count in stmmac_rx()Jose Abreu1-2/+3
Currently, stmmac_rx() is counting the number of descriptors but it should count the number of packets as specified by the NAPI limit. Fix this. Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: xgmac: Disable MMC interrupts by defaultJose Abreu1-2/+4
MMC interrupts were being enabled, which is not what we want because it will lead to a storm of interrupts that are not handled at all. Fix it by disabling all MMC interrupts for XGMAC. Fixes: b6cdf09f51c2 ("net: stmmac: xgmac: Implement MMC counters") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: xgmac: Disable Flow Control when 1 or more queues are in AVJose Abreu1-0/+2
When in AVB mode we need to disable flow control to prevent MAC from pausing in TX side. Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: xgmac: Fix AV Feature detectionJose Abreu1-1/+1
Fix incorrect precedence of operators. For reference: AV implies AV Feature but RAV implies only RX side AV Feature. As we want full AV features we need to check RAV. Fixes: c2b69474d63b ("net: stmmac: xgmac: Correct RAVSEL field interpretation") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: xgmac: Fix TSA selectionJose Abreu1-0/+1
When we change between Transmission Scheduling Algorithms, we need to clear previous values so that the new chosen algorithm is correctly selected. Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: xgmac: Only get SPH header len if availableJose Abreu1-1/+2
Split Header length is only available when L34T == 0. Fix this by correctly checking if L34T is zero before trying to get Header length. Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: selftests: Prevent false positives in filter testsJose Abreu1-40/+94
In L2 tests that filter packets by destination MAC address we need to prevent false positives that can occur if we add an address that collides with the existing ones. To fix this, lets manually check if the new address to be added is already present in the NIC and use a different one if so. For Hash filtering this also envolves converting the address to the hash. Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: xgmac: bitrev32 returns u32Jose Abreu1-1/+1
The bitrev32 function returns an u32 var, not an int. Fix it. Fixes: 0efedbf11f07 ("net: stmmac: xgmac: Fix XGMAC selftests") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: stmmac: gmac4: bitrev32 returns u32Jose Abreu1-1/+1
The bitrev32 function returns an u32 var, not an int. Fix it. Fixes: 477286b53f55 ("stmmac: add GMAC4 core support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: mscc: ocelot: fix __ocelot_rmw_ix prototypeVladimir Oltean1-1/+1
The "read-modify-write register index" function is declared with a confusing prototype: the "mask" and "reg" arguments are swapped. Fortunately, this does not affect callers so far. Both arguments are u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in the correct order (the one from ocelot_io.c). Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: mscc: ocelot: fix NULL pointer on LAG slave removalClaudiu Manoil1-1/+2
lag_upper_info may be NULL on slave removal. Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: mscc: ocelot: don't handle netdev events for other netdevsClaudiu Manoil1-3/+3
The check that the event is actually for this device should be moved from the "port" handler to the net device handler. Otherwise the port handler will deny bonding configuration for other net devices in the same system (like enetc in the LS1028A) that don't have the lag_upper_info->tx_type restriction that ocelot has. Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net/mlx5e: Use correct enum to determine uplink portDmytro Linkin1-1/+2
For vlan push action, if eswitch flow source capability is enabled, flow source value compared with MLX5_VPORT_UPLINK enum, to determine uplink port. This lead to syndrome in dmesg if try to add vlan push action. For example: $ tc filter add dev vxlan0 ingress protocol ip prio 1 flower \ enc_dst_port 4789 \ action tunnel_key unset pipe \ action vlan push id 20 pipe \ action mirred egress redirect dev ens1f0_0 $ dmesg ... [ 2456.883693] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 5273): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xa9c090) Use the correct enum value MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK. Fixes: bb204dcf39fe ("net/mlx5e: Determine source port properly for vlan push action") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-11-06net/mlx5: DR, Fix memory leak during rule creationAlex Vesker1-0/+2
During rule creation hw_ste_arr was not freed. Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality") Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-11-06net/mlx5: DR, Fix memory leak in modify action destroyAlex Vesker1-0/+1
The rewrite data was no freed. Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality") Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-11-06net/mlx5e: Fix eswitch debug print of max fdb flowRoi Dayan1-1/+1
