| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Reduce bloated code by converting the driver to module_i2c_driver().
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Update si4713 driver to support being instantiated via
Device Tree. This includes moving the regulator names
back into the drivers, using regulator_get_optional
to avoid breaking the USB driver and switching to the
gpio resource interface.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Move sysfs_notify and i2c_transfer calls from bq2415x_notifier_call
to bq2415x_timer_work to avoid sleeping in atomic context.
This fixes the following bug:
[ 7.667449] Workqueue: events power_supply_changed_work
[ 7.673034] [<c0015c28>] (unwind_backtrace+0x0/0xe0) from [<c0011e1c>] (show_stack+0x10/0x14)
[ 7.682098] [<c0011e1c>] (show_stack+0x10/0x14) from [<c052cdd0>] (dump_stack+0x78/0xac)
[ 7.690704] [<c052cdd0>] (dump_stack+0x78/0xac) from [<c052a044>] (__schedule_bug+0x48/0x60)
[ 7.699645] [<c052a044>] (__schedule_bug+0x48/0x60) from [<c053071c>] (__schedule+0x74/0x638)
[ 7.708618] [<c053071c>] (__schedule+0x74/0x638) from [<c05301fc>] (schedule_timeout+0x1dc/0x24c)
[ 7.718017] [<c05301fc>] (schedule_timeout+0x1dc/0x24c) from [<c05316ec>] (wait_for_common+0x138/0x17c)
[ 7.727966] [<c05316ec>] (wait_for_common+0x138/0x17c) from [<c0362a70>] (omap_i2c_xfer+0x340/0x4a0)
[ 7.737640] [<c0362a70>] (omap_i2c_xfer+0x340/0x4a0) from [<c035d928>] (__i2c_transfer+0x40/0x74)
[ 7.747039] [<c035d928>] (__i2c_transfer+0x40/0x74) from [<c035e22c>] (i2c_transfer+0x6c/0x90)
[ 7.756195] [<c035e22c>] (i2c_transfer+0x6c/0x90) from [<c037ad24>] (bq2415x_i2c_write+0x48/0x78)
[ 7.765563] [<c037ad24>] (bq2415x_i2c_write+0x48/0x78) from [<c037ae60>] (bq2415x_set_weak_battery_voltage+0x4c/0x50)
[ 7.776824] [<c037ae60>] (bq2415x_set_weak_battery_voltage+0x4c/0x50) from [<c037bce8>] (bq2415x_set_mode+0xdc/0x14c)
[ 7.788085] [<c037bce8>] (bq2415x_set_mode+0xdc/0x14c) from [<c037bfb8>] (bq2415x_notifier_call+0xa8/0xb4)
[ 7.798309] [<c037bfb8>] (bq2415x_notifier_call+0xa8/0xb4) from [<c005f228>] (notifier_call_chain+0x38/0x68)
[ 7.808715] [<c005f228>] (notifier_call_chain+0x38/0x68) from [<c005f284>] (__atomic_notifier_call_chain+0x2c/0x3c)
[ 7.819732] [<c005f284>] (__atomic_notifier_call_chain+0x2c/0x3c) from [<c005f2a8>] (atomic_notifier_call_chain+0x14/0x18)
[ 7.831420] [<c005f2a8>] (atomic_notifier_call_chain+0x14/0x18) from [<c0378078>] (power_supply_changed_work+0x6c/0xb8)
[ 7.842864] [<c0378078>] (power_supply_changed_work+0x6c/0xb8) from [<c00556c0>] (process_one_work+0x248/0x440)
[ 7.853546] [<c00556c0>] (process_one_work+0x248/0x440) from [<c0055d6c>] (worker_thread+0x208/0x350)
[ 7.863372] [<c0055d6c>] (worker_thread+0x208/0x350) from [<c005b0ac>] (kthread+0xc8/0xdc)
[ 7.872131] [<c005b0ac>] (kthread+0xc8/0xdc) from [<c000e138>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Update rx51-battery driver to use the new IIO API of
twl4030-madc and add DT support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
|
|
Add iio_read_channel_average_raw to support reading
averaged raw values in consumer drivers.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds support for the the wakeup threshold and
support for the second wakeup unit to the DT based
setup.
