summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2016-04-05mac80211_hwsim: Support a hw scan request for a specific BSSIDJouni Malinen1-0/+5
If the hw scan request specifies a single BSSID, use that value instead of the wildcard BSSID in the Probe Request frames. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: allow not sending MIC up from driver for HW cryptoSara Sharon2-2/+2
When HW crypto is used, there's no need for the CCMP/GCMP MIC to be available to mac80211, and the hardware might have removed it already after checking. The MIC is also useless to have when the frame is already decrypted, so allow indicating that it's not present. Since we are running out of bits in mac80211_rx_flags, make the flags field a u64. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds45-460/+584
Pull networking fixes from David Miller: 1) Missing device reference in IPSEC input path results in crashes during device unregistration. From Subash Abhinov Kasiviswanathan. 2) Per-queue ISR register writes not being done properly in macb driver, from Cyrille Pitchen. 3) Stats accounting bugs in bcmgenet, from Patri Gynther. 4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from Quentin Armitage. 5) SXGBE driver has off-by-one in probe error paths, from Rasmus Villemoes. 6) Fix race in save/swap/delete options in netfilter ipset, from Vishwanath Pai. 7) Ageing time of bridge not set properly when not operating over a switchdev device. Fix from Haishuang Yan. 8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander Duyck. 9) IPV6 UDP code bumps wrong stats, from Eric Dumazet. 10) FEC driver should only access registers that actually exist on the given chipset, fix from Fabio Estevam. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits) net: mvneta: fix changing MTU when using per-cpu processing stmmac: fix MDIO settings Revert "stmmac: Fix 'eth0: No PHY found' regression" stmmac: fix TX normal DESC net: mvneta: use cache_line_size() to get cacheline size net: mvpp2: use cache_line_size() to get cacheline size net: mvpp2: fix maybe-uninitialized warning tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card rtnl: fix msg size calculation in if_nlmsg_size() fec: Do not access unexisting register in Coldfire net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES net: dsa: mv88e6xxx: Clear the PDOWN bit on setup net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write} bpf: make padding in bpf_tunnel_key explicit ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates bnxt_en: Fix ethtool -a reporting. bnxt_en: Fix typo in bnxt_hwrm_set_pause_common(). bnxt_en: Implement proper firmware message padding. ...
2016-04-01Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds11-45/+45
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fixes from Stephen Boyd: "A handful of const updates for reset ops and a couple fixes to the newly introduced IPQ4019 clock driver" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll clk: qcom: ipq4019: switch remaining defines to enums clk: qcom: Make reset_control_ops const clk: tegra: Make reset_control_ops const clk: sunxi: Make reset_control_ops const clk: atlas7: Make reset_control_ops const clk: rockchip: Make reset_control_ops const clk: mmp: Make reset_control_ops const clk: mediatek: Make reset_control_ops const
2016-04-01Merge tag 'pm+acpi-4.6-rc2' of ↵Linus Torvalds3-0/+61
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management and ACPI fix from Rafael J. Wysocki: "Just one fix for a nasty boot failure on some systems based on Intel Skylake that shipped with broken firmware where enabling hardware-coordinated P-states management (HWP) causes a faulty interrupt handler in SMM to be invoked and crash the system (Srinivas Pandruvada)" * tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI / processor: Request native thermal interrupt handling via _OSC
2016-04-02Merge branch 'acpi-processor'Rafael J. Wysocki3-0/+61
* acpi-processor: ACPI / processor: Request native thermal interrupt handling via _OSC
2016-04-01net: mvneta: fix changing MTU when using per-cpu processingMarcin Wojtas1-14/+16
After enabling per-cpu processing it appeared that under heavy load changing MTU can result in blocking all port's interrupts and transmitting data is not possible after the change. This commit fixes above issue by disabling percpu interrupts for the time, when TXQs and RXQs are reconfigured. Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01stmmac: fix MDIO settingsGiuseppe CAVALLARO3-47/+72
Initially the phy_bus_name was added to manipulate the driver name but it was recently just used to manage the fixed-link and then to take some decision at run-time. So the patch uses the is_pseudo_fixed_link and removes the phy_bus_name variable not necessary anymore. The driver can manage the mdio registration by using phy-handle, dwmac-mdio and own parameter e.g. snps,phy-addr. This patch takes care about all these possible configurations and fixes the mdio registration in case of there is a real transceiver or a switch (that needs to be managed by using fixed-link). Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com> Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Phil Reid <preid@electromag.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01Revert "stmmac: Fix 'eth0: No PHY found' regression"Giuseppe CAVALLARO2-9/+11
