| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here is one fix, and three documentation updates for 5.18-rc7.
The fix is for the firmware loader which resolves a long-reported
problem where the credentials of the firmware loader could be set to a
userspace process without enough permissions to actually load the
firmware image. Many Android vendors have been reporting this for
quite some time.
The documentation updates are for the embargoed-hardware-issues.rst
file to add a new entry, change an existing one, and sort the list to
make changes easier in the future.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation/process: Update ARM contact for embargoed hardware issues
Documentation/process: Add embargoed HW contact for Ampere Computing
Documentation/process: Make groups alphabetical and use tabs consistently
firmware_loader: use kernel credentials when reading firmware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two small driver fixes for 5.18-rc7 that resolve reported
problems:
- slimbus driver irq bugfix
- interconnect sync state bugfix
Both of these have been in linux-next with no reported problems"
* tag 'char-misc-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
slimbus: qcom: Fix IRQ check in qcom_slim_probe
interconnect: Restore sync state by ignoring ipa-virt in provider count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty n_gsm and serial driver fixes for 5.18-rc7
that resolve reported problems. They include:
- n_gsm fixes for reported issues
- 8250_mtk driver fixes for some platforms
- fsl_lpuart driver fix for reported problem.
- digicolor driver fix for reported problem.
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fsl_lpuart: Don't enable interrupts too early
tty: n_gsm: fix invalid gsmtty_write_room() result
tty: n_gsm: fix mux activation issues in gsm_config()
tty: n_gsm: fix buffer over-read in gsm_dlci_data()
serial: 8250_mtk: Fix register address for XON/XOFF character
serial: 8250_mtk: Make sure to select the right FEATURE_SEL
serial: 8250_mtk: Fix UART_EFR register address
tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small fixes for reported issues with some USB drivers.
They include:
- xhci fixes for xhci-mtk platform driver
- typec driver fixes for reported problems.
- cdc-wdm read-stuck fix
- gadget driver fix for reported race condition
- new usb-serial driver ids
All of these have been in linux-next with no reported problems"
* tag 'usb-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci-mtk: remove bandwidth budget table
usb: xhci-mtk: fix fs isoc's transfer error
usb: gadget: fix race when gadget driver register via ioctl
usb: typec: tcpci_mt6360: Update for BMC PHY setting
usb: gadget: uvc: allow for application to cleanly shutdown
usb: typec: tcpci: Don't skip cleanup in .remove() on error
usb: cdc-wdm: fix reading stuck on device close
USB: serial: qcserial: add support for Sierra Wireless EM7590
USB: serial: option: add Fibocom MA510 modem
USB: serial: option: add Fibocom L610 modem
USB: serial: pl2303: add device id for HP LM930 Display
|
|
Pull more drm fixes from Dave Airlie:
"Turns out I was right, some fixes hadn't made it to me yet. The vmwgfx
ones also popped up later, but all seem like bad enough things to fix.
The dma-buf, vc4 and nouveau ones are all pretty small.
The fbdev fixes are a bit more complicated: a fix to cleanup fbdev
devices properly, uncovered some use-after-free bugs in existing
drivers. Then the fix for those bugs wasn't correct. This reverts that
fix, and puts the proper fixes in place in the drivers to avoid the
use-after-frees.
This has had a fair number of eyes on it at this stage, and I'm
confident enough that it puts things in the right place, and is less
dangerous than reverting our way out of the initial change at this
stage.
fbdev:
- revert NULL deref fix that turned into a use-after-free
- prevent use-after-free in fbdev
- efifb/simplefb/vesafb: fix cleanup paths to avoid use-after-frees
dma-buf:
- fix panic in stats setup
vc4:
- fix hdmi build
nouveau:
- tegra iommu present fix
- fix leak in backlight name
vmwgfx:
- Black screen due to fences using FIFO checks on SVGA3
- Random black screens on boot due to uninitialized drm_mode_fb_cmd2
- Hangs on SVGA3 due to command buffers being used with gbobjects"
* tag 'drm-fixes-2022-05-14' of git://anongit.freedesktop.org/drm/drm:
drm/vmwgfx: Disable command buffers on svga3 without gbobjects
drm/vmwgfx: Initialize drm_mode_fb_cmd2
drm/vmwgfx: Fix fencing on SVGAv3
drm/vc4: hdmi: Fix build error for implicit function declaration
dma-buf: call dma_buf_stats_setup after dmabuf is in valid list
fbdev: efifb: Fix a use-after-free due early fb_info cleanup
drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
drm/nouveau/tegra: Stop using iommu_present()
fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: Prevent possible use-after-free in fb_release()
Revert "fbdev: Make fb_release() return -ENODEV if fbdev was unregistered"
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Multiple fixes to fbdev to address a regression at unregistration, an
iommu detection improvement for nouveau, a memory leak fix for nouveau,
pointer dereference fix for dma_buf_file_release(), and a build breakage
fix for vc4
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220513073044.ymayac7x7bzatrt7@houat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes, all in drivers.
