summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2008-07-10[HIFN]: Have HW invalidate src and dest descriptors after processingPatrick McHardy1-4/+4
The descriptors need to be invalidated after processing for ring cleanup to work properly and to avoid using an old destination descriptor when the src and cmd descriptors are already set up and the dst descriptor isn't. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Move command descriptor setup to seperate functionPatrick McHardy1-101/+104
Move command descriptor setup to seperate function as preparation for the following DMA setup fixes. Note 1: also fix a harmless typo while moving it: sa_idx is initialized to dma->resi instead of dma->cmdi. Note 2: errors from command descriptor setup are not propagated back, anymore, they can't be handled anyway and all conditions leading to errors should be checked earlier. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Fix max queue length valuePatrick McHardy1-1/+1
All but the last element of the command and result descriptor rings can be used for crypto requests, fix HIFN_QUEUE_LENGTH. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Properly initialize ivsize for CBC modesPatrick McHardy1-0/+3
For combined modes like cbc(aes) the driver is responsible for initializing ivsize. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Use unique driver names for different algosPatrick McHardy1-13/+14
When the CryptoAPI instantiates a new algorithm, it performs a lookup by driver name. Since hifn uses the same name for all modes of one algorithm, the lookup may return an incorrect algorithm. Change the name to use <mode>-<algo>-<devicename> to provide unique names for the different combinations and devices. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Properly handle requests for less than the full scatterlistPatrick McHardy1-10/+10
The scatterlist may contain more data than the crypto request, causing an underflow of the remaining byte count while walking the list. Use the minimum of the scatterlist element size and the remaining byte count specified in the crypto request to avoid this. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Fix data alignment checksPatrick McHardy1-28/+14
The check for misalignment of the scatterlist data has two bugs: - the source buffer doesn't need to be aligned at all - the destination buffer and its size needs to be aligned to a multiple of 4, not to the crypto alg blocksize Introduce symbolic constant for destination buffer alignment requirements, use it instead of the crypto alg blocksize and remove the unnecessary checks for source buffer alignment and change cra_alignmask to zero. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Handle ablkcipher_walk errorsPatrick McHardy1-1/+4
ablkcipher_walk may return a negative error value, handle this properly instead of treating it as a huge number of scatter-gather elements. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Indicate asynchronous processing to crypto APIPatrick McHardy1-2/+2
hifn_setup_crypto() needs to return -EINPROGRESS on success to indicate asynchronous processing to the crypto API. This also means it must not return the errno code returned by hifn_process_queue(), if any. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Remove printk_ratelimit() for debugging printkPatrick McHardy1-1/+1
Without debugging this spams the log with "printk: N messages surpressed" without any actual messages on error. With debugging its more useful to always see the message. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-10[HIFN]: Endianess fixesPatrick McHardy1-30/+30
HIFN uses little-endian by default, move cpu_to_le32 conversion to hifn_write_0/ hifn_write_1, add sparse annotations and fix an invalid endian conversion in hifn_setup_src_desc. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-07-09Merge branch 'for-linus' of ↵Linus Torvalds1-0/+4
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: RDMA/cxgb3: Fix regression caused by class_device -> device conversion
2008-07-08RDMA/cxgb3: Fix regression caused by class_device -> device conversionSteve Wise1-0/+4
The change to iwch_provider.c in commit f4e91eb4 ("IB: convert struct class_device to struct device") undid the fix done in commit 7f049f2f ("RDMA/cxgb3: Hold rtnl_lock() around ethtool get_drvinfo call"). It removed the calls to rtnl_lock() that serialized the iw_cxgb3 ethtool ops calls into the cxgb3 driver. This locking is needed to avoid messing up the internal state of the cxgb3 driver. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-08Fix broken fix for fsl-diu-dbTakashi Iwai1-2/+2
On 2.6.26-rc9, the commit 05946bce839b4fed5442dbfab77060fb75e051f3 ("fsl_diu_fb: fix build with CONFIG_PM=y, plus fix some warnings") breaks its previous fix f969c5672b16b857e5231ad3c78f08d8ef3305aa ("fsl-diu-db: compile fix") This patch reverts the broken part. Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-08it8213: fix return value in it8213_init_one()Bartlomiej Zolnierkiewicz1-2/+1