This reverts commit 88f8b1bb41c6208f81b6a480244533ded7b59493. due to problems on GeekBox and Banana Pi M1 board when connected to a real transceiver instead of a switch via fixed-link. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org> Cc: Andreas Färber <afaerber@suse.de> Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01stmmac: fix TX normal DESCGiuseppe CAVALLARO1-8/+8
This patch fixs a regression raised when test on chips that use the normal descriptor layout. In fact, no len bits were set for the TDES1 and no OWN bit inside the TDES0. Signed-off-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com> Tested-by: Andreas Färber <afaerber@suse.de> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01net: mvneta: use cache_line_size() to get cacheline sizeJisheng Zhang1-1/+1
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size to determine the cacheline size in runtime. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Suggested-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01net: mvpp2: use cache_line_size() to get cacheline sizeJisheng Zhang1-1/+1
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size to determine the cacheline size in runtime. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Suggested-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01net: mvpp2: fix maybe-uninitialized warningJisheng Zhang1-1/+3
This is to fix the following maybe-uninitialized warning: drivers/net/ethernet/marvell/mvpp2.c:6007:18: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized] Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filterDaniel Borkmann1-3/+5
Sasha Levin reported a suspicious rcu_dereference_protected() warning found while fuzzing with trinity that is similar to this one: [ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage! [ 52.765688] other info that might help us debug this: [ 52.765695] rcu_scheduler_active = 1, debug_locks = 1 [ 52.765701] 1 lock held by a.out/1525: [ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20 [ 52.765721] stack backtrace: [ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264 [...] [ 52.765768] Call Trace: [ 52.765775] [<ffffffff813e488d>] dump_stack+0x85/0xc8 [ 52.765784] [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110 [ 52.765792] [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90 [ 52.765801] [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun] [ 52.765810] [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun] [ 52.765818] [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210 [ 52.765827] [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun] [ 52.765834] [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690 [ 52.765843] [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60 [ 52.765850] [<ffffffff81261519>] SyS_ioctl+0x79/0x90 [ 52.765858] [<ffffffff81003ba2>] do_syscall_64+0x62/0x140 [ 52.765866] [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25 Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH, DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices. Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu fixes") sk_attach_filter()/sk_detach_filter() now dereferences the filter with rcu_dereference_protected(), checking whether socket lock is held in control path. Since its introduction in 994051625981 ("tun: socket filter support"), tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the sock_owned_by_user(sk) doesn't apply in this specific case and therefore triggers the false positive. Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair that is used by tap filters and pass in lockdep_rtnl_is_held() for the rcu_dereference_protected() checks instead. Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-01Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds16-34/+152
Pull drm fixes from Dave Airlie: "Nothing too crazy in here: a bunch of AMD fixes/quirks, two msm fixes, some rockchip fixes, and a udl warning fix, along with one locking fix for displayport that seems to fix some dodgy monitors" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/udl: Use unlocked gem unreferencing drm/dp: move hw_mutex up the call stack drm/amdgpu: Don't move pinned BOs drm/radeon: Don't move pinned BOs drm/radeon: add a dpm quirk for all R7 370 parts drm/radeon: add another R7 370 quirk drm/rockchip: dw_hdmi: Don't call platform_set_drvdata() drm/rockchip: vop: Fix vop crtc cleanup drm/rockchip: dw_hdmi: Call drm_encoder_cleanup() in error path drm/rockchip: vop: Disable planes when disabling CRTC drm/rockchip: vop: Don't reject empty modesets drm/rockchip: cancel pending vblanks on close drm/rockchip: vop: fix crtc size in plane check drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5 drm/amd: Beef up ACP Kconfig menu text drm/msm: fix typo in the !COMMON_CLK case drm/msm: fix bug after preclose removal
2016-04-01Merge branch 'for-linus' of ↵Linus Torvalds4-183/+86
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Martin Schwidefsky: - A proper fix for the locking issue in the dasd driver - Wire up the new preadv2 nad pwritev2 system calls - Add the mark_rodata_ro function and set DEBUG_RODATA=y - A few more bug fixes. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390: wire up preadv2/pwritev2 syscalls s390/pci: PCI function group 0 is valid for clp_query_pci_fn s390/crypto: provide correct file mode at device register. s390/mm: handle PTE-mapped tail pages in fast gup s390: add DEBUG_RODATA support s390: disable postinit-readonly for now s390/dasd: reorder lcu and device lock s390/cpum_sf: Fix cpu hotplug notifier transitions s390/cpum_cf: Fix missing cpu hotplug notifier transition
