| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The mvneta driver advertises it supports IFF_UNICAST_FLT. However, it
actually does not. The hardware probably does support it, but there is
no code to configure the filter. As a quick and simple fix, remove the
flag. This will cause the core to fall back to promiscuous mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: b50b72de2f2f ("net: mvneta: enable features before registering the driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop duplicate headers types.h and delay.h from dwc_eth_qos.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f9c ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When busy polling while a link is down (during a link-flap test), TX
timeouts were observed as well as the following messages in the ring
buffer:
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free tx failed. rc:-1
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free rx failed. rc:-1
These were resolved by checking for link status and returning if link
was not up.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Rob Miller <rob.miller@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure mlx4_en_free_resources is called under the netdev state lock.
This is needed since RCU dereference of XDP prog should be protected.
Fixes: 326fe02d1ed6 ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Sagi Grimberg <sagi@grimberg.me>
CC: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Knowing that:
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN (0x1UL << 0)
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE (0x5UL << 0)
and that 'bnxt_hwrm_tunnel_dst_port_alloc()' is only called with one of
these 2 constants, the TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE can not
trigger.
Replace the bit test that overlap by an equality test, just as in
'bnxt_hwrm_tunnel_dst_port_free()' above.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When dev_set_promiscuity failed in macvlan_open, it always invokes
dev_set_allmulti without checking if necessary.
Now check the IFF_ALLMULTI flag firstly before rollback the multicast
setting in the error handler.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix setting of SUPPORTED_FIBRE bit as it was not present in features
of KSZ8041.
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull sparc fixes from David Miller:
1) With modern networking cards we can run out of 32-bit DMA space, so
support 64-bit DMA addressing when possible on sparc64. From Dave
Tushar.
2) Some signal frame validation checks are inverted on sparc32, fix
from Andreas Larsson.
3) Lockdep tables can get too large in some circumstances on sparc64,
add a way to adjust the size a bit. From Babu Moger.
4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: drop duplicate header scatterlist.h
lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
sunbmac: Fix compiler warning
sunqe: Fix compiler warnings
sparc64: Enable 64-bit DMA
sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
sparc64: Bind PCIe devices to use IOMMU v2 service
sparc64: Initialize iommu_map_table and iommu_pool
sparc64: Add ATU (new IOMMU) support
sparc64: Add FORCE_MAX_ZONEORDER and default to 13
sparc64: fix compile warning section mismatch in find_node()
sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
sparc64: Fix find_node warning if numa node cannot be found
|
|
Pull networking fixes from David Miller:
1) Clear congestion control state when changing algorithms on an
existing socket, from Florian Westphal.
2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
from Jia Jie Ho.
3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
CAVALLARO.
4) Fix udplite multicast delivery handling, it ignores the udp_table
parameter passed into the lookups, from Pablo Neira Ayuso.
5) Synchronize the space estimated by rtnl_vfinfo_size and the space
actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.
6) Fix memory leak in fib_info when splitting nodes, from Alexander
Duyck.
7) If a driver does a napi_hash_del() explicitily and not via
netif_napi_del(), it must perform RCU synchronization as needed. Fix
this in virtio-net and bnxt drivers, from Eric Dumazet.
8) Likewise, it is not necessary to invoke napi_hash_del() is we are
also doing neif_napi_del() in the same code path. Remove such calls
from be2net and cxgb4 drivers, also from Eric Dumazet.
9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
from WANG Cong.
10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.
11) We cannot cache routes in ip6_tunnel when using inherited traffic
classes, from Paolo Abeni.
12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.
13) Splice operations cannot use freezable blocking calls in AF_UNIX,
from WANG Cong.
