| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- revert of a commit that switched all Synaptics touchpads over to be
driven by hid-rmi. It turns out that this caused several user-visible
regressions, and therefore we revert back to the original state
before all the reported issues have been fixed.
- a new uclogic device ID addition, from Xiaolei Yu.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: rmi: Handle all Synaptics touchpads using hid-rmi"
HID: uclogic: add support for Ugee Tablet EX07S
|
|
On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.
This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program. Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.
# sg_dd if=/dev/dm-2 bs=4096 count=1 dio=1 verbose=4 blk_sgio=0
<...>
read(unix): count=4096, res=-1
sg_dd: reading, skip=0 : Input/output error
<...>
# dmesg
[...] sd 2:2:16:0: [sds] FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[...] sd 2:2:16:0: [sds] Sense Key : Medium Error [current]
[...] sd 2:2:16:0: [sds] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] sd 2:2:16:0: [sds] CDB: Read(10) 28 00 00 00 00 00 00 00 20 00
[...] blk_update_request: I/O error, dev sds, sector 0
[...] device-mapper: multipath: Failing path 65:32.
<...>
[...] device-mapper: multipath: Failing path 65:224.
# multipath -l
1IBM_IPR-0_59C2AE0000001F80 dm-2 IBM ,IPR-0 59C2AE00
size=5.2T features='0' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=enabled
| `- 2:2:16:0 sds 65:32 failed undef running
`-+- policy='service-time 0' prio=0 status=enabled
`- 1:2:7:0 sdae 65:224 failed undef running
This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().
The problem trace is:
1) ipr_scsi_done() // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start() // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense() // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
// so set DID_PASSTHROUGH.
4) scsi_decide_disposition() // check for DID_PASSTHROUGH and return
// early on, faking a DID_OK.. *instead*
// of reaching scsi_check_sense().
// Had it reached the latter, that would
// set host_byte to DID_MEDIUM_ERROR.
5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte() // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error() // And that is checked in dm-mpath :: noretry_error()
// which would cause fail_path() not to be called.
With this patch applied, the I/O is failed but the paths are not. This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).
# dmesg
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] Buffer I/O error on dev dm-6, logical block 0, async page read
# multipath -l 1IBM_IPR-0_59C2AE0000001F80
1IBM_IPR-0_59C2AE0000001F80 dm-6 IBM ,IPR-0 59C2AE00
size=5.2T features='1 queue_if_no_path' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| `- 2:2:7:0 sdaf 65:240 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
`- 1:2:7:0 sdh 8:112 active undef running
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.
This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.
Fixes: 5c63f7f710bd ("aacraid: Added EEH support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On SPARC, the udl driver filled my kernel log with these messages:
[186668.910612] Kernel unaligned access at TPC[76609c] udl_render_hline+0x13c/0x3a0
Use put_unaligned_be16 to avoid them. On x86 this results in the same
code, but on SPARC the compiler emits two single-byte stores.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407200229.20642-1-j.neuschaefer@gmx.net
|
|
Only call synchronize_rcu_expedited after unlocking struct_mutex to
avoid deadlock because the workqueues depend on struct_mutex.
>From original patch by Andrea:
synchronize_rcu/synchronize_sched/synchronize_rcu_expedited() will
hang until its own workqueues are run. The i915 gem workqueues will
wait on the struct_mutex to be released. So we cannot wait for a
quiescent state using those rcu primitives while holding the
struct_mutex or it creates a circular lock dependency resulting in
kernel hangs (which is reproducible but goes undetected by lockdep).
