| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do a release_mem_region of the hcd resource. Without this the
subsequent insertion of module fails in request_mem_region.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow udev to autoload the module when booting with device-tree
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes and other good stuff in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are two fixes that came in this week, one for a regression we
introduced in 3.10 in the GIC interrupt code, and the other one fixes
a typo in newly introduced code"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
irqchip: gic: call gic_cpu_init() as well in CPU_STARTING_FROZEN case
ARM: dts: Correct the base address of pinctrl_3 on Exynos5250
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg Kroah-Hartman:
"Here's a single patch for the firmware core that resolves a reported
oops in the firmware core that people have been hitting."
* tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware loader: fix use-after-free by double abort
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are two USB patches for 3.10.
One updates the Kconfig wording for CONFIG_USB_PHY to make it,
hopefully, more obvious what this option is (I know you complained
about this when it hit the tree.) The other is a new device id for a
driver"
* tag 'usb-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ti_usb_3410_5052: new device id for Abbot strip port cable
usb: phy: Improve Kconfig help for CONFIG_USB_PHY
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pul tty fixes from Greg Kroah-Hartman:
"Here are two tty core fixes that resolve some regressions that have
been reported recently. Both tiny fixes, but needed"
* tag 'tty-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix transient pty write() EIO
tty/vt: Return EBUSY if deallocating VT1 and it is busy
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Included is the recent tcm_qla2xxx residual underrun length fix from
Roland, along with Joern's iscsi-target patch for session_lock
breakage within iscsit_stop_time2retain_timer() code. Both are CC'ed
to stable.
The remaining two are specific to recent iscsi-target + iser
conversion changes. One drops some left-over debug noise, and Andy's
patch fixes configfs attribute handling during an explicit network
portal feature bit disable when iser-target is unsupported."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Remove left over v3.10-rc debug printks
target/iscsi: Fix op=disable + error handling cases in np_store_iser
tcm_qla2xxx: Fix residual for underrun commands that fail
target/iscsi: don't corrupt bh_count in iscsit_stop_time2retain_timer()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Another set of fixes for Kernel 3.10.
This series contain:
- two Kbuild fixes for randconfig
- a buffer overflow when using rtl28xuu with r820t tuner
- one clk fixup on exynos4-is driver"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Fix build when drivers are builtin and frontend modules
[media] s5p makefiles: don't override other selections on obj-[ym]
[media] exynos4-is: Fix FIMC-IS clocks initialization
[media] rtl28xxu: fix buffer overflow when probing Rafael Micro r820t tuner
|
|
Pull drm radeon fixes from Dave Airlie:
"One core fix, but mostly radeon fixes for s/r and big endian UVD
support, and a fix to stop the GPU being reset for no good reason, and
crashing people's machines."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: update lockup tracking when scheduling in empty ring
drm/prime: Honor requested file flags when exporting a buffer
drm/radeon: fix UVD on big endian
drm/radeon: fix write back suspend regression with uvd v2
drm/radeon: do not try to uselessly update virtual memory pagetable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
- Fix for a regression causing a failure to turn on some devices on
some systems during initialization introduced by a recent revert of
an ACPI PM change that broke something else. Fortunately, we know
exactly what devices are affected, so we can add a fix just for them
leaving everyone else alone.
- ACPI power resources initialization fix preventing a NULL pointer
from being dereferenced in the acpi_add_power_resource() error code
path.
- ACPI dock station driver fix that adds missing locking to
write_undock().
- ACPI resources allocation fix changing the scope of an old workaround
so that it doesn't affect systems that aren't actually buggy. This
was reported a couple of days ago to fix DMA problems on some new
platforms so we need it in -stable. From Mika Westerberg.
* tag 'acpi-3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / LPSS: Power up LPSS devices during enumeration
ACPI / PM: Fix error code path for power resources initialization
ACPI / dock: Take ACPI scan lock in write_undock()
ACPI / resources: call acpi_get_override_irq() only for legacy IRQ resources
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This fixes a problem preventing the kernel and userland librbd
libraries from sharing data with the new format 2 images"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use the correct length for format 2 object names
|
|
Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Writing 0 when iser was not previously enabled, so succeed but do
nothing so that user-space code doesn't need a try: catch block
when ib_isert logic is not available.
Also, return actual error from add_network_portal using PTR_ERR
during op=enable failure.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
into drm-fixes
One user visible fix to stop misreport GPU hangs and subsequent resets.