These patches mosly fix error legs and exceptional conditions
(scsi_dh_alua, qla2xxx). The lpfc fixes are for coding issues with
lpfc features"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Correct BDE DMA address assignment for GEN_REQ_WQE
scsi: lpfc: Fix split code for FLOGI on FCoE
scsi: qla2xxx: Fix missed DMA unmap for aborted commands
scsi: scsi_dh_alua: Properly handle the ALUA transitioning state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Restrict ltq-cputemp to SOC_XWAY to fix build failure
- Add OF device ID table to tmp401 driver to enable auto-load
* tag 'hwmon-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ltq-cputemp) restrict it to SOC_XWAY
hwmon: (tmp401) Add OF device ID table
|
|
Pull drm fixes from Dave Airlie:
"Pretty quiet week on the fixes front, 4 amdgpu and one i915 fix.
I think there might be a few misc fbdev ones outstanding, but I'll see
if they are necessary and pass them on if so.
amdgpu:
- Disable ASPM for VI boards on ADL platforms
- S0ix DCN3.1 display fix
- Resume regression fix
- Stable pstate fix
i915:
- fix for kernel memory corruption when running a lot of OpenCL tests
in parallel"
* tag 'drm-fixes-2022-05-13' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu/ctx: only reset stable pstate if the user changed it (v2)
Revert "drm/amd/pm: keep the BACO feature enabled for suspend"
drm/i915: Fix race in __i915_vma_remove_closed
drm/amd/display: undo clearing of z10 related function pointers
drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems
|
|
With very limited vram on svga3 it's difficult to handle all the surface
migrations. Without gbobjects, i.e. the ability to store surfaces in
guest mobs, there's no reason to support intermediate svga2 features,
especially because we can fall back to fb traces and svga3 will never
support those in-between features.
On svga3 we wither want to use fb traces or screen targets
(i.e. gbobjects), nothing in between. This fixes presentation on a lot
of fusion/esxi tech previews where the exposed svga3 caps haven't been
finalized yet.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 2cd80dbd3551 ("drm/vmwgfx: Add basic support for SVGA3")
Cc: <stable@vger.kernel.org> # v5.14+
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-5-zack@kde.org
|
|
Transition to drm_mode_fb_cmd2 from drm_mode_fb_cmd left the structure
unitialized. drm_mode_fb_cmd2 adds a few additional members, e.g. flags
and modifiers which were never initialized. Garbage in those members
can cause random failures during the bringup of the fbcon.
Initializing the structure fixes random blank screens after bootup due
to flags/modifiers mismatches during the fbcon bring up.
Fixes: dabdcdc9822a ("drm/vmwgfx: Switch to mode_cmd2")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-7-zack@kde.org
|
|
Port of the vmwgfx to SVGAv3 lacked support for fencing. SVGAv3 removed
FIFO's and replaced them with command buffers and extra registers.
The initial version of SVGAv3 lacked support for most advanced features
(e.g. 3D) which made fences unnecessary. That is no longer the case,
especially as 3D support is being turned on.
Switch from FIFO commands and capabilities to command buffers and extra
registers to enable fences on SVGAv3.
Fixes: 2cd80dbd3551 ("drm/vmwgfx: Add basic support for SVGA3")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-5-zack@kde.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Pull interconnect fixes from Georgi:
"interconnect fixes for v5.18-rc
This contains an additional fix for sc7180 and sdx55 platforms that helps
them to enter suspend even on devices that don't have the most recent DT
changes.