The value is already the calculation so remove the log prefix. Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-11-06net: bcmgenet: reapply manual settings to the PHYDoug Berger1-1/+4
The phy_init_hw() function may reset the PHY to a configuration that does not match manual network settings stored in the phydev structure. If the phy state machine is polled rather than event driven this can create a timing hazard where the phy state machine might alter the settings stored in the phydev structure from the value read from the BMCR. This commit follows invocations of phy_init_hw() by the bcmgenet driver with invocations of the genphy_config_aneg() function to ensure that the BMCR is written to match the settings held in the phydev structure. This prevents the risk of manual settings being accidentally altered. Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06Revert "net: bcmgenet: soft reset 40nm EPHYs before MAC init"Doug Berger3-69/+73
This reverts commit 1f515486275a08a17a2c806b844cca18f7de5b34. This commit improved the chances of the umac resetting cleanly by ensuring that the PHY was restored to its normal operation prior to resetting the umac. However, there were still cases when the PHY might not be driving a Tx clock to the umac during this window (e.g. when the PHY detects no link). The previous commit now ensures that the unimac receives clocks from the MAC during its reset window so this commit is no longer needed. This commit also has an unintended negative impact on the MDIO performance of the UniMAC MDIO interface because it is used before the MDIO interrupts are reenabled, so it should be removed. Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-06net: bcmgenet: use RGMII loopback for MAC resetDoug Berger2-2/+33
As noted in commit 28c2d1a7a0bf ("net: bcmgenet: enable loopback during UniMAC sw_reset") the UniMAC must be clocked while sw_reset is asserted for its state machines to reset cleanly. The transmit and receive clocks used by the UniMAC are derived from the signals used on its PHY interface. The bcmgenet MAC can be configured to work with different PHY interfaces including MII, GMII, RGMII, and Reverse MII on internal and external interfaces. Unfortunately for the UniMAC, when configured for MII the Tx clock is always driven from the PHY which places it outside of the direct control of the MAC. The earlier commit enabled a local loopback mode within the UniMAC so that the receive clock would be derived from the transmit clock which addressed the observed issue with an external GPHY disabling it's Rx clock. However, when a Tx clock is not available this loopback is insufficient. This commit implements a workaround that leverages the fact that the MAC can reliably generate all of its necessary clocking by enterring the external GPHY RGMII interface mode with the UniMAC in local loopback during the sw_reset interval. Unfortunately, this has the undesirable side efect of the RGMII GTXCLK signal being driven during the same window. In most configurations this is a benign side effect as the signal is either not routed to a pin or is already expected to drive the pin. The one exception is when an external MII PHY is expected to drive the same pin with its TX_CLK output creating output driver contention. This commit exploits the IEEE 802.3 clause 22 standard defined isolate mode to force an external MII PHY to present a high impedance on its TX_CLK output during the window to prevent any contention at the pin. The MII interface is used internally with the 40nm internal EPHY which agressively disables its clocks for power savings leading to incomplete resets of the UniMAC and many instabilities observed over the years. The workaround of this commit is expected to put an end to those problems. Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05NFC: fdp: fix incorrect free objectPan Bian1-1/+1
The address of fw_vsc_cfg is on stack. Releasing it with devm_kfree() is incorrect, which may result in a system crash or other security impacts. The expected object to free is *fw_vsc_cfg. Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05net: qualcomm: rmnet: Fix potential UAF when unregisteringSean Tranchetti1-2/+2
During the exit/unregistration process of the RmNet driver, the function rmnet_unregister_real_device() is called to handle freeing the driver's internal state and removing the RX handler on the underlying physical device. However, the order of operations this function performs is wrong and can lead to a use after free of the rmnet_port structure. Before calling netdev_rx_handler_unregister(), this port structure is freed with kfree(). If packets are received on any RmNet devices before synchronize_net() completes, they will attempt to use this already-freed port structure when processing the packet. As such, before cleaning up any other internal state, the RX handler must be unregistered in order to guarantee that no further packets will arrive on the device. Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05mlx4_core: fix wrong comment about the reason of subtract one from the max_cqesDotan Barak1-2/+1