14) Link dump filtering by master device and kind support added an error
in loop index updates during the dump if we actually do filter, fix
from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: zero ca_priv area when switching cc algorithms
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
tipc: eliminate obsolete socket locking policy description
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
net: macb: add check for dma mapping error in start_xmit()
rtnetlink: fix FDB size computation
netns: fix get_net_ns_by_fd(int pid) typo
af_unix: conditionally use freezable blocking calls in read
net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
net: ethernet: ti: cpsw: add missing sanity check
net: ethernet: ti: cpsw: fix secondary-emac probe error path
net: ethernet: ti: cpsw: fix of_node and phydev leaks
net: ethernet: ti: cpsw: fix deferred probe
net: ethernet: ti: cpsw: fix mdio device reference leak
net: ethernet: ti: cpsw: fix bad register access in probe error path
net: sky2: Fix shutdown crash
cfg80211: limit scan results cache size
net sched filters: pass netlink message flags in event notification
...
|
|
There's not much point, except compile test, enabling the stmmac
platform drivers unless the STM32 SoC is enabled. It's not
useful without it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again a set of smaller fixes across several platforms (OMAP, Marvell,
Allwinner, i.MX, etc).
A handful of typo fixes and smaller missing contents from device
trees, with some tweaks to OMAP mach files to deal with CPU feature
print misformatting, potential NULL ptr dereference and one setup
issue with UARTs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
ARM: dts: STiH410-b2260: Fix typo in spi0 chipselect definition
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
arm64: dts: marvell: add unique identifiers for Armada A8k SPI controllers
arm64: dts: marvell: fix clocksource for CP110 slave SPI0
arm64: dts: marvell: Fix typo in label name on Armada 37xx
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
ARM: dts: imx53-qsb: Fix regulator constraints
ARM: dts: sun8i: fix the pinmux for UART1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some I2C driver bugfixes (and one documentation fix)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-mux-pca954x: fix deselect enabling for device-tree
i2c: digicolor: use clk_disable_unprepare instead of clk_unprepare
i2c: mux: fix up dependencies
i2c: Documentation: i2c-topology: fix minor whitespace nit
i2c: mux: demux-pinctrl: make drivers with no pinctrl work again
|
|
Deselect functionality can be ignored for device-trees with
"i2c-mux-idle-disconnect" entries if no platform_data is available.
By enabling the deselect functionality outside the platform_data
block the logic works as it did in previous kernels.
Fixes: 7fcac9807175 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Ziyang Wu <ziywu@cisco.com>
[touched up a few minor issues /peda]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Compiler warning in caam driver that was the last one remaining
- Do not register aes-xts in caam drivers on unsupported platforms
- Regression in algif_hash interface that may lead to an oops"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_hash - Fix NULL hash crash with shash
crypto: caam - fix type mismatch warning
crypto: caam - do not register AES-XTS mode on LP units
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Some driver fixes which we pending in my tree:
- return error code fix in edma driver
- Kconfig fix for genric allocator in mmp_tdma
- fix uninitialized value in sun6i
- Runtime pm fixes for cppi"
* tag 'dmaengine-fix-4.9-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: cppi41: More PM runtime fixes
dmaengine: cpp41: Fix handling of error path
dmaengine: cppi41: Fix unpaired pm runtime when only a USB hub is connected
dmaengine: cppi41: Fix list not empty warning on module removal
dmaengine: sun6i: fix the uninitialized value for v_lli
dmaengine: mmp_tdma: add missing select GENERIC_ALLOCATOR in Kconfig
dmaengine: edma: Fix error return code in edma_alloc_chan_resources()
|
|
at91ether_start_xmit() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"They fix an ACPI thermal management regression introduced by a recent
FADT handling cleanup, an ACPI tools build issue introduced by a
recent ACPICA commit and a PCC mailbox initialization bug causing
lockdep to complain loudly.
Specifics:
- Revert a recent ACPICA cleanup that attempted to get rid of all
FADT version 2 legacy, but broke ACPI thermal management on at
least one system (Rafael Wysocki).
- Fix cross-compiled builds of ACPI tools that stopped working after
a recent cleanup related to the handling of header files in ACPICA
(Lv Zheng).