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-08palm_bk3710: fix IDECLK period calculationSergei Shtylyov1-20/+18
The driver uses completely bogus rounding formula for calculating period from the IDECLK frequency which gives one-off period values (e.g. 11 ns with 100 MHz IDECLK) which in turn can lead to overclocked IDE transfer timings. Actually, rounding is just wrong in this case, so use a mere division for a safe result. While at it, also: - give 'ide_palm_clk' variable a more suitable name; - get rid of the useless 'ideclkp' variable; - drop the LISP stype 'p' postfix from the 'clkp' variable's name. :-) Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: mcherkashin@ru.mvista.com Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-08ide: add __ide_default_irq() inline helperBartlomiej Zolnierkiewicz2-11/+3
Add __ide_default_irq() inline helper and use it instead of ide_default_irq() in ide-probe.c and ns87415.c (all host drivers except IDE PCI ones always setup hwif->irq so it is enough to check only for I/O bases 0x1f0 and 0x170). This fixes post-2.6.25 regression since ide_default_irq() define could shadow ide_default_irq() inline. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds12-27/+71
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: can: add sanity checks fs_enet: restore promiscuous and multicast settings in restart() ibm_newemac: Fixes entry of short packets ibm_newemac: Fixes kernel crashes when speed of cable connected changes pasemi_mac: Access iph->tot_len with correct endianness ehea: Access iph->tot_len with correct endianness ehea: fix race condition ehea: add MODULE_DEVICE_TABLE ehea: fix might sleep problem forcedeth: fix lockdep warning on ethtool -s Add missing skb->dev assignment in Frame Relay RX code bridge: fix use-after-free in br_cleanup_bridges() tcp: fix a size_t < 0 comparison in tcp_read_sock tcp: net/ipv4/tcp.c needs linux/scatterlist.h libertas: support USB persistence on suspend/resume (resend) iwlwifi: drop skb silently for Tx request in monitor mode iwlwifi: fix incorrect 5GHz rates reported in monitor mode
2008-07-06pxamci: fix byte aligned DMA transfersPhilipp Zabel1-0/+13
The pxa27x DMA controller defaults to 64-bit alignment. This caused the SCR reads to fail (and, depending on card type, error out) when card->raw_scr was not aligned on a 8-byte boundary. For performance reasons all scatter-gather addresses passed to pxamci_request should be aligned on 8-byte boundaries, but if this can't be guaranteed, byte aligned DMA transfers in the have to be enabled in the controller to get correct behaviour. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-06Revert "USB: don't explicitly reenable root-hub status interrupts"Linus Torvalds22-31/+70
This reverts commit e872154921a6b5256a3c412dd69158ac0b135176. Andrey Borzenkov reports that it resulted in a totally hung machine for him when loading the OHCI driver. Extensive netconsole capture with SysRq output shows that modprobe gets stuck in ohci_hub_status_data() when probing and enabling the OHCI controller, see for example http://lkml.org/lkml/2008/7/5/236 for an analysis. The problem appears to be an interrupt flood triggered by the commit that gets reverted, and Andrey confirmed that the revert makes things work for him again. Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <david-b@pacbell.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-05Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds1-3/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86 ACPI: fix resume from suspend to RAM on uniprocessor x86-64 x86 ACPI: normalize segment descriptor register on resume
2008-07-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds2-18/+8
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: ide: ide_unregister() locking bugfix ide: ide_unregister() warm-plug bugfix ide: fix hwif->gendev refcounting
2008-07-05ahci: give another shot at clearing all bits in irq_statTejun Heo1-3/+13
Commit ea0c62f7cf70f13a67830471b613337bd0c9a62e tried to clear all bits in irq_stat but it didn't actually achieve that as irq_stat was anded with port_map right after read. This patch makes ahci driver always use the unmasked value to clear irq_status. While at it, add explanation on the peculiarities of ahci IRQ clearing. This was spotted by Linus Torvalds. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-05ide: ide_unregister() locking bugfixBartlomiej Zolnierkiewicz1-2/+2
Holding ide_lock for ide_release_dma_engine() call is unnecessary and triggers WARN_ON(irqs_disabled()) in dma_free_coherent(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-05ide: ide_unregister() warm-plug bugfixBartlomiej Zolnierkiewicz1-6/+6
Fix ide_unregister() to work for ports with no devices attached to them. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-05ide: fix hwif->gendev refcountingBartlomiej Zolnierkiewicz2-10/+0