2016-04-01drm/udl: Use unlocked gem unreferencingDaniel Vetter2-2/+2
For drm_gem_object_unreference callers are required to hold dev->struct_mutex, which these paths don't. Enforcing this requirement has become a bit more strict with commit ef4c6270bf2867e2f8032e9614d1a8cfc6c71663 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Oct 15 09:36:25 2015 +0200 drm/gem: Check locking in drm_gem_object_unreference Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2016-04-01drm/dp: move hw_mutex up the call stackRob Clark1-10/+17
1) don't let other threads trying to bang on aux channel interrupt the defer timeout/logic 2) don't let other threads interrupt the i2c over aux logic Technically, according to people who actually have the DP spec, this should not be required. In practice, it makes some troublesome Dell monitor (and perhaps others) work, so probably a case of "It's compliant if it works with windows" on the hw vendor's part.. v2: rebased to come before DPCD/AUX logging patch for easier backport to stable branches. Reported-by: Dave Wysochanski <dwysocha@redhat.com> Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1274157 Cc: stable@vger.kernel.org Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
2016-04-01Merge branch 'drm-rockchip-next-fixes-2016-03-28' of ↵Dave Airlie4-15/+100
https://github.com/markyzq/kernel-drm-rockchip into drm-fixes bunch of rockchip fixes. * 'drm-rockchip-next-fixes-2016-03-28' of https://github.com/markyzq/kernel-drm-rockchip: drm/rockchip: dw_hdmi: Don't call platform_set_drvdata() drm/rockchip: vop: Fix vop crtc cleanup drm/rockchip: dw_hdmi: Call drm_encoder_cleanup() in error path drm/rockchip: vop: Disable planes when disabling CRTC drm/rockchip: vop: Don't reject empty modesets drm/rockchip: cancel pending vblanks on close drm/rockchip: vop: fix crtc size in plane check
2016-04-01Merge branch 'msm-fixes-4.6-rc1' of ↵Dave Airlie3-5/+1
git://people.freedesktop.org/~robclark/linux into drm-fixes two minor msm fixes. * 'msm-fixes-4.6-rc1' of git://people.freedesktop.org/~robclark/linux: drm/msm: fix typo in the !COMMON_CLK case drm/msm: fix bug after preclose removal
2016-04-01Merge branch 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie6-2/+32
into drm-fixes Just a few fixes for 4.6 this week: - Add some SI DPM quirks - Improve the ACP Kconfig text - Additional BO pinning checks * 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux: drm/amdgpu: Don't move pinned BOs drm/radeon: Don't move pinned BOs drm/radeon: add a dpm quirk for all R7 370 parts drm/radeon: add another R7 370 quirk drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5 drm/amd: Beef up ACP Kconfig menu text
2016-03-31net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband cardDaniele Palmas1-0/+7
Telit LE910 V2 is a mobile broadband card with no ARP capabilities: the patch makes this device to use wwan_noarp_info struct Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Reviewed-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31fec: Do not access unexisting register in ColdfireFabio Estevam1-1/+1
Commit 55cd48c821de ("net: fec: stop the "rcv is not +last, " error messages") introduces a write to a register that does not exist in Coldfire. Move the FEC_FTRL register access inside the FEC_QUIRK_HAS_RACC 'if' block, so that we guarantee it will not be used on Coldfire CPUs. Reported-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTESJisheng Zhang1-9/+1
The mvneta is also used in some Marvell berlin family SoCs which may have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE usage with L1_CACHE_BYTES. And since dma_alloc_coherent() is always cacheline size aligned, so remove the align checks. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTESJisheng Zhang1-13/+1
The mvpp2 ip maybe used in SoCs which may have have 64bytes cacheline size. Replace the MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES. And since dma_alloc_coherent() is always cacheline size aligned, so remove the align checks. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31net: dsa: mv88e6xxx: Clear the PDOWN bit on setupPatrick Uiterwijk2-0/+44
Some of the vendor-specific bootloaders set up this part of the initialization for us, so this was never added. However, since upstream bootloaders don't initialize the chip specifically, they leave the fiber MII's PDOWN flag set, which means that the CPU port doesn't connect. This patch checks whether this flag has been clear prior by something else, and if not make us clear it. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org> Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}Patrick Uiterwijk1-13/+36
Add versions of the phy_page_read and _write functions to be used in a context where the SMI mutex is held. Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31Merge branch '10GbE' of ↵David S. Miller9-121/+107
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2016-03-29 This series contains fixes to ixgbe and ixgbevf. Tushar fixes an issue which was introduced with an earlier commit, where hardware register RAR0 default MAC address does not get set properly. Alex fixes two issues, first being the VXLAN port number should be stored in network order instead of in host order. The second fix corrects the ATR code to handle IPv6 extension headers. The issue was ATR code was assuming that it would be able to use tcp_hdr for every TCP frame that came through, but that is not the case, which resulted in bad filters being setup. Mark fixes a use of usleep_range() to udelay() in the case where a lock is being held. Stefan fixes the offline self tests where ndo_stop() should be used instead of ndo_close(), which causes IFF_UP to be cleared and interface routes get removed. Emil fixes the error case where we need to return an error when a MAC address change is rejected by the PF. This helps prevent the user from modifying the MAC address when the operation is not permitted. Sridhar provides three fixes for ixgbe, all dealing with traffic class offload handling. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-31Merge tag 'gpio-v4.6-2' of ↵Linus Torvalds2-5/+9