* 'drm-fixes-3.10' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: update lockup tracking when scheduling in empty ring
|
|
There might be issue with lockup detection when scheduling on an
empty ring that have been sitting idle for a while. Thus update
the lockup tracking data when scheduling new work in an empty ring.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are a large number of reports that the media build is
not compiling when some drivers are compiled as builtin, while
the needed frontends are compiled as module.
On the last one of such reports:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: saa7134-dvb.c:undefined reference to `zl10039_attach'
The .config file has:
CONFIG_VIDEO_SAA7134=y
CONFIG_VIDEO_SAA7134_DVB=y
# CONFIG_MEDIA_ATTACH is not set
CONFIG_DVB_ZL10039=m
And it produces all those errors:
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x2f263e): undefined reference to `tea5767_attach'
tuner-core.c:(.text+0x2f273e): undefined reference to `tda9887_attach'
drivers/built-in.o: In function `tuner_probe':
tuner-core.c:(.text+0x2f2d20): undefined reference to `tea5767_autodetection'
drivers/built-in.o: In function `av7110_attach':
av7110.c:(.text+0x330bda): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330bf7): undefined reference to `stv0299_attach'
av7110.c:(.text+0x330c63): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d09): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330d33): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d5d): undefined reference to `stv0297_attach'
av7110.c:(.text+0x330dbe): undefined reference to `stv0299_attach'
drivers/built-in.o: In function `tuner_attach_dtt7520x':
ngene-cards.c:(.text+0x3381cb): undefined reference to `dvb_pll_attach'
drivers/built-in.o: In function `demod_attach_lg330x':
ngene-cards.c:(.text+0x33828a): undefined reference to `lgdt330x_attach'
drivers/built-in.o: In function `demod_attach_stv0900':
ngene-cards.c:(.text+0x3383d5): undefined reference to `stv090x_attach'
drivers/built-in.o: In function `cineS2_probe':
ngene-cards.c:(.text+0x338b7f): undefined reference to `drxk_attach'
drivers/built-in.o: In function `configure_tda827x_fe':
saa7134-dvb.c:(.text+0x346ae7): undefined reference to `tda10046_attach'
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347283): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x3472cd): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x34731c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34733c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34735c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x347378): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x3473db): undefined reference to `tda10046_attach'
drivers/built-in.o:saa7134-dvb.c:(.text+0x347502): more undefined references to `tda10046_attach' follow
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347812): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x347951): undefined reference to `mt312_attach'
saa7134-dvb.c:(.text+0x3479a9): undefined reference to `mt312_attach'
>> saa7134-dvb.c:(.text+0x3479c1): undefined reference to `zl10039_attach'
This is happening because a builtin module can't use directly a symbol
found on a module. By enabling CONFIG_MEDIA_ATTACH, the configuration
becomes valid, as dvb_attach() macro loads the module if needed, making
the symbol available to the builtin module.
While this bug started to appear after the patches that use IS_DEFINED
macro (like changeset 7b34be71db533f3e0cf93d53cf62d036cdb5418a), this
bug is a way ancient than that.
The thing is that, before the IS_DEFINED() patches, the logic used to be:
&& defined(MODULE))
struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
u8 i2c_addr,
struct i2c_adapter *i2c);
static inline struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
u8 i2c_addr,
struct i2c_adapter *i2c)
{
printk(KERN_WARNING "%s: driver disabled by Kconfig\n", __func__);
return NULL;
}
The above code, with the .config file used, was evoluting to FALSE
(instead of TRUE as it should be, as CONFIG_DVB_ZL10039 is 'm'),
and were adding the static inline code at saa7134-dvb, instead
of the external call. So, while it weren't producing any compilation
error, the code weren't working either.
So, as the overhead for using CONFIG_MEDIA_ATTACH is minimal, just
enable it, if MODULES is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Commit c011470 (irqchip: gic: Perform the gic_secondary_init() call via
CPU notifier) moves gic_secondary_init() that used to be called in
.smp_secondary_init hook into a notifier call. But it changes the
system behavior a little bit. Before the commit, gic_cpu_init()
is called not only when kernel brings up the secondary cores but also
when system resuming procedure hot-plugs the cores back to kernel.