Signed-off-by: Sebastian Reichel <sre@debian.org>
|
|
st,axis-{x,y,z} can be negative to imply inverted
axis.
Apart from that the minimal and maximal threshold
may be negative.
Signed-off-by: Sebastian Reichel <sre@debian.org>
|
|
This adds DT support to the tsc2005 touchscreen
driver.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Simplify the driver by using managed resources for memory allocation of
internal struct, input device allocation and irq request.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Change some dev_dbg() invocations to dev_err() ones, because they
are supposed to output error messages.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.
The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This temporarily fixes building the Nokia N900 IR driver.
There is currently work going on putting dmtimer into
drivers/ and adding a public API. Until that has happened
this hack is needed to keep ir-rx51 compiling.
Signed-off-by: Sebastian Reichel <sre@debian.org>
|
|
This updates the Nokia N900 IR driver to use the common
clock framework instead of omap platform code.
Signed-off-by: Sebastian Reichel <sre@debian.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"A small batch of GPIO fixes for the v3.15 series. I expect more to
come in but I'm a bit behind on mail, might as well get these to you
right now:
- Change a crucial semantic ordering in the GPIO irqchip helpers
- Fix two nasty regressions in the ACPI gpiolib extensions"
* tag 'gpio-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio / ACPI: Prevent potential wrap of GPIO value on OpRegion read
gpio / ACPI: Don't crash on NULL chip->dev
gpio: set data first, then chip and handler
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Back from long weekend here in India and now the time to send fixes
for slave dmaengine.
- Dan's fix of sirf xlate code
- Jean's fix for timberland
- edma fixes by Sekhar for SG handling and Yuan for changing init
call"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix eDMA driver as a subsys_initcall
dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
platform: Fix timberdale dependencies
dma: edma: fix incorrect SG list handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Fixes for regressions:
- fix wrong IOMMU enumeration causing some SCSI device drivers
initialization failures
- ARM-SMMU fixes for a panic condition and a wrong return value"
* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
iommu/arm-smmu: Return 0 on unmap failure
iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
iommu/vt-d: fix memory leakage caused by commit ea8ea46
|
|
Pull drm fixes from Dave Airlie:
"Unfortunately this contains no easter eggs, its a bit larger than I'd
like, but I included a patch that just moves code from one file to
another and I'd like to avoid merge conflicts with that later, so it
makes it seem worse than it is,
Otherwise:
- radeon: fixes to use new microcode to stabilise some cards, use
some common displayport code, some runtime pm fixes, pll regression
fixes
- i915: fix for some context oopses, a warn in a used path, backlight
fixes
- nouveau: regression fix
- omap: a bunch of fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
drm: bochs: drop unused struct fields
drm: bochs: add power management support
drm: cirrus: add power management support
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
drm/plane-helper: Don't fake-implement primary plane disabling
drm/ast: fix value check in cbr_scan2
drm/nouveau/bios: fix a bit shift error introduced by 457e77b
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
drm/tegra: Remove gratuitous pad field
...
|
|
git://people.freedesktop.org/~deathsimple/linux into drm-next
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
|
|
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging driver fixes for issues that have been reported
for 3.15-rc2.
Also dominating the diffstat for the pull request is the removal of
the rtl8187se driver. It's no longer needed in staging as a "real"
driver for this hardware is now merged in the tree in the "correct"
location in drivers/net/
All of these patches have been tested in linux-next"
* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
staging: comedi: fix circular locking dependency in comedi_mmap()
staging: r8723au: Add missing initialization of change_inx in sort algorithm
Staging: unisys: use after free in list_for_each()
staging: unisys: use after free in error messages
staging: speakup: fix misuse of kstrtol() in handle_goto()
staging: goldfish: Call free_irq in error path
staging: delete rtl8187se wireless driver
staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
staging: gs_fpgaboot: remove __TIMESTAMP__ macro
staging: vme: fix memory leak in vme_user_probe()
staging: fpgaboot: clean up Makefile
staging/usbip: fix store_attach() sscanf return value check
staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
Nothing major, just issues some people have reported.