- interconnect: Restore sync state by ignoring ipa-virt in provider count
Signed-off-by: Georgi Djakov <djakov@kernel.org>"
* tag 'icc-5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: Restore sync state by ignoring ipa-virt in provider count
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial
Johan writes:
USB-serial fixes for 5.18-rc7
Here are some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM7590
USB: serial: option: add Fibocom MA510 modem
USB: serial: option: add Fibocom L610 modem
USB: serial: pl2303: add device id for HP LM930 Display
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.18-2022-05-11:
amdgpu:
- Disable ASPM for VI boards on ADL platforms
- S0ix DCN3.1 display fix
- Resume regression fix
- Stable pstate fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220511174422.5769-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and bluetooth.
No outstanding fires.
Current release - regressions:
- eth: atlantic: always deep reset on pm op, fix null-deref
Current release - new code bugs:
- rds: use maybe_get_net() when acquiring refcount on TCP sockets
[refinement of a previous fix]
- eth: ocelot: mark traps with a bool instead of guessing type based
on list membership
Previous releases - regressions:
- net: fix skipping features in for_each_netdev_feature()
- phy: micrel: fix null-derefs on suspend/resume and probe
- bcmgenet: check for Wake-on-LAN interrupt probe deferral
Previous releases - always broken:
- ipv4: drop dst in multicast routing path, prevent leaks
- ping: fix address binding wrt vrf
- net: fix wrong network header length when BPF protocol translation
is used on skbs with a fraglist
- bluetooth: fix the creation of hdev->name
- rfkill: uapi: fix RFKILL_IOCTL_MAX_SIZE ioctl request definition
- wifi: iwlwifi: iwl-dbg: use del_timer_sync() before freeing
- wifi: ath11k: reduce the wait time of 11d scan and hw scan while
adding an interface
- mac80211: fix rx reordering with non explicit / psmp ack policy
- mac80211: reset MBSSID parameters upon connection
- nl80211: fix races in nl80211_set_tx_bitrate_mask()
- tls: fix context leak on tls_device_down
- sched: act_pedit: really ensure the skb is writable
- batman-adv: don't skb_split skbuffs with frag_list
- eth: ocelot: fix various issues with TC actions (null-deref; bad
stats; ineffective drops; ineffective filter removal)"
* tag 'net-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
tls: Fix context leak on tls_device_down
net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
net/smc: non blocking recvmsg() return -EAGAIN when no data and signal_pending
net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
mlxsw: Avoid warning during ip6gre device removal
net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral
net: ethernet: mediatek: ppe: fix wrong size passed to memset()
Bluetooth: Fix the creation of hdev->name
i40e: i40e_main: fix a missing check on list iterator
net/sched: act_pedit: really ensure the skb is writable
s390/lcs: fix variable dereferenced before check
s390/ctcm: fix potential memory leak
s390/ctcm: fix variable dereferenced before check
net: atlantic: verify hw_head_ lies within TX buffer ring
net: atlantic: add check for MAX_SKB_FRAGS
net: atlantic: reduce scope of is_rsc_complete
net: atlantic: fix "frag[0] not initialized"
net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()
net: phy: micrel: Fix incorrect variable type in micrel
decnet: Use container_of() for struct dn_neigh casts
...
|
|
In the NIC ->probe() callback, ->mtd_probe() callback is called.
If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too.
In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and
initializes mtd partiion.
But mtd partition for sfc is shared data.
So that allocated mtd partition data from last called
efx_ef10_mtd_probe() will not be used.
Therefore it must be freed.
But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe().