While after the commit, the function will not be called in the latter
case, where the 'action' will not be CPU_STARTING but
CPU_STARTING_FROZEN. This behavior difference at least causes the
following suspend/resume regression on imx6q.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
PM: suspend of devices complete after 5.930 msecs
PM: suspend devices took 0.010 seconds
PM: late suspend of devices complete after 0.343 msecs
PM: noirq suspend of devices complete after 0.828 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
INFO: rcu_sched detected stalls on CPUs/tasks: { 1 2 3} (detected by 0, t=2102 jiffies, g=4294967169, c=4294967168, q=17)
Task dump for CPU 1:
swapper/1 R running 0 0 1 0x00000000
Backtrace:
[<bf895ff4>] (0xbf895ff4) from [<00000000>] ( (null))
Backtrace aborted due to bad frame pointer <8007ccdc>
Task dump for CPU 2:
swapper/2 R running 0 0 1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] ( (null))
Backtrace aborted due to bad frame pointer <00000002>
Task dump for CPU 3:
swapper/3 R running 0 0 1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] ( (null))
Fix the regression by checking 'action' being CPU_STARTING_FROZEN to
have gic_cpu_init() called for secondary cores when system resumes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The $obj-m/$obj-y vars should be adding new modules to build, not
overriding it. So, it should never use
$obj-y := foo.o
instead, it should use:
$obj-y += foo.o
Failing to do that is very bad, as it will suppress needed modules.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 7cd8407 (ACPI / PM: Do not execute _PS0 for devices without
_PSC during initialization) introduced a regression on some systems
with Intel Lynxpoint Low-Power Subsystem (LPSS) where some devices
need to be powered up during initialization, but their device objects
in the ACPI namespace have _PS0 and _PS3 only (without _PSC or power
resources).
To work around this problem, make the ACPI LPSS driver power up
devices it knows about by using a new helper function
acpi_device_fix_up_power() that does all of the necessary
sanity checks and calls acpi_dev_pm_explicit_set() to put the
device into D0.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 781d737 (ACPI: Drop power resources driver) introduced a
bug in the power resources initialization error code path causing
a NULL pointer to be referenced in acpi_release_power_resource()
if there's an error triggering a jump to the 'err' label in
acpi_add_power_resource(). This happens because the list_node
field of struct acpi_power_resource has not been initialized yet
at this point and doing a list_del() on it is a bad idea.
To prevent this problem from occuring, initialize the list_node
field of struct acpi_power_resource upfront.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since commit 3757b94 (ACPI / hotplug: Fix concurrency issues and
memory leaks) acpi_bus_scan() and acpi_bus_trim() must always be
called under acpi_scan_lock, but currently the following scenario
violating that requirement is possible:
write_undock()
handle_eject_request()
hotplug_dock_devices()
dock_remove_acpi_device()
acpi_bus_trim()
Fix that by making write_undock() acquire acpi_scan_lock before
calling handle_eject_request() as appropriate (begin_undock() is
under the lock too in analogy with acpi_dock_deferred_cb()).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
acpi_get_override_irq() was added because there was a problem with
buggy BIOSes passing wrong IRQ() resource for the RTC IRQ. The
commit that added the workaround was 61fd47e0c8476 (ACPI: fix two
IRQ8 issues in IOAPIC mode).
With ACPI 5 enumerated devices there are typically one or more
extended IRQ resources per device (and these IRQs can be shared).
However, the acpi_get_override_irq() workaround forces all IRQs in
range 0 - 15 (the legacy ISA IRQs) to be edge triggered, active high
as can be seen from the dmesg below:
ACPI: IRQ 6 override to edge, high
ACPI: IRQ 7 override to edge, high
ACPI: IRQ 7 override to edge, high
ACPI: IRQ 13 override to edge, high
Also /proc/interrupts for the I2C controllers (INT33C2 and INT33C3) shows
the same thing:
7: 4 0 0 0 IO-APIC-edge INT33C2:00, INT33C3:00
The _CSR method for INT33C2 (and INT33C3) device returns following
resource:
Interrupt (ResourceConsumer, Level, ActiveLow, Shared,,, )
{
0x00000007,
}
which states that this is supposed to be level triggered, active low,
shared IRQ instead.
Fix this by making sure that acpi_get_override_irq() gets only called
when we are dealing with legacy IRQ() or IRQNoFlags() descriptors.
While we are there, correct pr_warning() to print the right triggering
value.
This change turns out to be necessary to make DMA work correctly on
systems based on the Intel Lynxpoint PCH (Platform Controller Hub).
[rjw: Changelog]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ISP clock register content is not preserved over the ISP power domain
off/on cycle. Instead of setting the clock frequencies once at probe time
the clock rates set up is moved to the runtime_resume handler, which is
invoked after the related power domain is already enabled, ensuring the
clocks are properly configured when the device is actively used.