All of these have been in linux-next"
* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
uas: fix deadlocky memory allocations
uas: fix error handling during scsi_scan()
uas: fix GFP_NOIO under spinlock
uwb: adds missing error handling
USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
USB: ohci-jz4740: Fix uninitialized variable warning
USB: EHCI: tegra: set txfill_tuning
usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
USB: fix crash during hotplug of PCI USB controller card
USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
usb: usb-common: fix typo for usb_state_string
USB: usb_wwan: fix handling of missing bulk endpoints
USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: cp210x: Add 8281 (Nanotec Plug & Drive)
usb: option driver, add support for Telit UE910v2
Revert "USB: serial: add usbid for dell wwan card to sierra.c"
USB: serial: ftdi_sio: add id for Brainboxes serial cards
|
|
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
|
|
shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company. Replace ST's id with shiraz.linux.kernel@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-04-17
Please pull this batch of fixes intended for the 3.15 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Chun-Yeow to not look at management frame bitrates
that are typically really low, two fixes from Felix for AP_VLAN
interfaces, a fix from Ido to disable SMPS settings when a monitor
interface is enabled, a radar detection fix from Michał and a fix from
myself for a very old remain-on-channel bug."
For the iwlwifi bits, Emmanuel says:
"I have new device IDs and a new firmware API. These are the trivial
ones. The less trivial ones are Johannes's fix that delays the
enablement of an interrupt coalescing hardware until after association
- this fixes a few connection problems seen in the field. Eyal has a
bunch of rate control fixes. I decided to add these for 3.15 because
they fix some disconnection and packet loss scenarios which were
reported by the field. I also have a fix for a memory leak that
happens only with a very new NIC."
Along with those...
Amitkumar Karwar fixes a couple of problems relating to driver/firmware
interactions in mwifiex.
Christian Engelmayer avoids a couple of potential memory leaks in
the new rsi driver.
Eliad Peller provides a wl18xx mailbox alignment fix for problems
when using new firmware.
Frederic Danis adds a couple of missing debugging strings to the
cw1200 driver.
Geert Uytterhoeven adds a variable initialization inside of the
rsi driver.
Luciano Coelho patches the wlcore code to ignore dummy packet events
in PLT mode in order to work around a firmware bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes a problem with dropped jumbo frames after usage of
'ethtool -G ... rx'.
Scenario:
1. ip link set eth0 up
2. ethtool -G eth0 rx N # <- This zeroes rx-jumbo
3. ip link set mtu 9000 dev eth0
The ethtool command set rx_jumbo_pending to zero so any received jumbo
packets are dropped and you need to use 'ethtool -G eth0 rx-jumbo N'
to workaround the issue.
The patch changes the logic so rx_jumbo_pending value is changed only if
jumbo frames are enabled (MTU > 1500).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree
- drop deprecated MSI-X API use.
- a couple other miscellaneous things.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix over-dereference when terminating
RDMA/cxgb4: Use uninitialized_var()
RDMA/cxgb4: Add missing debug stats
RDMA/cxgb4: Initialize reserved fields in a FW work request
RDMA/cxgb4: Use pr_warn_ratelimited
RDMA/cxgb4: Max fastreg depth depends on DSGL support
RDMA/cxgb4: SQ flush fix
RDMA/cxgb4: rmb() after reading valid gen bit
RDMA/cxgb4: Endpoint timeout fixes
RDMA/cxgb4: Use the BAR2/WC path for kernel QPs and T5 devices
IB/mlx5: Add block multicast loopback support
IB/mthca: Use pci_enable_msix_exact() instead of pci_enable_msix()
IB/qib: Use pci_enable_msix_range() instead of pci_enable_msix()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"These are fixes for a powerpc NULL pointer dereference, an OF
interrupt mapping issue on some of the new host bridges, and a
DesignWare iATU issue.
