| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The slab shrinkers are currently invoked from the zonelist walkers in
kswapd, direct reclaim, and zone reclaim, all of which roughly gauge the
eligible LRU pages and assemble a nodemask to pass to NUMA-aware
shrinkers, which then again have to walk over the nodemask. This is
redundant code, extra runtime work, and fairly inaccurate when it comes to
the estimation of actually scannable LRU pages. The code duplication will
only get worse when making the shrinkers cgroup-aware and requiring them
to have out-of-band cgroup hierarchy walks as well.
Instead, invoke the shrinkers from shrink_zone(), which is where all
reclaimers end up, to avoid this duplication.
Take the count for eligible LRU pages out of get_scan_count(), which
considers many more factors than just the availability of swap space, like
zone_reclaimable_pages() currently does. Accumulate the number over all
visited lruvecs to get the per-zone value.
Some nodes have multiple zones due to memory addressing restrictions. To
avoid putting too much pressure on the shrinkers, only invoke them once
for each such node, using the class zone of the allocation as the pivot
zone.
For now, this integrates the slab shrinking better into the reclaim logic
and gets rid of duplicative invocations from kswapd, direct reclaim, and
zone reclaim. It also prepares for cgroup-awareness, allowing
memcg-capable shrinkers to be added at the lruvec level without much
duplication of both code and runtime work.
This changes kswapd behavior, which used to invoke the shrinkers for each
zone, but with scan ratios gathered from the entire node, resulting in
meaningless pressure quantities on multi-zone nodes.
Zone reclaim behavior also changes. It used to shrink slabs until the
same amount of pages were shrunk as were reclaimed from the LRUs. Now it
merely invokes the shrinkers once with the zone's scan ratio, which makes
the shrinkers go easier on caches that implement aging and would prefer
feeding back pressure from recently used slab objects to unused LRU pages.
[vdavydov@parallels.com: assure class zone is populated]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is just a small optimization. The start_pfn can be obtained directly
by phys_index << PFN_SECTION_SHIFT. So the call of page_to_pfn() is
redundant and remove it.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This could be useful for debug in the future if we want to track
major/minor faults more closely, and also avoids the put_page trick we
used with gup.
In order to do this, we also track the task struct in the PASID state
structure. This lets us update the appropriate task stats after the fault
has been handled, and may aid with debug in the future as well.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Oded Gabbay <oded.gabbay@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 7654e9d4fd8f ("drivers/rtc/rtc-snvs: fix suspend/resume")
replaces SIMPLE_DEV_PM_OPS with direct declaration of snvs_rtc_pm_ops,
but does so outside #ifdef CONFIG_PM_SLEEP. This causes the driver
build to fail if CONFIG_PM_SLEEP is not configured.
Fixes: 7654e9d4fd8f ("drivers/rtc/rtc-snvs: fix suspend/resume")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree update from Jiri Kosina:
"Usual stuff: documentation updates, printk() fixes, etc"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
intel_ips: fix a type in error message
cpufreq: cpufreq-dt: Move newline to end of error message
ps3rom: fix error return code
treewide: fix typo in printk and Kconfig
ARM: dts: bcm63138: change "interupts" to "interrupts"
Replace mentions of "list_struct" to "list_head"
kernel: trace: fix printk message
scsi: mpt2sas: fix ioctl in comment
zbud, zswap: change module author email
clocksource: Fix 'clcoksource' typo in comment
arm: fix wording of "Crotex" in CONFIG_ARCH_EXYNOS3 help
gpio: msm-v1: make boolean argument more obvious
usb: Fix typo in usb-serial-simple.c
PCI: Fix comment typo 'COMFIG_PM_OPS'
powerpc: Fix comment typo 'CONIFG_8xx'
powerpc: Fix comment typos 'CONFiG_ALTIVEC'
clk: st: Spelling s/stucture/structure/
isci: Spelling s/stucture/structure/
usb: gadget: zero: Spelling s/infrastucture/infrastructure/
treewide: Fix company name in module descriptions
...
|
|
Pull UBI/UBIFS updates from Artem Bityutskiy:
"This includes the following UBI/UBIFS changes:
- UBI debug messages now include the UBI device number. This change
is responsible for the big diffstat since it touched every
debugging print statement.