class->dev_release is called by device_release() iff dev->release is not present so ide_port_class_release() is never called and the last hwif->gendev reference is not dropped. Fix it by removing ide_port_class_release() and get_device() call from ide_register_port() (device_create_drvdata() takes a hwif->gendev reference anyway). This patch fixes hang on wait_for_completion(&hwif->gendev_rel_comp) in ide_unregister() reported by Pavel Machek. Cc: Pavel Machek <pavel@suse.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Greg KH <greg@kroah.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-07-05x86 ACPI: normalize segment descriptor register on resumeH. Peter Anvin1-3/+2
Some Dell laptops enter resume with apparent garbage in the segment descriptor registers (almost certainly the result of a botched transition from protected to real mode.) The only way to clean that up is to enter protected mode ourselves and clean out the descriptor registers. This fixes resume on Dell XPS M1210 and Dell D620. Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10927 Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: pm list <linux-pm@lists.linux-foundation.org> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Tested-by: Kirill A. Shutemov <kirill@shutemov.name> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-04mmc: don't use DMA on newer ENE controllersPierre Ossman1-2/+4
Even the newer ENE controllers have bugs in their DMA engine that make it too dangerous to use. Disable it until someone has figured out under which conditions it corrupts data. This has caused problems at least once, and can be found as bug report 10925 in the kernel bugzilla. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04mm: switch node meminfo Active & Inactive pages to KbytesJohn Blackwood1-2/+2
There is a bug in the output of /sys/devices/system/node/node[n]/meminfo where the Active and Inactive values are in pages instead of Kbytes. Looks like this occurred back in 2.6.20 when the code was changed over to use node_page_state(). Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04olpc: sdhci: add quirk for the Marvell CaFe's interrupt timeoutAndres Salomon1-1/+11
The CaFe chip has a hardware bug that ends up with us getting a timeout value that's too small, causing the following sorts of problems: [ 60.525138] mmcblk0: error -110 transferring data [ 60.531477] end_request: I/O error, dev mmcblk0, sector 1484353 [ 60.533371] Buffer I/O error on device mmcblk0p2, logical block 181632 [ 60.533371] lost page write due to I/O error on mmcblk0p2 Presumably this is an off-by-one error in the hardware. Incrementing the timeout count value that we stuff into the TIMEOUT_CONTROL register gets us a value that works. This bug was originally discovered by Pierre Ossman, I believe. [thanks to Robert Millan for proving that this was still a problem] Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Pierre Ossman <drzeus-list@drzeus.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04olpc: sdhci: add quirk for the Marvell CaFe's vdd/powerup issueAndres Salomon1-0/+18
This has been sitting around unloved for way too long.. The Marvell CaFe chip's SD implementation chokes during card insertion if one attempts to set the voltage and power up in the same SDHCI_POWER_CONTROL register write. This adds a quirk that does that particular dance in two steps. It also adds an entry to pci_ids.h for the CaFe chip's SD device. Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Pierre Ossman <drzeus-list@drzeus.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04cciss: read config to obtain max outstanding commands per controllerMike Miller1-29/+37
This patch changes the way we determine the maximum number of outstanding commands for each controller. Most Smart Array controllers can support up to 1024 commands, the notable exceptions are the E200 and E200i. The next generation of controllers which were just added support a mode of operation called Zero Memory Raid (ZMR). In this mode they only support 64 outstanding commands. In Full Function Raid (FFR) mode they support 1024. We have been setting the queue depth by arbitrarily assigning some value for each controller. We needed a better way to set the queue depth to avoid lots of annoying "fifo full" messages. So we made the driver a little smarter. We now read the config table and subtract 4 from the returned value. The -4 is to allow some room for ioctl calls which are not tracked the same way as io commands are tracked. Please consider this for inclusion. Signed-off-by: Mike Miller <mike.miller@hp.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04spi: fix the read path in spidevSebastian Siewior1-6/+4
This got broken by the recent "fix rmmod $spi_driver while spidev-user is active". I tested the rmmod & write path but didn't check the read path. I am sorry. The read logic changed and spidev_sync_read() + spidev_sync_write() do not return zero on success anymore but the number of bytes that has been transfered over the bus. This patch changes the logic and copy_to_user() gets called again. The write path returns the number of bytes which are written to the underlying device what may be less than the requested size. This patch makes the same change to the read path or else we request a read of 20 bytes, get 10, don't call copy to user and report to the user that we read 10 bytes. [akpm@linux-foundation.org: remove test of known-to-be-zero local] Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04w100fb: add 80 MHz modelinePhilipp Zabel1-0/+1