Host bridge drivers
- Fix OF interrupt mapping for DesignWare, R-Car, Tegra (Lucas Stach)
- Fix DesignWare iATU programming (Mohit Kumar)
Miscellaneous
- Fix powerpc NULL dereference from list_for_each_entry() update (Mike Qiu)"
* tag 'pci-v3.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use new OF interrupt mapping when possible
PCI: rcar: Use new OF interrupt mapping when possible
PCI: designware: Use new OF interrupt mapping when possible
PCI: designware: Fix iATU programming for cfg1, io and mem viewport
PCI: designware: Fix comment for setting number of lanes
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for merge window mismerge in hid-sony, from Frank Praznik
- fix for Surface Type/Touch Cover 2 device, from Benjamin Tissoires
- quirk for ThinkPad Helix sensor hub from Stephen Chandler Paul
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: do not scan constant input report
Revert "HID: microsoft: Add ID's for Surface Type/Touch Cover 2"
HID: sensor-hub: add sensor hub quirk for ThinkPad Helix
HID: sony: Fix cancel_work_sync mismerge
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- fix error handling in of_update_property
- fix section mismatch warnings in __reserved_mem_check_root
- add empty of_find_node_by_path for !OF builds
- add various missing binding documentation
* tag 'dt-fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: add empty of_find_node_by_path() for !OF
of: Clean up of_update_property
DT: add vendor prefix for EBV Elektronik
of: Fix the section mismatch warnings.
of: Add vendor prefix for Digi International Inc.
DT: I2C: Add trivial bindings used by kirkwood boards
DT: Vendor: Add prefixes used by Kirkwood devices
DT: bindings: add missing Marvell Kirkwood SoC documentation
dt-bindings: add vendor-prefix for Newhaven Display
of: add vendor prefix for I2SE GmbH
of: add vendor prefix for ISEE 2007 S.L.
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
bochs kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.
Fix this by adding suspend and resume functions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
cirrus kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.
Fix this by adding suspend and resume functions.
Also make the mode_set function unblank the screen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is leftover stuff from my previous doc round which I kinda wanted
to do but didn't yet due to rebase hell.
The modeset helpers and the probing helpers a independent and e.g.
i915 uses the probing stuff but has its own modeset infrastructure. It
hence makes to split this up. While at it add a DOC: comment for the
probing libraray.
It would be rather neat to pull some of the DocBook documenting these
two helpers into in-line DOC: comments. But unfortunately kerneldoc
doesn't support markdown or something similar to make nice-looking
documentation, so the current state is better.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
After thinking about this topic a bit more I've reached the conclusion
that implementing this doesn't make sense:
- The locking is all wrong: set_config(NULL) will also unlink encoders
and connectors, but those links are protected with the mode_config
mutex. In the ->disable_plane callback we only hold all modeset
locks, but eventually we want to switch to just grabbing the
per-crtc (and maybe per-plane) locks as needed, maybe based on
ww_mutexes. Having a callback which absolutely needs all modeset
locks is bad for this conversion.
Note that the same isn't true for the provided ->update_plane since
we've audited the crtc helpers to make sure that not encoder or
connector links are changed.
- There's no way to re-enable the plane with an ->update_plane: The
connectors/encoder links are lost and so we can't re-enable the
CRTC. Even without that issue the driver might have reassigned some
shared resources (as opposed to e.g. DPMS off, where drivers are not
allowed to do that to make sure the CRTC can be enabled again).
- The semantics don't make much sense: Userspace asked to scan out
black (or some other color if the driver supports a background
color), not that the screen be disabled.
- Implementing proper primary plane support (i.e. actually disabling
the primary plane without disabling the CRTC) is really simple, at
least if all the hw needs is flipping a bit. The big task is
auditing all the interactions with other ioctls when the CRTC is on
but there's no primary plane (e.g. pageflips). And some of that work
still needs to be done.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
this is a typo vs the ums driver, fix to check correct value.
Found initially by Coverity.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit 457e77b26428ab4a24998eecfb99f27fa4195397 added two checks applied to a
value received from nv_rd32(bios, 0x619f04). But after this new piece of code
is executed, the addr local variable does not hold the same value it used to
hold before the commit. Here is what is was assigned in the original code:
(u64)(nv_rd32(bios, 0x619f04) & 0xffffff00) << 8
in the committed code it ends up with this value:
(u64)(nv_rd32(bios, 0x619f04) >> 8) << 8
These expressions are obviously not equivalent.
My Nvidia video card does not show anything on the display when I boot a
kernel containing this commit.