kswapd0 D 0 700 2 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? _synchronize_rcu_expedited.constprop.65+0x2ef/0x300
? wake_up_bit+0x20/0x20
? rcu_stall_kick_kthreads.part.54+0xc0/0xc0
? rcu_exp_wait_wake+0x530/0x530
? i915_gem_shrink+0x34b/0x4b0
? i915_gem_shrinker_scan+0x7c/0x90
? i915_gem_shrinker_scan+0x7c/0x90
? shrink_slab.part.61.constprop.72+0x1c1/0x3a0
? shrink_zone+0x154/0x160
? kswapd+0x40a/0x720
? kthread+0xf4/0x130
? try_to_free_pages+0x450/0x450
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
plasmashell D 0 4657 4614 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? i915_gem_close_object+0x26/0xc0
? i915_gem_close_object+0x26/0xc0
? drm_gem_object_release_handle+0x48/0x90
? drm_gem_handle_delete+0x50/0x80
? drm_ioctl+0x1fa/0x420
? drm_gem_handle_create+0x40/0x40
? pipe_write+0x391/0x410
? __vfs_write+0xc6/0x120
? do_vfs_ioctl+0x8b/0x5d0
? SyS_ioctl+0x3b/0x70
? entry_SYSCALL_64_fastpath+0x13/0x94
kworker/0:0 D 0 29186 2 0x00000000
Workqueue: events __i915_gem_free_work
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? del_timer_sync+0x44/0x50
? update_curr+0x57/0x110
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_work+0x2d/0x40
? process_one_work+0x13a/0x3b0
? worker_thread+0x4a/0x460
? kthread+0xf4/0x130
? process_one_work+0x3b0/0x3b0
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
Fixes: 3d3d18f086cd ("drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)")
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 8f612d055183545070ca1009ac2eb1f2e044cc20)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
i915 is currently doing a full GPU reset at the end of
i915_gem_suspend() followed by GuC suspend in i915_drm_suspend(). This
GPU reset clobbers the GuC, causing the suspend request to then fail,
leaving the GuC in an undefined state. We need to tell the GuC to
suspend before we do the direct intel_gpu_reset().
v2: Commit message update. (Chris, Daniele)
Fixes: 1c777c5d1dcd ("drm/i915/hsw: Fix GPU hang during resume from S3-devices state")
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491387710-20553-1-git-send-email-sagar.a.kamble@intel.com
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit fd08923384385400101c71ac0d21d37d6b23b00d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
drm-intel-fixes
gvt-fixes-2017-04-07
- execlist csb initial read ptr fix (Min)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407084240.4d2ig5ja2umcnsq3@zhen-hp.sh.intel.com
|
|
This reverts commit 279967a65b320d174a507498aea7d44db3fee7f4.
Multiple regressions [1] [2] [3] have been reported. The hid-rmi
support would have to fixed and redone in 4.11+.
[1] http://lkml.kernel.org/r/b79b88c8-770a-13f6-5668-c3a94254e5e0@gmail.com
[2] http://lkml.kernel.org/r/375e67b5-2cb8-3491-1d71-d8650d6e9451@gmail.com
[3] https://bugzilla.kernel.org/show_bug.cgi?id=195287
Reported-by: Cameron Gutman <aicommander@gmail.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: Lorenzo J. Lucchini <ljlbox@tiscali.it>
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
After commit 47c950d10202 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.
However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.
Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d10202 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
As a minimal fix, disable error clearing when the BTT is enabled for the
namespace. For the final fix a larger rework of the poison list locking
is needed.
Note that this is not a problem in the blk case since that path never
calls nvdimm_clear_poison().
Cc: <stable@vger.kernel.org>
Fixes: 82bf1037f2ca ("libnvdimm: check and clear poison before writing to pmem")
Cc: Dave Jiang <dave.jiang@intel.com>
[jeff: dynamically disable error clearing in the btt case]
Suggested-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Holding the reconfig_mutex over a potential userspace fault sets up a
lockdep dependency chain between filesystem-DAX and the libnvdimm ioctl
path. Move the user access outside of the lock.