kmemleak reports:
unreferenced object 0xffff88811ddb0000 (size 63168):
comm "systemd-udevd", pid 265, jiffies 4294681048 (age 348.586s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffffa3767749>] kmalloc_order_trace+0x19/0x120
[<ffffffffa3873f0e>] __kmalloc+0x20e/0x250
[<ffffffffc041389f>] efx_ef10_mtd_probe+0x11f/0x270 [sfc]
[<ffffffffc0484c8a>] efx_pci_probe.cold.17+0x3df/0x53d [sfc]
[<ffffffffa414192c>] local_pci_probe+0xdc/0x170
[<ffffffffa4145df5>] pci_device_probe+0x235/0x680
[<ffffffffa443dd52>] really_probe+0x1c2/0x8f0
[<ffffffffa443e72b>] __driver_probe_device+0x2ab/0x460
[<ffffffffa443e92a>] driver_probe_device+0x4a/0x120
[<ffffffffa443f2ae>] __driver_attach+0x16e/0x320
[<ffffffffa4437a90>] bus_for_each_dev+0x110/0x190
[<ffffffffa443b75e>] bus_add_driver+0x39e/0x560
[<ffffffffa4440b1e>] driver_register+0x18e/0x310
[<ffffffffc02e2055>] 0xffffffffc02e2055
[<ffffffffa3001af3>] do_one_initcall+0xc3/0x450
[<ffffffffa33ca574>] do_init_module+0x1b4/0x700
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Fixes: 8127d661e77f ("sfc: Add support for Solarflare SFC9100 family")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220512054709.12513-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Fixes: 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of state->link")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220512021731.2494261-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bandwidth budget table is introduced to trace ideal bandwidth used
by each INT/ISOC endpoint, but in fact the endpoint may consume more
bandwidth and cause data transfer error, so it's better to leave some
margin. Obviously it's difficult to find the best margin for all cases,
instead take use of the worst-case scenario.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220512064931.31670-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to the scheduler allocates the optimal bandwidth for FS ISOC endpoints,
this may be not enough actually and causes data transfer error, so come up
with an estimate that is no less than the worst case bandwidth used for
any one mframe, but may be an over-estimate.
Fixes: 451d3912586a ("usb: xhci-mtk: update fs bus bandwidth by bw_budget_table")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220512064931.31670-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb_gadget_register_driver can be called multi time by to
threads via USB_RAW_IOCTL_RUN ioctl syscall, which will lead
to multiple registrations.
Call trace:
driver_register+0x220/0x3a0 drivers/base/driver.c:171
usb_gadget_register_driver_owner+0xfb/0x1e0
drivers/usb/gadget/udc/core.c:1546
raw_ioctl_run drivers/usb/gadget/legacy/raw_gadget.c:513 [inline]
raw_ioctl+0x1883/0x2730 drivers/usb/gadget/legacy/raw_gadget.c:1220
ioctl USB_RAW_IOCTL_RUN
This routine allows two processes to register the same driver instance
via ioctl syscall. which lead to a race condition.
Please refer to the following scenarios.
T1 T2
------------------------------------------------------------------
usb_gadget_register_driver_owner
driver_register driver_register
driver_find driver_find
bus_add_driver bus_add_driver
priv alloced <context switch>
drv->p = priv;
<schedule out>
kobject_init_and_add // refcount = 1;
//couldn't find an available UDC or it's busy
<context switch>
priv alloced
drv->priv = priv;
kobject_init_and_add
---> refcount = 1 <------
// register success
<context switch>
===================== another ioctl/process ======================
driver_register
driver_find
k = kset_find_obj()
---> refcount = 2 <------
<context out>
driver_unregister
// drv->p become T2's priv
---> refcount = 1 <------
<context switch>
kobject_put(k)
---> refcount = 0 <------
return priv->driver;
--------UAF here----------
There will be UAF in this scenario.
We can fix it by adding a new STATE_DEV_REGISTERING device state to
avoid double register.
Reported-by: syzbot+dc7c3ca638e773db07f6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000e66c2805de55b15a@google.com/
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Schspa Shi <schspa@gmail.com>
Link: https://lore.kernel.org/r/20220508150247.38204-1-schspa@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update MT6360 BMC PHY Tx/Rx setting for the compatibility.
Macpaul reported this CtoDP cable attention message cannot be received from
MT6360 TCPC. But actually, attention message really sent from UFP_D
device.
After RD's comment, there may be BMC PHY Tx/Rx setting causes this issue.
Below's the detailed TCPM log and DP attention message didn't received from 6360
TCPCI.
