| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The watchdog maximum timeout value is determined by the number of bits
for the interval timer counter, its source clock frequency, the number
of bits of the prescaler and maximum divider value.
This can be calculated with the following equation:
max_timeout = counter / (freq / (max_prescale + 1) / max_divider)
Setting a maximum timeout value will allow the watchdog core to refuse
user-space calls to the WDIOC_SETTIMEOUT ioctl that sets not supported
timeout values.
For example, systemd tries to set a timeout of 10 minutes on reboot to
ensure that the machine will be rebooted even if a reboot failed. This
leads to the following error message on an Exynos5422 Odroid XU4 board:
[ 147.986045] s3c2410-wdt 101d0000.watchdog: timeout 600 too big
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal (WS0)
is for alerting the system by interrupt, the second one (WS1) is a real
hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage watchdog
or a two stages watchdog, it's set up by the module parameter "action".
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
In the two stages mode, when the timeout is reached, the first signal (WS0)
will trigger panic. If the system is getting into trouble and cannot be reset
by panic or restart properly by the kdump kernel(if supported), then the
second stage (as long as the first stage) will be reached, system will be
reset by WS1. This function can help administrator to backup the system
context info by panic console output or kdump.
This driver bases on linux kernel watchdog framework, so it can get
timeout from module parameter and FDT at the driver init stage.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Tested-by: Pratyush Anand <panand@redhat.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The WinSystems EBC-C384 has an onboard watchdog timer. The timeout range
supported by the watchdog timer is 1 second to 255 minutes. Timeouts
under 256 seconds have a 1 second granularity, while the rest have a 1
minute granularity.
This driver adds watchdog timer support for this onboard watchdog timer.
The timeout may be configured via the timeout module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add support for the watchdog timer on NI cRIO-903x and cDAQ-913x real-
time controllers.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The 'action' (or restart mode) and data parameters may be used by restart
handlers, so they should be passed to the restart callback functions.
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The Zodiac watchdog is implemented on a microcontoller. The reset reason
currently labelled "trigger" is not to detect when the watchdog has
triggered (as had been initially understood and suggested by the naming),
but to inform the reader that the watchdog, which in fact has it's own
hardware watchdog, has been reset because the hardware watchdog has
triggered. Renaming to "hw watchdog".
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Calling return copy_to_user(...) in an ioctl will not do the right thing
if there's a pagefault: copy_to_user returns the number of bytes not
copied in this case.
Fix up watchdog/rc32434_wdt to do
return copy_to_user(...)) ? -EFAULT : 0;
instead.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The BCM7038 watchdog driver is specific to Broadcom ARM and MIPS
SoCs so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The driver uses the atomic_io_modify() function to update registers, but
that function is only available on 32-bit ARM. Recent changes have added
ARCH_MVEBU support to 64-bit ARM and hence allowed this driver to build
on 64-bit ARM where this function isn't available and thereby causing
allmodconfig builds to break.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The Technologic Systems TS-4800 is an i.MX515 board, so its drivers
are useless unless building a SOC_IMX51 kernel, except for build
testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
As used in (and tested on) the ASRock IMB-150 board. Implementation is
identical to other NCT chips, just with different registers.
Signed-off-by: Rob Kramer <rob@solution-space.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Four small fixes for irqchip drivers:
- Add missing low level irq handler initialization on mxs, so
interrupts can acutally be delivered
- Add a missing barrier to the GIC driver
- Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
and a cache flush beyond the actual region"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
irqchip/mxs: Add missing set_handle_irq()
irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/android fix from Greg KH:
"Here is one patch, for the android binder driver, to resolve a
reported problem. Turns out it has been around for a while (since
3.15), so it is good to finally get it resolved.