[ INFO: possible circular locking dependency detected ]
4.11.0-rc3+ #13 Tainted: G W O
-------------------------------------------------------
fallocate/16656 is trying to acquire lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffa00080b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
but task is already holding lock:
(jbd2_handle){++++..}, at: [<ffffffff813b4944>] start_this_handle+0x104/0x460
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (jbd2_handle){++++..}:
lock_acquire+0xbd/0x200
start_this_handle+0x16a/0x460
jbd2__journal_start+0xe9/0x2d0
__ext4_journal_start_sb+0x89/0x1c0
ext4_dirty_inode+0x32/0x70
__mark_inode_dirty+0x235/0x670
generic_update_time+0x87/0xd0
touch_atime+0xa9/0xd0
ext4_file_mmap+0x90/0xb0
mmap_region+0x370/0x5b0
do_mmap+0x415/0x4f0
vm_mmap_pgoff+0xd7/0x120
SyS_mmap_pgoff+0x1c5/0x290
SyS_mmap+0x22/0x30
entry_SYSCALL_64_fastpath+0x1f/0xc2
-> #1 (&mm->mmap_sem){++++++}:
lock_acquire+0xbd/0x200
__might_fault+0x70/0xa0
__nd_ioctl+0x683/0x720 [libnvdimm]
nvdimm_ioctl+0x8b/0xe0 [libnvdimm]
do_vfs_ioctl+0xa8/0x740
SyS_ioctl+0x79/0x90
do_syscall_64+0x6c/0x200
return_from_SYSCALL_64+0x0/0x7a
-> #0 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
__lock_acquire+0x16b6/0x1730
lock_acquire+0xbd/0x200
__mutex_lock+0x88/0x9b0
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
pmem_do_bvec+0x1c2/0x2b0 [nd_pmem]
pmem_make_request+0xf9/0x270 [nd_pmem]
generic_make_request+0x118/0x3b0
submit_bio+0x75/0x150
Cc: <stable@vger.kernel.org>
Fixes: 62232e45f4a2 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices")
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit 57e5568fda27 ("sata_via: Implement hotplug for VT6421") adds
hotplug IRQ handler for VT6421 but enables hotplug on all chips. This
is a bug because it causes "irq xx: nobody cared" error on VT6420 when
hot-(un)plugging a drive:
[ 381.839948] irq 20: nobody cared (try booting with the "irqpoll" option)
[ 381.840014] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc5+ #148
[ 381.840066] Hardware name: P4VM800/P4VM800, BIOS P1.60 05/29/2006
[ 381.840117] Call Trace:
[ 381.840167] <IRQ>
[ 381.840225] ? dump_stack+0x44/0x58
[ 381.840278] ? __report_bad_irq+0x14/0x97
[ 381.840327] ? handle_edge_irq+0xa5/0xa5
[ 381.840376] ? note_interrupt+0x155/0x1cf
[ 381.840426] ? handle_edge_irq+0xa5/0xa5
[ 381.840474] ? handle_irq_event_percpu+0x32/0x38
[ 381.840524] ? handle_irq_event+0x1f/0x38
[ 381.840573] ? handle_fasteoi_irq+0x69/0xb8
[ 381.840625] ? handle_irq+0x4f/0x5d
[ 381.840672] </IRQ>
[ 381.840726] ? do_IRQ+0x2e/0x8b
[ 381.840782] ? common_interrupt+0x2c/0x34
[ 381.840836] ? mwait_idle+0x60/0x82
[ 381.840892] ? arch_cpu_idle+0x6/0x7
[ 381.840949] ? do_idle+0x96/0x18e
[ 381.841002] ? cpu_startup_entry+0x16/0x1a
[ 381.841057] ? start_kernel+0x319/0x31c
[ 381.841111] ? startup_32_smp+0x166/0x168
[ 381.841165] handlers:
[ 381.841219] [<c12a7263>] ata_bmdma_interrupt
[ 381.841274] Disabling IRQ #20
Seems that VT6420 can do hotplug too (there's no documentation) but the
comments say that SCR register access (required for detecting hotplug
events) can cause problems on these chips.
For now, just keep hotplug disabled on anything other than VT6421.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
virtio-pci registers a per-vq affinity hint when using MSIX,
but fails to remove it when freeing the interrupt, resulting
in this type of splat:
[ 31.111202] WARNING: CPU: 0 PID: 2823 at kernel/irq/manage.c:1503 __free_irq+0x2c4/0x2c8
[ 31.114689] Modules linked in:
[ 31.116101] CPU: 0 PID: 2823 Comm: kexec Not tainted 4.10.0+ #6941
[ 31.118911] Hardware name: Generic DT based system
[ 31.121319] [<c022fb78>] (unwind_backtrace) from [<c0229d8c>] (show_stack+0x18/0x1c)
[ 31.125017] [<c0229d8c>] (show_stack) from [<c05192f4>] (dump_stack+0x84/0x98)
[ 31.128427] [<c05192f4>] (dump_stack) from [<c023d940>] (__warn+0xf4/0x10c)
[ 31.131910] [<c023d940>] (__warn) from [<c023da20>] (warn_slowpath_null+0x28/0x30)
[ 31.135543] [<c023da20>] (warn_slowpath_null) from [<c0290238>] (__free_irq+0x2c4/0x2c8)
[ 31.139355] [<c0290238>] (__free_irq) from [<c02902d0>] (free_irq+0x44/0x78)
[ 31.142909] [<c02902d0>] (free_irq) from [<c059d3a8>] (vp_del_vqs+0x68/0x1c0)
[ 31.146299] [<c059d3a8>] (vp_del_vqs) from [<c056ca4c>] (pci_device_shutdown+0x3c/0x78)
The obvious fix is to drop the affinity hint before freeing the
interrupt.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 5c34d002dcc7a6dd665a19d098b4f4cd5501ba1a.