- An Xattr bug-fix which fixes SELinux support
- Several error path fixes in UBI/UBIFS"
* tag 'upstream-3.19-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Fix invalid vfree()
UBI: Fix double free after do_sync_erase()
UBIFS: fix a couple bugs in UBIFS xattr length calculation
UBI: vtbl: Use ubi_eba_atomic_leb_change()
UBI: Extend UBI layer debug/messaging capabilities
UBIFS: fix budget leak in error path
|
|
'for-3.19/lenovo', 'for-3.19/logitech', 'for-3.19/microsoft', 'for-3.19/plantronics', 'for-3.19/rmi', 'for-3.19/sony' and 'for-3.19/wacom' into for-linus
|
|
registers are present
If a touchpad does not report relative data then query 6 will not be present and the address
of query 8 will be one less. This patches calculates the location of query 8 instead of
hardcoding the offset.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If a touchpad reports the F11 data40 register then this indicates that the touchpad reports
additional ACM (Accidental Contact Mitigation) data after the F11 data in the HID attention
report. These additional bytes shift the position of the F30 button data causing the driver
to incorrectly report button state when this functionality is present. This patch accounts
for the additional data in the report.
Fixes:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1398533
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Conflicts:
drivers/hid/hid-input.c
|
|
Before ->start() is called, bufsize size is set to HID_MIN_BUFFER_SIZE,
64 bytes. While processing the IRQ, we were asking to receive up to
wMaxInputLength bytes, which can be bigger than 64 bytes.
Later, when ->start is run, a proper bufsize will be calculated.
Given wMaxInputLength is said to be unreliable in other part of the
code, set to receive only what we can even if it results in truncated
reports.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata changes from Tejun Heo:
"The only interesting piece is the support for shingled drives. The
changes in libata layer are minimal. All it does is identifying the
new class of device and report upwards accordingly"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Remove FIXME comment in atapi_request_sense()
sata_rcar: Document deprecated "renesas,rcar-sata"
sata_rcar: Add clocks to sata_rcar bindings
ahci_sunxi: Make AHCI_HFLAG_NO_PMP flag configurable with a module option
libata-scsi: Update SATL for ZAC drives
libata: Implement ATA_DEV_ZAC
libsas: use ata_dev_classify()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
|
|
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"The most notable change for this pull request is the ftrace rework
from Heiko. It brings a small performance improvement and the ground
work to support a new gcc option to replace the mcount blocks with a
single nop.
Two new s390 specific system calls are added to emulate user space
mmio for PCI, an artifact of the how PCI memory is accessed.
Two patches for the memory management with changes to common code.
For KVM mm_forbids_zeropage is added which disables the empty zero
page for an mm that is used by a KVM process. And an optimization,
pmdp_get_and_clear_full is added analog to ptep_get_and_clear_full.
Some micro optimization for the cmpxchg and the spinlock code.
And as usual bug fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (46 commits)
s390/cputime: fix 31-bit compile
s390/scm_block: make the number of reqs per HW req configurable
s390/scm_block: handle multiple requests in one HW request
s390/scm_block: allocate aidaw pages only when necessary
s390/scm_block: use mempool to manage aidaw requests
s390/eadm: change timeout value
s390/mm: fix memory leak of ptlock in pmd_free_tlb
s390: use local symbol names in entry[64].S
s390/ptrace: always include vector registers in core files
s390/simd: clear vector register pointer on fork/clone
s390: translate cputime magic constants to macros
s390/idle: convert open coded idle time seqcount
s390/idle: add missing irq off lockdep annotation
s390/debug: avoid function call for debug_sprintf_*
s390/kprobes: fix instruction copy for out of line execution
s390: remove diag 44 calls from cpu_relax()
s390/dasd: retry partition detection
s390/dasd: fix list corruption for sleep_on requests
s390/dasd: fix infinite term I/O loop
s390/dasd: remove unused code
...
|
|
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
|
|
Balance a hid_device_io_start() call with hid_device_io_stop() in the
error path. This avoids processing of HID reports when the probe fails
which possibly leads to invalid memory access in hid_device_probe() as
report_enum->report_id_hash might already be freed via
hid_close_report().
hid_set_drvdata() is called before wtp_allocate, be consistent and clear
drvdata too on the error path of wtp_allocate.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The HID response has a limited size. Do not trust the value returned by
hardware, check that it really fits in the message.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hidpp_devicenametype_get_device_name() may return a negative value on
protocol errors (for example, when the device is powered off).