It has been in linux-next for a while with no reported issues"
* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few USB fixes for 4.5-rc6
They fix a reported bug for some USB 3 devices by reverting the recent
patch, a MAINTAINERS change for some drivers, some new device ids, and
of course, the usual bunch of USB gadget driver fixes.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
MAINTAINERS: drop OMAP USB and MUSB maintainership
usb: musb: fix DMA for host mode
usb: phy: msm: Trigger USB state detection work in DRD mode
usb: gadget: net2280: fix endpoint max packet for super speed connections
usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
usb: gadget: remove driver from pending list on probe error
Revert "usb: hub: do not clear BOS field during reset device"
usb: chipidea: fix return value check in ci_hdrc_pci_probe()
usb: chipidea: error on overflow for port_test_write
USB: option: add "4G LTE usb-modem U901"
USB: cp210x: add IDs for GE B650V3 and B850V3 boards
USB: option: add support for SIM7100E
usb: musb: Fix DMA desired mode for Mentor DMA engine
usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
usb: dwc2: USB_DWC2 should depend on HAS_DMA
usb: dwc2: host: fix the data toggle error in full speed descriptor dma
usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
usb: dwc3: Fix assignment of EP transfer resources
usb: dwc2: Add extra delay when forcing dr_mode
|
|
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dax: move writeback calls into the filesystems
dax: give DAX clearing code correct bdev
ext4: online defrag not supported with DAX
ext2, ext4: only set S_DAX for regular inodes
block: disable block device DAX by default
ocfs2: unlock inode if deleting inode from orphan fails
mm: ASLR: use get_random_long()
drivers: char: random: add get_random_long()
mm: numa: quickly fail allocations for NUMA balancing on full nodes
mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Enumeration:
Revert x86 pcibios_alloc_irq() to fix regression (Bjorn Helgaas)
Marvell MVEBU host bridge driver:
Restrict build to 32-bit ARM (Thierry Reding)"
* tag 'pci-v4.5-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: mvebu: Restrict build to 32-bit ARM
Revert "PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()"
Revert "PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed"
Revert "x86/PCI: Don't alloc pcibios-irq when MSI is enabled"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small fix to keep OMAP platforms working across a suspend/resume
cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: omap3+: dpll: use non-locking version of clk_get_rate
|
|
Commit d07e22597d1d ("mm: mmap: add new /proc tunable for mmap_base
ASLR") added the ability to choose from a range of values to use for
entropy count in generating the random offset to the mmap_base address.
The maximum value on this range was set to 32 bits for 64-bit x86
systems, but this value could be increased further, requiring more than
the 32 bits of randomness provided by get_random_int(), as is already
possible for arm64. Add a new function: get_random_long() which more
naturally fits with the mmap usage of get_random_int() but operates
exactly the same as get_random_int().
Also, fix the shifting constant in mmap_rnd() to be an unsigned long so
that values greater than 31 bits generate an appropriate mask without
overflow. This is especially important on x86, as its shift instruction
uses a 5-bit mask for the shift operand, which meant that any value for
mmap_rnd_bits over 31 acts as a no-op and effectively disables mmap_base
randomization.
Finally, replace calls to get_random_int() with get_random_long() where
appropriate.
This patch (of 2):
Add get_random_long().
Signed-off-by: Daniel Cashman <dcashman@android.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Kralevich <nnk@google.com>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver uses PCI glue that is only available on 32-bit ARM. This used
to work fine as long as ARCH_MVEBU and ARCH_DOVE were exclusively 32-bit,
but there's a patch in the pipe to make ARCH_MVEBU also available on 64-bit
ARM.
[bhelgaas: changelog; patch is coming but not merged yet]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and
pcibios_free_irq()") appeared in v4.3 and helps support IOAPIC hotplug.
Олег reported that the Elcus-1553 TA1-PCI driver worked in v4.2 but not
v4.3 and bisected it to 991de2e59090. Sunjin reported that the RocketRAID
272x driver worked in v4.2 but not v4.3. In both cases booting with
"pci=routirq" is a workaround.
I think the problem is that after 991de2e59090, we no longer call
pcibios_enable_irq() for upstream bridges. Prior to 991de2e59090, when a
driver called pci_enable_device(), we recursively called
pcibios_enable_irq() for upstream bridges via pci_enable_bridge().
After 991de2e59090, we call pcibios_enable_irq() from pci_device_probe()
instead of the pci_enable_device() path, which does *not* call
pcibios_enable_irq() for upstream bridges.
Revert 991de2e59090 to fix these driver regressions.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=111211
Fixes: 991de2e59090 ("PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()")
Reported-and-tested-by: Олег Мороз <oleg.moroz@mcc.vniiem.ru>
Reported-by: Sunjin Yang <fan4326@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
CC: Jiang Liu <jiang.liu@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are two reverts of recent PCI-related ACPI core changes (one of
which caused some systems to crash on boot and the other was a cleanup
on top of it) and a devfreq fix for Tegra.
Specifics:
- Revert an ACPI core change related to IRQ management in PCI that
introduced code relying on the use of kmalloc() which turned out to
also run during early init when that's not available yet and caused
some systems to crash on boot for this reason along with a cleanup
on top of it (Rafael Wysocki).
- Prevent devfreq from flooding the kernel log with useless messages
on Tegra (which started to happen after some recent changes in the
devfreq core) by fixing the driver to follow the documentation and
the core's expectations in its ->target callback (Tomeu Vizoso)"
* tag 'pm+acpi-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI, PCI, irq: remove interrupt count restriction"
Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
PM / devfreq: tegra: Set freq in rate callback
|
|
* pm-devfreq:
PM / devfreq: tegra: Set freq in rate callback
* acpi-pci:
Revert "ACPI, PCI, irq: remove interrupt count restriction"
Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SuperH driver fix from Simon Horman:
"Restore legacy clock domain on SuperH platforms"
* tag 'renesas-sh-drivers-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Restore legacy clock domain on SuperH platforms
|
|
Pull drm fixes from Dave Airlie:
"This is a bit larger than Id like, but I asked the Intel guys to pull
in some Skylake fixes in the possibly vain hope that Skylake might be
more functional now that I'm seeing production hardware shipping.