The reason for the pre-allocation of one CQE is to enable resizing of the CQ. Fix comment accordingly. Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com> Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05net: dsa: bcm_sf2: Fix driver removalFlorian Fainelli1-2/+2
With the DSA core doing the call to dsa_port_disable() we do not need to do that within the driver itself. This could cause an use after free since past dsa_unregister_switch() we should not be accessing any dsa_switch internal structures. Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05net: hns3: Use the correct style for SPDX License IdentifierNishad Kamdar7-7/+7
This patch corrects the SPDX License Identifier style in header files related to Hisilicon network devices. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05bonding: fix state transition issue in link monitoringJay Vosburgh1-22/+22
Since de77ecd4ef02 ("bonding: improve link-status update in mii-monitoring"), the bonding driver has utilized two separate variables to indicate the next link state a particular slave should transition to. Each is used to communicate to a different portion of the link state change commit logic; one to the bond_miimon_commit function itself, and another to the state transition logic. Unfortunately, the two variables can become unsynchronized, resulting in incorrect link state transitions within bonding. This can cause slaves to become stuck in an incorrect link state until a subsequent carrier state transition. The issue occurs when a special case in bond_slave_netdev_event sets slave->link directly to BOND_LINK_FAIL. On the next pass through bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL case will set the proposed next state (link_new_state) to BOND_LINK_UP, but the new_link to BOND_LINK_DOWN. The setting of the final link state from new_link comes after that from link_new_state, and so the slave will end up incorrectly in _DOWN state. Resolve this by combining the two variables into one. Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru> Reported-by: Sha Zhang <zhangsha.zhang@huawei.com> Cc: Mahesh Bandewar <maheshb@google.com> Fixes: de77ecd4ef02 ("bonding: improve link-status update in mii-monitoring") Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-05can: mcp251x: mcp251x_restart_work_handler(): Fix potential force_quit race ↵Timo Schlüßler1-1/+1
condition In mcp251x_restart_work_handler() the variable to stop the interrupt handler (priv->force_quit) is reset after the chip is restarted and thus a interrupt might occur. This patch fixes the potential race condition by resetting force_quit before enabling interrupts. Signed-off-by: Timo Schlüßler <schluessler@krause.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: add missing state changesJeroen Hofstee1-0/+17
While the ti_hecc has interrupts to report when the error counters increase to a certain level and which change state it doesn't handle the case that the error counters go down again, so the reported state can actually be wrong. Since there is no interrupt for that, do update state based on the error counters, when the state is not error active and goes down again. Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: properly report state changesJeroen Hofstee1-74/+88
The HECC_CANES register handles the flags specially, it only updates the flags after a one is written to them. Since the interrupt for frame errors is not enabled an old error can hence been seen when a state interrupt arrives. For example if the device is not connected to the CAN-bus the error warning interrupt will have HECC_CANES indicating there is no ack. The error passive interrupt thereafter will have HECC_CANES flagging that there is a warning level. And if thereafter there is a message successfully send HECC_CANES points to an error passive event, while in reality it became error warning again. In summary, the state is not always reported correctly. So handle the state changes and frame errors separately. The state changes are now based on the interrupt flags and handled directly when they occur. The reporting of the frame errors is still done as before, as a side effect of another interrupt. note: the hecc_clear_bit will do a read, modify, write. So it will not only clear the bit, but also reset all other bits being set as a side affect, hence it is replaced with only clearing the flags. note: The HECC_CANMC_CCR is no longer cleared in the state change interrupt, it is completely unrelated. And use net_ratelimit to make checkpatch happy. Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: add fifo overflow error reportingJeroen Hofstee1-5/+31
When the rx FIFO overflows the ti_hecc would silently drop them since the overwrite protection is enabled for all mailboxes. So disable it for the lowest priority mailbox and return a proper error value when receive message lost is set. Drop the message itself in that case, since it might be partially updated. Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: release the mailbox a bit earlierJeroen Hofstee1-2/+3