This fixes the FIMC-IS malfunctions and STREAM ON timeout errors accuring
on some boards:
[ 59.860000] fimc_is_general_irq_handler:583 ISR_NDONE: 5: 0x800003e8, IS_ERROR_UNKNOWN
[ 59.860000] fimc_is_general_irq_handler:586 IS_ERROR_TIME_OUT
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
into drm-fixes
Alex writes:
Remove some harmless but confusing VM related error messages
fix a regression with suspend and UVD,
fix UVD on big endian.
* 'drm-fixes-3.10' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix UVD on big endian
drm/radeon: fix write back suspend regression with uvd v2
drm/radeon: do not try to uselessly update virtual memory pagetable
|
|
The DRM PRIME API passes file flags to the driver for the exported
buffer. Honor them instead of hardcoding 0600.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The C8000 workstation (64 bit kernel only) has a somewhat different
serial port configuration than other models.
Thomas Bogendoerfer sent a patch to fix this in September 2010, which
was now minimally modified by me.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
usb_hub_to_struct_hub() can return NULL in some unlikely cases.
Add checks where appropriate, or pass the hub pointer as an additional
argument if it's known to be valid.
The places it makes sense to check usb_hub_to_struct_hub()
are picked based on feedback from Alan Stern.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fail and free the container context in case dma_pool_alloc() can't allocate
the raw context data part of it
This patch should be backported to kernels as old as 2.6.31, that
contain the commit d115b04818e57bdbc7ccde4d0660b15e33013dc8 "USB: xhci:
Support for 64-byte contexts".
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Remove BUG() calls from the driver.
Hi Greg,
This patchset removes instances of BUG() from the xHCI driver. It adds code to
gracefully handle failures by returning standard error values, and changing the
driver to handle those failure cases. These are against Greg's usb-next
branch, and are not marked for stable.
Please queue for 3.11.
Sarah Sharp
|
|
Add the missing unlock before return from function geth_alloc()
in the error handling case.
Introduced by commit 02832e56f88a981474ee4c7c141f46fc1b4454f4.
(usb: gadget: f_subset: add configfs support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the missing unlock before return from function ncm_alloc()
in the error handling case.
Introduced by commit e730660378be92b83288b59b824ccdace5cd2652.
(usb: gadget: f_ncm: add configfs support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the missing unlock before return from function ecm_alloc()
in the error handling case.
Introduced by commit da92801c647cdebfd45001fd6aaecb8f0be7f56b.
(usb: gadget: f_ecm: add configfs support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fw_priv->buf is accessed in both request_firmware_load() and
writing to sysfs file of 'loading' context, but not protected
by 'fw_lock' entirely. The patch makes sure that access on
'fw_priv->buf' is protected by the lock.
So fixes the double abort problem reported by nirinA raseliarison:
http://lkml.org/lkml/2013/6/14/188
Reported-and-tested-by: nirinA raseliarison <nirina.raseliarison@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The previous text confused users by not describing the very common
(e.g. x86 PC) sitations where no PHY driver is necessary.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Series of fixes for 3.10. There are some usual driver fixes (mostly
on s5p/exynos playform drivers), plus some fixes at V4L2 core"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (40 commits)
[media] soc_camera: error dev remove and v4l2 call
[media] sh_veu: fix the buffer size calculation
[media] sh_veu: keep power supply until the m2m context is released
[media] sh_veu: invoke v4l2_m2m_job_finish() even if a job has been aborted
[media] v4l2-ioctl: don't print the clips list
[media] v4l2-ctrls: V4L2_CTRL_CLASS_FM_RX controls are also valid radio controls
[media] cx88: fix NULL pointer dereference
[media] DocBook/media/v4l: update version number
[media] exynos4-is: Remove "sysreg" clock handling
[media] exynos4-is: Fix reported colorspace at FIMC-IS-ISP subdev
[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured
[media] exynos4-is: Prevent NULL pointer dereference when firmware isn't loaded
[media] s5p-mfc: Add NULL check for allocated buffer
[media] s5p-mfc: added missing end-of-lines in debug messages
[media] s5p-mfc: v4l2 controls setup routine moved to initialization code
[media] s5p-mfc: separate encoder parameters for h264 and mpeg4
[media] s5p-mfc: Remove special clock usage in driver
[media] s5p-mfc: Remove unused s5p_mfc_get_decoded_status_v6() function
[media] v4l2: mem2mem: save irq flags correctly
[media] coda: v4l2-compliance fix: add VIDIOC_CREATE_BUFS support
...
|
|
Pull clock framework fixes from Mike Turquette:
"Half of the fixes here are for Exynos5, fixing regressions in CPUfreq
due to the common clock framework conversion as well as one fix which
allows the platform to properly reboot again.