Conflicts:
drivers/virtio/virtio_pci_common.c
The cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
This reverts the cleanup changes but keeps the affinity support.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 07ec51480b5eb1233f8c1b0f5d7a7c8d1247c507.
Conflicts:
drivers/virtio/virtio_pci_common.c
Unfortunately the idea does not work with threadirqs
as more than 32 queues can then map to a single interrupts.
Further, the cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
This reverts the cleanup changes but keeps the affinity support.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 53a020c661741f3b87ad3ac6fa545088aaebac9b.
The cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 52a61516125fa9a21b3bdf4f90928308e2e5573f.
Conflicts:
drivers/virtio/virtio_pci_common.c
The cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
This reverts the cleanup changes but keeps the affinity support.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit de85ec8b07f82c8c84de7687f769e74bf4c26a1e.
Follow-up patches will revert 07ec51480b5e ("virtio_pci: use shared
interrupts for virtqueues") that triggered the problem so no need for
this one anymore.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a number of bugs in the caam driver:
- device creation fails after release
- error-path NULL-pointer dereference
- spurious hardware error in RNG deinstantiation"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix RNG deinstantiation error checking
crypto: caam - fix invalid dereference in caam_rsa_init_tfm()
crypto: caam - fix JR platform device subsequent (re)creations
|
|
The commit 1259feddd0f8("pinctrl: samsung: Fix the width of
PINCFG_TYPE_DRV bitfields for Exynos5433") already fixed
the different width of PINCFG_TYPE_DRV from previous Exynos SoC.
However wrong merge conflict resolution was chosen in commit
7f36f5d11cda ("Merge tag 'v4.10-rc6' into devel") effectively dropping
the changes for PINCFG_TYPE_DRV. Re-do them here.
The macro EXYNOS_PIN_BANK_EINTW is no longer used so remove it.
Fixes: 7f36f5d11cda ("Merge tag 'v4.10-rc6' into devel")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
both our sqsize and the controller MQES cap are a 0 based value,
so making it 1 based is wrong.
Reported-by: Trapp, Darren <Darren.Trapp@cavium.com>
Reported-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
both our sqsize and the controller MQES cap are a 0 based value,
so making it 1 based is wrong.
Reported-by: Trapp, Darren <Darren.Trapp@cavium.com>
Reported-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
both our sqsize and the controller MQES cap are a 0 based value,
so making it 1 based is wrong.
Reported-by: Trapp, Darren <Darren.Trapp@cavium.com>
Reported-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver rfixes from Greg KH:
"Here are a number of small IIO and staging driver fixes for 4.11-rc6.
Nothing big here, just iio fixes for reported issues, and an ashmem
fix for a very old bug that has been reported by a number of Android
vendors"
* tag 'staging-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ashmem: lseek failed due to no FMODE_LSEEK.
iio: hid-sensor-attributes: Fix sensor property setting failure.
iio: accel: hid-sensor-accel-3d: Fix duplicate scan index error
iio: core: Fix IIO_VAL_FRACTIONAL_LOG2 for negative values
iio: st_pressure: initialize lps22hb bootime
iio: bmg160: reset chip when probing
iio: cros_ec_sensors: Fix return value to get raw and calibbias data.
|
|
Pull block fixes from Jens Axboe:
"Here's a pull request for 4.11-rc, fixing a set of issues mostly
centered around the new scheduling framework. These have been brewing
for a while, but split up into what we absolutely need in 4.11, and
what we can defer until 4.12. These are well tested, on both single
queue and multiqueue setups, and with and without shared tags. They
fix several hangs that have happened in testing.
This is obviously larger than I would have preferred at this point in
time, but I don't think we can shave much off this and still get the
desired results.
