| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-doc
|
|
Check if GPIO pin is valid by API helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
|
|
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq/timer fixes from Thomas Gleixner:
"irq: a fix for the new hierarchical MSI interrupt handling which
unbreaks PCI=n configurations.
timers: a fix for the new hrtimer clock offset update mechanism to
ensure that the boot time offset is respected"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Increment clock_was_set_seq in timekeeping_init()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
|
|
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
|
|
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
|
|
Commit 6afdb859b710 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit aa4d86163e4 ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Propagate the actual return code of __spi_validate_bits_per_word() in
spi_setup().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Reflects ceph.git commit 7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Commit 30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
* acpica:
ACPICA: Tables: Fix FADT dependency regression
* pm-domains:
PM / Domains: Fix validation of latency constraints in genpd governor
* pm-cpufreq:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
|
|
When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS
is set, and that any of .mask or .unmask are NULL in the irq_chip
structure, we set them to pci_msi_[un]mask_irq.
This is a bad idea for at least two reasons:
- PCI_MSI might not be selected, kernel fails to build (yes, this is
legitimate, at least on arm64!)
- This may not be a PCI/MSI domain at all (platform MSI, for example)
Either way, this looks wrong. Move the overriding of mask/unmask to
the PCI counterpart, and panic is any of these two methods is not
set in the core code (they really should be present).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1444760085-27857-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The virtgpu driver prints the last_seq variable using the %ld or
%lu format string, which does not work correctly on all architectures
and causes this compiler warning on ARM:
drivers/gpu/drm/virtio/virtgpu_fence.c: In function 'virtio_timeline_value_str':
drivers/gpu/drm/virtio/virtgpu_fence.c:64:22: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'long long int' [-Wformat=]
snprintf(str, size, "%lu", atomic64_read(&fence->drv->last_seq));
^
drivers/gpu/drm/virtio/virtgpu_debugfs.c: In function 'virtio_gpu_debugfs_irq_info':
drivers/gpu/drm/virtio/virtgpu_debugfs.c:37:16: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'long long int' [-Wformat=]
seq_printf(m, "fence %ld %lld\n",
^
In order to avoid the warnings, this changes the format strings to %llu
and adds a cast to u64, which makes it work the same way everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
into drm-fixes
Just two fixes for amdgpu:
- fix pageflip interrupt issue
- fix display clock handling on certain fiji boards
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2015-10-14
* tag 'vmwgfx-fixes-4.3-151014' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are some overdue (what can I say, I was on a short vacation)
driver fixes for the pin control subsystem:
- Allwinner sun5i A10s had a faulty mapping
- Freescale i.MX25 had some bad arithmetics
- Uniphier PH1-sLD8 missed some input enable settings"
* tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix input enable settings for PH1-sLD8
pinctrl: imx25: ensure that a pin with id i is at position i in the info array
pinctrl: sun5i: Fix a10s pwm1 pinctrl mapping
|
|
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"We have four batched up patches for the current rc kernel.
Two of them are small fixes that are obvious.
One of them is larger than I would like for a late stage rc pull, but
we found an issue in the namespace lookup code related to RoCE and
this works around the issue for now (we allow a lookup with a
namespace to succeed on RoCE since RoCE namespaces aren't implemented
yet). This will go away in 4.4 when we put in support for namespaces
in RoCE devices.
The last one is large in terms of lines, but is all legal and no
functional changes. Cisco needed to update their files to be more
specific about their license. They had intended the files to be dual
licensed as GPL/BSD all along, and specified that in their module
license tag, but their file headers were not up to par. They
contacted all of the contributors to get agreement and then submitted
a patch to update the license headers in the files.
Summary:
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: For sendonly join free the multicast group on leave
IB/cma: Accept connection without a valid netdev on RoCE
xprtrdma: Don't require LOCAL_DMA_LKEY support for fastreg
usnic: add missing clauses to BSD license
|
|
This fixes flickering issues caused by prematurely firing pflip
interrupts.
v2 (chk): add commit message, fix DCE V10/V11 and DM as well
v3: Re-enable pflip interrupt wherever we re-enable a CRTC
v4: Enable pflip interrupt in DAL as well
v5: drop DAL changes for upstream
v6: (agd): only enable interrupts on crtcs that exist
v7: (agd): integrate suggestions from Michel
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Set the default to 600Mhz if it's not set in the bios,
and bump the default to 600Mhz if it's lower than that.