This is needed for HTC Blueangel (w3200). At 96MHz its screen flickers. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <spyro@f2s.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04w100fb: do not depend on SHARPSLPhilipp Zabel1-1/+2
Apart from Sharp SL-Cxx series, there are a few other devices that have ATI Imageon chips, among them HP iPAQ hx4700. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <spyro@f2s.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04hdaps: add support for various newer Lenovo thinkpadsmaximilian attems1-0/+6
Adds R61, T61p, X61s, X61, Z61m, Z61p models to whitelist. Fixes this: cullen@lenny:~$ sudo modprobe hdaps FATAL: Error inserting hdaps (/lib/modules/2.6.22-10-generic/kernel/drivers/hwmon/hdaps.ko): No such device [25192.888000] hdaps: supported laptop not found! [25192.888000] hdaps: driver init failed (ret=-19)! Originally based on an Ubuntu patch that got it wrong, the dmidecode output of the corresponding laptops shows LENOVO as the manufacturer. https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/133636 tested on X61s: [ 184.893588] hdaps: inverting axis readings. [ 184.893588] hdaps: LENOVO ThinkPad X61s detected. [ 184.893588] input: hdaps as /class/input/input12 [ 184.924326] hdaps: driver successfully loaded. Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org> Cc: Chuck Short <zulcss@ubuntu.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: maximilian attems <max@stro.at> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04cciss: fix regression that no device nodes are created if no logical drives ↵Stephen M. Cameron1-0/+4
are configured. Fix regression in cciss driver that if no logical drives are configured, no device nodes at all get created. Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net> Acked-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04fsl_diu_fb: fix build with CONFIG_PM=y, plus fix some warningsAnton Vorontsov1-14/+15
This patch fixes following build error when CONFIG_PM is set. CC drivers/video/fsl-diu-fb.o drivers/video/fsl-diu-fb.c: In function 'fsl_diu_suspend': drivers/video/fsl-diu-fb.c:1327: error: 'ofdev' undeclared (first use in this function) drivers/video/fsl-diu-fb.c:1327: error: (Each undeclared identifier is reported only once drivers/video/fsl-diu-fb.c:1327: error: for each function it appears in.) drivers/video/fsl-diu-fb.c: In function 'fsl_diu_resume': drivers/video/fsl-diu-fb.c:1337: error: 'ofdev' undeclared (first use in this function) While I'm at it, also fix this warning: drivers/video/fsl-diu-fb.c: In function 'fsl_diu_alloc': drivers/video/fsl-diu-fb.c:314: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'phys_addr_t' And these section mismatches: ..from the function fsl_diu_remove() to the function .exit.text:uninstall_fb() ..from the function fsl_diu_remove() to the function .exit.text:uninstall_fb() ..from the function install_fb() to the variable .devinit.data:fsl_diu_mode_db ..from the function install_fb() to the variable .devinit.data:fsl_diu_mode_db ..from the function fsl_diu_probe() to the function .exit.text:uninstall_fb() ..from the function fsl_diu_probe() to the function .exit.text:uninstall_fb() Also, some sparse fixes: make two functions static, and use NULL where appropriate. There are still a lot of sparse warnings, mainly wrt absence of __iomem annotations, but some will require ugly __force stuff. I'll leave them for now, since proper fix would be not that trivial as few one-liners below. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Timur Tabi <timur@freescale.com> Cc: Antonino Daplas <adaplas@gmail.com> Cc: York Sun <yorksun@freescale.com> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04gpio: pca953x (i2c) handles max7310 tooDavid Brownell2-5/+11
The pca953x driver can handle another 8-bit I/O expander, the max7310. This patch adds that chip to the list of supported IDs in that driver, and expands the Kconfig helptext accordingly. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04Miguel Ojeda has movedMiguel Ojeda4-7/+7
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04pci: VT3336 can't do MSI eitherTejun Heo1-0/+1
It seems VT3336 can't do msi either as with its bro 3351. Disable it. Reported in the following SUSE bug. https://bugzilla.novell.com/show_bug.cgi?id=300001 Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04rtc: fix CMOS time error after writing /proc/acpi/alarmHuacai Chen1-1/+4
When writing /proc/acpi/alarm in adjust mode, e.g. echo "+0000-00-00 00:00:15" >/proc/acpi/alarm The "century" field should be read and added to "year" field before writing, otherwise the CMOS time will go back to 2000 years ago, e.g. # cat /proc/acpi/alarm 0008-06-21 11:38:46 Then the system time may be reset to the date of manufacture after rebooting. This patch fixed this issue. Signed-off-by: Huacai Chen <huacai.chen@intel.com> Acked-by: Pavel Machek <pavel@suse.cz> Acked-by: Zhao Yakui <yakui.zhao@intel.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Acked-by: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04rtc-x1205: Fix alarm setMichael Hamel1-20/+91