In detail, this pull request contains:
- a set of five fixes for NVMe, mostly from Christoph and one from
Roland.
- a series from Bart, fixing issues with dm-mq and SCSI shared tags
and scheduling. Note that one of those patches commit messages may
read like an optimization, but it is in fact an important fix for
queue restarts in particular.
- a series from Omar, most importantly fixing a hang with multiple
hardware queues when we fail to get a driver tag. Another important
fix in there is for resizing hardware queues, which nbd does when
handling multiple sockets for one connection.
- fixing an imbalance in putting the ctx for hctx request allocations
from Minchan"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: Restart a single queue if tag sets are shared
dm rq: Avoid that request processing stalls sporadically
scsi: Avoid that SCSI queues get stuck
blk-mq: Introduce blk_mq_delay_run_hw_queue()
blk-mq: remap queues when adding/removing hardware queues
blk-mq-sched: fix crash in switch error path
blk-mq-sched: set up scheduler tags when bringing up new queues
blk-mq-sched: refactor scheduler initialization
blk-mq: use the right hctx when getting a driver tag fails
nvmet: fix byte swap in nvmet_parse_io_cmd
nvmet: fix byte swap in nvmet_execute_write_zeroes
nvmet: add missing byte swap in nvmet_get_smart_log
nvme: add missing byte swap in nvme_setup_discard
nvme: Correct NVMF enum values to match NVMe-oF rev 1.0
block: do not put mq context in blk_mq_alloc_request_hctx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"This late fix for pin control is hopefully the last I send this cycle.
The problem was detected early in the v4.11 release cycle and there
has been some back and forth on how to solve it. Sadly the proper fix
arrives late, but at least not too late.
An issue was detected with pin control on the Freescale i.MX after the
refactorings for more general group and function handling.
We now have the proper fix for this"
* tag 'pinctrl-v4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-04-04
this is a pull request of two patches for net/master.
The first patch by Markus Marb fixes a register read access in the ifi driver.
The second patch by Geert Uytterhoeven for the rcar driver remove the printing
of a kernel virtual address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vfs_llseek will check whether the file mode has
FMODE_LSEEK, no return failure. But ashmem can be
lseek, so add FMODE_LSEEK to ashmem file.
Comment From Greg Hackmann:
ashmem_llseek() passes the llseek() call through to the backing
shmem file. 91360b02ab48 ("ashmem: use vfs_llseek()") changed
this from directly calling the file's llseek() op into a VFS
layer call. This also adds a check for the FMODE_LSEEK bit, so
without that bit ashmem_llseek() now always fails with -ESPIPE.
Fixes: 91360b02ab48 ("ashmem: use vfs_llseek()")
Signed-off-by: Shuxiao Zhang <zhangshuxiao@xiaomi.com>
Tested-by: Greg Hackmann <ghackmann@google.com>
Cc: stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
into fixes
Reset controller fixes for v4.11
Fix devm_reset_controller_get_optional to return NULL for non-DT devices,
if the RESET_CONTROLLER Kconfig option is enabled. This fixes probe failures
of the 8250_dw driver on Intel platforms after commit acbdad8dd1ab ("serial:
8250_dw: simplify optional reset handling").
* tag 'reset-fixes-for-4.11-2' of git://git.pengutronix.de/git/pza/linux:
reset: add exported __reset_control_get, return NULL if optional
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Cc: <stable@vger.kernel.org>
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.
Fixes: a465537ad1a4 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We need to initialize qedf->fipvlan_compl in __qedf_probe so that if we
receive an unsolicited FIP VLAN response, the system doesn't crash due
to trying to complete an uninitialized completion.
Also add a check to see if there are any waiters on the completion so we
don't inadvertantly kick start the discovery process due to the
unsolicited frame.
