| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
spi: Fix WARN when removing spi-fsl-spi module
spi/imx: Fix spi-imx when the hardware SPI chipselects are used
|
|
If CPM mode is not used, the fsl_dummy_rx variable is never allocated. When
the cleanup attempts to free it, the reference count is zero and a WARN is
generated. The same CPM mode check used in the initialize is applied to the
free as well.
Tested on 2.6.33 with the previous spi_mpc8xxx driver. The renamed
spi-fsl-spi driver looks to have the same problem.
Signed-off-by: Jeff Harris <jeff_harris@kentrox.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
sector_t can be different types, so cast it to its largest possible
type.
drivers/scsi/qla2xxx/qla_isr.c:1509:5: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'sector_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SCSI_ISCI needs to select SCSI_SAS_HOST_SMP to ensure that all
needed symbols are available to it.
Fixes this build error:
ERROR: "try_test_sas_gpio_gp_bit" [drivers/scsi/isci/isci.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set. Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit 18b4fada275dd2b6dd9db904ddf70fe39e272222.
This code was correct, apologies to anyone who noticed things broke.
revert contents are different due to another commit in between.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* 'for-linus' of git://git.selinuxproject.org/~jmorris/linux-security:
TPM: Zero buffer after copying to userspace
TPM: Call tpm_transmit with correct size
TPM: tpm_nsc: Fix a double free of pdev in cleanup_nsc
TPM: TCG_ATMEL should depend on HAS_IOPORT
|
|
Since the buffer might contain security related data it might be a good idea to
zero the buffer after we have copied it to userspace.
This got assigned CVE-2011-1162.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
This patch changes the call of tpm_transmit by supplying the size of the
userspace buffer instead of TPM_BUFSIZE.
This got assigned CVE-2011-1161.
[The first hunk didn't make sense given one could expect
way less data than TPM_BUFSIZE, so added tpm_transmit boundary
check over bufsiz instead
The last parameter of tpm_transmit() reflects the amount
of data expected from the device, and not the buffer size
being supplied to it. It isn't ideal to parse it directly,
so we just set it to the maximum the input buffer can handle
and let the userspace API to do such job.]
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
platform_device_unregister() will release all resources
and remove it from the subsystem, then drop reference count by
calling platform_device_put().
We should not call kfree(pdev) after platform_device_unregister(pdev).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
On m68k, I get:
drivers/char/tpm/tpm_atmel.h: In function ‘atmel_get_base_addr’:
drivers/char/tpm/tpm_atmel.h:129: error: implicit declaration of function ‘ioport_map’
drivers/char/tpm/tpm_atmel.h:129: warning: return makes pointer from integer without a cast
The code in tpm_atmel.h supports PPC64 (using the device tree and ioremap())
and "anything else" (using ioport_map()). However, ioportmap() is only
available on platforms that set HAS_IOPORT.
Although PC64 seems to have HAS_IOPORT, a "depends on HAS_IOPORT" should work,
but I think it's better to expose the special PPC64 handling explicit using
"depends on PPC64 || HAS_IOPORT".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
As the Amiga Zorro II address space is limited to 8.5 MiB and Zorro
devices can contain only one BAR, several Amiga Zorro II expansion
boards (mainly graphics cards) contain multiple Zorro devices: a small
one for the control registers and one (or more) for the graphics memory.
The conversion of cirrusfb to the new driver framework introduced a
regression: the driver contains a zorro_driver for the first Zorro
device, and uses the (old) zorro_find_device() call to find the second
Zorro device.
However, as the Zorro core calls device_register() as soon as a Zorro
device is identified, it may not have identified the second Zorro device
belonging to the same physical Zorro expansion card. Hence cirrusfb
could no longer find the second part of the Picasso II graphics card,
causing a NULL pointer dereference.
Defer the registration of Zorro devices with the driver framework until
all Zorro devices have been identified to fix this.
Note that the alternative solution (modifying cirrusfb to register a
zorro_driver for all Zorro devices belonging to a graphics card, instead
of only for the first one, and adding a synchronization mechanism to
defer initialization until all have been found), is not an option, as on
some cards one device may be optional (e.g. the second bank of 2 MiB of
graphics memory on the Picasso IV in Zorro II mode).