[ 1206.367775] Identity: 0000:0000.0000
[ 1206.416570] Alternate mode 0: SVID 0xff01, VDO 1: 0x00000405
[ 1206.447378] AMS DFP_TO_UFP_ENTER_MODE start
[ 1206.447383] PD TX, header: 0x1d6f
[ 1206.449393] PD TX complete, status: 0
[ 1206.454110] PD RX, header: 0x184f [1]
[ 1206.456867] Rx VDM cmd 0xff018144 type 1 cmd 4 len 1
[ 1206.456872] AMS DFP_TO_UFP_ENTER_MODE finished
[ 1206.456873] cc:=4
[ 1206.473100] AMS STRUCTURED_VDMS start
[ 1206.473103] PD TX, header: 0x2f6f
[ 1206.475397] PD TX complete, status: 0
[ 1206.480442] PD RX, header: 0x2a4f [1]
[ 1206.483145] Rx VDM cmd 0xff018150 type 1 cmd 16 len 2
[ 1206.483150] AMS STRUCTURED_VDMS finished
[ 1206.483151] cc:=4
[ 1206.505643] AMS STRUCTURED_VDMS start
[ 1206.505646] PD TX, header: 0x216f
[ 1206.507933] PD TX complete, status: 0
[ 1206.512664] PD RX, header: 0x1c4f [1]
[ 1206.515456] Rx VDM cmd 0xff018151 type 1 cmd 17 len 1
[ 1206.515460] AMS STRUCTURED_VDMS finished
[ 1206.515461] cc:=4
Fixes: e1aefcdd394fd ("usb typec: mt6360: Add support for mt6360 Type-C driver")
Cc: stable <stable@vger.kernel.org>
Reported-by: Macpaul Lin <macpaul.lin@mediatek.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/1652159580-30959-1-git-send-email-u0084500@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
IPv6 addresses which are used for tunnels are stored in a hash table
with reference counting. When a new GRE tunnel is configured, the driver
is notified and configures it in hardware.
Currently, any change in the tunnel is not applied in the driver. It
means that if the remote address is changed, the driver is not aware of
this change and the first address will be used.
This behavior results in a warning [1] in scenarios such as the
following:
# ip link add name gre1 type ip6gre local 2000::3 remote 2000::fffe tos inherit ttl inherit
# ip link set name gre1 type ip6gre local 2000::3 remote 2000::ffff ttl inherit
# ip link delete gre1
The change of the address is not applied in the driver. Currently, the
driver uses the remote address which is stored in the 'parms' of the
overlay device. When the tunnel is removed, the new IPv6 address is
used, the driver tries to release it, but as it is not aware of the
change, this address is not configured and it warns about releasing non
existing IPv6 address.
Fix it by using the IPv6 address which is cached in the IPIP entry, this
address is the last one that the driver used, so even in cases such the
above, the first address will be released, without any warning.
[1]:
WARNING: CPU: 1 PID: 2197 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2920 mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum]
...
CPU: 1 PID: 2197 Comm: ip Not tainted 5.17.0-rc8-custom-95062-gc1e5ded51a9a #84
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum]
...
Call Trace:
<TASK>
mlxsw_sp2_ipip_rem_addr_unset_gre6+0xf1/0x120 [mlxsw_spectrum]
mlxsw_sp_netdevice_ipip_ol_event+0xdb/0x640 [mlxsw_spectrum]
mlxsw_sp_netdevice_event+0xc4/0x850 [mlxsw_spectrum]
raw_notifier_call_chain+0x3c/0x50
call_netdevice_notifiers_info+0x2f/0x80
unregister_netdevice_many+0x311/0x6d0
rtnl_dellink+0x136/0x360
rtnetlink_rcv_msg+0x12f/0x380
netlink_rcv_skb+0x49/0xf0
netlink_unicast+0x233/0x340
netlink_sendmsg+0x202/0x440
____sys_sendmsg+0x1f3/0x220
___sys_sendmsg+0x70/0xb0
__sys_sendmsg+0x54/0xa0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: e846efe2737b ("mlxsw: spectrum: Add hash table for IPv6 address mapping")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220511115747.238602-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
drivers/gpu/drm/vc4/vc4_hdmi.c: In function ‘vc4_hdmi_connector_detect’:
drivers/gpu/drm/vc4/vc4_hdmi.c:228:7: error: implicit declaration of function ‘gpiod_get_value_cansleep’; did you mean ‘gpio_get_value_cansleep’? [-Werror=implicit-function-declaration]
if (gpiod_get_value_cansleep(vc4_hdmi->hpd_gpio))
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_get_value_cansleep
CC [M] drivers/gpu/drm/vc4/vc4_validate.o
CC [M] drivers/gpu/drm/vc4/vc4_v3d.o
CC [M] drivers/gpu/drm/vc4/vc4_validate_shaders.o
CC [M] drivers/gpu/drm/vc4/vc4_debugfs.o
drivers/gpu/drm/vc4/vc4_hdmi.c: In function ‘vc4_hdmi_bind’:
drivers/gpu/drm/vc4/vc4_hdmi.c:2883:23: error: implicit declaration of function ‘devm_gpiod_get_optional’; did you mean ‘devm_clk_get_optional’? [-Werror=implicit-function-declaration]
vc4_hdmi->hpd_gpio = devm_gpiod_get_optional(dev, "hpd", GPIOD_IN);
^~~~~~~~~~~~~~~~~~~~~~~
devm_clk_get_optional
drivers/gpu/drm/vc4/vc4_hdmi.c:2883:59: error: ‘GPIOD_IN’ undeclared (first use in this function); did you mean ‘GPIOF_IN’?