Port of radeon commit:
9368931db826d57b6b88b3145a00276626b48df0
v2: clean up the code a bit
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91896
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@kernel.org
|
|
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
A change of return status was introduced in commit 3fffd1283927
("i2c: allow specifying separate wakeup interrupt in device tree")
The commit prevents the defer status being passed up the call stack
appropriately when dev_pm_domain_attach returns -EPROBE_DEFER.
Catch the PROBE_DEFER and clear up the IRQ wakeup status
Signed-off-by: Kieran Bingham <kieranbingham@gmail.com>
Fixes: 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree")
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This zeroes the msg so no random stack data ends up getting
sent, it also limits the function to not accepting > 4
i2c msgs.
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This allows tiled monitors to work with radeon once mst is enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some logics actually relying on the existence of FADT, currently relies on
the number of loaded tables. This false dependency can easily trigger
regressions. One of them has been introduced by commit 8ec3f459073e
(ACPICA: Tables: Fix global table list issues by removing fixed table).
The commit changing the fixed table indexes results in the change of FADT
table index, originally, it was 3 (thus the installed table count should be
greater than 4), while currently it is 0 (and the installed table count may
be 3).
This patch fixes this regression by cleaning up the code. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=105351
Fixes: 8ec3f459073e (ACPICA: Tables: Fix global table list issues by removing fixed table)
Reported-and-tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This partially reverts commit eca61c9ff2588e1df373e61078e1874976315839.
Thomas reports that it causes regressions on Armada XP devices.
This is because of_clk_get_parent_name() relies on the property
'clock-output-names' to resolve the name of a clock's parent,
without trying to get the clock from the framework and call
__clk_get_name(). Given that Armada XP devices don't have the
'clock-output-names' property, of_clk_get_parent_name() returns
the name of the node which doesn't match the actual parent
clock's name at all, causing CPU clocks to never link up with
their parents.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Bug Fixes:
- Return correct error code i.e. not zero
- Fix build error when !CONFIG_PM_SLEEP"
* tag 'mfd-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: max77843: Fix max77843_chg_init() return on error
mfd: intel-lpss: Fix build error when !CONFIG_PM_SLEEP
|
|
Fix the copy paste error on the electrodes_rx value set code which will
cause the electrodes_rx value be always set to the value of electrodes_y.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit ba2bbfbf6307 (PM / Domains: Remove intermediate states from the
power off sequence) changed the power off sequence in genpd. That also
required some updates regarding the validation of latency constraints in
the genpd governor. Unfortunate that wasn't covered, so let's fix this.
From a runtime PM and latency point of view, we need to consider the worst
case scenario while validating latency constraints. That's typically when
a call to pm_runtime_get_sync() needs to wait for a ongoing runtime
suspend operation to be carried out, as it then also needs to wait for the
device to be runtime resumed again.
The above mentioned commit made the genpd governor's ->stop_ok() callback
responsible of validating genpd's device's runtime suspend/resume latency.
In other words, the constraint needs to be validated towards the relevant
latencies present in genpd's ->runtime_suspend|resume() callbacks.
Earlier, that included latencies from the ->stop|start() callbacks, but as
->save|restore_state() are now also being invoked from genpd's
->runtime_suspend|resume() and to comply with the worst case scenario,
let's take also those latencies into account.
Fixes: ba2bbfbf6307 (PM / Domains: Remove intermediate states from the power off sequence)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When we leave the multicast group on expiration of a neighbor we
do not free the mcast structure. This results in a memory leak
that causes ib_dealloc_pd to fail and print a WARN_ON message
and backtrace.
Fixes: bd99b2e05c4d (IB/ipoib: Expire sendonly multicast joins)
Signed-off-by: Christoph Lameter <cl@linux.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few fixes piled up:
- Fix for a suspend/resume issue where PCI probing code overwrote
dev->irq for the MSI irq of the AMD IOMMU.
- Fix for a kernel crash when a 32 bit PCI device was assigned to a
KVM guest.