Release the mailbox after reading it, so it can be reused a bit earlier. Since "can: rx-offload: continue on error" all pending message bits are cleared directly, so remove clearing them in ti_hecc. Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: keep MIM and MD setJeroen Hofstee1-3/+3
The HECC_CANMIM is set in the xmit path and cleared in the interrupt. Since this is done with a read, modify, write action the register might end up with some more MIM enabled then intended, since it is not protected. That doesn't matter at all, since the tx interrupt disables the mailbox with HECC_CANME (while holding a spinlock). So lets just always keep MIM set. While at it, since the mailbox direction never changes, don't set it every time a message is send, ti_hecc_reset() already sets them to tx. Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: ti_hecc_stop(): stop the CPK on downJeroen Hofstee1-0/+3
When the interface goes down, the CPK should no longer take an active part in the CAN-bus communication, like sending acks and error frames. So enable configuration mode in ti_hecc_stop, so the CPK is no longer active. When a transceiver switch is present the acks and errors don't make it to the bus, but disabling the CPK then does prevent oddities, like ti_hecc_reset() failing, since the CPK can become bus-off and starts counting the 11 bit recessive bits, which seems to block the reset. It can also cause invalid interrupts and disrupt the CAN-bus, since transmission can be stopped in the middle of a message, by disabling the tranceiver while the CPK is sending. Since the CPK is disabled after normal power on, it is typically only seen when the interface is restarted. Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: ti_hecc: ti_hecc_error(): increase error counters if skb enqueueing via ↵Marc Kleine-Budde1-1/+4
can_rx_offload_queue_sorted() fails The call to can_rx_offload_queue_sorted() may fail and return an error (in the current implementation due to resource shortage). The passed skb is consumed. This patch adds incrementing of the appropriate error counters to let the device statistics reflect that there's a problem. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: flexcan: increase error counters if skb enqueueing via ↵Marc Kleine-Budde1-2/+8
can_rx_offload_queue_sorted() fails The call to can_rx_offload_queue_sorted() may fail and return an error (in the current implementation due to resource shortage). The passed skb is consumed. This patch adds incrementing of the appropriate error counters to let the device statistics reflect that there's a problem. Reported-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: rx-offload: can_rx_offload_irq_offload_fifo(): continue on errorMarc Kleine-Budde1-1/+3
In case of a resource shortage, i.e. the rx_offload queue will overflow or a skb fails to be allocated (due to OOM), can_rx_offload_offload_one() will call mailbox_read() to discard the mailbox and return an ERR_PTR. If the hardware FIFO is empty can_rx_offload_offload_one() will return NULL. In case a CAN frame was read from the hardware, can_rx_offload_offload_one() returns the skb containing it. Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb returned, regardless of the reason. Similar to can_rx_offload_irq_offload_timestamp() in case of a resource shortage the whole FIFO should be discarded, to avoid an IRQ storm and give the system some time to recover. However if the FIFO is empty the loop can be left. With this patch the loop is left in case of empty FIFO, but not on errors. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: rx-offload: can_rx_offload_irq_offload_timestamp(): continue on errorJeroen Hofstee1-1/+1
In case of a resource shortage, i.e. the rx_offload queue will overflow or a skb fails to be allocated (due to OOM), can_rx_offload_offload_one() will call mailbox_read() to discard the mailbox and return an ERR_PTR. However can_rx_offload_irq_offload_timestamp() bails out in the error case. In case of a resource shortage all mailboxes should be discarded, to avoid an IRQ storm and give the system some time to recover. Since can_rx_offload_irq_offload_timestamp() is typically called from a while loop, all message will eventually be discarded. So let's continue on error instead to discard them directly. Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04can: rx-offload: can_rx_offload_offload_one(): use ERR_PTR() to propagate ↵Marc Kleine-Budde1-13/+73
error value in case of errors Before this patch can_rx_offload_offload_one() returns a pointer to a skb containing the read CAN frame or a NULL pointer. However the meaning of the NULL pointer is ambiguous, it can either mean the requested mailbox is empty or there was an error. This patch fixes this situation by returning: - pointer to skb on success - NULL pointer if mailbox is empty - ERR_PTR() in case of an error All users of can_rx_offload_offload_one() have been adopted, no functional change intended. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-10 21:57:13 +0000