vc4_hdmi->hpd_gpio = devm_gpiod_get_optional(dev, "hpd", GPIOD_IN);
^~~~~~~~
GPIOF_IN
drivers/gpu/drm/vc4/vc4_hdmi.c:2883:59: note: each undeclared identifier is reported only once for each function it appears in
cc1: all warnings being treated as errors
Fixes: 6800234ceee0 ("drm/vc4: hdmi: Convert to gpiod")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510135148.247719-1-tanghui20@huawei.com
|
|
The interrupt controller supplying the Wake-on-LAN interrupt line maybe
modular on some platforms (irq-bcm7038-l1.c) and might be probed at a
later time than the GENET driver. We need to specifically check for
-EPROBE_DEFER and propagate that error to ensure that we eventually
fetch the interrupt descriptor.
Fixes: 9deb48b53e7f ("bcmgenet: add WOL IRQ check")
Fixes: 5b1f0e62941b ("net: bcmgenet: Avoid touching non-existent interrupt")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220511031752.2245566-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
'foe_table' is a pointer, the real size of struct mtk_foe_entry
should be pass to memset().
Fixes: ba37b7caf1ed ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220511030829.3308094-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v5.18
Second set of fixes for v5.18 and hopefully the last one. We have a
new iwlwifi maintainer, a fix to rfkill ioctl interface and important
fixes to both stack and two drivers.
* tag 'wireless-2022-05-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
rfkill: uapi: fix RFKILL_IOCTL_MAX_SIZE ioctl request definition
nl80211: fix locking in nl80211_set_tx_bitrate_mask()
mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protection
mac80211_hwsim: fix RCU protected chanctx access
mailmap: update Kalle Valo's email
mac80211: Reset MBSSID parameters upon connection
cfg80211: retrieve S1G operating channel number
nl80211: validate S1G channel width
mac80211: fix rx reordering with non explicit / psmp ack policy
ath11k: reduce the wait time of 11d scan and hw scan while add interface
MAINTAINERS: update iwlwifi driver maintainer
iwlwifi: iwl-dbg: Use del_timer_sync() before freeing
====================
Link: https://lore.kernel.org/r/20220511154535.A1A12C340EE@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bug is here:
ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err);
The list iterator 'ch' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, use a new variable 'iter' as the list iterator,
while use the origin variable 'ch' as a dedicated pointer to
point to the found element.
Cc: stable@vger.kernel.org
Fixes: 1d8d80b4e4ff6 ("i40e: Add macvlan support on i40e")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Requested by Zack for vmwgfx fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Check if the requested stable pstate matches the current one before
changing it. This avoids changing the stable pstate on context
destroy if the user never changed it in the first place via the
IOCTL.
v2: compare the current and requested rather than setting a flag (Lijo)
Fixes: 8cda7a4f96e435 ("drm/amdgpu/UAPI: add new CTX OP to get/set stable pstates")
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This reverts commit eaa090538e8d21801c6d5f94590c3799e6a528b5.
Commit ebc002e3ee78 ("drm/amdgpu: don't use BACO for reset in S3")
stops using BACO for reset during suspend, so it's no longer
necessary to leave BACO enabled during suspend. This fixes
resume from suspend on the navy flounder dGPU in the ASUS ROG
Strix G513QY.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2008
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1982
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
smatch complains about
drivers/s390/net/lcs.c:1741 lcs_get_control() warn: variable dereferenced before check 'card->dev' (see line 1739)
Fixes: 27eb5ac8f015 ("[PATCH] s390: lcs driver bug fixes and improvements [1/2]")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smatch complains about
drivers/s390/net/ctcm_mpc.c:1210 ctcmpc_unpack_skb() warn: possible memory leak of 'mpcginfo'
mpc_action_discontact() did not free mpcginfo. Consolidate the freeing in
ctcmpc_unpack_skb().