- Fix for a possible memory leak in the VT-d driver
- A couple of fixes for the ARM-SMMU driver"
* tag 'iommu-fixes-v4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix NULL pointer deref on device detach
iommu/amd: Prevent binding other PCI drivers to IOMMU PCI devices
iommu/vt-d: Fix memory leak in dmar_insert_one_dev_info()
iommu/arm-smmu: Use correct address mask for CMD_TLBI_S2_IPA
iommu/arm-smmu: Ensure IAS is set correctly for AArch32-capable SMMUs
iommu/io-pgtable-arm: Don't use dma_to_phys()
|
|
Pull drm fixes from Dave Airlie:
"I got a bit behind last week, so here is a delayed fixes pull:
- a bunch of radeon/amd gpu fixes
- some nouveau regression fixes (ppc bios reading and runtime pm fix)
- one drm core oops fix
- two qxl locking fixes
- one qxl regression fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/bios: fix OF loading
drm/nouveau/fbcon: take runpm reference when userspace has an open fd
drm/nouveau/nouveau: Disable AGP for SiS 761
drm/nouveau/display: allow up to 16k width/height for fermi+
drm/nouveau/bios: translate devinit pri/sec i2c bus to internal identifiers
drm: Fix locking for sysfs dpms file
drm/amdgpu: fix memory leak in amdgpu_vm_update_page_directory
drm/amdgpu: fix 32-bit compiler warning
drm/qxl: avoid dependency lock
drm/qxl: avoid buffer reservation in qxl_crtc_page_flip
drm/qxl: fix framebuffer dirty rectangle tracking.
drm/amdgpu: flag iceland as experimental
drm/amdgpu: check before checking pci bridge registers
drm/amdgpu: fix num_crtc on CZ
drm/amdgpu: restore the fbdev mode in lastclose
drm/radeon: restore the fbdev mode in lastclose
drm/radeon: add quirk for ASUS R7 370
drm/amdgpu: add pm sysfs files late
drm/radeon: add pm sysfs files late
|
|
Fixes: ac8c3f3df ("dm thin: generate event when metadata threshold passed")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.10+
|
|
If an unsupported option is given then the early return from
persistent_ctr() leaked memory allocated for the 'pstore' and never
destroyed the 'metadata_wq'.
Fixes: b0d3cc011e53 ("dm snapshot: add new persistent store option to support overflow")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The commit "drm/vmwgfx: Fix up user_dmabuf refcounting", while fixing a
kernel crash introduced a NULL pointer dereference on older hardware.
Fix this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
|
|
Currently the IRQs for SPI client devices, registered via device-tree,
are mapped when the client devices are registered. If the corresponding
irq-chip has not been probed yet, then the probing of the client device
will fail and will not be retried. Resolve this by mapping the IRQ at
probe time and allow the probe to be deferred if the IRQ is not yet
available.
If of_irq_get() returns an error that is not -EPROBE_DEFER, then assume
that the SPI client does not have an IRQ and set the IRQ number to zero
(which is equivalent to irq_of_parse_and_map()).
This is based on some inputs from Thierry Reding <treding@nvidia.com>.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
Nothing too crazy here, a couple of regression fixes + runpm/fbcon
race fix.
* 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix OF loading
drm/nouveau/fbcon: take runpm reference when userspace has an open fd
drm/nouveau/nouveau: Disable AGP for SiS 761
drm/nouveau/display: allow up to 16k width/height for fermi+
drm/nouveau/bios: translate devinit pri/sec i2c bus to internal identifiers
|
|
Currently OF bios load fails for a few reasons:
- checksum failure
- bios size too small
- no PCIR header
- bios length not a multiple of 4
In this change, we resolve all of the above by ignoring any checksum
failures (since OF VBIOS tends not to have a checksum), and faking the
PCIR data when loading from OF.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
We need to do this in order to prevent accesses to the device while it's
powered down. Userspace may have an mmap of the fb, and there's no good
way (that I know of) to prevent it from touching the device otherwise.
This fixes some nasty races between runpm and plymouth on some systems,
which result in the GPU getting very upset and hanging the boot.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
SiS 761 chipset does not support AGP cards but has AGP capability (for
the onboard video). At least PC Chips A31G board using this chipset has
an AGP-like AGPro slot that's wired to the PCI bus. Enabling AGP will
fail (GPU lockup and software fbcon, X11 hangs).
Add support for matching just the host bridge in nvkm_device_agp_quirks
and add entry for SiS 761 with mode 0 (AGP disabled).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