Explicitly check this condition to avoid a long-running loop.
(0 cannot be returned as __name_length - index > 0, but check for it
anyway as it would otherwise result in an infinite loop.)
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We do not make any use of the actual name length get through
hidpp_get_device_name(). Original patch by Benjamin Tissoires, this
patch also replaces a (now) unnecessary goto by return NULL.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a fairly large pull request. In addition to the usual
driver updates / fixes, there have been a high amount of cleanups in
ASoC area, as well as control API helpers and kernel documentations
fixes touching through the whole tree.
In the driver side, the biggest changes are the support for new Intel
SoC found on new x86 machines, and the updates of FireWire dice and
oxfw drivers.
Some remarkable items are below:
ALSA core:
- PCM mmap code cleanup, removal of arch-dependent codes
- PCM xrun injection support
- PCM hwptr tracepoint support
- Refactoring of snd_pcm_action(), simplification of PCM locking
- Robustified sequecner auto-load functionality
- New control API helpers and lots of cleanups along with them
- Lots of kerneldoc fixes and cleanups
USB-audio:
- The mixer resume code was largely rewritten, and the devices with
quirks are resumed properly.
- New hardware support: Focusrite Scarlett, Digidesign Mbox1,
Denon/Marantz DACs, Zoom R16/24
FireWire:
- DICE driver updates with better duplex and sync support, including
MIDI support
- New OXFW driver for Oxford Semiconductor FW970/971 chipset,
including the previous LaCie Speakers device. Fullduplex and MIDI
support included as well as DICE driver.
HD-audio:
- Refactoring the driver-caps quirk handling in snd-hda-intel
- More consistent control names representing the topology better
- Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
fix, ASUS Z99He laptop EAPD
ASoC:
- Conversion of AC'97 drivers to use regmap, bringing us closer to
the removal of the ASoC level I/O code
- Clean up a lot of old drivers that were open coding things that
have subsequently been implemented in the core
- Some DAPM performance improvements
- Removal of the now seldom used CODEC mutex
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers
- Support for Samsung boards using rt5631 as the CODEC
- Removal of the obsolete AFEB9260 machine driver
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks
Others:
- ASIHPI driver update and cleanups
- Lots of dev_*() printk conversions
- Lots of trivial cleanups for the codes spotted by Coccinelle"
* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: pcxhr: NULL dereference on probe failure
ALSA: lola: NULL dereference on probe failure
ALSA: hda - Add "eapd" model string for AD1986A codec
ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
ALSA: oxfw: Add hwdep interface
ALSA: oxfw: Add support for capture/playback MIDI messages
ALSA: oxfw: add support for capturing PCM samples
ALSA: oxfw: Add support AMDTP in-stream
ALSA: oxfw: Add support for Behringer/Mackie devices
ALSA: oxfw: Change the way to start stream
ALSA: oxfw: Add proc interface for debugging purpose
ALSA: oxfw: Change the way to make PCM rules/constraints
ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
ALSA: oxfw: Change the way to name card
ALSA: dice: Add support for MIDI capture/playback
ALSA: dice: Add support for capturing PCM samples
ALSA: dice: Support for non SYT-Match sampling clock source mode
ALSA: dice: Add support for duplex streams with synchronization
ALSA: dice: Change the way to start stream
ALSA: jack: Add dummy snd_jack_set_key() definition
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- support for mx6sl and mx6sx
- OMAP HDMI audio rewrite to make it finally work
- OMAP video PLL work to prepare for new DRA7xx SoCs
- simplefb DT related improvements
* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
video: smscufx: Deletion of unnecessary checks before the function call "vfree"
video: udlfb: Deletion of unnecessary checks before the function call "vfree"
video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
video: fbdev: arkfb: suppress build warning
video: fbdev: s3fb: suppress build warning
video: fbdev: vt8623fb: suppress build warning
OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
OMAPDSS: Remove all references to obsolete HDMI audio callbacks
ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
...
|
|
Pull virtio updates from Michael Tsirkin:
"virtio: virtio 1.0 support, misc patches
This adds a lot of infrastructure for virtio 1.0 support. Notable
missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Note: some net drivers are affected by these patches. David said he's
fine with merging these patches through my tree.