- Fix a locking issue in the PCC channel initialization code that
invokes devm_request_irq() under a spinlock (among other things)
and causes lockdep to complain (Hoan Tran)"
* tag 'acpi-4.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power/acpi: Remove direct kernel source include reference
mailbox: PCC: Fix lockdep warning when request PCC channel
Revert "ACPICA: FADT support cleanup"
|
|
* acpica-fixes:
Revert "ACPICA: FADT support cleanup"
* acpi-cppc-fixes:
mailbox: PCC: Fix lockdep warning when request PCC channel
* acpi-tools-fixes:
tools/power/acpi: Remove direct kernel source include reference
|
|
sunbmac uses '__u32' for dma handle while invoking kernel DMA APIs,
instead of using dma_addr_t. This hasn't caused any 'incompatible
pointer type' warning on SPARC because until now dma_addr_t is of
type u32. However, recent changes in SPARC ATU (iommu) enables 64bit
DMA and therefore dma_addr_t becomes of type u64. This makes
'incompatible pointer type' warnings inevitable.
e.g.
drivers/net/ethernet/sun/sunbmac.c: In function ‘bigmac_ether_init’:
drivers/net/ethernet/sun/sunbmac.c:1166: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
This patch resolves above compiler warning.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sunqe uses '__u32' for dma handle while invoking kernel DMA APIs,
instead of using dma_addr_t. This hasn't caused any 'incompatible
pointer type' warning on SPARC because until now dma_addr_t is of
type u32. However, recent changes in SPARC ATU (iommu) enables 64bit
DMA and therefore dma_addr_t becomes of type u64. This makes
'incompatible pointer type' warnings inevitable.
e.g.
drivers/net/ethernet/sun/sunqe.c: In function ‘qec_ether_init’:
drivers/net/ethernet/sun/sunqe.c:883: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
drivers/net/ethernet/sun/sunqe.c:885: warning: passing argument 3 of ‘dma_alloc_coherent’ from incompatible pointer type
./include/linux/dma-mapping.h:445: note: expected ‘dma_addr_t *’ but argument is of type ‘__u32 *’
This patch resolves above compiler warnings.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more bugfixes:
* limit # of scan results stored in memory - this is a long-standing bug
Jouni and I only noticed while discussing other things in Santa Fe
* revert AP_LINK_PS patch that was causing issues (Felix)
* various A-MSDU/A-MPDU fixes for TXQ code (Felix)
* interoperability workaround for peers with broken VHT capabilities
(Filip Matusiak)
* add bitrate definition for a VHT MCS that's supposed to be invalid
but gets used by some hardware anyway (Thomas Pedersen)
* beacon timer fix in hwsim (Benjamin Beichler)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to propagate errors from of_phy_register_fixed_link() which
can fail with -EPROBE_DEFER.
Fixes: 1f71e8c96fc6 ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to check for allocation failures before dereferencing a
NULL-pointer during probe.
Fixes: 649a1688c960 ("net: ethernet: ti: cpsw: create common struct to
hold shared driver data")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister the primary device in case the secondary emac
fails to probe.
kernel BUG at /home/johan/work/omicron/src/linux/net/core/dev.c:7743!
...
[<c05b3dec>] (free_netdev) from [<c04fe6c0>] (cpsw_probe+0x9cc/0xe50)
[<c04fe6c0>] (cpsw_probe) from [<c047b28c>] (platform_drv_probe+0x5c/0xc0)
Fixes: d9ba8f9e6298 ("driver: net: ethernet: cpsw: dual emac interface
implementation")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop references taken and deregister devices registered
during probe on probe errors (including deferred probe) and driver
unbind.
Specifically, PHY of-node references were never released and fixed-link
PHY devices were never deregistered.