Fixes: 293d984f0e36 ("ctcm: infrastructure for replaced ctc driver")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Found by cppcheck and smatch.
smatch complains about
drivers/s390/net/ctcm_sysfs.c:43 ctcm_buffer_write() warn: variable dereferenced before check 'priv' (see line 42)
Fixes: 3c09e2647b5e ("ctcm: rename READ/WRITE defines to avoid redefinitions")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bounds check hw_head index provided by NIC to verify it lies
within the TX buffer ring.
Reported-by: Aashay Shringarpure <aashay@google.com>
Reported-by: Yi Chou <yich@google.com>
Reported-by: Shervin Oloumi <enlightened@google.com>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enforce that the CPU can not get stuck in an infinite loop.
Reported-by: Aashay Shringarpure <aashay@google.com>
Reported-by: Yi Chou <yich@google.com>
Reported-by: Shervin Oloumi <enlightened@google.com>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't defer handling the err case outside the loop. That's pointless.
And since is_rsc_complete is only used inside this loop, declare
it inside the loop to reduce it's scope.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In aq_ring_rx_clean(), if buff->is_eop is not set AND
buff->len < AQ_CFG_RX_HDR_SIZE, then hdr_len remains equal to
buff->len and skb_add_rx_frag(xxx, *0*, ...) is not called.
The loop following this code starts calling skb_add_rx_frag() starting
with i=1 and thus frag[0] is never initialized. Since i is initialized
to zero at the top of the primary loop, we can just reference and
post-increment i instead of hardcoding the 0 when calling
skb_add_rx_frag() the first time.
Reported-by: Aashay Shringarpure <aashay@google.com>
Reported-by: Yi Chou <yich@google.com>
Reported-by: Shervin Oloumi <enlightened@google.com>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to using pcim_enable_device() to avoid missing pci_disable_device().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220510031316.1780409-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Garbage FCoE CT frames are transmitted on the wire because of bad DMA ptr
addresses filled in the GEN_REQ_WQE.
The __lpfc_sli_prep_gen_req_s4() routine is using the wrong buffer for the
payload address. Change the DMA buffer assignment from the bmp buffer to
the bpl buffer.
Link: https://lore.kernel.org/r/20220506205548.61644-1-jsmart2021@gmail.com
Fixes: 61910d6a5243 ("scsi: lpfc: SLI path split: Refactor CT paths")
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The refactoring code converted context information from SLI-3 to SLI-4.
The conversion for the SLI-4 bit field tried to use the old (hacky) SLI3
high/low bit settings. Needless to say, it was incorrect.
Explicitly set the context field to type FCFI and set it in the wqe.
SLI-4 is now a proper bit field so no need for the shifting/anding.
Link: https://lore.kernel.org/r/20220506205528.61590-1-jsmart2021@gmail.com
Fixes: 6831ce129f19 ("scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path")
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In lanphy_read_page_reg, calling __phy_read() might return a negative
error code. Use 'int' to check the error code.
Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220509144519.2343399-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When dma_buf_stats_setup() fails, it closes the dmabuf file which
results into the calling of dma_buf_file_release() where it does
list_del(&dmabuf->list_node) with out first adding it to the proper
list. This is resulting into panic in the below path:
__list_del_entry_valid+0x38/0xac
dma_buf_file_release+0x74/0x158
__fput+0xf4/0x428
____fput+0x14/0x24
task_work_run+0x178/0x24c
do_notify_resume+0x194/0x264
work_pending+0xc/0x5f0
Fix it by moving the dma_buf_stats_setup() after dmabuf is added to the
list.
Fixes: bdb8d06dfefd ("dmabuf: Add the capability to expose DMA-BUF stats in sysfs")
Signed-off-by: Charan Teja Reddy <quic_charante@quicinc.com>
Tested-by: T.J. Mercier <tjmercier@google.com>
Acked-by: T.J. Mercier <tjmercier@google.com>
Cc: <stable@vger.kernel.org> # 5.15.x+
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1652125797-2043-1-git-send-email-quic_charante@quicinc.com
|
|
The impact of this regression is the same for resume that I saw on
thaw: the kernel hangs and nothing except SysRq rebooting can be done.