Reported-by: Ingo Jürgensmann <ij@2011.bluespice.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://github.com/davem330/net: (27 commits)
xfrm: Perform a replay check after return from async codepaths
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
ixgbe: fix possible null buffer error
tg3: fix VLAN tagging regression
net: pxa168: Fix build errors by including interrupt.h
netconsole: switch init_netconsole() to late_initcall
gianfar: Fix overflow check and return value for gfar_get_cls_all()
ppp_generic: fix multilink fragment MTU calculation (again)
GRETH: avoid overwrite IP-stack's IP-frags checksum
GRETH: RX/TX bytes were never increased
ipv6: fix a possible double free
b43: Fix beacon problem in ad-hoc mode
Bluetooth: add support for 2011 mac mini
Bluetooth: Add MacBookAir4,1 support
Bluetooth: Fixed BT ST Channel reg order
r8169: do not enable the TBI for anything but the original 8169.
r8169: remove erroneous processing of always set bit.
r8169: fix WOL setting for 8105 and 8111evl
r8169: add MODULE_FIRMWARE for the firmware of 8111evl
r8169: fix the reset setting for 8111evl
...
|
|
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
|
|
When no floppy is found the module code can be released while a timer
function is pending or about to be executed.
CPU0 CPU1
floppy_init()
timer_softirq()
spin_lock_irq(&base->lock);
detach_timer();
spin_unlock_irq(&base->lock);
-> Interrupt
del_timer();
return -ENODEV;
module_cleanup();
<- EOI
call_timer_fn();
OOPS
Use del_timer_sync() to prevent this.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It seems that at least one PPC machine would occasionally give a (valid) 0 as
the return value from dma_map, this caused the ixgbe code to not work
correctly. A fix is pending in the PPC tree to not return 0 from dma map, but
we can also fix the driver to make sure we don't mess up in other arches as
well.
This patch is applicable to all current stable kernels.
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=683611
Reported-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: stable@kernel.org
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 92cd3a17ce9c719abb4c28dee3438e0c641f8de4
tg3: Simplify tx bd assignments
broke VLAN tagging on outbound packets.
It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this
is not set anywhere. So vlan never gets set, and
all packets are sent with vlan=0.
v2: We can just remove the test. vlan_tx_tag_present
is valid regardless of whether the 802.1q module
is built.
Tested on BCM5721 rev 11.
Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit c5f5c4db3938 ("staging: zcache: fix crash on high memory
swap") cleancache crashes on the first successful get. This was caused
by a remaining virt_to_page() call in zcache_pampd_get_data_and_free()
that only gets run in the cleancache path.
The patch converts the virt_to_page() to struct page casting like was
done for other instances in c5f5c4db3938.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Tested-By: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a6b7a407865aab9f849dd99a71072b7cd1175116 removed
linux/interrupt.h from netdevice.h. This fixes below build failure
drivers/net/pxa168_eth.c: In function 'pxa168_eth_collect_events':
drivers/net/pxa168_eth.c:866: error: 'IRQ_NONE' undeclared (first use in this function)
drivers/net/pxa168_eth.c:866: error: (Each undeclared identifier is reported only once
drivers/net/pxa168_eth.c:866: error: for each function it appears in.)
drivers/net/pxa168_eth.c: At top level:
drivers/net/pxa168_eth.c:913: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'pxa168_eth_int_handler'
drivers/net/pxa168_eth.c: In function 'pxa168_eth_open':
drivers/net/pxa168_eth.c:1133: error: implicit declaration of function 'request_irq'
drivers/net/pxa168_eth.c:1133: error: 'pxa168_eth_int_handler' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1134: error: 'IRQF_DISABLED' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1160: error: implicit declaration of function 'free_irq'
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a
regression that netconsole does not work if netconsole and network
device driver are build into kernel, because netconsole is linked
before network device driver.
Andrew Morton suggested to fix this with initcall ordering.
Fixes it by switching init_netconsole() to late_initcall.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function may currently fill one entry beyond the end of the
array it is given. It also doesn't return an error code in case
it does detect overflow.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using MLPPP, the maximum size of a fragment is incorrectly
calculated with an offset of -2.
This patch reverses the changes in the patch found here:
http://marc.info/?l=linux-netdev&m=123541324010539&w=2
The value of hdrlen includes the size of both the 2-byte PPP protocol
field and the 2- or 4-byte multilink header (2+4=6 for long sequence
numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says
that the MRU that is negotiated (i.e., the MTU of the sending system)
includes only the PPP payload but not the protocol field, thus the
correct MTU should be the link's MTU minus the multilink header (mtu -
(hdrlen-2)).