Fixes: 9e42f715264f ("drivers: net: cpsw: add phy-handle parsing")
Fixes: 1f71e8c96fc6 ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister all child devices also on probe errors to avoid
leaks and to fix probe deferral:
cpsw 4a100000.ethernet: omap_device: omap_device_enable() called from invalid state 1
cpsw 4a100000.ethernet: use pm_runtime_put_sync_suspend() in driver?
cpsw: probe of 4a100000.ethernet failed with error -22
Add generic helper to undo the effects of cpsw_probe_dt(), which will
also be used in a follow-on patch to fix further leaks that have been
introduced more recently.
Note that the platform device is now runtime-resumed before registering
any child devices in order to make sure that it is synchronously
suspended after having deregistered the children in the error path.
Fixes: 1fb19aa730e4 ("net: cpsw: Add parent<->child relation support
between cpsw and mdio")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by of_find_device_by_node() when
looking up an mdio device from a phy_id property during probe.
Fixes: 549985ee9c72 ("cpsw: simplify the setup of the register
pointers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to keep the platform device runtime-resumed throughout probe
to avoid accessing the CPSW registers in the error path (e.g. for
deferred probe) with clocks disabled:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0872d08
...
[<c04fabcc>] (cpsw_ale_control_set) from [<c04fb8b4>] (cpsw_ale_destroy+0x2c/0x44)
[<c04fb8b4>] (cpsw_ale_destroy) from [<c04fea58>] (cpsw_probe+0xbd0/0x10c4)
[<c04fea58>] (cpsw_probe) from [<c047b2a0>] (platform_drv_probe+0x5c/0xc0)
Fixes: df828598a755 ("netdev: driver: ethernet: Add TI CPSW driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sky2 frequently crashes during machine shutdown with:
sky2_get_stats+0x60/0x3d8 [sky2]
dev_get_stats+0x68/0xd8
rtnl_fill_stats+0x54/0x140
rtnl_fill_ifinfo+0x46c/0xc68
rtmsg_ifinfo_build_skb+0x7c/0xf0
rtmsg_ifinfo.part.22+0x3c/0x70
rtmsg_ifinfo+0x50/0x5c
netdev_state_change+0x4c/0x58
linkwatch_do_dev+0x50/0x88
__linkwatch_run_queue+0x104/0x1a4
linkwatch_event+0x30/0x3c
process_one_work+0x140/0x3e0
worker_thread+0x60/0x44c
kthread+0xdc/0xf0
ret_from_fork+0x10/0x50
This is caused by the sky2 being called after it has been shutdown.
A previous thread about this can be found here:
https://lkml.org/lkml/2016/4/12/410
An alternative fix is to assure that IFF_UP gets cleared by
calling dev_close() during shutdown. This is similar to what the
bnx2/tg3/xgene and maybe others are doing to assure that the driver
isn't being called following _shutdown().
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"These are hopefully the last GPIO fixes for v4.9. The most important
is that it fixes the UML randconfig builds that have been nagging me
for some time and me being confused about where the problem was really
sitting, now this fix give this nice feeling that everything is solid
and builds fine.
Summary:
- Finally, after being puzzled by a bunch of recurrent UML build
failures on randconfigs from the build robot, Keno Fischer nailed
it: GPIO_DEVRES is optional and depends on HAS_IOMEM even though
many users just unconditionally rely on it to be available. And it
*should* be available: garbage collection is nice for this and it
*certainly* has nothing to do with having IOMEM. So we got rid of
it, and now the UML builds should JustWork(TM).
- Do not call .get_direction() on sleeping GPIO chips on the fastpath
when locking GPIOs for interrupts: it is done from atomic context,
no way.
- Some driver fixes"
* tag 'gpio-v4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Remove GPIO_DEVRES option
gpio: tc3589x: fix up .get_direction()
gpio: do not double-check direction on sleeping chips
gpio: pca953x: Move memcpy into mutex lock for set multiple
gpio: pca953x: Fix corruption of other gpios in set_multiple.
|
|
since clk_prepare_enable() is used to get i2c->clk, we should
use clk_disable_unprepare() to release it for the error path.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
ssh://git.freedesktop.org/git/drm-intel into drm-fixes
i915 misc fixes.