Rusty's on vacation, he acked using my tree for these, too"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
virtio_ccw: finalize_features error handling
virtio_ccw: future-proof finalize_features
virtio_pci: rename virtio_pci -> virtio_pci_common
virtio_pci: update file descriptions and copyright
virtio_pci: split out legacy device support
virtio_pci: setup config vector indirectly
virtio_pci: setup vqs indirectly
virtio_pci: delete vqs indirectly
virtio_pci: use priv for vq notification
virtio_pci: free up vq->priv
virtio_pci: fix coding style for structs
virtio_pci: add isr field
virtio: drop legacy_only driver flag
virtio_balloon: drop legacy_only driver flag
virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
virtio: allow finalize_features to fail
virtio_ccw: legacy: don't negotiate rev 1/features
virtio: add API to detect legacy devices
virtio_console: fix sparse warnings
vhost: remove unnecessary forward declarations in vhost.h
...
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox framework updates from Jassi Brar.
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
Mailbox: Add support for Platform Communication Channel
mailbox/omap: adapt to the new mailbox framework
mailbox: add tx_prepare client callback
mailbox: Don't unnecessarily re-arm the polling timer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not a huge amount going on this release, mainly new drivers (there's a
couple more waiting that didn't quite make the cut for this release
too):
- An interface for querying if the current transfer is the last in a
message, allowing controllers that need special handling for the
final transfer to use the core message parsing.
- Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
Intel Quark X1000 and Samsung Exynos 7 controllers"
* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
spi/s3c64xx: Remove redundant runtime PM management
spi: fsl-spi: remove unused variable assignment
spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
spi: core: Do not mangle error code from kthread_run()
spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
spi: fsl-(e)spi: migrate to generic master queueing
spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
spi: cadence: Fix 3-to-8 mux mode
spi: cadence: Init HW after reading devicetree attributes
spi: meson: Select REGMAP_MMIO
spi: s3c64xx: add support for exynos7 SPI controller
spi: spi-pxa2xx: SPI support for Intel Quark X1000
spi: meson: meson_spifc_setup_speed() can be static
spi: spi-pxa2xx: Add helpers for regiseters' accessing
spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
spi: atmel: introduce probe deferring
spi: atmel: remove compat for non DT board when requesting dma chan
spi: meson: Add support for Amlogic Meson SPIFC
spi: meson: Add device tree bindings documentation for SPIFC
spi: core: Add spi_transfer_is_last() helper
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac
Pull edac updates from Mauro Carvalho Chehab:
- Broadwell-DE support on sb-edac driver
- Some fixes at sb-edac driver
* tag 'edac/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: Fix typo computing number of banks
sb_edac: Add support for Broadwell-DE processor
sb_edac: Fix discovery of top-of-low-memory for Haswell
sb_edac: Fix erroneous bytes->gigabytes conversion
sb_edac: Fix off-by-one error in number of channels
|
|
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->mac_header
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
|
|
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.
The different A0 DMFS (steering) modes are:
Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.
Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.
Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).
Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.
Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.
In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.
Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was dropped by mistake for the napi_gro_frags flow, fix that.
Fixes: dd65beac48a5 ('net/mlx4_en: Extend usage of napi_gro_frags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
|
|
The encapsulated offload flags shouldn't be unconditionally exported
to the stack. The stack expects offloading to work across all tunnel
types when those flags are set. This would break other tunnels (like
GRE) since be2net currently supports tunnel offload for VxLAN only.
Also, with VxLANs Skyhawk-R can offload only 1 UDP dport. If more
than 1 UDP port is added, we should disable offloads in that case too.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
WARNING: at lib/dma-debug.c:1140
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
task: c0834300 ti: effe6000 task.ti: c0874000
NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029)
MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000
GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003
GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678
GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44
GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0
NIP [c02b2c98] check_unmap+0x51c/0x9e4
LR [c02b2c98] check_unmap+0x51c/0x9e4
Call Trace:
[effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable)
[effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c
[effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488
[effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8
[effe7f60] [c04f8714] net_rx_action+0xc0/0x178
[effe7f90] [c00435a0] __do_softirq+0x100/0x1fc
[effe7fe0] [c0043958] irq_exit+0xa4/0xc8
[effe7ff0] [c000d14c] call_do_irq+0x24/0x3c
[c0875e90] [c00048a0] do_IRQ+0x8c/0xf8
[c0875eb0] [c000ed10] ret_from_except+0x0/0x18
For TX, we need to unmap the pages which has already been mapped and
free the skb before return.