I have discovered that the current version of rtc-x1205.c does not work correctly when asked to set the alarm time by the RTC_WKALM_SET ioctl() call. This happens because the alarm registers do not behave like the current-time registers. They are non-volatile. Two things go wrong: - the X1205 requires a 10 msec delay after any attempt to write to the non-volatile registers. The x1205_set_datetime() routine does the write as 8 single-byte writes without any delay. Only the first write succeeds. The second is NAKed because the chip is busy. - the X1205 resets the RWEL bit after any write to the non-volatile registers. This would lock out any further writes after the first even with a 10msec delay. I fix this by doing a single 8-byte write and then waiting 10msec for the chip to be ready. A side effect of this change is that it will speed up x1205_rtc_set_time() which uses the same code. I have also implemented the 'enable' bit in the rtc_wkalm structure, which the existing driver does not attempt to do. I have modified both x1205_rtc_set_alarm() to set the AL0E bit, and x1205_rtc_read_alarm() to return it. I have tested this patch on a LinkSys NSLU2 under OpenWRT, but on no other hardware. On the NSLU2 the X1205 correctly asserts its IRQ pin when the alarm time matches the current time. [akpm@linux-foundation.org: clean up over-parenthesisation] Signed-off-by: Michael Hamel <mhamel@adi.co.nz> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04serial: fix serial_match_port() for dynamic major tty-device numbersGuennadi Liakhovetski1-1/+3
As reported by Vipul Gandhi, the current serial_match_port() doesn't work for tty-devices using dynamic major number allocation. Fix it. It oopses if you suspend a serial port with _dynamic_ major number. ATM, I think, there's only the drivers/serial/jsm/jsm_driver.c driver, that does it in-tree. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Vipul Gandhi <vcgandhi1@aol.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04rtc: rtc_read_alarm() handles wraparoundDavid Brownell1-11/+91
While 0e36a9a4a788e4e92407774df76c545910810d35 ("rtc: fix readback from /sys/class/rtc/rtc?/wakealarm") made sure that active alarms were never returned with invalid "wildcard" fields (negative), it can still report (wrongly) that the alarm triggers in the past. Example, if it's now 10am, an alarm firing at 5am will be triggered TOMORROW not today. (Which may also be next month or next year...) This updates that alarm handling in three ways: * Handle alarm rollover in the common cases of RTCs that don't support matching on all date fields. * Skip the invalid-field logic when it's not needed. * Minor bugfix ... tm_isdst should be ignored, it's one of the fields Linux doesn't maintain. A warning is emitted for some of the unhandled rollover cases, but the possible combinations are a bit too numerous to handle every bit of potential hardware and firmware braindamage. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Mark Lord <lkml@rtr.ca> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-04Merge branch 'upstream-linus' of ↵Linus Torvalds5-16/+27
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_mv: safer logic for limit_warnings libata-sff: improve HSM violation reporting ahci: always clear all bits in irq_stat sata_sil24: add DID for another adaptec flavor sata_uli: hardreset is broken
2008-07-04sata_mv: safer logic for limit_warningsMark Lord1-1/+1
There is a miniscule chance that two separate host controllers might be in sata_mv at the same time and manage to decrement the static limit_warnings variable below zero. Fix the comparison to deal with it. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04libata-sff: improve HSM violation reportingTejun Heo1-9/+21
Improve SFF HSM violation reporting such that each HSM violation can be distinguished using ehi_desc. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04ahci: always clear all bits in irq_statTejun Heo1-6/+3
Some AHCI controllers (ICH7 was reported) set pending bit in HOST_IRQ_STAT for non-existent ports and when it's not cleared falls into IRQ storm. Always clear full irq_stat instead of only the bits that are handled. As nothing changes for recognized ports, the risk of breaking things is pretty low. Reported and verified by Philipp Thomas in the following suse bugzilla. https://bugzilla.novell.com/attachment.cgi?id=215692 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Philipp Thomas <pth@novell.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04sata_sil24: add DID for another adaptec flavorTejun Heo1-0/+1
There's another DID used for Adaptec card. Add it. Reported by Travis Read. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Travis Read <ics@dark.net.au> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 03:52:00 +0000