* tag 'drm-intel-fixes-2016-11-17' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915: Assume non-DP++ port if dvo_port is HDMI and there's no AUX ch specified in the VBT
drm/i915: Refresh that status of MST capable connectors in ->detect()
drm/i915: Grab the rotation from the passed plane state for VLV sprites
drm/i915: Mark CPU cache as dirty when used for rendering
|
|
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit f752fff611b99f5679224f3990a1f531ea64b1ec.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit 83ba62bc700bab710b22be3a1bf6cf973f754273.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Pull block fixes from Jens Axboe:
"A set of fixes, one for NVMe from Keith, and a set for nvme-{rdma,t,f}
from the usual suspects, fixing actual problems that would be a shame
to release 4.9 with"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme/pci: Don't free queues on error
nvmet-rdma: drain the queue-pair just before freeing it
nvme-rdma: stop and free io queues on connect failure
nvmet-rdma: don't forget to delete a queue from the list of connection failed
nvmet: Don't queue fatal error work if csts.cfs is set
nvme-rdma: reject non-connect commands before the queue is live
nvmet-rdma: Fix possible NULL deref when handling rdma cm events
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rmda fixes from Doug Ledford.
"First round of -rc fixes.
Due to various issues, I've been away and couldn't send a pull request
for about three weeks. There were a number of -rc patches that built
up in the meantime (some where there already from the early -rc
stages). Obviously, there were way too many to send now, so I tried to
pare the list down to the more important patches for the -rc cycle.
Most of the code has had plenty of soak time at the various vendor's
testing setups, so I doubt there will be another -rc pull request this
cycle. I also tried to limit the patches to those with smaller
footprints, so even though a shortlog is longer than I would like, the
actual diffstat is mostly very small with the exception of just three
files that had more changes, and a couple files with pure removals.
Summary:
- Misc Intel hfi1 fixes
- Misc Mellanox mlx4, mlx5, and rxe fixes
- A couple cxgb4 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (34 commits)
iw_cxgb4: invalidate the mr when posting a read_w_inv wr
iw_cxgb4: set *bad_wr for post_send/post_recv errors
IB/rxe: Update qp state for user query
IB/rxe: Clear queue buffer when modifying QP to reset
IB/rxe: Fix handling of erroneous WR
IB/rxe: Fix kernel panic in UDP tunnel with GRO and RX checksum
IB/mlx4: Fix create CQ error flow
IB/mlx4: Check gid_index return value
IB/mlx5: Fix NULL pointer dereference on debug print
IB/mlx5: Fix fatal error dispatching
IB/mlx5: Resolve soft lock on massive reg MRs
IB/mlx5: Use cache line size to select CQE stride
IB/mlx5: Validate requested RQT size
IB/mlx5: Fix memory leak in query device
IB/core: Avoid unsigned int overflow in sg_alloc_table
IB/core: Add missing check for addr_resolve callback return value
IB/core: Set routable RoCE gid type for ipv4/ipv6 networks
IB/cm: Mark stale CM id's whenever the mad agent was unregistered
IB/uverbs: Fix leak of XRC target QPs
IB/hfi1: Remove incorrect IS_ERR check
...
|
|
Make sure to drop the of_node reference taken in fixed_phy_register()
when deregistering a PHY.
Fixes: a75951217472 ("net: phy: extend fixed driver with
fixed_phy_register()")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by bus_find_device() before
returning NULL from of_phy_find_device() when the found device is not a
PHY.
Fixes: 6ed742363b9c ("of: of_mdio: Ensure mdio device is a PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the of_node reference also on failure to parse the
speed property in of_phy_register_fixed_link().
Fixes: 3be2a49e5c08 ("of: provide a binding for fixed link PHYs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building the caam driver on arm64 produces a harmless warning:
drivers/crypto/caam/caamalg.c:140:139: warning: comparison of distinct pointer types lacks a cast
We can use min_t to tell the compiler which type we want it to use
here.