Fixes regression in commit cbe6c3a8f8f4 ("net: atlantic: invert deep
par in pm functions, preventing null derefs"), where I disabled deep
pm resets in suspend and resume, trying to make sense of the
atl_resume_common() deep parameter in the first place.
It turns out, that atlantic always has to deep reset on pm
operations. Even though I expected that and tested resume, I screwed
up by kexec-rebooting into an unpatched kernel, thus missing the
breakage.
This fixup obsoletes the deep parameter of atl_resume_common, but I
leave the cleanup for the maintainers to post to mainline.
Suspend and hibernation were successfully tested by the reporters.
Fixes: cbe6c3a8f8f4 ("net: atlantic: invert deep par in pm functions, preventing null derefs")
Link: https://lore.kernel.org/regressions/9-Ehc_xXSwdXcvZqKD5aSqsqeNj5Izco4MYEwnx5cySXVEc9-x_WC4C3kAoCqNTi-H38frroUK17iobNVnkLtW36V6VWGSQEOHXhmVMm5iQ=@protonmail.com/
Reported-by: Jordan Leppert <jordanleppert@protonmail.com>
Reported-by: Holger Hoffstaette <holger@applied-asynchrony.com>
Tested-by: Jordan Leppert <jordanleppert@protonmail.com>
Tested-by: Holger Hoffstaette <holger@applied-asynchrony.com>
CC: <stable@vger.kernel.org> # 5.10+
Signed-off-by: Manuel Ullmann <labre@posteo.de>
Link: https://lore.kernel.org/r/87bkw8dfmp.fsf@posteo.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-05-06
This series contains updates to ice driver only.
Ivan Vecera fixes a race with aux plug/unplug by delaying setting adev
until initialization is complete and adding locking.
Anatolii ensures VF queues are completely disabled before attempting to
reconfigure them.
Michal ensures stale Tx timestamps are cleared from hardware.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix PTP stale Tx timestamps cleanup
ice: clear stale Tx queue settings before configuring
ice: Fix race during aux device (un)plugging
====================
Link: https://lore.kernel.org/r/20220506174129.4976-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000 00000000 00000000 00000000
[ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Thread 1 (phylib WQ) | Thread 2 (phy interrupt)
|
| phy_interrupt() <-- PHY IRQ
| handle_interrupt()
| phy_read()
| phy_trigger_machine()
| --> schedule phylib WQ
|
|
phy_state_machine() |
phy_check_link_status() |
phy_link_change() |
phydev->adjust_link() |
fec_enet_adjust_link() |
--> FEC reset | phy_interrupt() <-- PHY IRQ
| phy_read()
|
Fix this by acquiring the phydev lock in phy_interrupt().
Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/
Fixes: c974bdbc3e77 ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices")
cc: <stable@vger.kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Building with SENSORS_LTQ_CPUTEMP=y with SOC_FALCON=y causes build
errors since FALCON does not support the same features as XWAY.
Change this symbol to depend on SOC_XWAY since that provides the
necessary interfaces.
Repairs these build errors:
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_enable':
../drivers/hwmon/ltq-cputemp.c:23:9: error: implicit declaration of function 'ltq_cgu_w32'; did you mean 'ltq_ebu_w32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c:23:21: error: implicit declaration of function 'ltq_cgu_r32'; did you mean 'ltq_ebu_r32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_probe':
../drivers/hwmon/ltq-cputemp.c:92:31: error: 'SOC_TYPE_VR9_2' undeclared (first use in this function)
92 | if (ltq_soc_type() != SOC_TYPE_VR9_2)
Fixes: 7074d0a92758 ("hwmon: (ltq-cputemp) add cpu temp sensor driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20220509234740.26841-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The initial code used roundup() to round the starting time to
a multiple of a period. This generated an error on 32-bit
systems, so was replaced with DIV_ROUND_UP_ULL().
However, this truncates to 32-bits on a 64-bit system. Replace
with DIV64_U64_ROUND_UP() instead.
Fixes: b325af3cfab9 ("ptp: ocp: Add signal generators and update sysfs nodes")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220506223739.1930-2-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the missing pci_disable_device() before return
from tulip_init_one() in the error handling case.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220506094250.3630615-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If ionic_map_bars() fails, pci_release_regions() need be called.
Fixes: fbfb8031533c ("ionic: Add hardware init and device commands")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220506034040.2614129-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