The patch fixes the code so that the new checks are still done, but the
side effect of an incorrect addr value is gone.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
Fixes for omapdrm, some of which were already present in 3.14, and some which
appeared in 3.15-rc1:
- fixes for primary-plane handling which caused crashes
- fix all kinds of uninit issues which prevented from unloading the omapdrm
module.
- fixes for HDMI enable/disable issues
* tag 'omapdrm-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: fix the handling of fb ref counts
drm/omap: protect omap_crtc's event with event_lock spinlock
drm/omap: Use old_fb to synchronize between successive page flips
drm/omap: Fix crash when using LCD3 overlay manager
drm/omap: gem sync: wait on correct events
drm/omap: Fix memory leak in omap_gem_op_async
drm/omap: remove warn from debugfs
drm/omap: remove extra plane->destroy from crtc destroy
drm/omap: print warning when rotating non-TILER fb
drm/omap: fix missing unref to fb's buf object
drm/omap: fix plane rotation
drm/omap: fix enabling/disabling of video pipeline
drm/omap: fix missing disable for unused encoder
drm/omap: fix race issue when unloading omapdrm
drm/omap: fix DMM driver (un)registration
drm/omap: fix uninit order in pdev_remove()
drm/omap: fix output enable/disable sequence
|
|
git://people.freedesktop.org/~deathsimple/linux into drm-next
1. Fixing PLL regressions
2. A couple of memory reclocking and DPM fixes
3. Small cleanups
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v3.15-rc2
This contains a fix for the host1x driver writing to non-existent syncpt
registers.
A second commit removes an excess pad field in the parameter structure
for the DRM_TEGRA_SUBMIT IOCTL. Archeaology on earlier versions of this
file indicates that this was once there to pad an uneven number of u32
u32 fields, of which one was subsequently removed. Unfortunately nobody
remembered to get rid of the padding when that happened.
Both of these commits are Cc: stable because they fix issues that were
introduced back in v3.10.
* tag 'drm/tegra/for-3.15-rc2' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Remove gratuitous pad field
gpu: host1x: handle the correct # of syncpt regs
|
|
Merge ipmi fixes from Corey Minyard:
"Things collected since last kernel release.
Some of these are pretty important. The first three are bug fixes.
The next two are to hopefully make everyone happy about allowing
ACPI to be on all the time and not have IPMI have an effect on the
system when not in use. The last is a little cleanup"
* emailed patches from Corey Minyard <cminyard@mvista.com>:
ipmi: boolify some things
ipmi: Turn off all activity on an idle ipmi interface
ipmi: Turn off default probing of interfaces
ipmi: Reset the KCS timeout when starting error recovery
ipmi: Fix a race restarting the timer
Char: ipmi_bt_sm, fix infinite loop
|
|
Convert some ints to bools.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts. If there is nothing waiting for these events,
it's really kind of pointless to be checking for them. So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these. Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages. And modify the
message handler to not restart the timer if its timer is not needed.
The timers and kthread will still be enabled if:
- the SI interface is handling a message.
- a user has enabled watching for events.
- the IPMI watchdog timer is in use (since it uses pretimeouts).
- the message handler is waiting on a remote response.
- a user has registered to receive commands.
This mostly affects interfaces without interrupts. Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The default probing can cause problems with some system, slow booting,
extra CPU usages, etc. Turn it off by default and give a config option
to enable it.
From: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.
Reported-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time. The thread will not start the timer in that
instance, resulting in the timer not running.
Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer. 'Timer is not running' means that the timer is not
pending and smi_timeout() is not running. So we need a flag to detect
this correctly.
Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In read_all_bytes, we do
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: Rui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from David Vrabel:
"Xen regression and bug fixes for 3.15-rc1:
- fix completely broken 32-bit PV guests caused by x86 refactoring
32-bit thread_info.
- only enable ticketlock slow path on Xen (not bare metal)
- fix two bugs with PV guests not shutting down when requested
- fix a minor memory leak in xen-pciback error path"
* tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/manage: Poweroff forcefully if user-space is not yet up.
xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart.
xen/spinlock: Don't enable them unconditionally.
xen-pciback: silence an unwanted debug printk
xen: fix memory leak in __xen_pcibk_add_pci_dev()
x86/xen: Fix 32-bit PV guests's usage of kernel_stack
|