Fixed the crash:
<1>BUG: unable to handle kernel NULL pointer dereference at (null)
<1>IP: [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4>PGD 0
<4>Oops: 0000 [#1] SMP
<4>last sysfs file: /sys/devices/system/cpu/online
<4>CPU 7
<4>Modules linked in: autofs4 nfs lockd fscache auth_rpcgss nfs_acl sunrpc target_core_iblock target_core_file target_core_pscsi target_core_mod configfs bnx2fc cnic fcoe 8021q garp stp llc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 vfat fat uinput ipmi_devintf microcode power_meter acpi_ipmi ipmi_si ipmi_msghandler iTCO_wdt iTCO_vendor_support dcdbas sg joydev sb_edac edac_core lpc_ich mfd_core shpchp tg3 ptp pps_core ext4 jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif qedi(U) iscsi_boot_sysfs libiscsi scsi_transport_iscsi uio qedf(U) libfcoe libfc scsi_transport_fc scsi_tgt qede(U) qed(U) ahci megaraid_sas wmi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: speedstep_lib]
<4>
<4>Pid: 1485, comm: qedf_11_ll2 Not tainted 2.6.32-642.el6.x86_64 #1 Dell Inc. PowerEdge R730/0599V5
<4>RIP: 0010:[<ffffffff8105ed71>] [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4>RSP: 0018:ffff881068a83d50 EFLAGS: 00010086
<4>RAX: ffffffffffffffe8 RBX: ffff88106bf42de0 RCX: 0000000000000000
<4>RDX: 0000000000000000 RSI: 0000000000000003 RDI: ffff88106bf42de0
<4>RBP: ffff881068a83d90 R08: 0000000000000000 R09: 00000000fffffffe
<4>R10: 0000000000000000 R11: 000000000000000b R12: 0000000000000286
<4>R13: ffff88106bf42de8 R14: 0000000000000000 R15: 0000000000000000
<4>FS: 0000000000000000(0000) GS:ffff88089c460000(0000) knlGS:0000000000000000
<4>CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
<4>CR2: 0000000000000000 CR3: 0000000001a8d000 CR4: 00000000001407e0
<4>DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
<4>DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
<4>Process qedf_11_ll2 (pid: 1485, threadinfo ffff881068a80000, task ffff881068a70040)
<4>Stack:
<4> ffff88106ef00090 0000000300000001 ffff881068a83d90 ffff88106bf42de0
<4><d> 0000000000000286 ffff88106bf42dd8 ffff88106bf40a50 0000000000000002
<4><d> ffff881068a83dc0 ffffffff810634c7 ffff881000000003 000000000000000b
<4>Call Trace:
<4> [<ffffffff810634c7>] complete+0x47/0x60
<4> [<ffffffffa01d37e7>] qedf_fip_recv+0x1c7/0x450 [qedf]
<4> [<ffffffffa01cb3cb>] qedf_ll2_recv_thread+0x33b/0x510 [qedf]
<4> [<ffffffffa01cb090>] ? qedf_ll2_recv_thread+0x0/0x510 [qedf]
<4> [<ffffffff810a662e>] kthread+0x9e/0xc0
<4> [<ffffffff8100c28a>] child_rip+0xa/0x20
<4> [<ffffffff810a6590>] ? kthread+0x0/0xc0
<4> [<ffffffff8100c280>] ? child_rip+0x0/0x20
<4>Code: 41 56 41 55 41 54 53 48 83 ec 18 0f 1f 44 00 00 89 75 cc 89 55 c8 4c 8d 6f 08 48 8b 57 08 41 89 cf 4d 89 c6 48 8d 42 e8 49 39 d5 <48> 8b 58 18 74 3f 48 83 eb 18 eb 0a 0f 1f 00 48 89 d8 48 8d 5a
<1>RIP [<ffffffff8105ed71>] __wake_up_common+0x31/0x90
<4> RSP <ffff881068a83d50>
<4>CR2: 0000000000000000
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Cc: <stable@vger.kernel.org>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.
[mkp: tweaked to avoid setting rw_max twice and added typecast]
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ca369d51b3e ("block/sd: Fix device-imposed transfer length limits")
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix ThunderX legacy firmware resources
- fix ARTPEC-6 and DesignWare platform driver NULL pointer dereferences
- fix HiSilicon link error
* tag 'pci-v4.11-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dwc: Fix dw_pcie_ops NULL pointer dereference
PCI: dwc: Select PCI_HOST_COMMON for hisi
PCI: thunder-pem: Fix legacy firmware PEM-specific resources
|
|
While running the srp-test software I noticed that request
processing stalls sporadically at the beginning of a test, namely
when mkfs is run against a dm-mpath device. Every time when that
happened the following command was sufficient to resume request
processing:
echo run >/sys/kernel/debug/block/dm-0/state
This patch avoids that such request processing stalls occur. The
test I ran is as follows:
while srp-test/run_tests -d -r 30 -t 02-mq; do :; done
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If a .queue_rq() function returns BLK_MQ_RQ_QUEUE_BUSY then the block
driver that implements that function is responsible for rerunning the
hardware queue once requests can be queued again successfully.
commit 52d7f1b5c2f3 ("blk-mq: Avoid that requeueing starts stopped
queues") removed the blk_mq_stop_hw_queue() call from scsi_queue_rq()
for the BLK_MQ_RQ_QUEUE_BUSY case. Hence change all calls to functions
that are intended to rerun a busy queue such that these examine all
hardware queues instead of only stopped queues.