For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove use of calls into t4_fw_hello() with MASTER_MUST, which results in
FW_HELLO_CMD_MASTERFORCE being set. The firmware doesn't support this and of
course any existing PF Drivers will totally go for a toss.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Here are the PCI changes intended for v3.19. I don't think there's
anything very exciting here, but there was a lot of MSI-related stuff
coming via Thomas.
Details:
NUMA
- Allow numa_node override via sysfs (Prarit Bhargava)
Resource management
- Restore detection of read-only BARs (Myron Stowe)
- Shrink decoding-disabled window while sizing BARs (Myron Stowe)
- Add informational printk for invalid BARs (Myron Stowe)
- Remove fixed parameter in pci_iov_resource_bar() (Myron Stowe)
MSI
- Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits (Yijing Wang)
- Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()" (Yijing Wang)
- s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq() (Yijing Wang)
Virtualization
- xen: Process failure for pcifront_(re)scan_root() (Chen Gang)
- Make FLR and AF FLR reset warning messages different (Gavin Shan)
Generic host bridge driver
- Allocate config space windows after limiting bus number range (Lorenzo Pieralisi)
- Convert to DT resource parsing API (Lorenzo Pieralisi)
Freescale Layerscape
- Add Freescale Layerscape PCIe driver (Minghuan Lian)
NVIDIA Tegra
- Do not build on 64-bit ARM (Thierry Reding)
- Add Kconfig help text (Thierry Reding)
Renesas R-Car
- Make rcar_pci static (Jingoo Han)
Samsung Exynos
- Add exynos prefix to add_pcie_port(), pcie_init() (Jingoo Han)
ST Microelectronics SPEAr13xx
- Add spear prefix to add_pcie_port(), pcie_init() (Jingoo Han)
- Make spear13xx_add_pcie_port() __init (Jingoo Han)
- Remove unnecessary OOM message (Jingoo Han)
TI DRA7xx
- Add dra7xx prefix to add_pcie_port() (Jingoo Han)
- Make dra7xx_add_pcie_port() __init (Jingoo Han)
TI Keystone
- Make ks_dw_pcie_msi_domain_ops static (Jingoo Han)
- Remove unnecessary OOM message (Jingoo Han)
Miscellaneous
- Delete unnecessary NULL pointer checks (Markus Elfring)
- Remove unused to_hotplug_slot() (Gavin Shan)
- Whitespace cleanup (Jingoo Han)
- Simplify if-return sequences (Quentin Lambert)"
* tag 'pci-v3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (28 commits)
PCI: Remove fixed parameter in pci_iov_resource_bar()
PCI: Add informational printk for invalid BARs
PCI: tegra: Add Kconfig help text
PCI: tegra: Do not build on 64-bit ARM
PCI: spear: Remove unnecessary OOM message
PCI: mvebu: Add a blank line after declarations
PCI: designware: Add a blank line after declarations
PCI: exynos: Remove unnecessary return statement
PCI: imx6: Use tabs for indentation
PCI: keystone: Remove unnecessary OOM message
PCI: Remove unused and broken to_hotplug_slot()
PCI: Make FLR and AF FLR reset warning messages different
PCI: dra7xx: Add __init annotation to dra7xx_add_pcie_port()
PCI: spear: Add __init annotation to spear13xx_add_pcie_port()
PCI: spear: Rename add_pcie_port(), pcie_init() to spear13xx_add_pcie_port(), etc.
PCI: dra7xx: Rename add_pcie_port() to dra7xx_add_pcie_port()
PCI: layerscape: Add Freescale Layerscape PCIe driver
PCI: Simplify if-return sequences
PCI: Delete unnecessary NULL pointer checks
PCI: Shrink decoding-disabled window while sizing BARs
...
|