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO fixes from Linus Walleij: "Here are two GPIO fixes for the v4.6 series, both in drivers: - Prevent NULL dereference in the Xgene driver - Fix an uninitialized spinlock in the menz127 driver" * tag 'gpio-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio: xgene: Prevent NULL pointer dereference gpio: menz127: Drop lock field from struct men_z127_gpio
2016-03-31Merge branch 'libnvdimm-for-next' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull nvdimm mcsafe_memcpy use from Dan Williams: "Now that mcsafe_memcpy() has landed, and the return value was been clarified in commit cbf8b5a2b649 ("x86/mm, x86/mce: Fix return type/value for memcpy_mcsafe()"), let's hook up its primary usage in the pmem driver. The compilation problems from the initial posting have been fixed, this has appeared in a -next release with no reported issues, and it picked up an ack from Ingo. There is no pressing need to merge this in 4.6- rc2. However, if we wait until 4.7 the new memcpy_mcsafe() capability will ship without a user in 4.6-final" * 'libnvdimm-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: x86, pmem: use memcpy_mcsafe() for memcpy_from_pmem()
2016-03-30bnxt_en: Fix ethtool -a reporting.Michael Chan1-4/+2
To report flow control tx/rx settings accurately regardless of autoneg setting, we should use link_info->req_flow_ctrl. Before this patch, the reported settings were only correct when autoneg was on. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-30bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().Michael Chan1-1/+1
The typo caused the wrong flow control bit to be set. Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-30bnxt_en: Implement proper firmware message padding.Michael Chan2-1/+7
The size of every padded firmware message is specified in the first HWRM_VER_GET response message. Use this value to pad every message after that. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-30bnxt_en: Initialize CP doorbell value before ring allocationPrashant Sreedharan1-1/+1
The existing code does the following: allocate completion ring initialize completion ring doorbell disable interrupts on this completion ring by writing to the doorbell We can have a race where firmware sends an asynchronous event to the host after completion ring allocation and before doorbell is initialized. When this happens driver can crash while ringing the doorbell using uninitialized value as part of handling the IRQ/napi request. Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-30team: team should sync the port's uc/mc addrs when add a portXin Long1-0/+5
There is an issue when we use mavtap over team: When we replug nic links from team0, the real nics's mc list will not include the maddr for macvtap any more. then we can't receive pkts to macvtap device, as they are filterred by mc list of nic. In Bonding Driver, it syncs the uc/mc addrs in bond_enslave(). We will fix this issue on team by adding the port's uc/mc addrs sync in team_port_add. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-30qed: initialize return rc to avoid returning garbageColin Ian King1-1/+1
in the case where qed_slowpath_irq_req is not called, rc is not assigned and so qed_int_igu_enable will return a garbage value. Fix this by initializing rc to 0. Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-30Merge tag 'hwmon-for-linus-v4.6-rc2' of ↵Linus Torvalds1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon fix from Guenter Roeck: "Fix crash due to NULL pointer access in max1111 driver" * tag 'hwmon-for-linus-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (max1111) Return -ENODEV from max1111_read_channel if not instantiated
2016-03-30gpio: xgene: Prevent NULL pointer dereferenceAxel Lin1-0/+5
platform_get_resource() can return NULL, thus add NULL test to prevent NULL pointer dereference. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-30gpio: menz127: Drop lock field from struct men_z127_gpioAxel Lin1-5/+4
Current code uses a uninitialized spin lock. bgpio_init() already initialized a spin lock, so let's switch to use &gc->bgpio_lock instead and remove the lock from struct men_z127_gpio. Fixes: f436bc2726c6 "gpio: add driver for MEN 16Z127 GPIO controller" Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-29ixgbe: Fix cls_u32 offload support for L4 portsSridhar Samudrala1-12/+4
Fix support for 16 bit source/dest port matches in ixgbe model. u32 uses a single 32-bit key value for both source and destination ports starting at offset 0. So replace the 2 functions with a single function that takes this key value/mask to program both source and dest ports. Verified with the following filter: #tc qdisc add dev p4p1 ingress #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 1: u32 divisor 1 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 800:0:10 u32 ht 800: link 1: \ offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 1:0:10 u32 ht 1: \ match tcp src 1024 ffff match tcp dst 80 ffff action drop #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 1:0:11 u32 ht 1: \ match tcp src 1025 ffff action drop #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 1:0:12 u32 ht 1: \ match tcp dst 81 ffff action drop Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: Fix cls_u32 offload support for fields with masksSridhar Samudrala2-7/+5