For i915, it's mostly the same patch in a few places, making sure the
hw doesn't turn off when we are programming it.
Apart from that are two nouveau fixes, one for a module defer bug, and
one for using nouveau on new Lenovo P50 models.
Then there are a bunch of AMDGPU fixes, one is a fix for v4.4 vblank
regressions, and some PM fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/nouveau/disp/dp: ensure sink is powered up before attempting link training
drm/nouveau: platform: Fix deferred probe
drm/amdgpu: disable direct VM updates when vm_debug is set
amdgpu: fix NULL pointer dereference at tonga_check_states_equal
drm/i915/gen9: Verify and enforce dc6 state writes
drm/i915/gen9: Check for DC state mismatch
drm/radeon/pm: adjust display configuration after powerstate
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu/pm: add some checks for PX
drm/amdgpu: fix locking in force performance level
drm/amdgpu/gfx8: fix priv reg interrupt enable
drm/i915/skl: Ensure HW is powered during DDB HW state readout
drm/i915/lvds: Ensure the HW is powered during HW state readout
drm/i915/hdmi: Ensure the HW is powered during HW state readout
drm/i915/dsi: Ensure the HW is powered during HW state readout
drm/i915/dp: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered when accessing the CRC HW block
drm/i915/ddi: Ensure the HW is powered during HW state readout
drm/i915/crt: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered during HW access in assert_pipe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Two fixes for compatibility with the ACPI 6.1 specification.
Without these fixes multi-interface DIMMs will fail to be probed, and
address range scrub commands to find memory errors will give results
that the kernel will mis-interpret. For multi-interface DIMMs Linux
will accept either the original 6.0 implementation or 6.1.
For address range scrub we'll only support 6.1 since ACPI formalized
this DSM differently than the original example [1] implemented in
v4.2. The expectation is that production systems will only ever ship
the ACPI 6.1 address range scrub command definition.
- The wider async address range scrub work targeting 4.6 discovered
that the original synchronous implementation in 4.5 is not sizing its
return buffer correctly.
- Arnd caught that my recent fix to the size of the pfn_t flags missed
updating the flags variable used in the pmem driver.
- Toshi found that we mishandle the memremap() return value in
devm_memremap().
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm: use 'u64' for pfn flags
devm_memremap: Fix error value when memremap failed
nfit: update address range scrub commands to the acpi 6.1 format
libnvdimm, tools/testing/nvdimm: fix 'ars_status' output buffer sizing
nfit: fix multi-interface dimm handling, acpi6.1 compatibility
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Add a regression fix for changed sysfs path of bq27xxx_battery and
update MAINTAINERS file"
* tag 'for-v4.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: bq27xxx_battery: Restore device name
MAINTAINERS: update bq27xxx driver
|
|
This can happen under some annoying circumstances, and is a quick fix
until more substantial changes can be made.
Fixed eDP mode changes on (at least) the Lenovo P50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
The error cleanup paths aren't quite correct and will crash upon
deferred probe.
Cc: stable@vger.kernel.org # v4.3+
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
CONFIG_ARCH_SHMOBILE is not only enabled for Renesas ARM platforms
(which are DT based and multi-platform), but also on a select set of
Renesas SuperH platforms (SH7722/SH7723/SH7724/SH7343/SH7366). Hence
since commit 0ba58de231066e47 ("drivers: sh: Get rid of
CONFIG_ARCH_SHMOBILE_MULTI"), the legacy clock domain is no longer
installed on these SuperH platforms, and module clocks may not be
enabled when needed, leading to driver failures.
To fix this, add an additional check for CONFIG_OF.
Fixes: 0ba58de231066e47 ("drivers: sh: Get rid of CONFIG_ARCH_SHMOBILE_MULTI").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
This is a bit large, but it really helps Skylake bugs we are seeing
on a number of laptops.
Most of the commits are quite similar, ensuring the display power
doesn't vanish under us during hardware access. Also do note that it's
not just Skylake that's affected.
* tag 'drm-intel-fixes-2016-02-22' of git://anongit.freedesktop.org/drm-intel:
drm/i915/gen9: Verify and enforce dc6 state writes
drm/i915/gen9: Check for DC state mismatch
drm/i915/skl: Ensure HW is powered during DDB HW state readout
drm/i915/lvds: Ensure the HW is powered during HW state readout
drm/i915/hdmi: Ensure the HW is powered during HW state readout
drm/i915/dsi: Ensure the HW is powered during HW state readout
drm/i915/dp: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered when accessing the CRC HW block
drm/i915/ddi: Ensure the HW is powered during HW state readout
drm/i915/crt: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered during HW access in assert_pipe
drm/i915: Ensure the HW is powered when disabling VGA
drm/i915/ibx: Ensure the HW is powered during PLL HW readout
drm/i915: Ensure the HW is powered during display pipe HW readout
drm/i915: Add helper to get a display power ref if it was already enabled
|
|
into drm-fixes
A few radeon and amdgpu fixes for 4.5. A few further fixes for the vblank
regressions in 4.4 and a couple of other minor fixes.