Since no other functions than scsi_internal_device_block() and
scsi_internal_device_unblock() should ever stop or restart a SCSI
queue, change the blk_mq_delay_queue() call into a
blk_mq_delay_run_hw_queue() call.
Fixes: commit 52d7f1b5c2f3 ("blk-mq: Avoid that requeueing starts stopped queues")
Fixes: commit 7e79dadce222 ("blk-mq: stop hardware queue in blk_mq_delay_queue()")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- two stable fixes for the verity target's FEC support
- a stable fix for raid target's raid1 support (when no bitmap is used)
- a 4.11 cache metadata v2 format fix to properly test blocks are clean
* tag 'dm-4.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity fec: fix bufio leaks
dm raid: fix NULL pointer dereference for raid1 without bitmap
dm cache metadata: fix metadata2 format's blocks_are_clean_separate_dirty
dm verity fec: limit error correction recursion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This fixes a core device enumeration code change made in 4.10, in
order to address a reported issue, that went too far.
Specifics:
- Refine the check for the existence of _HID in find_child_checks()
so that it doesn't trigger for device objects with device IDs made
up by the kernel (Rafael Wysocki)"
* tag 'acpi-4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Prefer devices without _HID for _ADR matching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fix from Juergen Gross:
"A fix for error path cleanup in the xenbus handler"
* tag 'for-linus-4.11b-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xenbus: remove transaction holder from list before freeing
|
|
Connecting to the backend isn't working reliably in xen-fbfront: in
case XenbusStateInitWait of the backend has been missed the backend
transition to XenbusStateConnected will trigger the connected state
only without doing the actions required when the backend has
connected.
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
SSD1306 needs VBAT when it is wired in charge pump configuration only.
Other controllers of the SSD1307 family do not need it at all. This was
introduced by commit ba14301e0356 ("fbdev/ssd1307fb: add support to
enable VBAT").
Without VBAT configuration the driver now fails with:
failed to get VBAT regulator: -19
This is caused by misinterpretation of devm_regulator_get_optional
which "returns a struct regulator corresponding to the regulator
producer or IS_ERR() condition".
Handle -ENODEV without bailing out and making VBAT support really
optional.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
[b.zolnierkie: minor fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
We try to disable callbacks on c_ivq even without multiport
even though that vq is not initialized in this configuration.
Fixes: c743d09dbd01 ("virtio: console: Disable callbacks for virtqueues at start of S4 freeze")
Suggested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
virtio attempts to clear the MTU feature bit if the value is out of the
supported range, but this has no real effect since FEATURES_OK has
already been set.
Fix this up by checking the MTU in the new validate callback.
Fixes: 14de9d114a82 ("virtio-net: Add initial MTU advice feature")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Some drivers can't support all features in all configurations. At the
moment we blindly set FEATURES_OK and later FAILED. Support this better
by adding a callback drivers can use to do some early checks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
If one enables e.g. jumbo frames without mergeable
buffers, packets won't fit in 1500 byte buffers
we use. Switch to big packet mode instead.
TODO: make sizing more exact, possibly extend small
packet mode to use larger pages.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
* acpi-scan-fixes:
ACPI / scan: Prefer devices without _HID for _ADR matching
|
|
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc10 ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea76 ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit f6988cb63a4e ("team: don't call netdev_change_features under
team->lock") fixed the issue calling netdev_change_features under
team->lock for team_compute_features.
But there are still two places where it calls netdev_change_features
under team->lock, team_port_add and team_port_del. It may cause a
dead lock when the slave port with LRO enabled is added.
This patch is to fix this dead lock by moving netdev_change_features
out of team_port_add and team_port_del, and call it after unlocking
the team lock.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