Fixes: 5ecf8ef9103c ("crypto: caam - fix sg dump")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix use of u32 instead of int for checking for negative errors values
as pointed out by Dan Carpenter <dan.carpenter@oracle.com>.
And while testing the PM runtime error path by randomly returning
failed values in runtime resume, I noticed two more places that need
fixing:
- If pm_runtime_get_sync() fails in probe, we still need to do
pm_runtime_put_sync() to keep the use count happy. We could call
pm_runtime_put_noidle() on the error path, but we're just going
to call pm_runtime_disable() after that so pm_runtime_put_sync()
will do what we want
- We should print an error if pm_runtime_get_sync() fails in
cppi41_dma_alloc_chan_resources() so we know where it happens
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 740b4be3f742 ("dmaengine: cpp41: Fix handling of error path")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add a missing synchronize_net() call to avoid potential use after free,
since we explicitly call napi_hash_del() to factorize the RCU grace
period.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently have a fundamental problem in how we treat the CPU port and
its VLAN membership. As soon as a second VLAN is configured to be
untagged, the CPU automatically becomes untagged for that VLAN as well,
and yet, we don't gracefully make sure that the CPU becomes tagged in
the other VLANs it could be a member of. This results in only one VLAN
being effectively usable from the CPU's perspective.
Instead of having some pretty complex logic which tries to maintain the
CPU port's default VLAN and its untagged properties, just do something
very simple which consists in neither altering the CPU port's PVID
settings, nor its untagged settings:
- whenever a VLAN is added, the CPU is automatically a member of this
VLAN group, as a tagged member
- PVID settings for downstream ports do not alter the CPU port's PVID
since it now is part of all VLANs in the system
This means that a typical example where e.g: LAN ports are in VLAN1, and
WAN port is in VLAN2, now require having two VLAN interfaces for the
host to properly terminate and send traffic from/to.
Fixes: Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes fr9om Dave Airlie:
"Fixes for amdgpu, and a bunch of arm drivers.
There seems to be an uptick in the ARM drivers sending things for
fixes which is good, so I've decided to dequeue a bit early, more
stuff may arrive before the weekend.
This contains mediatek, arcpgu, sunxi, fsl-dcu display controller
fixes along with 3 amdgpu fixes, one for a fencing issue with
secondary GPUs"
* tag 'drm-fixes-for-v4.9-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu:fix vpost_needed routine
drm/amdgpu/powerplay: drop a redundant NULL check
drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)
drm/arcpgu: Accommodate adv7511 switch to DRM bridge
drm/fsl-dcu: disable planes before disabling CRTC
drm/fsl-dcu: update all registers on flush
drm/fsl-dcu: do not update when modifying irq registers
drm/sun4i: Propagate error to the caller
drm/sun4i: Fix error handling
drm/mediatek: modify the factor to make the pll_rate set in the 1G-2G range
drm/mediatek: enhance the HDMI driving current
drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable
drm/mediatek: clear IRQ status before enable OVL interrupt
drm/mediatek: set vblank_disable_allowed to true
drm/mediatek: fix a typo of OD_CFG to OD_RELAYMODE
drm/sun4i: rgb: Remove the bridge enable/disable functions
drm/sun4i: rgb: Enable panel after controller
|
|
Also, rearrange things a bit to have a common c4iw_invalidate_mr()
function used everywhere that we need to invalidate.
Fixes: 49b53a93a64a ("iw_cxgb4: add fast-path for small REG_MR operations")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There are a few cases in c4iw_post_send() and c4iw_post_receive()
where *bad_wr is not set when an error is returned. This can
cause a crash if the application tries to use bad_wr.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
|
|
The method rxe_qp_error() transitions QP to error state
and make sure the QP is drained. It did not though update
the QP state for user's query.
This patch fixes this.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