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: disable direct VM updates when vm_debug is set
amdgpu: fix NULL pointer dereference at tonga_check_states_equal
drm/radeon/pm: adjust display configuration after powerstate
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu/pm: add some checks for PX
drm/amdgpu: fix locking in force performance level
drm/amdgpu/gfx8: fix priv reg interrupt enable
drm/amdgpu: Don't hang in amdgpu_flip_work_func on disabled crtc.
drm/radeon: Don't hang in radeon_flip_work_func on disabled crtc. (v2)
|
|
That should make user space bugs more obvious.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The event_data passed from pem_fini was not cleared upon initialization.
This caused NULL checks to pass and cast_const_phw_tonga_power_state to
attempt to dereference an invalid pointer. Clear the event_data in
pem_init and pem_fini before calling pem_handle_event.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Bradley Pankow <btpankow@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
|
|
Revert commit b5bd02695471 (ACPI, PCI, irq: remove interrupt count
restriction) that introduced a boot regression on some systems
where it caused kmalloc() to be used too early.
Link: http://marc.info/?l=linux-acpi&m=145580159209240&w=2
Reported-by: Nalla, Ravikanth <ravikanth.nalla@hpe.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Revert commit 0971686954f9 "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
that depends on commit b5bd02695471 (ACPI, PCI, irq: remove interrupt
count restriction) which introduced a regression and needs to be
reverted for this reason.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a 112 byte leak for each IO request that is requeued while DM
multipath is handling faults due to path failures.
This leak does not happen if blk-mq DM multipath is used. It only
occurs if .request_fn DM multipath is stacked ontop of blk-mq paths
(e.g. scsi-mq devices)"
* tag 'dm-4.5-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix dm_rq_target_io leak on faults with .request_fn DM w/ blk-mq paths
|
|
Pull MMC fix from Ulf Hansson:
"Here's an mmc fix intended for v4.5 rc6.
MMC host:
- omap_hsmmc: Fix PM regression for deferred probe"
* tag 'mmc-v4.5-rc4' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: omap_hsmmc: Fix PM regression with deferred probe for pm_runtime_reinit
|
|
A recent bugfix changed pfn_t to always be 64-bit wide, but did not
change the code in pmem.c, which is now broken on 32-bit architectures
as reported by gcc:
In file included from ../drivers/nvdimm/pmem.c:28:0:
drivers/nvdimm/pmem.c: In function 'pmem_alloc':
include/linux/pfn_t.h:15:17: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define PFN_DEV (1ULL << (BITS_PER_LONG_LONG - 3))
This changes the intermediate pfn_flags in struct pmem_device to
be 64 bit wide as well, so they can store the flags correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db78c22230d0 ("mm: fix pfn_t vs highmem")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The original format of these commands from the "NVDIMM DSM Interface
Example" [1] are superseded by the ACPI 6.1 definition of the "NVDIMM Root
Device _DSMs" [2].
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
[2]: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
"9.20.7 NVDIMM Root Device _DSMs"
Changes include:
1/ New 'restart' fields in ars_status, unfortunately these are
implemented in the middle of the existing definition so this change
is not backwards compatible. The expectation is that shipping
platforms will only ever support the ACPI 6.1 definition.
2/ New status values for ars_start ('busy') and ars_status ('overflow').
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit ac33cdb16681 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
As per the documentation of the devfreq_dev_profile.target callback, set
the freq argument to the new frequency before returning.
This caused endless messages like this after recent changes in the core:
devfreq 6000c800.actmon: Couldn't update frequency transition information.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
As the code in this file is being executed within irq context in some
cases, we must avoid the clk_get_rate which uses mutex internally.
Switch the code to use clk_hw_get_rate instead which is non-locking.
This fixes an issue where PM runtime will hang the system if enabled
with a serial console before a suspend-resume cycle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: a53ad8ef3dcc ("clk: ti: Convert to clk_hw based provider APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
* tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
xen/pcifront: Report the errors better.
xen/pciback: Save the number of MSI-X entries to be copied later.
xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
xen: fix potential integer overflow in queue_reply
xen/arm: correctly handle DMA mapping of compound pages
xen/scsiback: avoid warnings when adding multiple LUNs to a domain
xen/scsiback: correct frontend counting
|
|
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
|