The incorrect calculation causes Linux to fragment packets to a size two
bytes smaller than the allowed MTU. While not technically illegal, this
behaviour confounds MRU-tuning to avoid PPP-layer fragmentation.
Signed-off-by: Henry Wong <henry@stuffedcow.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GRETH GBIT core does not do checksum offloading for IP
segmentation. This patch adds a check in the xmit function to
determine if the stack has calculated the checksum for us.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
|
|
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use the passed watchdog_device instead of the static global variable when
testing and setting the status in watchdog_ping, watchdog_start, and
watchdog_stop. Note that the callers of these functions are actually
passing the static global variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, iommu: Mark DMAR IRQ as non-threaded
genirq: Make irq_shutdown() symmetric vs. irq_startup again
|
|
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf375 ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
enabled
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects
|
|
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
mfd: Fix omap-usb-host build failure
mfd: Make omap-usb-host TLL mode work again
mfd: Set MAX8997 irq pointer
mfd: Fix initialisation of tps65910 interrupts
mfd: Check for twl4030-madc NULL pointer
mfd: Copy the device pointer to the twl4030-madc structure
mfd: Rename wm8350 static gpio_set_debounce()
mfd: Fix value of WM8994_CONFIGURE_GPIO
|
|
The BO blit code inconsistenly handled the page size. This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well. Switch the driver blit callbacks to take num pages in GPU
page units.
Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.
v2: incorporate suggestions from Michel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
cur_pages is the number of pages per loop iteration.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* git://github.com/davem330/net: (62 commits)
ipv6: don't use inetpeer to store metrics for routes.
can: ti_hecc: include linux/io.h
IRDA: Fix global type conflicts in net/irda/irsysctl.c v2
net: Handle different key sizes between address families in flow cache
net: Align AF-specific flowi structs to long
ipv4: Fix fib_info->fib_metrics leak
caif: fix a potential NULL dereference
sctp: deal with multiple COOKIE_ECHO chunks
ibmveth: Fix checksum offload failure handling
ibmveth: Checksum offload is always disabled
ibmveth: Fix issue with DMA mapping failure
ibmveth: Fix DMA unmap error
pch_gbe: support ML7831 IOH
pch_gbe: added the process of FIFO over run error
pch_gbe: fixed the issue which receives an unnecessary packet.
sfc: Use 64-bit writes for TX push where possible
Revert "sfc: Use write-combining to reduce TX latency" and follow-ups
bnx2x: Fix ethtool advertisement
bnx2x: Fix 578xx link LED
bnx2x: Fix XMAC loopback test
...
|
|
* 'fixes' of git://git.user.in-berlin.de/s5r6/linux1394:
firewire: ohci: add no MSI quirk for O2Micro controller
|
|
* '3.1-rc-fixes' of git://linux-iscsi.org/target-pending:
iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets
iscsi-target: Disable markers + remove dangerous local scope array usage
target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended
tcm_fc: Work queue based approach instead of managing own thread and event based mechanism
tcm_fc: Invalidation of DDP context for FCoE target in error conditions
target: Fix race between multiple invocations of target_qf_do_work()
|
|
Today I noticed that the usb bluetooth adapter (BCM2046B1) on my 2011
mac mini was not working. I've created a patch to get it going.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Reordered the BT ST channel registration, to make sure that the
event channel is registered before all others. This prevents a
situation where incoming events may cause kernel panic in the ST
driver if the event channel is not yet registered to handle
incoming events.In addition, the deregistration of the channels
was also modified, to be in the reversed order of the registration,
to allow the event channel to be the last one unregistered.
Signed-off-by: Chen Ganir <chen.ganir@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The TBI bit in PHYStatus is reserved on anything but the oldest 8169.
Nobody complained after I disabled it for the 8168 and the 810x (see
66ec5d4fb1ce6f0bd9df4bc4b758f0916d9f37ab).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
When set, RxFOVF (resp. RxBOVF) is always 1 (resp. 0).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
|
|
rtl8105, rtl8111E, and rtl8111evl need enable RxConfig bit 1 ~ 3
for supporting wake on lan.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
|
|
Add MODULE_FIRMWARE for the firmware of RTL8111E-VL
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
|