Remove the incorrect check for mask in ixgbe_configure_clsu32 and drop the 'mask' field that is not required in struct ixgbe_mat_field Verified with the following filters: #tc qdisc add dev p4p1 ingress #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 800:0:1 u32 ht 800: \ match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 800:0:2 u32 ht 800: \ match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 800:0:3 u32 ht 800: \ match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \ handle 800:0:4 u32 ht 800: \ match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: fix error handling in TC cls_u32 offload routinesSridhar Samudrala1-18/+34
Check for handle ids when adding/deleting hash nodes OR adding/deleting filter entries and limit them to max number of links or header nodes supported(IXGBE_MAX_LINK_HANDLE). Start from bit 0 when setting hash table bit-map.(adapter->tables) Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: make __ixgbe_setup_tc staticEmil Tantilov1-2/+2
This function is only used in ixgbe_main.c Resolves a "missing prototype" warning when building the driver with W=1 Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbevf: fix error code path when setting MAC addressEmil Tantilov2-5/+11
Return error when a MAC address change is rejected by the PF. This will prevent the user from modifying the MAC address when that operation is not permitted. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbevf: call ndo_stop() instead of dev_close() when running offline selftestStefan Assmann3-4/+6
Calling dev_close() causes IFF_UP to be cleared which will remove the interfaces routes and some addresses. That's probably not what the user intended when running the offline selftest. Besides this does not happen if the interface is brought down before the test, so the current behaviour is inconsistent. Instead call the net_device_ops ndo_stop function directly and avoid touching IFF_UP at all. Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: call ndo_stop() instead of dev_close() when running offline selftestStefan Assmann3-4/+6
Calling dev_close() causes IFF_UP to be cleared which will remove the interfaces routes and some addresses. That's probably not what the user intended when running the offline selftest. Besides this does not happen if the interface is brought down before the test, so the current behaviour is inconsistent. Instead call the net_device_ops ndo_stop function directly and avoid touching IFF_UP at all. Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: Use udelay to avoid sleeping while atomicMark Rustad1-1/+1
Use udelay instead of usleep_range because this can be called while a lock is held. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: Fix ATR so that it correctly handles IPv6 extension headersAlexander Duyck1-24/+21
The ATR code was assuming that it would be able to use tcp_hdr for every TCP frame that came through. However this isn't the case as it is possible for a frame to arrive that is TCP but sent through something like a raw socket. As a result the driver was setting up bad filters in which tcp_hdr was really pointing to the network header so the data was all invalid. In order to correct this I have added a bit of parsing logic that will determine the TCP header location based off of the network header and either the offset in the case of the IPv4 header, or a walk through the IPv6 extension headers until it encounters the header that indicates IPPROTO_TCP. In addition I have added checks to verify that the lowest protocol provided is recognized as IPv4 or IPv6 to help mitigate raw sockets using ETH_P_ALL from having ATR applied to them. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: Store VXLAN port number in network orderAlexander Duyck2-49/+20
The VXLAN port number should be stored in network order instead of in host order as it is accessed from the hot-path in ATR. This way we can avoid having to do any byte swaps in order to validate the port number. I moved the vxlan_port value into a hole in the read-mostly region of the adapter struct. This way it should be in a warm cache-line instead of in some isolated region in memory when it needs to be accessed. In addition I went through and stripped a bunch of unneeded ifdef flags since having an extra variable present doesn't really hurt anything and makes the code easier to read. I also went through and dropped the NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides no value as the flag is not evaluated in the Rx path. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-03-29ixgbe: Fix for RAR0 not being set to default MAC addrTushar Dave1-0/+2
commit c9f53e63c208 ("ixgbe: Refactor MAC address configuration code") introduced code that doesn't set HW register RAR0 to default mac address but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF. This commit sets RAR0 correctly to default HW mac address. Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com> Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-17 11:34:40 +0000