One core framework fix patches up a memory leak, another fixes a build
error for the SPEAr platform and finally a Tegra-specific fix allows
PCIe to initialize properly on that platform again"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
ARM: tegra30: clocks: Fix pciex clock registration
clk: exynos5250: Add CLK_IGNORE_UNUSED flag for pmu clock
clk: spear: fix build error for spear3xx
clk: samsung: Fix pll36xx_recalc_rate to handle kdiv properly
clk: exynos5250: Add sclk_mpll to the parent list of mout_cpu clock
clk: exynos5250: Update cpufreq related clocks for EXYNOS5250
clk: remove notifier from list before freeing it
|
|
This patch removes a double assignment of .start in struct hc_driver
ehci_msp_hc_driver and also makes the code look more tidy.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For PHY mode, the PHYs must be brought out of reset
before the EHCI controller is started.
This patch fixes the issue where USB devices are not found
on Beagleboard/Beagle-xm if USB has been started previously
by the bootloader. (e.g. by "usb start" command in u-boot)
Tested on Beagleboard, Beagleboard-xm and Pandaboard.
Issue present on 3.10 onwards.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under some circumstances it happens that the connected PHY can't be
powered up properly, in which case the cleanup path currently crashes
because it checks the tegra->transceiver field using !IS_ERR(), which
will succeed because it is in fact NULL. Dereferencing that pointer
causes an oops in tegra_ehci_probe().
This patch fixes the issue by adding an additional label into the
cleanup path to separately take down the PHY and the transceiver.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rather than allocating struct tegra_ehci_hcd separately, use struct
ehci_hcd's priv field instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Separate the Tegra on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[swarren, reworked Manjunath's patches to split them more logically,
minor re-order of added lines to better match layout of other split-up
HCD drivers and existing code, add MODULE_DEVICE_TABLE, fix
MODULE_LICENSE, adapted to change in earlier patches which removed the
ehci_driver_overrides addition, removed all PM code and solved circular
dependencies.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Tegra EHCI driver directly calls various functions in the Tegra USB
PHY driver. The reverse is also true; the PHY driver calls into the EHCI
driver. This is problematic when the two are built as modules.
The calls from the PHY to EHCI driver were originally added in commit
bbdabdb "usb: add APIs to access host registers from Tegra PHY", for the
following reasons:
1) The register being touched is an EHCI register, so logically only the
EHCI driver should touch it.
2) (1) implies that some locking may be needed to correctly implement the
r/m/w access to this shared register.
3) We were expecting to pass only the PHY register space to the Tegra PHY
driver, and hence it would not have access to touch the shared
registers.
To solve this, that commit added functions in the EHCI driver to touch the
shared register on behalf of the PHY driver.
In practice, we ended up not having any locking in the implementaiton of
those functions, and I've been led to believe this is safe. Equally, (3)
did not happen either. Hence, it is possible for the PHY driver to touch
the shared register directly.
Given that, this patch moves the code to touch the shared register back
into the PHY driver, to eliminate the module problems. If we actually
need locking or co-ordination in the future, I propose we put the lock
support into some pre-existing core module, or into a third separate
module, in order to avoid the circular dependencies.
I apologize for my contribution to code churn here.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PM routines in ehci-tegra.c use APIs such as ehci_reset(),
ehci_halt(), and ehci_tdi_reset() that would need to be exported to
convert ehci-tegra.c into a separate module from ehci-hcd.c. However,
we'd prefer not to export them.
Instead, simply remove all power management functionality. Runtime PM
was disabled since it didn't work correctly, and system suspend isn't
yet supported in a meaningful way. So, this change doesn't lose any
functionality.
Hopefully the power management logic can be reimplemented in a cleaner
way in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to split ehci-hcd.c into separate modules, handshake() must be
exported. Rename the symbol to add an ehci_ prefix, to avoid any naming
clashes.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[swarren, split Manjunath's patches more logically, limit this change
to export just handshake()]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When this file is built as a module, it needs a MODULE_LICENSE in order
to access many exported symbols.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to build a ULPI PHY driver as a module, this symbol needs to
be exported.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[swarren, reworked Manjunath's patches to split them more logically]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
